Search Documents

John Keith Elers Douglas recently retired from active participation in the activities of the South African Institute of Mining and Metallurgy after over forty years of diligent and valuable service to the Institute. This account of his contributions to the mineral industry and associated organizations is presented as a tribute to all his hard work and dedication. Mineral processing The Fourteenth International Mineral Processing Congress, sponsored by the Canadian Institute of Mining and Metallurgy, is to be held in Toronto from 22nd to 27th October, 1982. The theme of the meeting is 'Worldwide industrial application of mineral technology'.

Jan 1, 1981

By I. M. W. Preston

A new shaft system was required to replace stope face for the North Section of Harmony Mine and to allow for systematic opening up of the North Eastern Section. Owing to the economic circumstances at the time the project started, it became vital to alter the original planning and to sink the service shaft first. The MATLA coal-sinking headgear, a novel presinking arrangement, allowed sinking to continue to 108 m concurrently with the erection of the permanent sinking headgear and sinking winders. It is estimated that this arrangement resulted in a saving of two months on the overall project.

Jan 1, 1983

By A. M. Croll

The efforts to mechanize narrow reef tabular orebodies unique to this country, are not new. They began in the early 1900s and have over the last century seen varied rates of progress and success. Efforts to mechanize with the use of scraper winches can be regarded as a success. The scraper winch replaced the hand lashing of ore and development waste into hoppers. The initiatives by Anglo Gold and the then JCI to implement trackless mining equipment into these environments had limited success but in general were looked upon as a failure?at least this is the perception. The Chamber of Mines Research Organization (COMRO) in conjunction with various mining houses tried to make a success of the impact ripper. Diamond wire cutting of the stope face is another, which has been tried and tested. The use of high-pressure water to cut rock has also been trialed. These attempts, amongst others, are just a few of the efforts that have not been successful in the quest to make life at the face safer, more productive and easier for our employees. Against the backdrop of an emerging South Africa, the associated high expectations of historically disadvantaged people within the country, a strong rand, demands for better safety, lower cost of production and more efficient operations, mechanization has the chance to make a difference to Anglo Platinum?s business. Mechanization has certainly changed the way other commodities such as coal, base metals and diamonds are won from the earth. Mining?s image is still one of people crawling around in stopes?a dirty, ?low-tech? business. Anglo Platinum?s latest journey to mechanize its underground operations began in earnest in1998 and has enjoyed some successes and failures. The opportunity to change the way mining is done within the company is there. Technologies are evolving, and the implementation of mechanization can certainly assist with the achievement of the goals referred to above. When mechanization commenced, targets were set for the company to achieve but these have been revised in the light of recent events relating to the strengthening rand and a slow-down in expansion plans. However, the intent to mechanize appropriately in Anglo Platinum still exists.

Jan 1, 2004

By P. Saayman

The mining industry has much potential for automation. A great deal of work has been done on this subject and is still ongoing. With automation comes the possibility for optimization, because more information is available and actions can be repeated with more accuracy. This paper looks at possible solutions to the problem of optimizing the autonomous vehicle dispatch system in an underground mine. Possible optimization strategies are evaluated using a simulated environment. The majority of the results indicate that improvements on current methods are possible. Keywords: mining automation, simulation, vehicles, dispatching strategy, optimization.

Jan 1, 2006

This Spotlight gives a brief summary of the proposed 1991 tax amendments of relevance to mines and mining houses. It should be read together with the author's article South African mining tax in the 1990's', which appeared in the August 1990 issue of this Journal. A number of tax amendments of relevance to the mining industry were proposed by the Minister of Finance in his March 1991 budget speech. In addition, certain other measures that may be implemented were set out in the budget review document released at the same time. A word of caution is necessary: these measures will become law only if and when they are enacted in the appropriate legislation. When this legislation is tabled in June, it may not contain all of the measures discussed below, some of the measures may appear in modified form, and other measures not discussed at the time of the budget may well appear. Unless otherwise stated, the 1991 tax amendments will affect companies with years of assessment ending in the twelve-month period to 31st March, 1992.

