Search Documents

By Larman J. Heath

Wellbore enlargement was tested using hydrazine hydrate in a gas-storage well in Ohio to increase the well productivity. The wellbore was to be enlarged by chemical disaggregation of the sandstone adjacent to the wellbore. Productivity immediately declined 49.1 percent and gradually declined to zero in 7 months. A down-hole camera survey showed a white-to-gray precipitate covering the entire wellbore surface. The precipitate was chemically analyzed and identified as mostly carbazic acid, a hydrazine derivative of carbonic acid. Formation of this precipitate was not anticipated; this viscous sub-stance caused the gradual loss in productivity of the well. The wellbore was not enlarged. Laboratory tests were run to determine what clay stabilization measures could be taken in sandstone cores to prevent clay swelling and particle migration caused by hydrazine hydrate. Normal clay stabilization methods did not prevent the virtually complete loss in permeability to hydrazine hydrate. Other laboratory tests using natural gas diluted with small amounts of carbon dioxide confirmed the ease with which carbazic acid could be formed in a hydrazine hydrate-saturated environment within and adjacent to the wellbore.

Jan 1, 1970

By Paul Hatmaker

"The Bureau of Mines recently has issued a general information circular covering briefly the origin and occurrence, properties, uses, exploitation, and marketing of diatomite. Since this publication was prepared, additional information has become available regarding one of the newer uses of diatomite — that as a filler in battery boxes. As this market is rapidly becoming one of the important outlets, a brief discussion of such use may be of interest.Diatomite is a mineral substance composed principally of the skeletal remains of diatoms. The skeletons of these microscopic flowerless water plants are made from silica present in the water in which these tiny plants live. The minute shells or ""casts"" accumu¬late in the bottom of lakes, ponds, or inland seas, and eventually become more or less consolidated into beds of diatomite.The uses of diatomite depend largely upon its peculiar properties. Diatomite is a highly porous substance and possesses marked absorptive powers. The large percentage of pore space makes the material very light in weight. It is relatively insoluble in most solutions.The largest deposits in the world are found in California, but diatomite occurs in many other Western States and also is found in a number of places along the Atlantic seaboard. Outside of the United States diatomite occurs in many countries; Algeria and Germany are among the largest producers.Usually diatomite is mined either by underground or open—cut methods. In some instances it may be dredged from lake and swamp bottoms. It must be dried prior to grinding or other preparation for market, and for many purposes must undergo a complex sizing and grading system for removal of such impurities as sand and clay and for classification of the material to the various sizes desired,"

Mar 1, 1931

Reduce potential for steering errors during tramming of articulated vehicles, particularly when the operator is seated to the rear of the machine pivot point and is tramming in reverse. Approach Position-sensing and feedback cylinders were applied to the steering cylinders of two S&S cleanup tractors to cause the steering-control lever to match the orientation of the vehicle sections. The vehicles were tested in two working mines. How It Works A position-sensing cylinder (see Figure 1, Item A) is attached to one of the steering cylinders in the cleanup tractor steering system. As the steering cylinder piston rod is actuated by movement of the control lever, hydraulic oil flows from the position sensing cylinder to the feedbck-cylinder (B), causing the feedback-cylinder piston and rod to move. The outside end of the rod repositions the the steering-control lever until its angular position corresponds to the orientation of the vehicle sections.

Jan 1, 1978

By Frank A. Peters

An evaluation is made of a lime-soda sinter process for extracting alumina from clay. In this process, alumina is extracted by sintering clay with soda ash and limestone and then leaching the sinter with a dilute sodium carbonate solution. The sodium aluminate solution formed during leaching is separated from the residue and treated with lime in autoclaves to remove dissolved silica before alumina trihydrate is precipitated with carbon dioxide. The tri-hydrate is then calcined to a-alumina. Two options, dry grinding and wet grinding, are used in the sintering step. The fixed capital costs for plants producing 1,000 tons of alumina per day are $72 million for the dry grinding option and $66 million for the wet grinding option on a Marshall and Stevens chemical equipment index basis of 240.0. Specific geographic locations of plant and raw material sources are not assigned, but, since this process requires large quantities of both lime-stone and clay, the plant site is considered as variable with relation to the clay mine and limestone quarry. A nomograph is given to find operating costs at various delivered costs of clay and limestone. If the plant is located nearer the limestone quarry so that the delivered cost of clay is $2 per ton and the delivered cost of limestone is $1 per ton, the operating costs are $76.47 and $71.61 per ton of alumina for the dry grinding and wet grinding options, respectively. On the other hand, if the plant is located nearer the clay mine so that the delivered cost of clay is $1 per ton and the delivered cost of limestone is $2 per ton, the operating costs are $80.15 for dry grinding and $75.34 for wet grinding.

