Search Documents

By Larry Mirabelli, David Lilly

In 1777, the French naturalist, Georges Louis Leclerc, Compte de Buffon developed a statistical technique to estimate the width between two parallel lines by randomly throwing a needle at the two lines and counting the number of times the needle intersected one of the two lines. By knowing the length of the needle, the distance between the parallel lines could be estimated. This analysis was named the “Buffon’s Needle Problem”.

Jan 1, 2008

By Tom Treleaven

The success of any blast is dependent on the accuracy of the blast design and the field controls used on the shot. This point cannot be over emphasized because when the geometry is not measured and/or field controls are not properly implemented, it can often have devastating effects on the final blast results. Thus drilling accuracy, tiont row burden control, explosive confinement, energy distribution, explosive selection, timing and structural geology become critical parameters in the design of successful blasts. Understanding the actual dynamics of the blast and why certain results were achieved is the fast step in optimizing a blast design. As stated by R. Frank Chiappetta, “Of all the blast monitoring systems available today, high speed videography still remains as the best stand alone instrumentation system for blast diagnostics.” Over the past years I have analyzed hundreds of blasts using either high-speed lowcams (500 frames per second) cameras or standard digital (30 frames per second). These analyses confirm, without a doubt, that shot geometry, in combination with structural geology, is the most important factor in overall blast results. Drilling accuracy is the single most important component in efficient blasting. Having equal mass associated with an equivalent energy is the basis in which blasts are designed. When drilling inaccuracy or borehole deviation occurs, not only is the energy unevenly distributed, but the basis of all design calculations becomes invalid. Over the past several years, quarry and mining operations have employed the use of boretracking measuring devices to measure borehole deviation and hole toe locations. In cases of operations using top hammer drills, it was discovered that the amount of deviation was significant and far greater than they believed they had. Set up error, improper drilling techniques and bit wear were some of the contributing factors. Through video anaysis of boretracked blasts, blast results were directly linked to drilling ..accuracy. The comparisons here took into account blast design, energy factors and hole sequencing.

Jan 1, 2000

By J. Mikhael Erekson, Connie Campbell Brashear, Brent Meins

Christmas morning 2020, an IED in an RV was detonated along an evacuated section of downtown Nashville, Tennessee. The blast damaged over 40 buildings, including AT&T’s Main Central Office and caused internet and cell outages across 1,200 zip codes for three days including the airport and EMS services. Published investigations by the ATF and FBI were inconclusive in determining the explosive composition and size. Video captured a large fireball that may indicate a fuel-air-mixture explosion which would create lower peak pressures than high explosives, but longer pressure duration and significant impulsive loading. Blast pressures were amplified by reflections in the urban environment bordered by the 8-story AT&T building and a row of multi-story historic buildings. Some structures had little damage as they were shielded from the blast pressure by closer buildings, and seemingly far-field structures contained damage from the pressure wave after multiple reflections and propagation through porous parking garages. Damage to the reinforced concrete frame AT&T building included snapped masonry ties, cracking and spall to the closest column, and vertical displacement of the elevator, even with the brakes applied. The historic structures directly across the street from the blast partially collapsed. Initial damage included complete failures of unreinforced masonry façades, broken timber beams, and uplifted roofs. Secondary, progressive collapse took place over months as the brick walls and weakened historic mortar could not resist typical wind and environment loads. One of the close historic structures was renovated in the 1990’s and structural retrofits to comply with building codes were required. The addition of steel columns and façade tie-ins improved survivability and it remained standing with a high percentage of the front brick intact. Generally, the observed blast damage was related to a structural component’s mass and flexibility. Internal timber framing was unscathed, but many steel studs required replacement. Glazing damage was observed several blocks away and many roof membranes were punctured by falling debris. Secondary damage from broken sprinkler lines and loss of environmental control often led to more costly repairs than the initial blast pressure damage. The proliferation of bomb-making knowledge leads to hundreds of bombings each year in the US. Building risk considerations should include explosive threats along with other hazards. ASCE structural standards and design manuals have been published to address these risks and may be useful guides for building construction.

