Search Documents

By Hirsch H. H.

Further discussion at the North of England Institute of Mining and Mechanical Engineers' general meeting held in Newcastle-upon-Tyne, 3rd June 1916, on the paper published in Trans. I.Min.E., vol.LI, 1916, p.61-71, comprised the author's written reply to comments at the April meeting

Dec 1, 1916

By G. Zhan, P. Mousset-Jones, G. Danko, J. J. K. Daemen, C. Mezei

Paper presented at the conference Risk assessment in the extractive industries, held in Exeter, 23-24 March 1994, and first published London: IMM, 1994, preprint volume. 18pp., 12 refs. (Originally entitled: Tunnel roof diagnosis using a robotic sensor test bed.) An integral roof diagnosis method is proposed to assist in assessment of risk regarding the stability of an excavation. A Robotic Sensor Test Bed (RSTB) is being developed for the characterisation of roof stability. The sensor test bed consists of a sonic/ultrasonic wave response sensor, a laser surface profiler and a surface temperature sensor. These sensors are mounted on an articulated robot manipulator for performing remote-controlled or fully automated diagnoses. A number of laboratory and field sonic/ultrasonic tests were conducted. A high-energy ultrasonic transducer and an impact device were used to resonate rock slabs. The fracture depths of the slabs were found to be inversely related to the measured resonance frequencies. The agreement between identified and actual dimensions was acceptable. Field tests also showed that loose rock on the surface can be clearly distinguished from solid formation by comparing their wave responses. The robotic laser profiler part of the RSTB was used to measure surface geometry. Different scanning methods are being developed to achieve the fastest and most precise measurements and to provide pertinent information about rock joints and major fractures

Dec 1, 1994

By R D. Lama, A Misra

One of the major factors restricting an increase in the productivity of a longwall mine is lower productivity obtained in a development panel. There has been a significant improvement in gate road development, particularly in mines requiring high density roof and rib bolting within 2 m of the face. Advance rates have increased from an average of 3 m to 5 m per shift in 1985 up to an average of 5 m to 10 m per shift in 1991. In mines at shallow depths with reasonably good conditions the increase has not been that significant. Advance rates have increased from an average of 7 m to 12 ni per shift in 1985 to an average of 12 m to 15 m per shift in 1991. Compared to the United States' (US) development rates, these are much lower. Extensive research work has been carried out to minimise cutting, wheeling, support setting time, and to optimise pillar length to achieve maximum advance rates. Pillar optimisation is very important in order to expedite adverse rates. This paper investigates various development rate technologies, both present and future, and optimises pillars to improve these dev elupment rates. Pillar optimisation is based upon time and motion studies conducted at mines in the Illawara region of New' South Wales, Australia, and the basic tools of arithmetic.

Jan 9, 1996

By G Williams

Discussing equipment, systems of work, the need for updated programmes of local seismic exploration, and developments within the South Wales coalfield.

Jan 1, 1993

By D. Large, M. H. Davies, B. Driedrichs, U. Matzander

Synthesis report on a project carried out under the EC-funded BRITE-EURAM programme. A prototype high-resolution electromagnetic system, based on the theory of controlled-source magnetotellurics, was developed. The electrical source field is fed into the earth by dipoles at preselected frequencies and a multi-channel receiver measures five electric and three orthogonal magnetic fields. Suitable mapping algorithms and spatial filters are applied to the data and a new technique permits calibration during measurement. The system was field tested over a blind orebody, at 250-550 m depth, in the Aguas Tenidas area of the Iberian Pyrite Belt. Ten lines totalling 12 000 m of profile length were completed in seven days and the orebody was identified. Tests in the Irish Midlands suffered from strong electromagnetic interference of cultural origin