Jan 1, 1967

By Kray Luxbacher, Erik Westman, Peter Swanson

Three-dimensional time-lapse velocity tomograms were generated to image stress redistribution around a longwall panel to produce a better understanding of the mechanisms that lead to ground failure. Mining-induced microseismic events provided passive sources for the three-dimensional velocity tomography. Surface-mounted geophones monitored microseismic activity for 18 days. Most similar studies have utilized active sources including longwall shearers, controlled explosions, and hammer blows. These active sources generally require a person to initiate and measure the location and time of the source, and are not conducive to continuous monitoring. This method utilizes mining induced microseismic events as passive sources and lends itself well to continuous monitoring. Two event location methods were compared in order to move toward quantification of tomographic results in terms of ground conditions. Additionally, LAMODEL was utilized to determine the expected stress distribution around the longwall panel and compare these images to the velocity tomograms. Eighteen tomograms were generated, one per day, and high velocity regions in the set of tomograms generated from the initial location algorithm correlated with abutment stress redistribution predicted by numerical modeling. This research is significant as it has the potential to improve safety in underground mines and is the only example of long term passive velocity tomography implementation for the purpose of inferring stress redistribution around an area of active mining. Though still immature, this technology has the potential to allow mine personnel to image areas of active mining on a regular basis and detect areas with anomalous velocity distributions indicating potential safety hazards.

By A. M. Poston

Introduction of radioactive elements into ore samples and/or pregnant liquors and radiometric tracing thereof have greatly improved control of fusion and extraction studies on beryllium ores and products. Extractive metallurgical research on beryllium, normally guided by the usual laborious analytical methods, is both costly and slow. Recognition of this problem by the Bureau of Mines led to the development and application of radioisotope tracer techniques" as a substitute for chemical analysis at the Salt Lake City Metallurgy Research Center, The result was that much faster progress at significantly lower cost was achieved. This report discusses the problems encountered and resolved in using radioactive tracers and radiometric methods, defines the conditions and techniques for their effective use, and delineates the limitations and flexibility inherent in applying such methods in laboratory-scale beryllium research.

Jan 1, 1962

By Kenneth H. Johnston

This report describes in detail three waterflooding projects and a pres-sure-maintenance project in Butler and Cowley Counties, Kans., that will be visited on the 1963 annual spring tour of the Kansas-Oklahoma Waterflood Association. Among the unique features of the projects are the flooding of five oil-producing horizons separately with injection water furnished by two water treating plants. Discussion of the individual projects includes information on their early history, the source and treatment of the injection fluids, oil production decline curves, and the results of water injection on oil production.

Jan 1, 1963

By William O. Vanderburg

This paper describing the mining practices at the Argonaut mine, Amador County, California, is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The mining practices described are those used in exploiting the low-grade gold ores in the heavy and swelling ground that occurs on the Mother Lode belt. The author acknowledges the assistance of E. A. Stent, vice-president, James L. Fontenrose, cost clerk, Joseph Mohorovich, mine foreman, of the Argonaut mine, and of E. D. Gardner, supervising engineer, United States Bureau of Mines, Southwest Experiment Station, Tucson, Ariz.

Jan 1, 1930

As longwall shields are lowered in preparation for advance, dust from the canopy falls directly into the air stream with the potential of becoming entrained. Historical dust sampling data from the early 1980s shows that shield advance contributed an average of 12 percent to the airborne respirable dust levels found on longwalls in the United States. Data from the 1990s indicates that shield dust liberation had increased to an average of 23 percent. Increased longwall production levels over this time resulted in the need to move a larger number of shields during each shift, while an increase in air velocities on the face was also occurring. These factors combine to suggest that greater quantities of shield dust are being entrained into the face air. A series of controlled laboratory tests were conducted in a test stand simulating shield dust entrainment to evaluate changes in airborne respirable dust levels at different air velocities. Significant differences in respirable dust entrainment were observed. The test facility, test methodology, and dust sampling results will be reviewed and discussed