Jan 1, 1991

Foamed cement packs offer a viable alternative to conventional timber or other forms of packs for permanent underground support. These packs comprise steel mesh and hoop containment with an outer bag for the grout; woven, laminated polypropylene fabric being ideal for the purpose. The grout is supplied in 25kg bags and fed into a purpose ? designed foam placer machine which delivers the foamed grout directly to the packs from 60 metre long delivery hose. Foamed cement grout as a fill material offers attractive properties for support packs, in summary these are: Variable Grout Strength Grout strength is controlled by the grout density being delivered from the placer machine. This can be changed by the machine settings. Strength Development Fast rate of strength development is possible so that support is available quickly. Pack yield The foamed grouts are compressible so that yielding of the grout pack can be achieved without loss of support. Rate of Filling Three sizes of placer machine are available, these use one, two, or three 25kg bags per minute of grout, pack filling time is therefore a matter of minutes, a typical 0.75m diameter pack x 1.2m high taking some 17 minutes to fill. Tests in a 1000 tonne press have confirmed that the above characteristics can be achieved with foamed cement packs at acceptable cost. This will be illustrated in the paper with experience to date.

Jan 1, 2008

By M. Z. Naghadehi, E. Emami, J. Sattarvand, R. Battulwar

In this paper, a methodology for a computerised recognition of joint sets on 3D point cloud models of rock masses is presented. The process starts with classifying joints on a 3D rock mass surface through training a deep network architecture and validated using manually labeled datasets. Then, individual joint surfaces are identified using the Density-Based Scan with Noise (DBSCAN) clustering algorithm. Subsequently, the orientations of the identified joint surfaces are computed by fitting least-square planes using the Random Sample Consensus (RANSAC). Finally, the joint planes are classified into different joint sets, and the dip direction and dip angle for each set are calculated. The performance of the proposed methodology has been evaluated using a case study. The results show that the presented procedure is fast, accurate, and robust.

Sep 1, 2021

By M. S. Shishvan, J. R. van Duijvenbode

The results of dig limit delineation in open pit mining are never truly optimized due to gaps in the underlying data, such as insufficient sampling. Aside from the data uncertainty, there is also an influence on the final dig limit by either humans or by the heuristic character of an optimization method like simulated annealing. Several dig limit optimizers have been published, which can replace the manual dig-limits designing process. However, these dig limit designs are generally not adapted to account for this heuristic character. In this paper we present a stochastic analysis tool that can be used with the results of heuristic dig-limit optimization to increase confidence in the obtained results. First, an enhanced simulated annealing algorithm for dig limit optimization is presented. Then, this algorithm is tested on ten different blasts at the Marigold mine, Nevada, USA, as a case study. Finally, the results are analysed with a destination-based ensemble probability map and an analysis conducted of the final solution data distribution. The generated dig-limit designs of the algorithm include high revenue areas that are excluded in comparable manual designs and show improved objective and revenue values. The analysis tool provides block destination probabilities and box plots with the distribution of opportunity value for the dig limit. Furthermore, with the analysis tool, it is possible to make well-informed design decisions in areas of uncertainty.

Dec 13, 2022

By B. Ceki, A. Mabentsela

The BCL furnace is scheduled to restart operations after being placed on care and maintenance in 2016 due to depressed nickel prices. The decision to start operations after such a stoppage ought to be led by a techno-economic evaluation of process options to make operations more resilient. For BCL, the decision lies between using the existing flash-smelting furnace (FSF) or a top-submerged lance (TSL) furnace. Available studies show that the FSF combined with other converting technologies is cheaper to operate; however, such studies are based on flowsheet simulation results of single copper concentrates and therefore do not provide a full scope of practical capabilities based on smelter operator skills. Using a t-test on normalized prior operational data from three Cu FSF and two Cu TSL, it was found that the only statistical differences between the operating costs of the FSF and TSL technologies are in the coal use for heating the feed blow and number of rebuilds: the FSF consumes coal to heat the feed blow and the TSL requires 2.4 rebuilds during a course of a single FSF campaign. A summative operating cost comparison over the existing BCL FSF 11-year life shows that BCL can decrease operational costs by some BWP 55.5 million if the operation were to change to the newer TSL technology. The savings derive from reduced coal use, which is normally associated with heating the blow when using the FSF. Despite the TSL carrying added costs of 2.4 rebuilds during a life time of one FSF furnace campaign, the cost associated with the TSL rebuilds of approximately BWP 1.3 million is minimal compared with the overall operational expenditure decrease that BCL will incur on using the TSL technology. In terms of the technology, BCL can have higher Ni–Cu recoveries at lower operational costs by elimination of Ni–Cu losses and eliminating the slag-cleaning furnace by converting to a TSL furnace.

