Search Documents

By A. Rod Kern, Michael A. McNicholas, Yaser Taheri

Deep foundations were required for construction of an 18,000 ft2 (1,672 m2) 4-story office building and an adjacent 23,750 ft2 (2,206 m2) 5-story parking garage in Queens, New York due to an existing uncontrolled fill layer ranging from 15-20 ft (4.6 - 6.1 m) in thickness beneath the building footprint. The geotechnical engineers for the project initially selected auger cast-in-place (ACIP) piles over driven piles to limit the impact of noise and vibrations on the surrounding neighborhood. Ultimately, drilled displacement piles (DDP) were installed since this method offered a more economical solution that would generate the required pile capacity with shorter drill depths and would also mitigate spoils volume. During installation of test piles by the geotechnical contractor retained for the foundation work, multiple unanticipated soil conditions were encountered that would adversely affect the constructability of the piles. The existing fill contained significantly more natural and manmade obstructions than expected and the underlying glacial soil became too dense to penetrate at shallower depths than anticipated. This paper discusses how these issues were overcome through pre-drilling and the use of detailed instrumented test pile data coupled with in-house engineering capability to proactively re-evaluate minimum pile lengths at any given location and keep the project on track. INTRODUCTION Geotechnical work in the New York City market presents soil conditions that can be highly variable and challenging due to the presence of uncontrolled urban fill placed over the native soils. Construction in this area can therefore pose many unforeseen challenges, even with detailed geotechnical analysis being performed at project sites. A case in point is a construction site in Queens, New York. The proposed site development consisted of construction of a 4-story office building with a footprint of 18,000 ft2 (1672 m2) and a stand-alone 5-level parking garage with a footprint of 23,750 ft2 (2206 m2), together with associated new pavements and utilities. The site is bordered by a mix of commercial buildings and residential properties on all sides. Depth of the uncontrolled nature of the fill extended up to 20 ft (6.1 m) below street grade. Given the significant cost associated with removal and replacement, deep foundations were recommended to bypass the unsuitable soils and support the structures at depth where good bearing material existed.

Jan 1, 2019

By Patrick J. Hannigan, Frank Rausche, Rozbeh B. Moghaddam

Large diameter open-end pipe piles are increasingly used as deep foundations to support heavy onshore and offshore structures. During the driving process, several factors such as subsurface conditions, hammer type, hammer efficiency, pile type, plug conditions, temporarily increased base resistance, and loss of shaft resistance have direct impact on the driveability of large diameter open-end pipe piles. In a uniform subsurface condition, the unit shaft resistance increases with depth. Consequently, more resistance is accumulated as piles penetrate to greater depths which results in higher driving resistance. However, according to the friction fatigue analysis, the greater the number of shearing cycles occurring on a soil segment along the pile shaft, the greater the reduction of its shear resistance. As a consequence, since upper soil layers are subjected to a greater number of blows than those at greater depths, they have a relatively lower resistance compared to what would be calculated with standard geotechnical analysis methods. As a result of this progressive and nonuniform loss of shaft resistance with driving, blowcounts tend to increase at a lower rate than expected from traditional analyses. This paper discusses one of the approaches to the driveability analysis with the geotechnical friction fatigue consideration. It also shows comparisons between predicted driveability obtained from wave equation analysis and field driving records. All analyses were performed for a 2.134 m (7.0 ft) diameter open-end pipe pile installed at a total depth of 192.90 m (554 ft). Two separate static resistance and wave equation analyses were completed for the case study presented in this paper: 1) Friction Fatigue analysis based on the recommendations of Alm and Hamre (2001), subsequently referred to as the FF model, and 2) Standard Driveability analysis based on soil set- up factors, hereafter referred to as the SD model in this paper. Results from analyses included the shaft resistance distributions compared to the result of the signal matching analyses determined from the pile dynamic measurement. Furthermore, predicted blowcounts were compared to observed blowcounts during the pile driving. The comparison analyses indicated a 54.4 percent resistance loss of the Static Resistance during Driving (SRD) due to the geotechnical friction fatigue corresponding to a 46 percent reduction in total resistance. The analyses also showed that average predicted blowcounts using the friction fatigue were 6.4 percent lower than measured blowcounts, whereas, the standard driveability approach showed 42.1 percent higher blowcounts compared to the blowcounts shown in the driving log values.

Jan 1, 2019

By Benjamin B. Buensuceso III

Crosshole sonic logging (CSL) is a popular quality assurance and quality control method used to examine the concrete quality of cast-in place deep foundations, though the evaluation of the results is subject to certain limitations. One such limitation explored in this paper is the occurrence of false positives, where signal anomalies indicated by CSL test results are not necessarily indicative of imperfections in the foundation that could affect its performance. A case study of false positives evaluated in CSL records in a major infrastructure project in Metro Manila is presented in this paper. A detailed desktop evaluation and results from complementary high-strain dynamic load testing and low-strain pile integrity testing were used to evaluate the significance of the suspected false positive signal anomalies from the CSL test results. Recommendations for the proper interpretation and evaluation of CSL test results in Philippine practice, given the method’s limitations and examples presented, are also shared.