[lllc purpabr at thla report Vd, Lu JeLermlnr the health ar1J sdfet?; Nene11Le a octatc?J ultll Lne oar L.t support Ydlll ..up.I,ated lu dltetllative cupPurt svsLem, larrellLty hcle.g uaeJ af the Len,::rat 1, UI.Jlng 11-al tl. .1 a d 1 c L V h S LIdl'. L dal. I -ten- lu L he tt I .. L'., etuJ I e. 11'? L_1,1'1,11 .Jtd.. it, ..urn,at'l core ,LuJICCill JhLdll, an.: ...,La -IL .utia_tel .an LI?r oar of -l: l,.!rl .a..a. Ma terI.I auJ ...11,mc[Ii -ldla,tutcle 11. LI.ac .uwIttIca Welt a, a.. V.alte,, L.. .:Ltail, ..,,L., uI. LuClu,alug) Lelll anci ur devel?puJ I.,r Cul r1 , all. ...~.,rLrI Vt,ILt 1.'ere ~e,1C L? .Lher Gentiaii m111cc t, UL.-rye a Variety o. a rL vyl I pp.1Ca:t..n:. 'a.la IrL ..,_wLeiti, Iapl,.III ,tall ~,..:. IL all, maLertdl c1,arait-erlstIcs, JIRICn,IUIIe. and laden ul1.1 ILc rrgatrelaeuls. ,1 r.? p.'rt .a pro-1Jd, labor rep altrlarnts Jdta and illtlitI ieS tie l,ealtll d?J ,atetV ISSUC ,u-1aled Wit su furl Wall a an, CJl,wttuctSOn, I'aLentiaI appll.at1ou:. Ior support Walt, ,a,. , a, sdV.u,L111 .., u.1 retreating lungval1, single -t r-, roar al,- pi r. [,-+ln, anJ SuhIU..,Ina, Sill] b1OpplllgL ale 1:111neated aid al? e.aIWRac AS Sddemcni LV pre,C'IIL..: .,f LI. Clabllhty r+t rlul,I.,y111I? ulg4,rt .I Le.l,lwlug,. Lr i,,,rCASC Lllc rtCVLLrS rat, u., retrc.+tlnp .unui.,11? ur L., elply, A d v Ctnp IuI-,wall in uer;-!y iy1ng seam, . 11111.a1L .a1,.'iI1.-I,.. nr S.IU1tIVlil a1 milItlI; Lust, La LIldnt;2S L.~ gey support Vait Id tdmcLera la dlaa presents,.]

Jan 1, 1980

By Joseph T. Singewald

The possible value of the red hematite iron ore of the southern Appalachian States, if some practicable method of concentrating it could be devised, has long been recognized. The ore is very low grade, and although in enormous quantities, particularly in the States of Alabama, Tennessee, and Georgia, is only at a few points rich enough to work, and even the best of it ranks among the lowest grade iron ores being mined in the United States. A cheap method of beneficiating this ore would make enormous quantities available and vastly increase the iron-ore resources of the country. However, this low-grade ore in effect constitutes a potential iron reserve, and as long as ample quantities of ore can be obtained elsewhere the question of its utilization does not demand immediate notice. Where these ores are in part of workable grade, however, a problem of more immediate importance arises which, from considerations of economy and prevention of waste in their mining, ought to be solved or, at least, attacked as quickly as possible. Where these ores are being worked they are usually intimately associated with lower-grade material that in mining is left behind. The difficulty and expense of going into ground broken by old workings makes the recovery of this lower-grade ore practically impossible and it is lost forever. Success in concentrating the red ores, therefore, would save material that is now being irretrievably lost. The successful large-scale concentration of law-grade ore in the last few years on the Lake Superior iron ranges should encourage the attack of similar problems in the Birmingham district.

Jan 1, 1917

Provide the mining industry with a simple, accurate and readily available means of measuring the gas flow from pipe outlets such as gob holes Approach The Bureau of Mines conducted laboratory studies to establish correction or method factors for anemometers when used to measure gas flow from pipe outlets. Using the Anemometer Anemometers are used by the mining industry to make air velocity measurements in mine entries. Although the instrument has no appreciable influence on the airstream in mine entries, especially since the cross-sectional area of an entry is much larger than the cross-section of the anemometer, correction or method factors are used to correct the center line anemometer velocity to average velocity. This adjustment is made because the air velocity in a mine entry is highest in the center and lower at the sides. Anemometers can be used to measure gas flow from small diameter pipe outlets; however, since the instrument diameter is much larger than one-sixth of the pipe diameter, it will influence the air-stream from these small outlets. Resulting velocity measurements are erroneously high by as much as 30 percent. Method factors must be applied to such anemometer measurements taken at pipe outlets. Through a research investigation the Bureau of Mines established a set of method factors for center-line anemometer readings taken at the discharge end of 4-to 8-inch diameter pipes. These method factors were combined with method factors which were developed by the National Coal Board of Great Britain for 12-to 30-inch diameter pipes. The anemometer was mounted on the end of a short rod and held against the pipe for support except on the 4-inch pipe where the instrument was started and stopped remotely to prevent hand interference with the air-stream during measurements. Method factors were determined by comparing the anemometer measurements at the pipe outlet to the true average airflow which was simultaneously determined upstream by venturi measurements. Consequently, a method factor is nothing more than the ratio of the true velocity to an anemometer measurement.

