Search Documents

By Elmer E. Buban

A lightweight compressed oxygen rescue breathing apparatus (RBA) for rescue and recovery missions has been developed by Mine Safety Appliances Company under contract to the Bureau of Mines. The apparatus is a positive pressure, closed circuit system of 4 hours duration. The weight of the complete apparatus, including an optional cooler, is slightly over 30 pounds. Weight reduction over currently available RBAs is achieved through the use of lithium hydroxide for scrubbing C02 in place of conventional chemicals and the use of a composite glass fiber/ aluminum shell cylinder for oxygen storage in place of steel cylinders. Positive pressure is maintained in the breathing circuit at all times by applying a constant spring force to the breathing bag. The harness has been designed to reduce the work of the wearer by redistributing the weight of the apparatus to the wearer's hips.

Jan 1, 1981

By James J. Snodgrass

A new technique was used to obtain detailed sonic logging data in drill holes above the water table at a coal mine site in northeastern New Mexico. The equipment was developed under contract to the Bureau of Mines and the U.S. Department of Energy to indirectly evaluate the in situ structural properties of coal and overburden. The system comprises a hydraulically operated, wall-clamping downhole probe compatible with standard four-conductor logging cable, and a surface control module. Resolution of layering is 0.6 meter (2.0 ft), and a redundancy of data from separate receivers provides accurate timing measurements. Preliminary results in the settled overburden of an excavated long-wall panel indicated a low average velocity zone, extending approximately 18 meters (60 ft) into the immediate roof of the coal seam. Subsequent measurements improved the field and recording procedures to produce high quality waveforms from which both P and S arrivals may be visually interpreted. Over a representative section of interbedded sandstone, siltstone, shale, and coal, Vp and Vs varied considerably even within lithologic units. Compressional wave velocity in the coal seam, Vp = 1,740 m/sec (5,700 ft/sec), was in the range of variability of published data.

Jan 1, 1982

By W. H. Schiffbauer

NIOSH has developed an active proximity warning system called HASARD (Hazardous Area Signaling and Ranging Device) for warning workers as they approach known dangerous areas around heavy mining equipment and other dangerous work zones. HASARD is composed of a transmitter and a receiver. The transmitter generates a 60-kHz magnetic field using one or more wire loop antennas. Each antenna is adjusted to establish a magnetic field pattern for each hazardous area. The receiver, worn by the worker, is a magnetic field strength meter. The received signal is compared against preset levels which are calibrated to identify levels of danger. The receiver outputs can include visual, audible, and vibratory indicators and it can also be made to disable machine functions. HASARD was field tested on a Joy 12 continuous miner, a Komatsu 210 M Haulpak, and on a highwall launch vehicle. Slight modifications were made for each application. HASARD provided warnings as designed and proved to be rugged enough to withstand the harshest of production environments.

By James S. Wroth

The Act of Congress approved June 25, 1926 (Public Act 424, 69th Congress), authorized joint investigations by the U. S. Geological Survey and the U. S. Bureau of Mines to determine "the location, extent, and mode of occurrence of potash deposits in the United States." The particular deposits selected for exploration were the extensive rock-salt formations underlying large areas in western Texas and southeastern New Mexico, from which potash salts had been identified in the cuttings and sludges from oil wells drilled with cable tools. The evidence of these sludge samples was qualitative only and beyond definitely proving the presence of potash salts in the salt beds, gave little clue to the possible size, richness, or extent of the potash occurrences.

Jan 1, 1929

By M. D. Aldridge

The results of a two-year research effort aimed at improving communication systems in coal mines is reported. A review of communication methods presently used in coal mines is presented. Theoretical and-experimental results of a four pronged effort in the areas of (1) through-the-earth propagation, (2) paging system design, (3) improvement of wired telephone systems, and (4) carrier current systems are described. Auxiliary systems not included in the above are considered briefly. Various conclusions are drawn in light of practical constraints and the needs of the mining industry. The study clearly demonstrated the need for nine communications to be designed on system basis. The viability of new technology for providing reliable mine communication for improving mine safety and operating efficiency is shown.

Jan 1, 1973

The Bibliographic Data Base is the result of a literature search con-ducted as one task of the technology assessment of current and advanced logging techniques, sponsored by the United States Bureau of Mines. After compilation, the bibliography was converted to an automated form for ease of utilization, and to allow for maintaining and updating the data base. The data base covers articles, symposia, books, patents, corporate and government reports, and other literature concerned with some aspect of borehole logging from January 1969 through December 1975. Periodic up-dating will be necessary to keep the data base contents in step with developments in the rapidly advancing field of application of borehole logging to mining. Many bibliographic indexes were scanned for entries relating to the subject of interest, and those entries which were included in our data base contain a reference to the bibliographic index in which they were listed (see Section 2.4.7). With the aid of these indexes, a vast number of publications, including foreign reports and publications, have been scanned for works relevant to borehole logging technology.