Jun 21, 1905

By A. P. Whittlestone, J. D. Johnson, R. J. Pine, M. E. Rogers

standpoint. The effect on efficiency of collisions

Apr 1, 1995

By E Oktay, I Yusufoglu, C Kahruman

Powder and spherical pellets of MoO2 were oxidised under controlled conditions in the temperature range 674-791 K at oxygen partial pressures of 8.1-30.4 kPa. Weight increase during the reaction was determined by thermogravimetric analysis. It was concluded that the reaction is 0.6th order with respect to oxygen concentation and that the activation energy is 148 kJ/mole. In experiments conducted with powder, fast transfer of reaction heat to the gas phase created isothermal conditions, but the temperature of pellets rose by a maximum of 54 K at 674 K and 105 K at 791 K. The rise in temperature caused structural changes such as sintering and crack formation, which had a considerable effect on the reaction rate. The findings should be taken into account in the design of equipment and choice of operating conditions for roasting MoS2

Jun 21, 1905

By R. B. Scott, J. Hewitson

The paper investigates the historical information relating to spontaneous heatings which have occurred within the area from 1955 to date. From this information the seams most liable are identified and the location within the workings is enumerated, together with the possible reason for the occurrence of the heatings. Details are given of the precautions taken during development, working and withdrawal. Sampling procedures are outlined and the interpretation of the results is discussed. Reference is made to the various types of material and techniques employed in both preventing and combating heatings and examples are given of their relative cost and the operational experience obtained. Special observations are made on the changes in mining techniques and their influence on spontaneous combustion.

May 23, 1905

By D. G. Skinner, M. SC. Griffiths

"The natural difficulties associated with the size evaluation of dusts render absolute measurement difficult, or indeed, impossible. Assuming that the desirability of gravi­ metric sampling be conceded, it appears likely tha,t the most suitable means available for physical evaluation are the method of total turbidity measurement, to give a con­ ventional value for specific surface, together with microscopical examination, the great merit of the latter being that in the hands of an experienced operator, semi-quantitative discrimination between coal and other particles is possible.The pipette method, as modified by Fryer, probably-deserves more attention than it has received up to the present. Whatever method is used, it is recommended that in view of the lack of medical knowledge, as much information as possible should be obtained with reference to the total mass concentration, the surface area of the total dust,' and the mass and area of the particles below 5μ in size."

Jan 1, 1947

By C. T. Shaw

Fur a secure mineral supply position to be maintained in the Fiuropean Community there must be a supply of qualified people in the minerals industries. The education of the people required to run and develop these industries should be a priority in the community. This means that there should be a strong capability in mining engineering education. The mining engineering professors decided in 1990 to get together in a new Society to discuss the problems. The Society of Mining Professors/Societat der Berg-baukunde was formed at a meeting in Austria in October 1990. It is basically a F.uropean Society with a few member professors from outside Europe to keep the Society conversant with trends elsewhere. The objectives of the Society are to see that the mining universities in Fiurope maintain standards and produce enough mining engineers. The present membership of the Society and the work of developing a database of current courses is described. Working from the knowledge base developed, it will be possible to design a 'European' mining degree course. The problems which will have to be addressed have been identified and are described in detail.The paper finally goes on to discuss the other problems that universities are facing, the economic problems and above all the lack of students applying for mining courses across Europe. The help and active participation of the mining industry, if that industry still wishes to employ mining engineers, is identified as the only possible solution to those problems.

Jan 1, 1993

By H. R. Thorpe

A floating gold dredge operating in coarse alluvial gravels of the Grey River on the west coast of the South Island, New Zealand, generated high concentrations of clay and colloidal particles in the dredge pond, which entered the groundwater system. Sampling was carried out at depths down to 20 m and it was found that variation of the length of the flow path occurred because of the movement of the dredge towards the piezometers. The alluvial gravels, the suspended sediments, the groundwater system and the water chemistry were all studied. Sediment concentrations were found to be highly variable with depth, but the relative concentrations in the depth profile were generally consistent as the flow distance shortened. The sediments were extremely fine and travelled further through the gravels than predicted. Comparison of field results with the available theory of deep filtration in clean beds of porous media gives some basis for estimating the behaviour of fine sediments in other alluvial systems

