Search Documents

By X. H. Li, Q. Zhang, X. Fei

Bauxite residue known as red mud (RM) is a by-product produced in massive quantities during alumina production by the Bayer process with a utilisation rate of less than 5%. A large amount of RM accumulated and produced continuously has had a seriously adverse impact on the surrounding ecological environment. The application of RM in building materials is considered to be the most effective and thorough way to make RM harmless and recycle resources for the reason that adding RM to concrete as a mineral admixture could not only consume a lot of RM, but also save cement and other energy-consuming industrial products. In this paper, the adaptability to cement and aggregate of RM was studied. The results showed that the compressive strength and flexural strength of concrete using ordinary Portland cement, slag Portland cement or fly ash Portland cement as cementing material showed different trends with the increase of the amount of RM. The influence rules of RM on the compressive strength of Portland cement, slag Portland cement and fly ash Portland cement concrete were similar, whether for silicate aggregate or carbonate aggregate. RM has a negative correlation to the flexural strength of silicate aggregate-ordinary Portland cement concrete, but a positive correlation to silicate aggregate-slag Portland cement, silicate aggregate-fly ash Portland Cement. RM promoted the formation of calcium carbonate crystals and inhibited the formation of ettringite and calcium hydroxide crystals in the matrix while ordinary Portland cement, Portland cement and fly ash Portland cement were used as cementing materials. This study provided support for the use of RM in concrete, the reduction of solid waste storage, and the saving of high energy consumption cement as well. Keywords: Red mud, cement, aggregate, adaptability, mechanical properties, mineral composition

Jan 1, 2020

By E. M. Bloomfield, C. A. Jermy

Geotechnical tests were carried out within an area of the coastal sand dune cordon of northern KwaZulu-Natal which is currently being exploited through mining of heavy mineral sands. In situ and laboratory tests were carried out to assess the density, strength and stability of the dune sand material before and after mining. The most stable combination of sand (>63µm) and fines(<63µm) material was determined as well as the effects of compaction on the strength and permeability of the sand dune samples. In situ DCP and density tests showed that the sand dunes fall in density immediately after mining has taken place. However, settlement of the dunes occurs with time and the density increases within the top 2 metres, and particularly once the dunes become re-vegetated. Laboratory tests carried out showed that the dune sand with between 20% and 30% added fines had the highest shear strength and dry density, but the permeability was shown to decrease steadily with increasing fines up to 40% fines added. The addition of fines would result in steadily increasing water flow problems. Compaction of the dune sands was shown to significantly increase the density and the shear strength, but with a corresponding dramatic decrease in the permeability of the material. Slope stability analysis carried out on models of the dunes with increasing fines showed that the addition of fines increases the stability of the dune sands up to a peak of about 30% fines added, and compaction further increases the stability of the dune sands. Despite the benefits of compaction on the stability of the tailings dunes, the loss of permeability is thought to outweigh the benefits as well as the high costs involved. The stability of the tailings dunes greatly increases after re-vegetation. Compaction and densification of the tailings dunes may be necessary within the top 2 m interval if large-scale construction takes place on the sand dunes. Petrographic analysis was performed to understand the granular interactions of the sand and fines fractions, and the effect of the in situ weathering of the dune sands on the stability of the sand dunes. As the fines contents increase the gaps between the sand grains are filled, until a point where the percentage of fines begins to push the sand grains apart.

Jan 1, 2003

By A. Peake

Background The CSIR Division of Mining Technology assumed responsibility for the operations of the Hoist Rope and Mechanical Test Laboratories at Cottesloe in April 1999. The laboratories were previously the responsibility of the CSIR’s Division of Manufacturing and Materials Technology, before which they fell under the National Mechanical Engineering Research Institute (also of CSIR). As the focus of this conference is on safety in mines research institutes, it was thought appropriate that this paper should review some of the activities at Cottesloe and its role in supporting mine safety strategies.