Jan 1, 1976

By Thomas J. Peters

Tungsten, silver, lead, zinc, and placer gold occur in the Cucamonga B RARE II area (no. B5174). A strata-bound, scheelite-bearing zone at the Blue Diamond prospect (fig. 1, no. 1) contains an estimated 16,000 tons (15,000 t) of identified, subeconomic resources averaging 0.16 percent tungsten trioxide (W03). There is a high potential for discovering additional tungsten resources at this property. The California-Hercules prospect (fig. 1, no. 5) ha; a mineral occurrence which contains an estimated 1,000 tons (900 t) of tactite averaging 1.3 oz silver per ton (45 g/t), 0.75 percent lead, and 0.72 percent zinc. Another occurrence, at the Blew Jordam Prospect (fig. 1, no. 4) has an estimated 100 tons (90 t) of tactite averaging 10 oz silver per ton (340 ,/t), 3.75 percent zinc, and 2.3 percent lead. There is a moderate potential for discovering silver, lead, and zinc resources at these prospects, which are in metamorphic pendants. There are a few lode gold prospects in the area (fig. 1, nos. 3, 11, 14) are on geologic structures which parallel the San Andreas Fault, northeast of the area. These deposits are not well exposed and have been historically unproductive. Placer gold in area B occurs locally in the beds of intermittent tributaries to Lytle Creek (fig. 1, nos. 10, 12, 13) in concentrations as high as $1.17 per cu yd ($1.53/cu m, at a gold price of $450 per troy oz). The deposits have no significant volume, but could be utilized for recreational panning and suction dredging. In the Cucamonga C RARE II area (No. C5174) placer gold occurrences locally contain as much as $1.23 per cu yd ($1.61/cu m). However, gravel containing the gold appears to be limited to stream beds, and does not occur in sufficient quantity to constitute resources. Recreational panning and dredging also may occur in this area.

Jan 1, 1983

The condition of the domestic mining industry is obviously affected by the cycles in general business conditions. This study, the results of which are presented in a series of 78 charts, attempts to examine the interrelationships between the general business indicators and the major statistical measures for the base-metals industries during the cycles in the United States economy following World War II. For these industries the cyclical problem is perhaps less acute than the secular-trend problem. However, short-run fluctuations in production and employment do have very important impacts upon the welfare of the regions which derive a significant portion of their income from base-metals mining and processing industries. Any information concerning the normal patterns of development as the industries enter into a cyclical recession will permit better forecasts and perhaps help promote measures to alleviate the distress that occurs. Also, a systematic study of the comparative movements among the statistical measures during a series of cycles can bring to the fore the economic causation involved, and perhaps, after intensive study, can lead to a better method of short-range forecasting for these industries. This study has not fully achieved these aims. However, observations which significantly aid the interpretation of the current monthly statistics on these commodities are made, and some very general conclusions are drawn. The charts are presented so the interested people can examine them and draw additional conclusions. The charts refer specifically to cyclical analysis. The technique of indexing each cycle to its turning point effectively subordinates the longer term trend movements of the data. Thus, certain general conclusions flowing from this study and from the continuing economic research of the Office of Chief Economist will aid the reader by clarifying the frame of reference within which the charts should be examined.

Jan 1, 1961

By Gary A. Kingston

Rolled steel, steel forgings, and steel castings in the Pacific Northwest (Washington and Oregon) are produced principally in the Seattle, Wash., and Portland, Oreg., metropolitan areas. Steel-mill products are rolled from carbon and some alloy &eels by three companies into shapes such as reinforcing bar, rods, rounds, squares, flats, and hot-rolled strips; structural shapes, - such as angles, channels, and I-beams, also are rolled. Carbon and alloy steel ingots are poured and forged at a Seattle plant into ship shafting, drive shafts, billets, slabs, bars, rings, hooks, and other items. Static, shell, investment, and centrifugal castings are produced at 19 steel foundries in a wide range of steel specifications. All Pacific Northwest steel output is based on remelting steel scrap. Local iron ore might be used in the future to supplement steel scrap as a metal source. Ore reduction would probably be achieved by methods other than the blast furnace. Current melt-shop practice and problems are basically the same in Pacific Northwest steel plants as in cold-melt shops in other parts of the country. Quality steel production is receiving more emphasis in this region with the installation of modern analytical equipment and vacuum pouring and melting facilities.