Jun 19, 1905

By R. J. Pine

Procedures are described for the application of risk analysis or probabilistic methods to mining geomechanics. The methods are widely applicable to existing mine design models. Detailed examples are given of plane slope failure and of pillar design based on displacement-discontinuity stress modelling and empirical strength assessment. The modelling techniques assessed are the Latin hypercube sampling method, incorporated in a spreadsheet environment, and the general point estimate method (GPEM), programmed in TurboBasic. An example GPEM program listing is included. Both methods are very convenient to use. Probabilistic acceptance criteria for slope stability after Priest and Brown are examined and alternatives are proposed where output distributions of factor of safety are approximately normal or lognormal and output distributions of safety margin are normal. The reliability index is included as a useful measure of variability with proposed acceptance criteria.

Jan 12, 1992

By G. M. Zhao

The gasification of lump coke with CO2 was studied in a fixed-bed reactor. The effective diffusivity of the gas was evaluated from measurements of the reactivity of the lump coke, produced by BHP Steel in New South Wales, and from kinetic parameters that were determined from the reactivity of fine grains. The grain model of effective diffusion in porous media was adopted to express the gasification rate of the lump coke and was found to fit the experimental data well. The relationship between reactivity and textural characteristics of the coke was examined

Jun 18, 1905

By P. Mousset-Jones, G. Danko

Variations of the temperature and steam/moisture content of the air with distance and time are modelled for a single airway. The input for the simulation is an air temperature that varies with time, together with the moisture/steam content that results, for example, from a fire with a given distribution of heat and of fume concentrations at the beginning of the airway. The transport of heat and moisture to the surface of the wallrock is assumed to be simultaneous. Such multiphase convection may result in evaporation from the moist wall close to the fire and recondensation downstream. The modelling of this non-linear effect is a unique feature of the new simulation. A new analytical solution is used to calculate the conduction of transient heat within the rock mantle, which, in the event of a fire, is typically a short-term process. This allows for an arbitrary variation of surface temperature with time - unlike that permitted by the age function solution, which is limited to stepped temperature changes. An iterative numerical scheme that has recently been developed to simulate mine climate is used to calculate the coupled transient heat conduction and multiphase surface heat transport in successive length increments along the airway. To demonstrate the simulation procedure a numerical example is presented in which a fire with a given distribution of heat and fume concentrations with time is located at the beginning of an airway

May 1, 1991

By A. Z. Lang, D. A. Hall

After a brief description of the causes of spontaneous heating and of general preventative methods, a detailed account is given of occurrences of spontaneous heating in the Main Seam (locally known as the 5/4 Seam) at Westoe Colliery. This seam is about 12 feet thick consisting of hands of coal and shale, but only 4 feet 6 inches is worked because of the thickness os strata in water-bearing rocks and the worked section is selected on quality considerations. An advancing longwall face in this seam (2nd South) began to heat after working for six months and ultimately had to be abandoned. By adopting retreating methods and mining narrow panels it has been possible to extract this coal at an excellent rate of productivity. The system of goaf ventilation is important, because the use of a bleed road would have given rise to dangerous conditions in a goaf which of necessity would have contained fallen coal. Preparatory seals were prepared at selected sites so that, if necessary, a panel could be sealed off quickly; these seals are completed as soon as possible (within three weeks) of finishing a panel. A gas sampling system has been instituted which includes daily sampling on the face and in the goaf, and weekly sampling at the stoppings of all completed panels. The coal has now been extracted from this seam for three years without any further difficulties from spontaneous heating.