Feb 6, 2023

By Dave Kay, Young-Suk Song

To meet the needs of South Korea's rapidly expanding economy, a large number of infrastructure projects are under way to improve transportation efficiency within the nation. These projects include high-speed rail links between major population centres and improvements to the road network. Being densely populated and geographically mountainous, infrastructure development in Korea requires a significant amount of tunnelling. Owing to the predominantly hard granitic nature of rock, drill and blast is the preferred method of tunnel advance. The Korean tunneller, however, faces the same pressures as those of his international counterpart in that both cost and production targets need to be achieved while meeting expectations of both community and regulator.

Jan 1, 2005

By William H. Snyer

A relatively inexpensive, very fast response photo-optic/fiberoptic system has been conceived, constructed and employed by Denver Research Institute (DRI) to measure charge breakout uniformity on the surface of a very large ANFO detonation. The new equipment and technique was coined OWL (observation without leads). Its unique design provides the ability to monitor or measure detonation velocities and/or detonation breakout characteristics without fiberoptic or any other direct contact with the explosive. This system has proven to be versatile and has been used to measure surface breakout simultaneity on large ANFO detonations, munition case breakout times and velocity of detonation (VOD).

Jan 1, 1990

By Douglas A. Anderson

Much progress has been made in understanding the forward process for blast vibration simulation: that is, how to create a resultant seismogram from an empirically determined seed waveform. What has not been successfully investigated to date is the reverse process: Determining the contribution of each borehole to the resultant seismogram. It might seem that these should be two sides of the same coin, but the reverse process is much more complicated. That is because the source, geological path, and receiver contributions must be unraveled and then dissected. If that can be done, a relationship can be developed between the seismic source properties and the explosive interaction with the surrounding rock. This paper presents a first step in the unraveling process, through analysis of blast seismograms using wavelet transforms.

Jan 1, 2013

By Maurice Hunter

The paper outlines recent design developments in the computerization of surface crawler drills for the quarry industry. It references the technology firstly developed for the underground mining and construction industry, where automation and computerization has been in demand for a number of years.

Jan 1, 2003

By Brad H. A Brown, J Paul Tidman

To design a blast, one must give consideration to safety, economics, geometry, geology, production needs, and a variety of other requirements. To compare designs requires the time to develop alternatives, analyze, and then improve on them. A number of tools are available to assist with the first set of requirements, however they are poorly integrated. SHOTPlus is a program to improve the efficiency of blasting operations, by combining measurement and blast design tools, and offers the user the time and means to modify designs and explore alternatives.

Jan 1, 1997

By John Vynne

Too often, a mine’s operations, including drilling, blasting, loading, hauling, crushing, processing, etc., are considered independent steps, rather then a continuous process. In fact, these are interdependent operations with each step in the process having an impact on subsequent operations. If the effectiveness of the drilling and blasting operations can be improved, they will impact the entire mining process. Some of the resulting improvements include: level benches on grade; fragmentation and diggability with the result being reduced loading times; haul cycles improvements; and the crushing and milling operations will be more efficient and less energy consumed. Thunderbird refers to this as “Drill to Mill” information cycle or process. This paper focuses on two of the technological enhancements Thunderbird has added to its drill monitors that allow the mines to impact the “Drill to Mill” concept. These enhancements are: incorporating global positioning satellites into drill monitors; and radio off-loading of data. Thunderbird is part of the Integrated Mining Systems (IMS) alliance. IMS offers the mining industry the most comprehensive line of monitoring and navigation products available today for mobile mine equipment. In addition to Thunderbird’s drill monitors and GPS systems, the product line includes: Fleet Management Systems for trucks and loaders; dragline and shovel monitors; GPS based navigation systems for shovels, dozers and other mobile equipment; and surveying systems. IMS uses common communication systems, operating systems, and hardware components in order to provide a truly Integrated Mining System.