Jan 1, 1962

By Richard A. Winters

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied 34,000 acres of the 58,040-acre Little Jacks Creek Wilderness Study Area (ID-111-6) in order to evaluate the mineralized resources. The study area is located in Owyhee County, 10, about 21 miles southwest from Bruneau. No mining districts are in the study area, nor were any mines or claims recorded or found. The northern half of the area was covered by oil and gas lease applications; all were cancelled prior to 1985. No economic concentrations of minerals were found in the study area. INTRODUCTION This report describes the USBM (U.S. Bureau of Mines) portion of a cooperative study with the USGS (U.S. Geological Survey) to evaluate mineral resources and potential of the Little Jacks Creek study area at the request of the BLM (U.S. Bureau of Land Management). The USBM examines individual mines, prospects, claims, and mineralized zones, and evaluates identified mineral and energy resources. The USGS evaluates potential for undiscovered resources based on areal geological, geochemical, and geophysical surveys. Results of the investigations will be used to help determine the suitability of the study area for inclusion into the National Wilderness Preservation System. Although the immediate goal of this and other USBM mineral surveys is to provide data for the President, Congress, government agencies, and the public for land-use decisions, the long-term objective is to ensure the Nation has an adequate and dependable supply of minerals at a reasonable cost.

Jan 1, 1986

By Donald F. Reed

The bauxite deposits of Tippah and Benton Counties in northeastern Mississippi were developed by drilling as a part of the investigation by the Bureau of Mines of the domestic sources of supply of aluminum. The primary purpose of investigations of this nature was to provide essential information to the war agencies of the United States Government and to assist owners and operators of mining properties in the production of minerals vital to the prosecution of the war. These reports are based upon the field work of the Bureau of Mines and upon data made available to the Department from other

Jan 1, 1948

By Robert C. Bates

Variations in water percolation rates through saturated cohesionless hydraulic backfill (mill tailings) have been studied in relation to the many physical aspects of the system to determine the most important factors in causing these variations. A multivariable least-squares regression analysis of 135 separate tests shows that a reliable estimate of the water percolation rate through typical hydraulic backfill can be made if the bulk density (unit weight), specific gravity, and grain-size distribution are known or can be estimated. Equations for predicting percolation rate, coefficient of permeability, and seepage velocity are developed both for the range of data analyzed and for extrapolation. The prediction equations for use within the range of data studied are quite accurate, while the ones developed for extrapolation are less accurate but still give reasonable approximations of flow rates. The equations given are valid for cohesionless materials that are free of clays and micas, exemplified by classified mill tailings. The equation developed for predicting percolation rates is as follows: 1nP20 = 11.39147 + 2.853422 1n(VR X D10) + 0.1747436 VR X Cu -178.8039 D10 X D50 + 311.7034 (DSO )3, (1) where P20 = percolation rate, inches per hour at 20° C; correction factors for other temperatures are given in the text, VR = void ratio, dimensionless, D10 = effective size (diameter in millimeters of the 10-percent-finer grain size), Cu = coefficient of uniformity (ratio of the diameter of the 60-percent-finer grain size over D10), D50 = average size (diameter in millimeters of the 50-percent-finer grain size), and In = natural logarithm (log to the base e). The prediction equation for percolation rate is rather complicated, so for practical use a nomograph that simplifies the solution of the prediction equation was developed.

Jan 1, 1967

By J. R. Thoenen

In June 1929 the Bureau of Mines issued a 13-page information circular entitled "Mineral Wool," which was one of the first publications to present to the public Rome technical aspects of the mineral-wool industry. Since then several articles on the subject have appeared in the technical press as well as in publications of State organizations. Inquiries for information on mineral wool have continued to be received by the Bureau of Mines in large number, and in 1935 it was decided to make a field survey of the plants then producing and to collect therefrom technical data to be compiled in a paper for nubile distribution. With the cooperation of the industry, this survey was made, and Information Circular 6984, Mineral Wool, was published in January 1930. The issue was exhausted after a few months, and requests for copies continued to come to the Bureau. As opportunity arose, further field studies were made in American as well as Canadian plants. The present circular contains the essential information in Information Circular 6994 together with date from later field studies.