Jan 1, 1987

By Bryan Buchholz, N. Kumar Kittusamy

Previous studies indicate that operators of heavy construction equipment are afflicted by musculoskeletal injuries of the arms, shoulders, neck, and lower back. These injuries appear to be due to excessive periods of sitting (static posture), work intensity, whole-body vibration, high resistance levers, repetitive motions, and awkward postures. (2-5) Although numerous studies have shown an association between operation of heavy construction equipment and symptoms of musculoskeletal disorders, very little research has been performed that systematically characterizes operating engineers' exposure to ergonomic hazards. The objective of this study was to systematically characterize the ergonomic hazards associated with excavating operations. As such, the following were performed: (1) vibrations were measured at the operator/seat interface (X, Y, and Z axes), and at the floor of the cab (Z axis); (2) psychophysical ratings of whole-body vibration (WBV) level and overall seat design were obtained; and (3) postural assessments of the job were made. Methodology This study evaluated an inexperienced female operator performing excavation, utilizing two different pieces of equipment. The operator was 37 years old, 162 cm tall, and weighed 80 kg. She had approximately 15 hours of operation time (experience) on the equipment evaluated. The two pieces of equipment used were: a Case Super 580E (1986) backhoe/loader, and an Insley H-2000 excavator (1975) (see Figures 1 and 2). More evaluations were performed on the backhoe/loader than on the excavator. The following evaluations were performed on the Case equipment: 1) vibration levels at the seat and floor; 2) psychophysical ratings of the overall seat design and vibration levels (for the task duration, and for an 8 hour duration); and 3) postural assessments. For the Insley equipment, all of the evaluations were performed except vibration measurements. When the evaluations were conducted, the following environmental conditions were noted: the temperature was 31°F, and soil and terrain conditions were rough and frozen.

By A. R. T. Denues

"INTRODUCTION The orienting phases of the current investigation of cushioned blasting in the Explosives Division of the Bureau of Mines were indicated in a previous publication (5) 3/. Pertinent literature reviewed therein indicated a highly controversial field. This emphasized the need for experimental studies of many factors that affect the health and safety of miners and the efficiency of mining operations. Results of some orienting tests showed marked effects on practical hazards. Further, they emphasized the necessity and importance of the contemplated investigation. The scope and general plan of these practical inquiries into the safety of cushioned blasting were indicated.This investigation of cushioned blasting relates to the various means employed to reduce the intensity of application of energy from explosive actions in boreholes. It has been suggested (from p. 19 of reference 5) that the divisions of this work would correspond to the salient hazards affected by cushioned blasting. These include the ignition hazard, hazards from poisonous gases, and other practical hazards in the blasting technique. The ignition hazard was resolved into two components of approximately equal weight. These include studies of effects upon (1) the incendivity of blown-out shots and upon (2) the occurrence of such shots. Experimental studies of effects on the incendivity of blown-out shots were first undertaken. Questions of the best procedure for making these evaluations have been adduced, and the interpretation and utilization of the results of gallery testing seemed to require detailed attention; some preliminary general considerations of such testing were therefore necessary."

Jan 1, 1943

By Stephen C. Tadolini, Peter (Yunqing) Zhang

A unique circumstance created by monitoring a pre-driven longwall recovery room permitted measuring the stresses of a coal pillar throughout its entire life cycle in less than a week. A fender pillar, created in approximately the middle of a longwall panel at a depth of 650 ft, transformed from a solid barrier pillar - to a yielding pillar - to a residual pillar as 3 ft slices were methodically removed with the longwall shearer. The complete transformation, or life cycle, took place in less than 12 hours. The stresses were quickly transferred from the pillar onto the standing pumpable concrete supports and into the outby pillars. Roof to floor closure measurements, combined with the timing of the pillar behavior, provides a detailed look at the uncontrollable convergence of underground mine openings. Pillars remain the most important form of “primary support” and understanding these life cycles is vital for safe and efficient mine design, in both room and pillar and longwall panel extractions.