Jan 1, 2003

By B. Maybee, J. Venter, J. Wesseloo

The selection of open-pit slope angles involves high-value decisions with small changes in slope angle, often representing significant changes in net present value. The existing methods used to define design acceptance criteria have evolved from factor of safety to probability of failure (P[F]) to risk consequence to risk frontiers, which represents current state of the art. Current design acceptance measures are based on references to published tables representing the experience and judgement of their authors, who did not specify the purpose of the measures contained therein. As the purpose of the published design acceptance criteria is not specified (i.e., definite stability, marginal stability, optimization, etc.), such tables cannot be used to achieve optimum slope angles that maximize profitability. This paper develops a design acceptance criterion that maximizes profitability by defining a formulation for optimum risk that balances expected risk and reward. The model developed is titled the Mining Risk Model (MRM), and is applied to open-pit slope angle selection through an equation for optimum probability of downside (P[D]O) that balances the upside or opportunity, the P[F], and the downside impact. This formulation for optimum risk is unique, as many authors have presented objective functions for their risk models that can be optimized, but none of the sources reviewed contained a formulation for optimum risk. The MRM is sufficiently flexible to allow the design performance measure that drives P[F], and hence P[D]O, to be selected based on the intended goal. Furthermore, the essential information that must be known to quantify optimum risk is defined. This allows users to determine what information to collect for optimum risk decisions. A further benefit of the MRM is that slope angle decisions and pit shells can be ranked to select the best option, and a threshold is provided that separates acceptable from unacceptable decisions. Finally, the workflow and information required to determine optimum risk are presented.

Sep 9, 2024

By X. B. Zhao, J. G. Cai

When stress wave propagates through fractured rock masses, the wave will be slowed and attenuated due to the presence of these fractures. If the amplitude of stress wave is large enough to mobilize nonlinear deformation of these fractures, they will present different effects on one-dimensional P-wave propagation compared with those of linear deformational fractures. The static BB model is adopted to describe the nonlinear deformational behavior. Method of characteristics combined with displacement discontinuity theory is used to build analytical solutions of wave particle velocities and wave stresses. These equations are numerically solved with sufficient accuracy.

Jan 1, 2003

By A. Dienenthal

"The casthouse floor has always been one of the most dangerous working places on a blast furnace or a ferro-alloy/nonferrous furnace. Apart from working in an atmosphere including toxic gases, fumes, and dust, the workers have to perform hard and heavy manual work close to runners and ladles filled with hot liquid metal and slag.Before the invention and installation of tapping equipment the tap-holes were opened and closed manually. Opening was done by means of steel bars and sledgehammers, whereas the tap-hole was closed by repeatedly ramming small amounts of clay or refractory material into the tap-hole, again with the help of long, heavy bars. In addition, on blast furnaces the blast had to be stopped, since it was impossible to close the tap-hole properly against the blast furnace pressure. This stoppage of the blast resulted in regular losses of production. Around 1900 a major change in technology occurred. Samuel W. Vaughen, superintendent of the blast furnace department of the Cambria Iron company at Johnstown, Pennsylvania (USA), invented the first clay gun in 1895 (Wiley, 1896) (Figure 1)."

Jan 1, 2014

By P. He

Abstract This paper introduces tested results of rock-socketed pile in Nanjing, Wuhan and Chongqing. From a force- transfer model, a distribution of axial force for pile-body and inlaid resistance for rock-socketed pile was deduced. Comparing the results of test and calculation, it shows that the calculation result coincide with the test result. Keywords rock-socketed pile, load transfer, inlaid resistance, end resistance. Zusammenfassung: dieser text legt eine kuyze Einfuehyung ueber die Erfolge wissenschaftlicher Forschungsarbeit in bezug auf die Grundprinzipien der Mechanik von Belastungsuebermittlung der Einlegesteinpfeilers der Durch Benutzung von Ausgleich/Balance der inneren Kraft und Deformationskoordinierung wird das mechanische Modell der Belastungsuebermittlung des Einlegesteinpfeilers aufgestellt. Vom lebendigen Beispiel wird dia Wellenkraft des Steinpfeilera und die Verteilungskurve Einlegebfestigungskraft ausgelegt, man hat diess bereits mit der tatsaechlichen genessenen Kurve verglichen. Schluesselwoerter: Einlegesteinpfeilers, Belastungsuebermittlung, Einlegebfestigungskraft, Seitenwiderstand. Résumé - Le présent article décrit de façon succincte des résultats de la recherche sur le mécanisme du transfert de chargement du pieu d’ancrage au massif. Une modèle dynamique du transfert de chargement du pieu d’ancrage au massif est ainsi établie avec l’application des conditions de l’équilibre de contraintes internes et de coordination de la déformation. L’expérimentation sur des exemples réels a permis de mettre à jour des courbes de distribution de la force axiale du corps du pieu et de la force d’ancrage avec comparaison aux courbes effectivement mesurées in situ. Mots clés - Pieu d’ancrage au massif, Transfert de chargement, Force d’ancrage, Résistance à la pointe

