Search Documents

By Charles W. Briggs

The steel foundries of Germany were investigated for the purpose of ascertaining (1) the type and classification of steel structures produced as castings, (2) processing methods, (3) the mechanical properties of carbon and alloy cast steels, (4) the type and character of defective castings, (5) the appearance of castings, (6) research in steel castings, and (7) plant lay-out and equipment.

Jan 1, 1946

By James Westfield

Drilling for roof bolting has created a new dust problem for the coal-mining industry. Drilling is inherently dusty, and control of dust produced by drilling vertical or nearly vertical holes is much more difficult than control of that produced by drilling flat or down holes.4/ Also, the dust produced by roof drilling differs in composition from that produced by drill-fur, or cutting the coal face because it contains a significantly greater amount of free silica and therefore presents a greater potential hazard of silicosis. Roof bolting has been practiced successfully in the mines of the St. Joseph Lead Co. in southeastern Missouri for over 20 years, but it was not until 1947 and 1948 that large-scale roof-bolting experiments were conducted in coal mines.5/ Although the need for dust control in conjunction with roof drilling was recognized from the beginning, the development and acceptance of roof bolting progressed so rapidly during 1949 and 1950 that solution of the dust problem lagged behind other engineering phases of the technique.

Jan 1, 1951

By Robin B. McCulloch

No producing mines are in the study area. Sample results indicate the only resources in the study area are low grade phosphate deposits associated with Cuyama Phosphate Mine (fig. 1). Within the study area, are more than 21.4 million tons of inferred subeconomic phosphate rock resources which would be reserves at an 80 percent higher phosphoric acid price; weighted average grade is 4.84 percent phosphorous pentoxide (P205). About 17.6 million tons of similar grade are outside the area to the northwest. The South Cuyama Oil Field, adjacent to the study area (fig. 1), produces petroleum from the Vaqueros Formation which underlies parts of the study area. Oil and gas potential was evaluated by U.S. Geological Survey. INTRODUCTION Location, Size, and Geographic Setting The U.S. Bureau of Mines conducted a mineral survey of the Fox Mountain RARE II area (No. 5120) during the summer of 1981. The area was examined to determine the presence or absence of mineral resources and reserves, and to estimate tonnage and grade where possible.

Jan 1, 1982

By Galen G. Waddell

The Deep Creek zinc and lead mine afforded an excellent example of a relatively small underground mine operation that approached the low mining costs of large, highly mechanized mines. An open stope mining method incorporating sublevel benches and vertical long holes was used (fig. 1). Detailed descriptions are given on the exploration program, stope development, stoping procedures, and pillar removal. Pressure grouting was used to check the inflow of water and thus prolong the life of the mine. Statistics on mining costs and on electric power consumption, haulage from mine to mill, and milling costs are included.

Jan 1, 1963

By John C. Machisak

THIS CHAPTER of the Minerals Yearbook (Volume III) contains overall injury experience for coal mines, both anthracite and bituminous, coke plants, petroleum and natural gas, peat, and asphalt and related bitumens (native); metal mines, their metallurgical plants, including ore-dressing plants and primary nonferrous reduction plants and refineries; nonmetal mines; nonmetal mills; sand and gravel operations; slag (iron blast-furnace) plaints; and stone quarries and their related pants. Volume I of the yearbook contains a chapter showing injury experience and employment data treated separately by metal mines, nonmetal mines, quarries and their related plants, metallurgical plants (ore-dressing plants and primary nonferrous reduction plants and refineries are shown separately), nonmetal mills, sand and gravel plants, and iron blast-furnace slag plants. Volume II contains injury and employment experience in the fuel industries (coal, coke, petroleum and natural gas, asphalt and related bitumens (native), and peat. Injury and employment data are submitted voluntarily for the mineral operations through an industry canvass made by the Bureau of Mines, except for the coal industry, whose reports are mandatory. Information published in this chapter is the result of this canvass. Figures presented in this chapter for 1961 are preliminary except for anthracite, peat, coke, petroleum and natural gas, asphalt and related bitumens, and slag. These preliminary data, with the exception of bituminous coal, are a summation of reports received by May 31, 1962, from the operators showing their injury and employment experience. Estimations of injury and employment experience are not included in these preliminary data.

Jan 1, 1962

By R. A. Franks, G. F. Friel, J. C. Edwards, L. Yuan

The reversal of smoke products-of-combustion (POC) from a mine fire was determined in a mine section with the airway connectivity of an electrical Wheatstone bridge. Four diesel-fuel fire experiments with fire heat-release rates between 504 and 771 kW were conducted in the Safety Research Coal Mine (SRCM) located at the National Institute for Occupational Safety and Health’s (NIOSH) Pittsburgh Research Laboratory (PRL). Smoke reversal propagated upwind from the fire with significant leakage into the upwind diagonal airway and without causing a complete reversal of airflow in the diagonal airway. A control measure consisting of a brattice suspended half entry height from the entry roof was determined to abate the smoke rollback. Computational fluid dynamics (CFD) analysis of the smoke movement agreed with the measurements.