Jan 1, 2000

By Robert Hopler

A blast caused the destruction of a bridge and loaded freight train and the death of three men, near Chattanooga, Tenn., on May 16, 1907. The blast and its disastrous effect has been described by Mr. Hunter McDonald, M. Am. Soc. C. E., in a paper read before the Engineering Association of the South and reprinted in the Proceedings of the Association for April-June, 1907. The excessive damage was so largely due to coincidence and wreckage of the bridge and train so complete that the incident is worthy of notice.

Jan 1, 2008

By Robert McClure, Frederic Leclercq, Ricardo Chavez

With significant vibration control and fragmentation challenges facing them, the CBS quarry (department of the Nord) successfully integrated a technical partner and mine to mill optimisation to deal with a difficult environment. For the last three years, CBS has been conducting a global production monitoring program similar to the mine to mill concept used in the mining industry. This concept consists of optimising the drilling and blasting while monitoring the effects on the downstream chain (vibration control, loading, hauling, crushing, plant output). Blast optimization is ensured by systematic control of the blast geometry (volumes, patterns, bench and face anomalies, drill deviation) and by the use of constant specific energy blasting. Constant specific energy optimises the work of the explosive in a blasting operation and, when combined with a high accuracy programmable electronic blasting system, reduces the impact of blasting on the environment and enhances blast performance. These techniques ensure consistent blasting results and hence improved site productivity. The improvements achieved have been identified thanks to an effective system designed to monitor the key production parameters.

Jan 1, 2007

By Travis A. Davidsavor, David A. Provost

A segment of high-pressure steel petroleum pipeline needed to be replaced on a hillside and beneath a waterway within an existing right-of-way containing multiple petroleum pipelines. The pipeline replacement required excavation of sedimentary rock to allow placement of the new pipe. As a result of an existing right-of-way limitation, steep slopes, and hard rock, blasting would be required as close as 7.8 meters (25 feet) from two operating pipelines.

Feb 1, 2020

By Travis Davidsavor, David Provost

A segment of high-pressure steel petroleum pipeline needed to be replaced on a hillside and beneath a waterway within an existing right-of-way containing multiple petroleum pipelines. The pipeline replacement required excavation of sedimentary rock to allow placement of the new pipe. As a result of an existing right-of-way limitation, steep slopes, and hard rock, blasting would be required as close as 7.8 meters (25 feet) from two operating pipelines. Existing pipeline company standards would have effectively precluded the construction of the replacement pipe by blasting rock. To facilitate the required construction and evaluate actual pipe stress during blasting to ensure pipeline integrity, a comprehensive evaluation methodology was developed by a team of pipeline, mechanical, geotechnical, instrumentation, and blasting engineers. A total of 60 strain gages were affixed to the steel pipe and seismographs were buried at the surface near the blasting area. Test blasting allowed pipe stresses with corresponding ground motion to be monitored. A conservative analysis approach evaluated individual peak strains and revealed that only small pipeline strains, and therefore stresses, were induced in the pipeline as a result of blasting. This evaluation allowed specific procedures to be developed to inform the blasting operation of maximum explosive loading and minimum charge distances. Additionally, this effort provided the pipeline operator with appropriate pipeline operating pressures during blasting activities to limit total stresses in the pipeline to be below allowable stresses imposed by code, regulators, and company operational limitations. Recommendations were developed to measure the blast generated ground vibrations with seismographs buried at the depth of the pipe, near the pipe, and limit the ground vibrations from blasting to 150 mm/s (6 in/s). If ground vibration intensities of 120 mm/s (4 in/s) or more were observed, additional engineering review is recommended. Finally, all blasting would be suspended and all activities reviewed at peak ground vibration intensities of 230 mm/s (9 in/s). The evaluation effort resulted in effective and efficient construction of the pipeline replacement and allowed the pipeline operator to better understand blasting induced stresses on their assets.

