Search Documents

By Andrew A. Cochran

Laboratory-scale research was conducted by the Bureau of Mines to develop a new process for treating electroplating and other wastes. Various acid and alkaline cyanide wastes were combined under controlled conditions to neutralize the wastes and to almost completely precipitate the metals and cyanides. The metals were subsequently recovered for recycling; the cyanides can also be easily recycled. The process was successfully used to treat the major types of electroplating and etching wastes, containing Cd, Cr, Cu, Ni, and Zn, and to treat both concentrated and dilute wastes. The economic aspects of treating concentrated electroplating, etching, and anodizing wastes are especially attractive because of the low cost of mixing two wastes, the high value of the recovered metals, and the simplicity of the recovery procedures. The filtrates from the waste-plus-waste step were relatively harmless compared with the original wastes and met Public Health Service standards for free cyanide content. Free cyanide ions were not detected in most of the filtrates; the limit of detection was 0.03 ppm. Only small amounts of HCN were produced during the neutralization; the HCN was collected and neutralized.

Jan 1, 1974

By E. C. Baker

The Bureau of Mines estimated the economic feasibility of investing in a directional hole methane drainage project in the Pittsburgh coalbed for 5 yr in advance of mining. This report estimates the capital investment and operating cost of recovering 325 MMft3 of methane gas per year and the selling price of approximately 317 MMft3 of gas per year. The labor, equipment, and supply requirements were determined from those of a previous directional hole drilled at the Emerald Mine, near Waynesburg, PA. The cost of equipment, materials, services, and labor are in third quarter 1982 dollars. They were obtained from vendors, contractors, and the U.S. Department of Labor. Findings indicate a total capital investment of $1,381,160. Annual operating cost amounted to $167,690. At a wellhead price of $2.05 per thousand cubic feet, the sale of approximately 317 MMft3 of gas per year results in a rate of return on investment of approximately 25 pet.

Jan 1, 1984

Protect mine rescuers from heat-induced stress that drastically cuts their endurance and saps their strength. Approach To prevent exhaustion caused by thermal stress, a rescuer can wear a liquid-cooled hood and vest which absorbs heat, thereby reducing the heat-induced strain on the rescuer's heart and circulatory system. How It Works Liquid coolant is continuously circulated through a self-contained system in which the coolant is chilled by a heat sink on the wearer's belt. The coolant, which is a mixture of alcohol and water, is pumped from the heat sink to bladders inside the hood and vest where it absorbs body heat. After absorbing heat In the hood and vest areas, the coolant returns to the heat sink where it is rechilled by passing through a tube coiled around a steel can containing a block of ice. To adjust the temperature of coolant leaving the heat sink unit, a valve can be operated by the wearer, causing part of the flow to bypass the coil. A small pump and a rechargeable battery are also part of the assembly.

Jan 1, 1979

By Raja V. Ramani, Robert L. Frantz

"The U.S. Bureau of Mines (USBM) established on August 15, 1983, a Generic Mineral Technology Center (GTC) for Respirable Duet within the Mining and Mineral Resources Research Institutes (MRIs) at The Pennsylvania State University (PSU) and West Virginia University (WVU) in association with participating MRIs at Massachusetts Institute of Technology (MIT) and the University of Minnesota (UMN). The primary goal of the Center is to reduce the incidence and severity of respirable dust disease through researching and advancing the fundamental understanding of all aspects of respirable duet associated with mining and milling and the interaction of dust and lungs. Other Center activities include the training of engineers and scientists, graduate students and undergraduate students through their respective institutions, and the technology transfer to the industry. The Center also serves as the reference center for publications in the respirable dust area.Exposure to respirable contaminants in mine atmospheres has long posed a serious hazard to miners. The control of these hazards, some of which can have sudden and catastrophic effects and some others, slow and long enduring consequences, has been a major concern for labor, management and government alike. This concern has manifested itself in four primary mechanisms of control -- (1) regulatory control through minimum standard setting by the passage of mine health and safety laws, (2) engineering control through design and operation of mines according to the best recommended practices, (3) interaction of dust and lung control through periodic physical examinations, wearing personal protection devices, etc., and (4) legal and social control through workmen's compensation laws for occupation related health deterioration.The stated objective of the Federal Mine Safety and Health laws is to ""... permit each miner the opportunity to work underground during the period of his entire adult working life with-out incurring any disability from pneumoconiosis or any other occupation-related disease ....""Significant progress has been made in lowering the dust levels in mines since the inception of the Bureau's respirable dust research program. It is generally agreed that mines are less dusty today than they were a decade ago. However, the most serious hazard for workers in the mining and minerals processing industries is still the exposure to respirable dust, and solutions to the problem of respirable dust disease remain to be found."