Jul 10, 2024

By A. R. Miller

A fuel cell locomotive incorporates the advantages of its competitors, namely catenary-electric and diesel-electric units, while avoiding their disadvantages. It possesses the environmental benefits, at the vehicle, of an electric locomotive but the higher overall energy efficiency and lower infrastructure costs of a diesel locomotive. The natural fuel for a fuel cell is hydrogen, which can be produced from many renewable sources or via nuclear energy, and thus a hydrogen-fuel cell locomotive will not depend on imported oil. Hydrogen produced from renewable primary energies or nuclear energy would provide a totally zero-emissions vehicle, that is, with zero carbon in the energy cycle. A project partnership among Vehicle Projects Inc of the USA, and South African partners Anglo American Platinum, Ltd, Trident South Africa, and Battery Electric, has designed and is launching a series of five prototype fuel cell-powered mine locomotives.

Jan 1, 2012

By Y. Chen, D. He, J. H. Potgieter

The demand for rare earth elements (REE) is increasing rapidly owing to the emergence of new cleanenergy and defense-related technologies. China’s dominates the world production of REE. In this paper, we review the ore characteristics of four typical REE deposits in China and discuss the conventional beneficiation techniques, including gravity and magnetic separation, flotation, and hydrometallurgical processing of these ores. Some of the latest laboratory findings and industrial applications, as well as the development of novel reagents for REE processing in China are presented. The REE beneficiation technologies developed and employed in China could constitute a good case study for many other emerging projects being explored around the world.

Mar 2, 2022

By J. J. Botha

As a Demand Side Management (DSM) Project, money was granted for the procurement and installation of a 3-Chamber Pipe Feeder System (3-CPFS) at AngloGold Ashanti?s Moab Khotsong Mine in the Vaal River Area, Orkney. The first submission was done to ESKOM in December 2002 and the contract was signed in September 2006 at a cost of R 57-million with an envisaged reduction in power of 7 Megawatt per month based on a 90% utilization factor. The project was finally commissioned in December 2008. The technology is not new, but the intent of the paper is to share with others the experience gained by using the technology in a deep-level mine in order to reduce overall power consumption.

Jan 1, 2009

By I. Cerny, M. Vanek, J. Hubácek

"SWOT analyses and the closely related TOWS matrix are frequent starting points for an organization to develop its strategy. The paper deals with the evaluation of the TOWS matrix and presents three novel approaches to evaluate the different factors of the TOWS matrix, namely (1) approach to evaluate the factors with identical weights; (2) approach to evaluate factors with their weights determined within the different quadrants of the TOWS matrix; and (3) approach to evaluate factors with weights determined within the whole TOWS matrix. The third approach has two variants. The proposed approaches to evaluate the TOWS matrix were tested on a SWOT analysis of a significant mining company in the Czech Republic. The results imply that the strategy W-T (weaknesses-threats) is recommended in three cases, while the strategy S-T (strengths-threats) is recommended once. The paper may be valuable for managers responsible for strategic planning.IntroductionThe process of human needs gratification has been closely connected with raw material resources of the planet. In the contemporary socio-economic conditions, the task of the mining company managers, apart from extracting mineral resources, is to meet the owners' intents.The managerial work itself becomes very complex. In mining companies in particular, the complexity is augmented by the characteristics of the business. Undoubtedly, the key factor is that mineral resources cannot be renewed or relocated. Stojanovi (2013) characterizes mining projects as involving great investments in finance and time, as well as consecutive decisions and a 'complex mosaic of numerous unknown factors that affect the value of the project'. He adds that mining projects are typified by a 'number of geological, technological, technical, economic, environmental, social, and financial risks' (Stojanovi , 2013).Inter alia, the managerial work may also be intese due to the dynamic internal and external conditions for the existence of any company (Vane? k, 2014). This tallies with Peter Drucker’s prediction in 1969; that the times at the turn of the millennium could be expected to be turbulent (Drucker, 1969)."