By C. W. Davie

"This paper is the second of a series of progress reports4 on a study of the hydrometallurgy of manganese which is being conducted in an endeavor to make possible utilization of the large deposits of low-grade domestic manganese ores that occur in several States.There are at least four processes in which a knowledge of the action of SO2 gas on manganese oxides at elevated temperatures may prove of value.One of these involves dissolution of manganese from ores. The Bureau of Mines has investigated the hydrometallurgy of manganese by a process in which SO2 gas, a waste product at many smelters, is passed into water to form a solvent for manganese. Although several manganese minerals were readily dissolved, rhodochrosite (MnCO3) was attacked but superficially.5 Recent experiments have shown that a roast at 650 to 9000 C. converts the manganese of rhodochrosite to a form that is quickly dissolved by a weak SO2 solution.6 Introduction of smelter gases containing much as 5 per cent SO2 during such a roast would not add much to the cost of the operation, and might result in the formation of considerable water-soluble manganese sulpate.Another case involves a subsequent step in the hydrometallurgical process, namely, the formation of oxides of manganese with simultaneous evolution of SO2 by the heating of the MnSO4 produced by evaporating its solution.A third has to do with the roasting of zinc sulphide ores containing manganese as a preliminary to leaching. During purification of the solutions to be used for the electrolytic deposition of zinc the iron must be oxidized to make possible its removal. Manganese dioxide has been used for this purpose,7 and since manganese compounds are present in some zinc concentrates,8 it is of interest to learn what happens to the manganese in a zinc sulphide or on roasting, and what portion of the manganese in the roasted product might be available for oxidation."

Oct 1, 1930

By G. E. McElroy

This report discusses the construction and use of an all-pressure psychrometric chart in which the requirements of simplicity of appearance and absolute accuracy have been waived, to a certain extent, to provide for the rapid determination of psychrometric data and for the rapid solution of air-conditioning problems of major interest to the mining industry. Many mines in which air-conditioning problems are important are situated at elevations far above sea level and embrace great differences in elevation - in excess of 8,000 feet in certain mines - throughout their airflow circuits. Under these conditions, the effects of variations in the pressure of the atmosphere upon the physical properties of the mixture of air and water vapor of which it is composed are considerable and should be taken into account in the solution of problems. The simple types of psychrometric charts in common use, such as the Carrier, Bulkeley, Hill, and Goff (American Society of Heating and Ventilating Engineers Guide), are not generally suitable, in that they are drawn for a single barometric pressure - 29.92 inches mercury.

Dec 1, 1947

By Harry Dobroski

Communications with moving tracked vehicles in a rail haulage mine pose a difficult problem. These communications take place from dispatcher to vehicles or from vehicle to vehicle via the trolley line, which is a very poor communications line. As a result, deadspots and high-signal areas can occur anywhere along the line, or signal can decrease simply as a function of distance. An analysis is made of the trolley line as a communications line, and methods of improving its characteristics are discussed. Data from inmine experiments are presented, showing actual improvements in communications. Recent Bureau developments in new hardware are also discussed. These include an adaptive speaker control for existing carrier phones and a new generation of improved carrier phones.

By Paul T. Alexander

After evaluating preceding studies and designs of lightweight supports, ESD selected the all-hydraulic and the hydromechanical concepts for detailed design and fabrication. Further analysis and testing showed that the all-hydraulic design was economically justified and met all the crucial engineering, manufacturing, and design criteria identified during the evaluation phase. Following Bureau of Mines approval of the detailed design, four all-hydraulic support models were fabricated. Once functional and structural testing was successfully completed, 40 additional units were constructed and distributed for in-mine testing. The units were very well-liked by all three demonstration mines. The wide- spread interest in supports for seam heights greater than 8 feet led to expansion of the design data package. ESD designed four basic models to cover the new height range, but no hardware has yet been fabricated for the new design.

Jan 1, 1982

By Walter Pajalich

This Bureau of Mines report is a study of the organizational framework of the ferrous scrap industry, of the products produced, and of the factors affecting the consumption of ferrous scrap by the steel industry. Consumption data from 27 major iron and steel firms in the States of Illinois, Indiana, Iowa, Michigan, Minnesota, and Wisconsin during the period between 1957 to 1962 were grouped by type of iron and steel furnace production facilities to determine consumption pattern for various grades of scrap in comparison to ingot production, hot metal consumption, and home scrap generation. Grades of scrap affected by changes in scrap consumption were determined, and the pattern that emerged was analyzed. Correlation of scrap demand and its effects on scrap prices based on price of scrap receipts of No. 1 heavy melting scrap and No. 2 bundles in the Chicago area for the years 1957 through 1962 indicated that demand trends do not always affect the price of scrap, Past and present technological advancements in steelmaking processes are discussed, and their effects on the scrap industry are analyzed.

Jan 1, 1967