Aug 31, 1989

By Sidney Katell

This report covers the period January 1962 through December 1962; it is a continuation of the series that began with the publication of Information Circular 7516 in October 1949. Also, it is the fourth in a series of reports prepared under a cooperative agreement between the Bureau of Mines and the American Association of Cost Engineers. The agreement provides for the publication of an annual cost bibliography with the work load evolved in the preparation shared equally. Tile abstracted articles, concerned with all facets of cost engineering in the field of chemical and petroleum plants and related subjects, are from tile following sources:

Jan 1, 1963

By Sidney Katell

This report covers the period January 1962 through December 1962; it is a continuation of the series that began with the publication of Information Circular 7510 in October 1949. Also, it is the fourth in a series of reports prepared under a cooperative agreement between the Bureau of Mines and the American Association of Cost Engineers. The agreement provides for the publication of an annual cost bibliography with the work load evolved in the preparation shared equally. The abstracted articles, concerned with all facets of cost engineering in the field of chemical and petroleum plants and related subjects, are from tile following sources: 1. American Association of Cost Engineers Bulletin. 2. Bureau of Mines Information Circulars. 3. Bureau of Mines Reports of Investigations. 4. Chemical Engineering. 5. Chemical Engineering Progress. 6. Chemical Week. 7. Coal Age. 8. Coal Utilization. 9. Cost Engineering. 10. Hydrocarbon Processing and Petroleum Refiner. 11. Industrial and Engineering Chemistry. 12. Nucleonics. 13. Oil and Gas Journal. 14. Petroleum Management. 15. World Oil.

Jan 1, 1963

By W. D. Mcmillan

"Magnetic surveys made by the Missouri Bureau of Geology and Mines in 931 and 1932 disclosed a large positive anomaly about a mile south of Bourbon, Mo. 3/ Electrical resistivity measurements made by the Division of Geophysical Exploration of the Bureau of Mines in the winter of 1942-43 indicated that the source of this anomaly was in the pre-Cambrian rhyolite at a depth of more than 1,400 feet. 4/In order to determine the character of the material that caused the magnetic anomaly, which might be either a body of magnetite or a large intrusive of basic rock, the Bureau of Mines drilled four holes to depths of 1,800 to 2,300 feet. Magnetite in rhyolite porphyry was encountered at 1,600 to 2,000 feet, and this is doubtless the main source of the magnetic anomaly, although it is possible that additional iron ore exists at greater depth.Hole 1 was apparently located southeast of the source of the anomaly and encountered only small stringers of magnetite. Hole 2 penetrated four mineralized zones having a total thickness of 125.7 feet and an average weighted content of 43.52 percent iron and 31.62 percent silica. These zones were tested again by a deflection hole, 2A, which gave nearly identical indications. Hole 3, 500 feet north of hole 2, penetrated 58 foot of mineralized rhyolito containing an average 43.4 percent iron.Metallurgical tests showed that the silica in the ore is tightly locked with the magnetite. After grinding to minus 100 mesh, a 66 percent iron con¬centrate with 7 percent silica was obtained by flotation."

Oct 1, 1946

By F. J. Gallagher

"INTRODUCTION The purpose of this circular is to present information on the construction and use of reinforced rubber-jatketed tubing and insulatiag air-line couplings in coal mines Where Airdox is used for breaking coal in order to eliminate: insofar as possible, arcing at the face between Airdox tubing and the track or other face equipment.ACKNOWLEDGMENTThe information given by the W. M. Hales Co., Chicago, Ill and the Peabody Coal Co., Taylorville, Ill., regarding the construction and use of rubber-jacketed tubing and insulating couplings in gratefully acknowledged. GENERAL INFORMATIONSince its introduction into coal mines, the use of Airdox has grown in popularity, especially in the Indiana and Illinois coal fields. Its use permits breaking dawn coal on shift, whereas the use of explosives for blasting coal on shift is prohibited by law in those States. Many of the hazards connected with the use of explosives are eliminated. The accident experience in the use of Airdox has been excellent with respect to the number of fatalities or serious injuries per million tons mined.The Federal Mine Safety Code specifies that Airdox lines should be grounded at the compressor and at other points of low resistance along the lines but should not be connected to tracks, pipe lines, or other possible power conductors. The majority of operators in the Indiana and Illinois coal mines, in which Airdox is used, approve the precautions embodied in the code regulationsIf Airdox lines are grounded in accordance with the Code, the following hazards persist:"

Sep 1, 1949

By Sidney Katell

This report, covering the period January 1966 through December 1966, is a continuation of a series that began with the publication of Information Circular 7516 in October 1944. It is the eighth in a series of reports prepared in cooperation with the American Association of Cost Engineers. The abstracted articles are concerned with all phases of cost engineering in the field of chemical and petroleum plants and related subjects. They are from the following sources: 1. American Association of Cost Engineers Bulletin. 2. Bureau of Mines Information Circulars. 3. Bureau of Mines Reports of Investigations. 4. Chemical Engineering.