By Stephen C. Tadolini

The U.S. Bureau of Mines has developed ultrasonic measurement instrumentation capable of measuring strains and elongations on tensioned and untensioned mine roof bolting systems. This report evaluates the pulsed-phase-lock-loop and pulse-echo systems. The pulse-echo systems measure time of flight of a signal through the bolt. The ultrasonic instrument converts the measurement into elongations or stress. The most recent Bureau instrument development converts travel-time measurements directly into elongation, load, stress, and torque by simple data manipulation from the keyboard. Bolt preparation and instrument calibration are described in detail.

Jan 1, 1990

By F. A. Rutledge, J. J. Mulligan, W. H. Kems, R. L. Thome

"As a part of the United States Department of the Interior program for the development and use of Alaska raw materials, the Bureau of Mines is conducting an investigation of deposits f nonmetallic minerals accessible to the Alaska Railroad for use in building materials in the Alaska Railroad-belt area. The results of the investigations, to date, indicate that raw materials for the production of brick products are in plentiful supply as clay in the Anchorage area, as fire clay at Sheep Mountain, and as shale in the Healy Creek coal formations near Healy, Alaska.Shale for the production of lightweight aggregate or Haydite occurs near mile 67 on the Glenn Highway, and preliminary tests give excellent results. Physical tests are new in progress on commercial-size concrete building units made with this aggregate. Another shale deposit in the same formation was located at mile 16 on the Matanuska Branch of the Alaska Railroad, and preliminary tests give comparable results.Natural lightweight aggregate in tree form of pumice and pumicite occurs in Katmai National Monument and has been used with excellent results in lightweight-building units in Anchorage and Fairbanks. These deposits will be investigated in more detail by the Bureau of Mines during 1952.One small perlite deposit near Healy, Alaska, showed excellent expanding properties, and the product compares favorably with commercial perlites being used in the States for plaster and concrete aggregates. Additional investigation by the Bureau of Mines to delimit the known occurrence and, if possible, discover others were planned for the 1951 field season.The pumice from Katmai National Monument also was considered for use as a pozzolan in pozzolan-portland concrete. Tests by the Bureau of Reclamation indicate that the pumice sample submitted by the Bureau of Mines would be satisfactory in strength development but is not outstanding. Natural activity is good and is greatly improved by calcination at 1,4000 F. Water requirements and shrinkage also are satisfactory. However, the material is ineffective in reducing expansion owing to alkali-aggregate reaction; and, if reactive aggregate is used to make concrete, it would not insure against excessive expansion. An attempt will, be made during the 1952 field season to delimit pumicite deposits along the Alaska Peninsula more amenable for use in pozzolan-portIand concrete.Because the Railroad belt has such a rigorous climate, insulation for new construction is of prime importance. Luring the Bureau of Mines, investigation of building materials all samples were submitted for chemical analyses as possible sources of raw materials for the production of rock wool, one of the best insulation mediums. Four areas having deposits of the required constitu¬ents were located as follows: Anchorage area, with Potter limestone and argillite; Cantwell-Windy area, with limestone and shale; West Fork of the Chulitna River area, with limestone and agrillite; and Homer-Seldoyla area, with Seldovia limestone and Homer clay. It was planned to take bulk samples of these formations and submit them for testing during the 1951 field season."

Mar 1, 1953

By George K. Schenck

This Bureau of Mines publication describes and evaluates a Standard Industrial Classification (SIC) based end-use data system for minerals that is designed to link the demand for minerals to economic activity in commercial uses. The new data system is two-dimensional. The first dimension of technical product classes (TPC's) measures the consumption of minerals in major primary intermediate products. The second dimension measures the consumption of these TPC's in SIC end-use sectors in sufficient detail to identify the major determinants of demand for each TPC. Intercomodity comparisons are achieved at the level of SIC two-digit major groups. The methodology was developed so that all available sources of information from Government and industry can be utilized at minimum cost. This information will be supplemented with additional data to be obtained by modifying existing Bureau of Mines canvasses so as to elicit additional quantitative responses from mineral producers. The new data system is expected to improve significantly the ability to forecast demand for minerals, and provide an information base that would, for the first time ever, permit resolution of such questions as trends in substitution among materials and the intensity-of-use of materials in end-use sectors. For the 42 TPC?s identified in the report, data are available for the new system from current sources or, except for three TPC?s that require new canvasses, can be obtained by modification of existing Bureau canvasses.