May 23, 1905

By R. A. Halatchev

A risk model for assessment of the uncertainty in the forecasts of the planned profit is developed. It is based on the selling price of the metal recovered from the ore and the production per shift of the excavators. These two critical variables characterise the economic and technical aspects of the mining venture. Time-series methodology is used to describe the behaviour of the economic variable, which improves the adequacy of the modelling. A hypothetical open-pit gold mine is used to illustrate the application of the model. Results obtained show that the model is a good alternative to sensitivity analysis in taking account of the stochastic character of the price of the metal recovered from the excavated ore and the production per shift of the excavators used. The model can be extended by the inclusion of new variables that have a probabilistic nature

Dec 1, 1996

By L. J. Barnes

The process for bio-remediation of sulphidic slag (BROSS) operates at 45 degrees C in a neutral (pH 7), aerobic aqueous environment in which sulphide in the slag is converted to sulphate. A two-stage version has been developed that involves quantitative chemical pre-oxidation of total sulphide to thiosulphate, followed by complete biooxidation of thiosulphate to sulphate. Ferric hydroxide, also produced, acts as a flocculant in the bioreactor effluent, concentrating heavy metal precipitates in the thickener as a sludge which can be returned to the smelter. The process has a high sulphate production rate and low acid and nutrient consumptions. Microorganism growth is the rate-limiting stage, requiring a minimum liquid residence time in the bioreactor of about 7 h. Although large quantities of oxygen are needed, sufficient gas mass transfer can be attained in an air-lift reactor. Products are an aqueous stream containing sodium sulphate with only trace levels of toxic heavy metals and a benign, toxic metal-containing sludge

Jun 18, 1905

By I S. Lowndes, K. Moloney

Diesel powered equipment is currently used extensively in mining and tunnelling operations around the world due to its mobility, flexibility and through selective application to enhance productivity. However, the increased use of diesel equipment has exacerbated the pollutant load (including heat, humidity, exhaust gases and particulates) placed upon the environmental systems of many underground operations. This expansion in the use of diesel equipment has prom pted researchers to evaluate m easure ment and control technology. This paper reviews the recent research conducted in various countries.

Jan 10, 1996

By S. A. Sayed, M. N. M. Ahmed, M. A. Doheim

The performance of a 12.7 cm hydrocyclone was investigated by considering the effect of design variables (diameters of the vortex finder and apex) and operating variables (pressure drop and solids content of the feed) at a medium feed solids concentration of mixed minerals. Cut-size was found to be the most important parameter in hydrocyclone design and operation. The effect of feed pressure in reducing hydrocyclone cut-size is less pronounced at medium feed solids concentration with a mixed mineral feed. The choice of vortex finder diameter and apex diameter becomes more sensitive at medium feed solids concentrations. The effect of feed solids concentration in increasing the cut-size becomes less marked at higher concentrations. Predictions of an empirical model were found to be in good agreement with experimental data. Comparison of results obtained from the model with those predicted by theoretically derived models showed the latter to be more promising, with the turbulent two-phase model giving closer agreement with the experimental data

Apr 1, 1995

By J. D. T. Capocchi, M. B. Mourao

The rate of reaction between iron oxides and carbonaceous materials, agglomerated as pellets, was studied experimentally by measuring the weight loss as a function of time. The effects of temperature, carbon type, inert gas flow rate, pellet size and additions (sodium. carbonate and Portland cement) were determined. It was shown that the value of the apparent activation energy can display large deviations under different experimental conditions; in the present work it was found to be 226.6 kJ/mol. The reaction with coke is slower than with charcoal, and the rate increases as the flow of inert gas in the reaction vessel decreases. Comparison of the rates for pellets of different sizes has shown that for small pellets the initial rate is faster but that it slows down at high conversions owing to the penetration of inert gas into the pellet. Additions of sodium carbonate and Portland cement increase the rate; sodium. carbonate promotes the catalysis of the Boudouard reaction, which is the slowest of the partial reactions. The increase in the rate with Portland cement is attributed to the release of water vapour

Jun 18, 1905