Jan 1, 2003

By C. W. P. Finn

INFACON is of special significance to people in South Africa who are interested in ferro-alloys, because it was in South Africa that the idea of regular international congresses on ferro-alloys was conceived and developed. INFACON 74, the first-ever such congress, was held in Johannesburg from 22nd to 26th April, 1974, being organized by the South African Institute of Mining and Metallurgy, the National Institute for Metallurgy, and the Ferro Alloy Producers&apos; Association of South Africa. Design Awards The Design Institute is inviting entries for the 1981 Shell Design Awards. Any product that falls into the three categories shown below, and that was designed in South Africa and is in production, is eligible for an award. Since their inception in 1970, the Shell Design Awards

Jan 1, 1981

By R. Strydom, J. H. Selby, J. Slabbert, W. Enslin

Zircon is a naturally occurring silicate of zirconium, which is used in large quantities (~1 million tonnes per annum) for its refractory properties and its extreme chemical inertness. All zircons contain uranium and thorium bound into the crystal lattice, generally at levels up to 500 ppm of uranium plus thorium. This paper focuses on one aspect of the zircon industry—the ability to safely transport large quantities of zircon sand. Currently zircon is not classified as a radioactive material for transport purposes. However, this is because of a factor used in the exemption clauses of the IAEA code on safe transport of radioactive materials. The objective of this study was to determine the validity of this factor, and was submitted as part of an IAEA Coordinated Research Project (CRP). The study is based primarily on measured rather than modelled data and covers the transport of large quantities of zircon from producers in South Africa to customers in Europe. Both occupational exposure of workers and exposure of members of the public have been considered. The transport routes studied cover rail, road, ocean-going ship and inland barge transport of unpackaged bulk products. The study showed that the most exposed member of the public would receive 10µSv/annum,while the most exposed worker would receive 144µSv/annum of exposure. It is concluded that these levels are well below all regulatory limits for such activities involving naturally occurring materials. The study also showed that normal operational exposures are higher than those in accident scenarios, a feature which does not occur with higher activity materials. It is further concluded that the study validates the use of the factor of 10 in TS-R-1, as applied to zircon sand. Additionally it is also concluded that the exemption currently applied to the transportation of bulk zircon sand is valid.

Jan 1, 2003

By B. R. Broekman, D. W. Penman

Discussion by P.J Lloydt Broekman and Penman describe (J.S. Afr. Inst. Min. Metal., vol. 91, Aug. 1991, p. 261) the addition of sodium cyanide and zinc sulphate to the flotation feed at Prieska. They note that for &apos;safety sake, lime was added to the rod mil to raise the pH to 9,5&apos;, and that &apos;personnel working in the vicinity of the rod mil were required to wear gas masks&apos;. Author reply to P.J. Lloyd We thank Dr Lloyd for his interesting contribution. As he correctly points out, the Prieska float had run with cyanide solutions at pH values of 6,4. In fact, it ran safely for extended period with the pH slightly below 6.