Jan 1, 1982

By Renpei Yoda

An investigation was conducted to develop columbium alloys with e1evated-temperature strengths higher than those exhibited by more common commercial columbium alloys, and attention was given to improving the oxidation resistance and ease of fabrication. Additions of carbon, aluminum, and chromium were made to some columbium-base alloys, and their effects on workability, recrystallization, oxidation resistance, and mechanical properties at elevated temperatures were explored. The additions were made to take advantage of (1) solid solution strengthening, and (2) precipitation hardening. Three alloys displayed good high-temperature properties with relatively good oxidation resistance at 1,000° C, and tensile strengths from 26,000 to 32,200 psi at 1,400° C. When the properties of these alloys were compared with those of commercial alloys, B-66 and FS-85 (1),4 the outcome was favor-able for the alloys studied in this investigation.

Jan 1, 1967

By G. W. Jones

From evidence made available during the investigation, it was concluded that the first of a series of explosions occurred at 1:15 to 1:20 p.m. September 21, 1951, in an underground vault that housed pressure regulators on the gas-distribution lines that served Brighten. This explosion damaged the pressure regulators and permitted high-pressure gas to enter the distributing mains and individual-service lines. As a part of the gas-distribution system was not provided with means for protection against such excessive pressures, gas gained access to the interiors of many residences in this area and caused a series of disastrous explosions and fires, which took place during a period of approximately 2 hours after the initial explosion in the pressure-regulator vault. Two persons were killed in the first explosion in a residence, and a third person died of a heart attack attributed to the excitement that prevailed during the explosions and fires, Twenty-three persons were listed as injured. Forty-one residences were either destroyed or damaged - 11 by explosion and the remainder by fires, which developed as a result of gas leakage into residences. Fifteen residences were listed as "completely down" or "gutted." Unofficial estimates of property damage ranged from $1,000,000 to $1,500,000. In view of observations made and information obtained during the investigation, recommendations are presented in this report relative to the natural-gas distribution system in Brighton, which may be helpful in the prevention of similar accidents in this and other communities.

Jan 1, 1952

By A. D. Garman

This paper presents one of a series of digests of foreign mining legislation and court decisions which is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries . This interpretation of the laws of Uruguay has been prepared from the best available information in Washington, but is released subject to correction and amplification , if necessary , by the proper American diplomatic and consular officers to whom it is being referred through the courtesy of the Department of State .

Sep 1, 1930

By V. A. Cammarota

In this report, the effects of anode-production variables, such as aggregate coke sizes, pitch binder content, and baking cycle, were investigated. A small alumina reduction cell proved effective in evaluating anodes prepared from commercial materials and from lignite coke and pitch. Compressive strength was found to be the physical property most significantly influenced, but it did not appear to affect anode consumption. Specific carbon consumption, that is, the ratio of carbon in the anodic gas to carbon theoretically oxidized at the anode, was used as an index of anode consumption. It was found that an anode made with lignite coke and commercial pitch was very low in consumption; however, anodes made completely from lignite but by a different fabrication method showed high consumption and anode deterioration. Microscopic examination of anodes after electrolysis showed evidence of higher consumption at low current densities, and was useful in judging overall anode quality. Based on the physical properties of the anodes and their consumption during electrolysis, lignite can be a suitable material for anodes, provided the proper fabrication conditions are used.

Jan 1, 1970

By Jr. Smith

The equilibrium compositions of product gases for mixtures of air with methane, propane, or ethylene at and around flame temperatures are reported. For each hydrocarbon, compositions are given for five fuel-to-air ratios--two lean, two rich, and one stoichiometric--at five pressures, from 1 to 20 atmospheres, and at an ambient temperature of 25° C.

Jan 1, 1965

This manual provides instructions for installing, operating, and maintaining a protective canopy on the Joy Mfg. Co. shuttle car. These instructions are based upon actual installations made in the mine on two shuttle cars, model 21SC-2E. The parts list and engineering drawings for the protective canopy are included at the end of the manual. And a discussion of some alternative design concepts is also included. The manual can also be used for retrofitting other shuttle cars with similar protective canopies. Skilled mechanics can determine if the instructions hexein would he applicable to the other shuttle cars and can determine any necessary modifications if they are not.

Jan 1, 1973

By Kenneth H. Johnston

This report describes in detail three waterflooding projects and a pressure-maintenance project in Butler and Cowley Counties, Kans., that will be visited on the 1963 annual spring tour of the Kansas-Oklahoma Waterflood Association. Among the unique features of the projects are the flooding of five oil-producing horizons separately with injection water furnished by two water-treating plants. Discussion of the individual projects includes information on their early history, the source and treatment of the injection fluids, oil production decline curves, and the results of water injection on oil production.