Dec 1, 2018

By Y. Rajpal

The Hedley and Grant pillar strength formula is widely used within the South African mining industry to calculate pillar strengths in bord and pillar mining layouts, and is currently being used at Bathopele Mine. Bathopele is an operation of Anglo American Platinum near Rustenburg, mining the UG2 reef at depths ranging from 40 m to 300 m below surface. The formula includes a parameter K, which is a downrated uniaxial compressive strength value of the rock, used to calculate the strength of a pillar. At Bathopele Mine, for the shallower areas Less than 150 m the value was 33 MPa, but this was increased to 44 MPa due to the fact that rock mass conditions improved and there were no incidence of failure in the shallower areas. Underground observations showed pillars to be stable with no signs of failure, and it was questioned whether the design was not still too conservative, resulting in sub-optimal extraction ratios and consequently a loss of revenue to the mine. A trial mining section was started at the mine where the pillars were reduced from 6 m x 6 m to 5 m x 5 m and the pillar behaviour was monitored for the onset of failure. Numerical modelling was conducted using the TEXAN code to back-analyse pillar stresses in order to find a more realistic value for K. Results from the trial section indicated that the pillar design was in fact too conservative, and the value for K was adjusted to 54 MPa for future designs. This paper details the findings from underground monitoring and numerical modelling results, and includes details for further calibration of the K value in order to further optimize the extraction of the orebody.

Jan 1, 2012

By Y. Fu, C. Aldrich

This study investigates the use of dense convolutional neural networks to estimate bubble size distributions in flotation froths. 20 videographically captured images of froths from an industrial platinum flotation plant in South Africa were labelled semantically with an image annotation tool, LabelMe (https://github.com/wkentaro/labelme). As a result, pixels in the images could be categorized into three classes, namely ‘bubbles’ (class 0), ‘bubble boundaries’ (class 1) and ‘background’ (class 2). A U-net architecture with a ResNet34 backbone was trained to segment the images via classification of the pixels in the images. 5 of the 20 images were used to validate the performance of the neural network. Explicit inclusion of the bubble boundaries as a class proved to be significantly more effective than training the network with two classes only (i.e. bubbles and background). However, the thickness of the boundary layer regions were critical. If too thin, it was difficult to distinguish between some contiguous bubbles and if too thick, some fine bubbles may not be identified. The results were promising, although there is still significant scope for improvement, among other by making use of more images for training and validation. Keywords: Flotation Froths, Convolutional Neural Networks, Deep Learning, Bubble size Analysis

Jan 1, 2020

By R. L. Attridge

Namibia's newest mining enterprise, the Navachab Gold Mine, was officially opened by President Sam Nujomo during June 1990. The mine is a joint venture between Erongo Mining & Exploration Company Limited, Metal Mining Corporation of Canada, and Rand Mines Windhoek (Pty) Ltd. Erongo has a 70 per cent interest in the mine, while Metal Mining and Rand Mines hold 20 per cent and 10 per cent respectively. Anglo American Corporation and its associates hold two-thirds of Erongo shares and CDM (Pty) Ltd one-third. The Mine is managed by Erongo Mining & Exploration Company. The property is located some 10 km southwest of the town of Karibib and 170 km west-northwest of the Namibian capital of Windhoek (Fig. 1), the name of the Mine being taken from the farm on which the gold deposits were discovered. Navachab is an opencast operation and was brought into production in December 1989 at a cost of around R84 milion-RS,2 million under budget. The plant is designed to treat 840 kt annually at an average gold grade of 2,6 g/t. This wil produce 1900 kg of gold per year, which at today's prices will earn Namibia more than R60 million in foreign exchange.

Jan 1, 1991

By A. Whillier

Note: Hydraulic rock drills and their effect on the underground environment by A. WHILLIER, Pr. Eng Se. D., (M.tT.) (Fellow) In any situation where hydraulic rockdrills are used underground, it is evident that an amount of heat equivalent to the total electric input to the power pack would enter the ventilation air. Book review Australian Mineral Industry 1972 Review. Australia, Department of Minerals and Energy. NIM report Report no. 1691 The determination of zirconium and aluminium by 14MeV neutronactivation analysis. Automation in Mining, Mineral, and Metal Processing The International Federation of Automatic Control (IF AC) is to hold its second symposium on the above subject in Johannesburg on 13th to 17th September, 1976. V Simposio de Mineracao A symposium is being arranged for 6th to 9th August, 1975, in Ouro Preto, Brazil. ACHEMA 1976 The 18th Chcmical Engineering Exhibition-Congress and European Meeting of Chemical Engineering will be held in Frankfurt from 20th to 26th June, 1976, and thc Chemical Engineering World Congress Sixth Underwater Mining Institute The above Institute will be held on the main campus of the University of Wisconsin in Madison, U.S.A., on 2nd and 3rd October, 1975.