Jan 1, 1991

By J. Galloway, P. K. Hofmeyr

Obviously all mining operations require much analytical work to be carried out. This starts with exploration, becomes more stringent with the evaluation of a mineralised area and finally becomes on-going when mining operations are under way. All these phases are carried out by geologists, metallurgists and mining engineers. They require analyses to carry out their functions but usually have no involvement in the analyses themselves. Analyses are carried out at commercial laboratories or in-house analytical laboratories. In the past in South Africa the tendency was for the larger mining houses to have their own centralised laboratories for exploration samples with each mine having it?s own laboratory to meet only that mine?s requirements. The centralised laboratory maintains QC functions at the subsidiary laboratories. In other mining areas of the world there has been a strong tendency for all geological analytical requirements, especially for exploration and mining, to be carried out at commercial analytical laboratories. In recent years there has been a tendency for mines in South Africa to move in the same direction. This paper discusses the factors that need to be taken into consideration when a new laboratory is being planned and automation is an option. The planning of the laboratory at the new Langer Heinrich Uranium mine in Namibia is discussed considering these factors. 2.0 REQUIREMENTS OF A MINING ANALYTICAL LABORATORY The purpose and requirements of a mining analytical laboratory are fairly obvious and can be summarised as follows :- 1. All mining operations must have access to analytical facilities, either in-house or commercial 2. The laboratory must be able to handle all the sample types submitted by the mining operation These can be mining, exploration and/or plant samples. They can comprise solids (rocks, bore-cores), slurries and/or liquids.

Jan 1, 2007

The paper discusses the improvements achieved after an external sparger flotation column was installed as a final cleaner at the Northam Platinum Ltd. UG 2 concentrator in South Africa. It further discusses the improvements achieved after the conversion of a conventional flotation column, utilized as cleaner in the Merensky concentrator, to an external sparger flotation column. Finally, the application of the above knowledge in the design and commissioning of an external sparger flotation column as final cleaner in the furnace slag concentrator, is also discussed. 1. FINAL CLEANER AT THE UG 2 CONCENTRATOR The MF2 designed UG 2 concentrator is processing 75 000 tonnes run of mine ore at a head grade of 4.0 g/t 3PGM+Au and a feed Cr2O3 concentration of 28 %. Since commissioning of the plant in 2001, Cr2O3 in final concentrate amounted to approximately 5 % of the total mass. Although final concentrate produced from the UG 2 concentrator is blended with final concentrate obtained from the Merensky concentrator before smelting, blended Cr2O3 values in excess of 1.6% lead to difficulties in the subsequent smelting process. Several options for reducing the amount of Cr2O3 in final concentrate have been evaluated namely:- ? Differing types of depressants at various dosing rates. This test work did not reduce the amount of Cr2O3 reporting to final concentrate by any significant extent. ? Reduction in mass pull to minimize the entrainment of Cr2O3 in the concentrate stream.. This process change had a detrimental effect on PGM recovery. Conclusions were drawn that conventional mechanically agitated flotation cells could not achieve the required selectivity without sacrificing PGM recovery. As a consequence an alternative mechanism needed to be incorporated for the final cleaning of PGM concentrate.