Jan 1, 1963

By Ben Aleck

The objective of this program was to adapt Space Shuttle technology on high-performance spherical pressure vessels to cylindrical pressure vessels. Specifically, a cylindrical aluminum liner overwrapped with fiberglass filaments and prestressed by yielding the liner under a sizing pressure was to be replaced by a higher strength-to-weight ratio steel liner overwrapped with a higher strength-to-weight ratio filament. The steel was cryoworked stainless steel and the new fiber was Kevlar 49. In addition, the heavyweight ends of the aluminum liner were to be replaced by thin-walled domes which required multiple helix angle wraps for their support, in place of the single kite-string wrap from pole to pole of the aluminum overwrapped design. The use of cold swaging of tube-ends to form bosses, demonstrated on subscale development efforts, had not been achieved full-scale when the contract was initiated. Difficulties arose with the full-scale demonstration which were not solvable at the time with the designs and equipment available. hence, an unanticipated development was the finally selected method of making the 4-in.-diameter stainless steel liner with a single boss and no welds in an 0.020-in.-thick wall, from an 0.050-in.-thick, 13-in.-diameter disk. The demonstration vessel failed by leakage during the prestressing step because embedded oxides had formed flaws in the boss region. Such flaws have been avoided by proper temperature control during hot spinning. Hence, a new design was developed which weighs half as much as its recently developed predecessor. Funds ran out before adequate testable hardware was produced.

Jan 1, 1983

By C. A. Kumke

The Korean crisis and the cessation of Russian manganese-ore shipments to the United States in 1950 reemphasized the almost total dependence of the domestic steel industry on foreign supplies for metallurgical-grade manganese ore. In this emergency, Congress authorized the Bureau of Mines to undertake experimental mine and process development work on the known large reserves of low-grade manganese ore in the Artillery Mountains region in Mohave County, Ariz. The objective of the work was to obtain the basic mining and metallurgical data needed to make specific plans for initiating exploitation of the deposits within 3 years if high-grade foreign ore could not be obtained during the emergency. The manganese deposits of the Artillery Mountains region are in an area of about 25 square miles on the north side of the Bill Williams River in southern Mohave County. Lasky, of the Federal Geological Survey, has estimated reserves at 175 million tons of manganiferous material assaying 3.5 to 4 percent Mn. Although the man¬ganese occurs in various Tertiary and Quaternary formations as both bedded and fissure vein deposits, the more important syngenetic deposits are found in upper and lower manganiferous zones in the sedimentary beds of playa and alluvial fan origin that constitute the Chapin Wash formation.

Jan 1, 1957

By A. Visnapuu

Excessive noise and high vibration are inherently associated with equipment used in the mining, extraction, and processing of mineral resources. High vibration degrades structural components, often leading to catastrophic failure and loss of productivity, and excessive noise can result in permanent hearing loss. In order to foster efficient utilization of the Nation's mineral resources and minimize occupational hazards associated with mineral processing, the Bureau of Mines investigated the relationship between the microstructures of carbon and alloy steels and cast irons and their damping capacities (ability to absorb vibration). Researchers measured damping capacity and other properties and investigated the effects of carburizing, spheroidizing, and annealing. The investigators found that in carbon and alloy steels, rounded colonies of fine-grained pearlite in a ferrite matrix correlate well with low damping capacity. Steel microstructures that exhibit sharp-faceted pearlite in ferrite matrix and partially or fully spheroidized cementite in ferrite show considerably higher damping. In cast irons, the lowest damping capacity is associated with nodular graphite microstructure, and the specific damping capacity (SDC) increases as the graphite micro-structure progresses from nodular to compacted to flake. Predominant ferrite in cast irons is also associated with good damping. SDC data are presented for selected carbon and alloy steels and cast irons.

Jan 1, 1987

By J. P. McCullough

In 1943, the Federal Bureau of Mines began a program of thermodynamic investigations of petroleum constituents and related compounds. These systematic, long-range studies, which were conducted in the thermodynamics laboratory of the Bartlesville Petroleum Research Center and are still continuing, have resulted in a substantial quantity of data valuable to the petroleum industry and science in general. As separate phases of these studies were completed, the findings were promptly reported in the scientific press. During the past 16 years, 89 journal articles, giving the results obtained for individual compounds and small groups of related compounds, were published, mainly in the Journal of the American Chemical Society and the Journal of Physical Chemistry. In addition, members of the Bureau staff have contributed six chapters to specialized reference books. This circular, prepared in response to many requests, lists these 95 published papers, giving an abstract of the contents of each, as well as titles, authors, and literature citations. The journal articles are listed in the order of their preparation, which closely approximates the chronological order of their publication; hence, the item number to the left of each citation corresponds to the assigned contribution number. For the convenience of the reader, the abstract section is followed by a condensed bibliography, arranged alphabetically by senior author and keyed to the abstracts by appropriate contribution numbers in parentheses after the entry.

Jan 1, 1961