Jan 1, 1939

By Douglas Talley

This report describes a 4-inch diameter borehole probe which contains a low light level TV camera, magnetic compass, light illumination source, bottom/water detector sensor and a pointing angle sensor. The camera viewing angle is at a right angle to the probe's body. All data from the sensor is multiplexed into the closed circuit camera video for transmission on a single 50 ohm coaxial cable to a surface control unit. Likewise control of the probe's power, zoom lens, focus, panning and aperture is accomplished via a down-link multiplexed on the same cable.

Jan 1, 1984

By Jeffrey S. Newman

This report establishes a methodology for the evaluation of gas detection devices and is the result of a critical investigation into the basic principles defining gas detector performance. A scheme is presented to evaluate the performance of a test sample of gas detectors based on the detector type and intended application. Test procedures, worksheets, test apparatus, glossary and statistical methods for handling test data arc given. In addition, evaluation standards and test parameters are identified. It is intended that this report serve as a comprehensive framework for the eventual certification of all gas detectors for mine applications. A plan is proposed and recommended for the quantification and implementation of evaluation standards for gas detection device certification.

Jan 1, 1980

By G. F. Kuncir

The time-cost-risk analysis described herein was performed as part of an evaluation of the Advancing Oil Shale Mining Technology Program performed by The Aerospace Corporation. The objectives of this analysis are to assess the feasibility of the program relative' to time and cost constraints, and to determine the probabilities of achieving various technological goals. A combination of standard program planning and analysis techniques were used to achieve these objectives. These included a critical path analysis, a resource allocation analysis, and a risk analysis.

Jan 1, 1977

By Eugene T. Sheridan

The Bureau of Mines annually canvasses the fuel-briquet and packaged-fuel producers in the United States and publishes economic data on these industries, based upon reports submitted voluntarily by producers. This publication lists all producers that reported commercial production to the Bureau for 1960 and presents data on individual plants. The companies named herein represent virtually all producers of processed minerals fuels. A few small plants may not have been canvassed or failed to respond to the survey because some of the smaller plants operate intermittently and the survey is voluntary. All plants that reported commercial production were included; regardless of size. Specifically excluded were plants that manufactured briquets from wood charcoal. Fuel briquets and packaged fuel are manufactured solid fuels, produced by mixing fine-sized mineral fuels with binding materials and compressing into small individual shapes, Briquets are produced in pillow-shaped and cylindrical form, are 2 to 4 inches long, and weigh 2 to 4 ounces. Packaged fuel consists of 3- or 4-inch cubes; 6 or 8 of which are wrapped together in heavy kraft paper to form a package weighing 10 to 15 pounds, Briquets are durable and may be stored and handled as bulk fuel; packaged fuel breaks easily and must be stored indoors to prevent it from deteriorating. Whereas briquets are consumed in many areas as a general residential fuel, packaged fuel is more of a specialty item, used at times to supplement other fuels. Packaged fuel is burned without re-moving the paper and is referred to as the "white glove" fuel.

Jan 1, 1961

By E. O. RHODES

Germany's' wartime coal-tar industry had two main branches, which can best be considered individually because their raw materials, operations, and distributions were almost completely separated. One branch, old and well-established, was concerned almost entirely with processing coal tar produced by the high-temperature carbonization of caking bituminous coal. Carbonization was effected principally in byproduct- coke ovens and to less extent in vertical, horizontal, and inclined retorts. The high-temperature tar was all processed in tar-distilling plants that handled high-temperature tar almost exclusively.

Sep 1, 1947

By P. F. Sands

This U.S. Bureau of Mines report reviews the state of the art in blind pneumatic stowing of backfill in voids in abandoned coal mines. It contains a short history of the development of pneumatic equipment in mining and four recent case histories of blind pneumatic stowing. Limitations of pneumatic stowing in terms of equipment wear, costs, backfill material, and methodology are discussed, and some new procedures and designs are reviewed. A bibliography covering pneumatics in mining is included also. This report provides background for the preparation of a Bureau test program in which the variables affecting the efficiency of pneumatic backfilling will be studied using a full-scale surface test facility.

Jan 1, 1990

By Duane L. Abata

This work, conducted under Bureau of Mines contract, deals with the development of a computer graphics software package that will: 1. display mine ventilation schematics and other representative Illustrations for a real-time data acquisition system under development by the Bureau, and, 2. utilize the Bureau-owned Minefire and Ventilation Code for display of ventilation on and contamination predictions. The software package has been written try operate on a 64K, Z-80 based microprocessor-computer. The project has been divided into two phases. The first phase dealt with the development of the graphics software The sec rind phase dealt with the retrofit of the Minefire and Ventilation Code to the Z-80 microprocessor-computer.

Jan 1, 1984