Jan 1, 2007

By P. N. Erasmus, M. Heyns, M. J. Pretorius

The characteristic of stope supports plays a vital role in the design of the supports. This paper deals with the characterisation of both cellular lightweight concrete and timber supports since both supports absorb and dissipate the energy in different ways. The behaviour of the support and hence its performance is simulated for different loading conditions by constructing a model consisting of various mechanical components like springs, dampers and blow-off valves. When the force exerted by the stope support increases significantly during deformation of the support, the stresses in the hangingwall could exceed values where failure of the hangingwall may occur. There is a need to understand this phenomena and the work presented in this paper is a first attempt to start with the characterisation of the stope support. Les caractéristiques des supports de taille jouent un rôle vital dans la conception des supports. L’étude présente traite de la caractérisation des supports cellulaires en béton léger et en bois, puisque ces deux types absorbent et dissipent l’énergie de façons différentes. Le comportement du support et par conséquent sa performance est simulée pour des conditions différentes de chargement en construisant un modèle qui consiste en des organes mécaniques variés tels que ressorts, registres et valves d’échappement. Quand la force exercée par le support de taille augmente considérablement pendant la déformation du support, les contraintes dans le toit peuvent dépasser des valeurs qui pourraient entraîner la défaillance du toit. Il est nécessaire de comprendre ce phénomène et l’étude ici présentée constitue un premier essai dans la caractérisation du support de taille. Die Charakteristika der Strossenunterstützung spielt im Design von Unterstützungen eine vitale Rolle. Diese Arbeit befaßt sich mit der Charaketerisierung sowohl der porösen Leichtgewichtbeton- als auch mit der Holzunterstützung, da beide Unterstützungen Energien auf verschiedene Art und Weise absorbieren und auflösen. Das Verhalten der Unterstützung und folglich seine Leistung wird für unterschiedliche Ladezustände simuliert, indem ein Model konstruiert wird, welches verschiedene mechanische Komponenten wie Federn, Dämpfer und Ausblaseventile enthält. Wenn die von Strossenunterstützung während einer Unterstützungsdeformation aufgebotene Kraft signifikant ansteigt, könnten die Spannungen im Bereiche des Stollenfirstes Werte überschreiten wo ein Versagen des Stollenfirstes eintreten kann. Es besteht die Notwendigkeit dieses Phänomen zu verstehen, und die Arbeit, die in diesem Elaborat dargestellt wird, ist ein erster Versuch, mit der Charaketerisierung der Strossenunterstützung zu beginnen.

Jan 1, 2003

By S. L. Bell

Most Australian longwall coal mines are currently working coal faces up to nine kilometres from the surface. In the event of a mine emergency walking this sort of distance wearing breathing apparatus becomes very difficult if not impossible. Self-rescue continues to remain the focus of mines rescue in Australian coal mines and this paper describes a vehicle modification which will improve the chances of a miner rescuing himself. Existing mine personnel transport vehicles are not designed to operate in some types of atmospheres that may be present following a mine fire or explosion event. An Australian Coal Association Research program (ACARP) funded research project recently completed in Australia has developed a specification for a vehicle that is able to operate safely in some types of post emergency atmospheres. During the course of this investigation, diesel and electric vehicles were examined prior to making a final decision on vehicle suitability. Based on the fact that there are already some 1500 diesel vehicles in use in underground coal mines in Australia it was decided that modifications to existing diesel engines would be the best option. This presentation will outline the proposed specification for the vehicle and the reasons behind the decisions that were made with respect to the specification.

Jan 1, 2003

By Jannie Maree, Dieks Theron, Ryneth Nengovhela, Patrick Hlabela

In extracting base metals from ore bodies, sulphide as well as oxide, the main environmental concern is sulphur, whether in the form of sulphurous gases or sulphate in liquid form. Generally sulphur is in over supply in developed countries mainly because of strict legislation to capture it. In developing countries on the other hand there is usually a shortage of sulphur because of less strict environmental legislation. Africa falls in this second category and the African continent imports substantial amounts of sulphur despite the fact that large quantities of sulphur is emitted by smelters, thermal power stations, coal mines, fertilizer manufacturers and others. Other than making acid from gaseous emissions, existing methods to capture sulphur from gaseous and liquid effluents are uneconomical and it ends up in the environment either as ammonium sulphate (from gaseous effluents) or as gypsum (from liquid effluents). The CSIR?s Environmentek and Pyroserv has developed a process whereby gaseous sulphur emissions and sulphates in liquid effluents can be economically captured and converted into elemental sulphur and metal carbonates. The elemental sulphur is of high purity as it is precipitated from a gas stream and is readily marketable. The metal carbonates (barium or calcium) can be recycled back to the process or marketed. The only harmful byproduct of the process is carbon dioxide. Should natural gas or methane be available the carbon dioxide could be reduced by about one third. Should solar, wind or hydro energy be available to generate hydrogen the carbon dioxide emissions would be zero. Employing this technology could make Africa independent of sulphur imports and furthermore reduce the impact of acid rain and seepage of sulfate from gypsum and other waste dumps into the environment.