Jan 4, 1975

By M. Steyn

This article captures the intrinsic differences of thermal coal products, their utilization and their substitution characteristics. South Africa produces approximately 245 million tonnes of coal annually. Eskom consumes 46% (approximately 112 million tonnes), 26% (approximately 65 million tonnes) is exported, and SASOL Synthetic Fuels consumes 18% (approximately 44 million tonnes) and a further 9% (approximately 22 million tonnes) is consumed by domestic users in various different industries. Marketing theory contributes significantly to understanding the importance of technical product and quality appreciation and comprehension, encompassing elements of price, distribution, and promotion. Coal product specification is determined by the inherent geology of a resource and the number of complex actions to market the product to a specific consuming market. Sampling, analyses, beneficiation application, and an array of parameters contribute to matching thermal coal products to the value-in-use it provides to the different markets and its consuming industries. Coal producer shave come under increased scrutiny since South Africa has been experiencing electricity shortages since early 2008. General misunderstandings were declared on public forums and in the media by both legislators and the South African public since a perception developed that South African coal producers are exporting coal that could be utilized by Eskom.

Jan 1, 2010

Introducing your Council. Mr J. S. Freer, Pr. Eng., after matriculating at Michaelhouse in 1944, obtained a B.8c. degree in chemistry and biology (1948) and a B.Sc. (Hons.) in chemistry (1949) from the University of the Witwatersrand. Mr G. C. Thompson matriculated at Dale College in 1951. He then attended the University of the Witwatersrand, where he obtained a B.8c. (Min. Eng.) in 1959. Mr P. T. Fewell was born and educated in the United Kingdom. After obtaining the degree of Bachelor of Engineering (Mining) in 1958 at Sheffield University, he emigrated to South Africa. DtP. R. Jochens, Pr. Eng., has been a member of Council since 1974, serving as President in 1980-1981.

Jan 1, 1984

"The management of outlier grades in positively skewed gold distributions is a contentious issue. Incorporating outliers in standard ordinary kriging (OK) estimation procedures in a way that honours the data without smearing extreme grades into surrounding areas has been problematic. Cutting or capping of outliers to mitigate their influence in estimation techniques is common practice, while methods that manipulate the OK system of equations fail to honour the data. We propose a method of post-processing of kriging weights that provides realistic OK estimates and mitigates smearing without manipulating kriging equations or changing the original grades. The method requires that the data is not clustered, is approximately equally spaced, and is of the same support. Positively skewed data is ordered on attribute grade and nonlinearly transformed to a Gaussian histogram of categorical bins whose frequency is based on their likelihood of occurrence and location in the sample distributions. Factors that restrict kriging weights are calculated by dividing the percentage frequency of data in each bin by the percentage frequency of data in the bin with the highest frequency. Restriction factors applied to the kriging weights in the OK estimation restrict the range of influence in proportion to their probability of occurrence in the distribution. Smear reduction post-processing is easy to implement and addresses issues arising from negative kriging weights while considering the spatial location of samples, the sample grades, and their probability of occurrence. The method mitigates both smoothing and conditional bias.IntroductionOutliers are sample observations that deviate considerably from the standard or expected (Hawkins, 1980). These deviations can be high or low in grade depending on the distribution. The presence of outliers in a mine sampling campaign could provoke mixed reactions. Mining engineers might view high-grade outliers as a promise of achieving higher grades, while the geostatisticians view outliers as affecting the accuracy and precision of the overall estimate, among other issues. Having identified outliers, the geostatistician must decide how to account for their presence and treat them so that true underlying estimates are not distorted. Advanced knowledge of the deposit allows the geostatistician to identify and treat outliers acceptably, especially where samples are limited in number and the true grade distribution is uncertain. If ignored, or treated incorrectly, outliers are likely to lead to smearing of extreme grades into the surrounding estimates, thereby steering regions towards potential under- or over-estimation."

Apr 1, 2019