Jan 1, 1967

By F. A. Rutledge

[An a part of the United States Department of the interior program for the development and use of Alaska raw materials, the Bureau of Mines is conducting an investigation of deposits of nonmetallic minerals accessible to the Alaska Railroad for use in building; materials is In the Alaska Railroad-belt area. The results of the investigations, to date, indices that raw materials for the preduction of brick products are in plentiful supply as cloy in the Anchorage area, as fire clay at Sheep Mountain, and as shale in the Healy Creek coal formations near Healy, Alaska.]

Jan 1, 1953

By V. H. Gottschalk, John Grodd, R. S. Dean

"Elemantary ConsiderationsAlthough magnetiem was first discovered in and derives its name from an oxide of iron found in magnesia and called lodestone its pracical uses date from the discoveries of Faraday concerning its relation to the electric current. We may therefore start our discussion of magnetic properties with Faraday's law for relation between induced electromotive force and the change in a magnetic where e is the electromotive force induced in an electric circuit by a unit rate of change of magnetic flux N, H is the intensity of the magnetic field, S is the area enclosed by the circuit, and i an angle between H and the normal to dS. In the simplest case we could use this law to measure the strength of a magnetic field by passing it at a measured rate through a coil of copper wire and determining the,electromotive force. As a matter of practical convenience, it will be simpler to nee the total quantity of electricity produced by a change of magnetic field. For this purpose we may let i denote the strength of the electric current induced by the change of magnetic field in time in a circuit of area a and resistance R. Then the total electric quantity. Q is given. by"

Mar 1, 1934

By F. S. LOTT

The number of petroleum refineries in the United States decreased from 399 on January 1, 1947, to 390 on January 1, 1948. On the latter date two additional refineries were under construction , a large one in New Jersey and a small one in Texas . This Crude oil charging capacity, based on complete facilities only , increased in 1947 from 5,569,482 barrels to 6,034,252 barrels per day , owing to material gains reported in all of the larger refining districts . great increase in effective capacity is only in part the result of the completion of major new units for crude-oil processing . Much of it is due to rearrangement and minor additions to existing facilities to permit more efficient and complete utilization . Recent experience has apparently demonstrated that many processing units are capable , with greater emphasis upon maintenance and precise controls , of sustained operations at higher volumes than were indicated in their old rated capacities . This situation doubtless has caused some upward revision in capacity data .

Aug 1, 1948

A knowledge of the mechanics of wave propagation through the earth is essential if reliable communication systems are to be designed for coal mine environments. To obtain a reliable basis from which accurate propagation predictions could be drawn, a series of theoretical Studies have been prepared for the Bureau of Mines by Mr. Ramsay Decker of Spectra Associates, Inc. through a subcontract with Collins Radio Group. These reports formulate the analytical techniques from which wee may derive frequencies and antenna configurations that yield the optimum signal-to-noise ratios over the greatest distances in mine environments. The reports of sections 2 and 4 deal with analytical techniques for determining the signal-to-noise ratio within a mine environment for loop-to-loop and line source-to-loop antenna configurations. The analytical results of these reports were then implemented into computer programs to obtain predictions concerning through-the-earth signal propagation. These preliminary predictions are based on noise data compiled by Bensema, Maxwell and Stone, and WVU prior to the extensive research conducted by the National bureau of Standards (NBS). These initial measurements indicated a 20- to 30-dB lower noise level than that measured recently by N BS. The recent NBS data is that used by Collins in the final predictions.

Jan 1, 1974

By E. J. Gleim

The Bureau of Mines customarily publishes lists of equipment meeting its safety standards to keep the mining industry informed as to the development and availability of mining equipment that can be used safely. The present list supplements Bulletin 543, Permissible Mine Equipment Approved to January 1, 1953, as well as Information Circular 7722, Permissible Mine Equipment Approved During the Calendar Years 1953-54. Because standards have been revised and new ones added by the Bureau, this list contains classes of equipment not previously covered.