Jan 1, 2005

By X. M. Prévost

The reassessment of coal reserves has become a matter of urgency and has come as a result of the present situation of the industry, in the context of globalized coal economies, as well as new mining legislation and the advantages and difficulties of domestic coal suppliers. The de Jager report concerning coal reserves, released twenty years ago, can no longer be used as an estimate for accurately forecasting South Africa’s future coal production. The new reserve and resource study will promote the diversification of energy sources and provide a clearer view of the future of coal mining in the country. With plans to increase South Africa’s coal export capacity to approximately 84 million tons by 2005, it is uncertain whether the country really has sufficient reserves to meet this expansion, as well as satisfy the projected increase in inland demand. The face of South Africa’s coal industry and by association, the economy of our coal-dependent country, are both set to change. This is mainly due to factors such as the demise of most of the large collieries over the last approximately twenty years, growing numbers of economic empowerment producers, the emergence of strong competition in the export market, the dawn of Clean Coal Technologies (CCTs) and the Kyoto Protocol The paper will attempt to dispel some of the current myths about coalfields and reserves and highlight potential areas of high quality coal reserves, available mainly to new entrants in the industry. Keywords: Central Basin, Clean coal technologies, Coal combustion, Coal exports, Coalfields, coalLink, Coal reserves, Coal resources, Coal processing, Colliery, Economic empowerment, Discards, Fluidized bed combustion, Low-ash coal, Metallurgical coal, Power generation, Pulverized fuel, Reserve blocks, Richards Bay Coal Terminal, Run-of-mine production, Saleable production, SAMREC Code, South Dunes Coal Terminal, Steam coal, Synthetic fuels.

Jan 1, 2003

By A. Fahimifar, H. Soroush

Abstract: Triaxial tests were conducted on the schist specimens with various anisotropic angles under confining pressures of 0, 7 and 15 MPa, and axial stress-axial strains, were measured and plotted for various conditions. The results obtained reveal the effects of schistose on the strength and deformability of the rock very clearly. Peak strength of the specimens for 00 and 900 schistose orientations are nearly the same. Modulus of elasticity of this rock varies with anisotropic angle. For 0 orientation modulus of elasticity increases to a maximum. Confining pressure increases the peak strength and improves the rock deformability. However, this effect is not the same for various orientations, and there are no similar trends for each anisotropy direction. Analysis of the results shows that consideration of a linear failure criterion such as Mohr-Coulomb is appropriate for the prediction of rock behaviour up to 10 MPa, rather than a non-linear one. The analysis also reveals that the friction angle and cohesion are affected by the anisotropy orientation, and this effect is more important for the cohesion than the friction angles. Resume: Les esseys triaxiales sur les echantillon d un roch schist avec les differents angles non-isotrop sous les tension lateral zero et sept et qoinze mega pascal (mpa) est fait et les covtraite et allongment unitaire sont mesure et leur curues est destine sous different condition les resultats obtenues montre les effets du schistosite sur le resistance et le ductilite vissiblement. Le resistance final sur les echantilions pour les angles o degre et 90 degree est equivalent. Le modoule d elasticite de ce roch sera difere par a port de l angle de stratification. Pour l angle o degree le valeur de modoule est le maximum. le pousse lateral augmenterai le resitance final, et sera amilterai le toleran le de ductilite. Mais cette effet bn est pas unigue pour les different stratification, et pour les diferents directions no– isotrop it n y a pas le meme solution. L analyse des resulitats montre que le criterre de ruin comme mohr–colomb est moderate pour le pousse lateral jusq av lo mega pascal , et ce n est pas neccesaire d utiliser de criterre no–linear . Cette analyse aussi montre que l angle de frottement et cohsion est en relation de la direction no–isotrop, et cette effet est olus important pour le cohsion par a port de l angle de frottement . Abriß : Dreiachsige Prüfung wurde auf den schist Exemplaren mit verschiedenen anisotropic Winkeln unter Bestätigen von Drücken von 0.7 und 15 MPa geleitet, und axiale Spannung axiale Spannungen, wurden gemessen und für verschiedene Bedingungen wurde geplant. Die Ergebnisse haben die Wirkungen von schisocity auf der Kraft und dem deformability des Felsen sehr deutlich erhalten offenbart. Maximale Kraft der Exemplare für 0° und 90 sind° schistos Orientierungen beinahe das gleiche. Modulus der Elastizität von diesem Felsen ändert sich mit anisotropic Winkel. Für 0° vermehrt Orientierung modulus der Elastizität zu einem Maximum. Einschränkender Druck vermehrt die maximale Kraft und verbessert den Felsen deformability. Aber ist diese Wirkung nicht das gleiche für verschiedene Orientierungen, und es gibt keine ähnlichen Tendenzen für jede anisotropic Richtung. Analyse der Ergebnisse zeigt jener Überlegung Kriterium eines linearen Ausfalls wie zum Beispiel Mohr Coulomb passend für die Voraussage von Felsen Verhalten bis zu 10 MPa, anstatt eines nicht linear ist. Die Analyse offenbart auch, daß der Reibung Winkel und Bindekraft werden beeinflußt von der anisotropic Orientierung, und diese Wirkung wichtiger für die Bindekraft ist, als der Reibung Winkel