By Christian J. Sorensen, Christopher Armstrong, Andrew Matejunas

A team consisting of junior and senior mechanical engineering students at New Mexico Tech worked on the design of an explosively loaded vessel, with a maximum load of 15 grams (0.53 oz) TNT equivalent explosive. The main challenge presented was to meet the stringent sample positioning specification of 3 microns in two Degrees Of Freedom (DOF) and one degree of rotation in a third DOF. This is to accommodate precise sample placement in a tight x-ray beam, and to bring areas such as explosives/metal interfaces into magnified field-of-view photography. This presentation describes the process and design decisions to arrive at the final product presented to LANL in December 2014. Our engineering analysis techniques will be reviewed, including use of American Society of Mechanical Engineers (ASME) Boiling & Pressure Vessel Code (BPVC) Code Case for Impulse Loaded Pressure Vessels (ASME BPVC Code Case 2564-3). Also discussed will be integration of Hydrocode computer models with Finite Element Method analysis.

Jan 1, 2015

By R. Frank Chiappetta

A new blasting technique has been developed by International Technologies, LLC. to eliminate subgrade drilling, lower ground vibrations, improve fragmentation and reduce explosive consumption. The new technique utilizes a uniquely designed borehole plug, with a bottom hole air deck and a predetermined stemming mass on top of the plug. This combination is referred to as the Power Deck?. Single holes and full scale tests were conducted by Blasting Analysis International, Inc. (BAI) to determine how the system works, the mechanisms behind its success and the best design parameters to use for the given rock conditions. Results have shown reduced or eliminated subgrade drilling, ground vibration reductions of up to 33%, reduced explosive consumption by 16 to 25%, and improved fragmentation by up to 25%. This paper summarizes the methodology, field test setups, analyzes procedures and results for one series of single hole and full-scale tests which were performed in a Pennsylvania, USA quarry.

Jan 1, 2004

By John C. Brulia

The IME member companies, the ISEE along with its chapter organizations, the Federal, state and municipal regulatory agencies, and the industry consultants and suppliers have developed safety equipment, provided safety guidelines, promulgated safety-oriented regulations, and conducted safety training for blasting personnel in an effort to reduce explosives-related accidents.

Jan 1, 1994

By James L. Austing, Allen J. Tulis, Ronald Pape, Ronald G. Draftz

In a certain sense, the explosives industry began in the 13th century with the invention of black powder, which is an intimate mixture of sulfur, carbon black or charcoal, and potassium or sodium nitrate. For several centuries thereafter, black powder was the sole general purpose energetic material, serving as an igniter, propelling charge, bursting charge, and blasting agent. By today’s standards, black powder is totally inadequate for the latter three functions, but its use continues as an igniter for propellant charges because of its unique ability to ignite and burn under ambient conditions. The history of the development of black powder was reviewed by Rose (1980).

Jan 1, 1995

By Brent Coleman, Wade Hutchison

The Montgomery Bell Academy project is a parking garage structure topped by a soccer field. This project included expanding parking and moving the present tennis courts. The project is located adjacent to an affluent historic neighborhood that posed some special public relations challenges.

Jan 1, 2012

By W. J. Birch, R. Farnfield, S. Hosein, C. Johnson

Modern smart phones include accelerometers based on MEMS (Micro Electro Mechanical System) technology giving the possibility to measure both acceleration and orientation. The widespread use of such phones has driven technological development to such a degree that it is now possible to obtain a triaxial accelerometer unit, that also include signal conditioning and analogue to digital conversion, in a package smaller than 1 cm2 (1/2 sq.in) for a relatively low cost.

Feb 6, 2023

By John Vynne

BHP’s Navajo coal mine installed drill monitoring and high precision navigation systems on their three overburden drills during 2002 and 2003. Details of the DrillNav system hardware and reporting system will be discussed, as well as the significant benefits Navajo has achieved since the systems were installed. Navajo is not satisfied with the current results and plan additional upgrades to the systems. In addition, Navajo plan to integrate the data from their drill systems with data from other systems to achieve even greater increases in drill productivity and to reduce overall mining costs.

Jan 1, 2007