Jan 1, 1958

By R. V. Ramani, R. L. Frantz

"The U.S. Bureau of Mines (USBM) established on August 15, 1983, a Generic Mineral Technology Center (GTC) for Respirable Dust within the Mining and Mineral Resources Research Institutes (MRls) at The Pennsylvania State University (PSU) and West Virginia University (WVU) in association with participating MRis at Massachusetts Institute of Technology (MIT) and the University of Minnesota (UMN). The primary goal of the Center is to reduce the incidence and severity of respirable dust disease through researching and advancing the fundamental understanding of all aspects of respirable ~~9t associated with mining and milling and the interaction of dust and lungs. Other Center activities include the training of engineers and scientists, graduate students and undergraduate students through their respective institutions, and the technology transfer to the industry. The Center also serves as the reference center for publications in the respirable dust area. IntroductionExposure to respirable contaminants in mine atmospheres has long posed a serious hazard to miners. The control of these hazards, some of which can have sudden and catastrophic effects and some others, slow and long enduring consequences, has been a major concern for labor, management and government alike. This concern has manifested itself in four primary mechanisms of control -- (1) regulatory control through minimum standard setting by the passage of mine health and safety laws, (2) engineering control through design and operation of mines according to the best recommended practices, (3) interaction of dust and lung control through periodic physical examinations, wearing personal protection devices, etc., and (4) legal and social control through workmen's compensation laws for occupation related health deterioration.The stated objective of the Federal Mine Safety and Health laws is to"" permit each miner the opportunity to work underground during the period of his entire adult working life without incurring any disability from pneumoconiosis or any other occupation-related disease ."" Significant progress has been made in lowering the dust levels in mines since the inception of the Bureau's respirable dust research program. It is generally agreed that mines are less dusty today than they were a decade ago. However, the most serious hazard for workers in the mining and minerals processing industries is still the exposure to respirable dust, and solutions to the problem of respirable dust disease remain to be found."

Mar 1, 1989

By E. W. COCHRANE, R. HOPKINS, G

The number of completed petroleum refineries in the United States continued to decline in 1938, but the total capacity to process crude oil increased materially. This information was obtained in connection with the Bureau's annual canvass of refinery capacity as of January 1, 1939. In spite of the addition of a half dozen plants in Illinois and the inclusion in this year's list of several more "pot-stills" in Montana, the total number of plants, and inactive, declined from 551 on January 1, 1938, to 538 on January 1, 1939. was entirely in shut-down plants, as the number of operating plants rose from both active The decline 431 to 435. Yost of the plants dismantled were situated in Wyoming and Texas, parts or several from the latter being transported to Illinois. About 10 more East Texas refineries were dismantled in 1938, leaving about 15 plants in the field, only 8 of which were operating on January 1, 1939. Although the total completed capacity increased from 4,351,151 barrels on January l, 1938, to 4,508,555 barrels on January l, 1939, the operating capacity declined, and the inactive capacity increased about 50 percent, or from 380,955 to 574,770 barrels. These shifts in capacities reflect the comparative slump in the refining industry in 1938 after the prosperous year 1937. Daily average crude runs in 1938 were 3,192,000 barrels, from which it may be figured that the operating ratio for the active units was about 81 percent of crude and for all completed equipment 74 percent. The highest daily throughput in 1938 was about 3,400,000 barrels, at which time the reserve capacity represented in the active equipment was at least 500,000 barrels, in addition to about that much capacity shutdown. In an emergency, much more reliance could be placed on the reserve capacity of the active equipment, as much of the shut-down capacity is obsolete at present specifications and prices. Regarding obsolescence, the refiners reported 418,165 barrels of their idle capacity in good condition on January l, 1939 and 156,605 barrels in poor condition. However, it is probable that the former reflects an optimistic viewpoint. Refinery activity, as represented by new construction and dismantling, declined materially in 1938. The new capacity added in 1938 was 378,350 barrels compared with 394,680 barrels in 1937. Probably 1939 will see a much larger decline, as the new capacity under construction on January 1, 1939, totaled only 142,250 barrels compared with 283,020 barrels the preceding year. The capacity represented by the new plants was negligible throughout