Jan 1, 2003

By C. D. Winkler

Vanadium-based sulphuric acid catalyst has been utilized to oxidize SO2 to SO3 since the early 1900s. This versatile product displaced the expensive and easily poisoned platinum-based catalyst in nearly all applications by the 1930s. MECS has been manufacturing the vanadium-based catalyst since 1925 and today is the leading supplier in the world of sulphuric acid catalysts in a variety of forms. Currently, MECS has worldwide customer/technical support for the catalyst as well as a dedicated catalyst manufacturing plant in Martinez, California. MECS also has a strong technical and research and development programme dedicated to creating new and improved products and services. This paper will describe some of the technical details of vanadium-based sulphuric acid catalysts as well as offering a unique look into how caesium-promoted MECS catalysts can be used in single and double absorption acid plants, and off-gas plants running on irregular gas feeds, to reduce emissions and preheater run times. An update on MECS technical services extended for use in characterizing converter performance is also presented.

Jan 1, 2009

By G. R. Addie, A. S. Roudnev

The Hydraulic Institute has completed the task of developing a new ANSI/HI standard 12.1-12.6 (2005) for rotodynamic (centrifugal) slurry pumps covering nomenclature, definitions, applications, and operation. The standard provides examples of the different slurry pump types and contains an extensive section on pump and slurry definitions. The effect of slurry on pump performance is covered along with the pumping of froth. Reference is also made to ANSI/HI standard 9.6.7 (2004), which contains anew method for pump performance correction when handling viscous fluids. Classification of slurry services is established and then is used to determine limitations on velocities and total head per pump in order to obtain acceptable wear performance. The new service class, head per stage and other limits are directly related to capital and other cost considerations that will affect solids transport system economics. The writers review the contents of the new standard, highlight the main points, and discuss the reason for the slurry classification, corresponding limits and expected implications, particularly with respect to operating costs of the pumps in solids transport systems.

Jan 1, 2007

By G. R. Addie

The Hydraulic Institute has completed the task of developing a new ANSI/HI standard 12.1-12.6 (2005) for rotodynamic (centrifugal) slurry pumps covering nomenclature, definitions, applications, and operation. The standard provides examples of the different slurry pump types and contains an extensive section on pump and slurry definitions. The effect of slurry on pump performance is covered along with the pumping of froth. Reference is also made to ANSI/HI standard 9.6.7 (2004), which contains a new method for pump performance correction when handling viscous fluids. Classification of slurry services is established and then is used to determine limitations on velocities and total head per pump in order to obtain acceptable wear performance. The new service class, head per stage and other limits are directly related to capital and other cost considerations that will affect solids transport system economics. The writers review the contents of the new standard, highlight the main points, and discuss the reason for the slurry classification, corresponding limits and expected implications, particularly with respect to operating costs of the pumps in solids transport systems.

Jan 1, 2007