Oct 1, 1939

By Scott W. Hazen

METHODS of determining the grade and tonnage in a mineral deposit have not kept pace with scientific developments in certain other fields. The most commonly used methods of computing ore reserves and grade based on diamond-core-drill sampling are the cross section, the polygon, and the triangle. Tonnage and grade may be determined by these methods with acceptable accuracy, providing a sufficient number of samples is obtained; however, there is no means of determining when an adequate number has been taken or conversely if the deposit has been sampled excessively. It is demonstrated that, by using the techniques of statistical analysis, a mining engineer will be able to determine when a sufficient number of samples has been taken to determine the grade of a mineral deposit within a specified degree of confidence. Using statistical analysis to compute the estimated average grade of the ore makes it possible to compute a fiducial interval, when a distribution of the sample means is normally distributed, so that there is 95-percent confidence in the statement that the true average grade of the deposit is covered by the interval. This report utilizes data obtained from the Maggie Canyon manganese deposit, Artillery Mountains region, Mohave County, Ariz. Four separate exploration projects were conducted at Maggie Canyon between 1936 and 1950. Present economic conditions have made it desirable to determine the amount of 5-percent manganese ore developed by these projects.

Jan 1, 1957

By R. E. Collom

The spontaneous explosion of charges of nitroglycerin placed in deep wells situated in parts of the Ranger and Caddo fields of North Texas has aroused considerable inquiry among operators end others as to the probable agency, or combination of conditions, which causes the explosion.The method now followed, under certain physical conditions of a well, of setting a charge of nitroglycerin and allowing it to explode spontaneously was discovered locally by accident. In certain deep wells where formations, overlying productive strata, cave upon withdrawal of casing, it has been the practice to fire the shot electrically. In some of these operations the electric wires are broken or the firing system is otherwise deranged by pulling casing or the caving of hole prior to the time for firing. Sucn accidents make it necessary for the driller carefully to clean cavings out of the hole to a depth close to the top of the charge, after which in the normal practice, an attempt is made to fire the charge by dropping a ""jack-squib"", fitted with a fuse and detonator, down the well. Mr. R. L, Fowler, production manager for the Pierce Oil Corporation, reports that a delayed shot was thus successfully tired through four feet of caved material lying on top of the nitroglycerin shells.When a shot destined to be fired electrically fails, because of the above mentioned accidental conditions to the electric firing system, much time is required for the driller to run casing into the hole and clean out caved material. It was during the time of such uncompleted operations that the spontaneous explosions first noted took place. Having noted these spontaneous explosions the well shooters now intentionally place a charge in deep holes, which because of probable caves would otherwise have to be tired electrically, and wait for the charge to go off. No detonators are placed with the charge.

May 1, 1920

By Adam K. Smith

Over-exposure to noise remains a widespread, serious health hazard in the U.S. mining industry despite 25 years of regulation. Most other categories of illnesses and injuries associated with mining have improved, with the exception of hearing loss. In order to reduce cases of Noise Induced Hearing Loss (NIHL) in the mining industry, retrofit acoustic treatments and controls are being developed to subdue noise at the source. The Mine Safety and Health Administration (MSHA) coal noise sample data collected from 2000 to 2005 has determined that continuous mining machines rank first among all mining equipment whose operators exceed 100% noise dosage. The continuous mining machine conveyor, used to move coal from the cutting face to the rear of the machine, has been identified as a dominant noise source. A dual sprocket conveyor chain was tested as a potential solution. Sound power level measurements conducted at the Pittsburgh Research Laboratory (PRL) accredited reverberation chamber showed a 3 dB reduction in the A-weighted sound power level when the dual sprocket chain was implemented. Underground results show an 8-hour Time Weighted Average (TWA8 hrs) reduction a 3 dB for continuous mining machine operators. Utilizing this newly developed noise control, along with previously proven controls, provides continuous mining machine operators an opportunity to be within the MSHA-Permissible Exposure Limit (MSHA-PEL).

Jan 1, 2009

By Gary E. Sherman

To aid the U.S. Army Corps of Engineers in their Resource Development Navigation Study of ten existing or proposed port sites in Alaska, the Bureau of Mines examined the potential for mineral development around three Alaska port sites: Iliamna Bay, Kotzebue, and Nome. The mineral deposits near Iliamna Bay include gold, copper, and iron. Development of minerals in this area will require the discovery of new deposits or the definition of additional are reserves at known deposits. The mineral deposits near Kotzebue are primarily gold, copper, coal, lead, and uranium. Based on the character of these deposits, it appears that development of a small-scale mine supplying coal for regional use is the most likely scenario in the near-term. The mineral deposits near Nome are primarily gold and copper. Development of small underground gold mines is possible, however it appears that expanded offshore gold dredging will have the greatest impact on the flow of freight and goods through the Nome port in the near term.

Jan 1, 2011