Sep 8, 2021

By Yazen Khasawneh, Osvaldo P. M. Vitali, Mohammad Nassim

Wind turbines are subjected to complex form of cyclic loadings with variable amplitudes and frequencies. The cyclic loading and the accumulation of plastic strains with the number of cycles will result in degradation of the foundation soil stiffness. The foundation stiffness degradation will result in a shift (reduction) of the fundamental frequency of the wind turbine. Although this issue is recognized in the guidelines for wind turbines foundation design, no specific provisions are provided in the guidelines to consider the long-term stiffness degradation. In this paper, a practical procedure to consider the long-term cyclic loading effects on the stiffness of wind turbine foundations in cohesive soil is proposed. The procedure is based on 3D FEM modeling and reliable empirical methods to estimate the stiffness degradation due to the cyclic loading. Using the proposed procedure, the long-term performance of the P&H tensionless pier foundation with and without a reinforcing collar at the top of the pier is assessed. The numerical results demonstrated that the long-term performance of the P&H tensionless pier foundation with a reinforcing collar at the top of the pier is outstanding with negligible long-term degradation of the foundation stiffness.

Sep 8, 2021

By Reinaldo J. Villa, Joshua C. Adams

The I-395/SR-836/I-95 reconstruction project is an $818-million design-build construction effort that includes construction of viaduct, segmental and signature bridges in Miami leading into Miami Beach in Florida. Based on the load testing performed during the design phase, the design-build team determined that conventional driven pile and drilled shaft foundations were not feasible for support of segmental and signature bridges. Due to the weak limestone formation and successful use of auger cast-in-place (ACIP) piles in the Downtown Miami area on commercial developments, ACIP piles were selected as a foundation system to support bridges. This is the first time in history where the bridges will be supported by ACIP pile foundations in an interstate highway in the State of Florida. The design build-team worked closely with the Florida Department of Transportation to develop requirements for the load test program. The paper will provide an overview of the geotechnical data collected, results of dynamic/bi-directional load testing performed on test piles, data collected, installation of piles, and lessons learned. The load test program included a total of fifteen test piles with dynamic, bi-directional, and lateral load testing on 30 and 36-inch diameter ACIP piles and instrumented with thermal integrity profiling wires.

Sep 8, 2021

By Kevin R. Johnson, Matt Caskey, Bryan Plaskett

Working in urban environments presents unique logistical challenges beyond those typically associated with traditional geotechnical design and construction. These challenges can include constrained sites with limited access and laydown area, vibration concerns for adjacent structures, and the need to complete work within limited schedules. When challenging geotechnical conditions like variable bedrock elevations are present, the need to balance performance requirements with logistical constraints become the driving factor when selecting deep foundation systems. This paper focuses on the deep foundations used for a new elevated pedestrian bridge at a major health care facility in Tampa, Florida. In addition to the technical design requirements, the owner required a deep foundation system that could offer low vibrations, rapid production, and clean installation to limit impacts on their properties and the public roadway that separated them. The paper describes the project specific geotechnical and design conditions, describes Ductile Iron Pile design, and focuses on how installation of the system addressed the unique logistical challenges. In addition, the implementation of a full-scale load testing program to assess compression, uplift, and lateral design capacities is presented. This paper represents one of the few published references for Ductile Iron Piles on projects in the United States.

Oct 1, 2022

By Douglas R. Hardin, Stanley L. Worst, Joanna Mason

A challenging earth retention project presented itself in Washington, DC in the backyard of the historic House of the Temple (The Scottish Rite of Freemasonry, Supreme Council 33°). Located at 15th St NW and S St NW, a forty-foot-deep underground basement was to be installed adjacent to the existing Temple, a historic Carriage House structure dating back to the 1800’s and across a narrow alley from a four-story brick apartment building. The unique geology of the site included typical urban fill overlying a mixture of loose alluvial soils underlaid by dense marine deposits of the Potomac Formation. The clay, sand and gravel of the Potomac included nested boulders up to three feet in diameter. Design of the earth retention system accounted for ground conditions, installation methods and estimated movement of the system and adjacent structures. Anticipated ground water and unanticipated water from leaky sewers also proved obstacles to overcome during construction. Soldier beams were installed using a variable momentvibratory hammer to minimize disturbance to the historic and sensitive structures. Monitoring of the existing structures included both seismograph and optical targets during installation of soldier beams and as the excavation progressed. Micropiles drilled into the Potomac Formation were a part of the permanent foundation for the new structure. This local case history will delve into the details of the successful design, installation, and performance of an earth retention system and micropiles in a historic and highly congested urban environment.

Oct 1, 2022

By Shreya Vivek Hokam, Dr. A. I. Dhatrak, S. W. Thakare, Dr. Vivek S. Hokam

Construction in congested urban areas has necessitated tall and massive structures. In urban areas, it is common to construct underground structure nearby existing buildings. Selection of an appropriate support structure system to be implemented in the excavation in an urban area is heavily dependent upon the geotechnical conditions and safety of the surroundings and neighbouring structures. Urban Rail, popularly referred to as Metro Rail, has seen substantial growth in India in the recent years. More cities are experiencing the need for metro rail to meet their day-today mobility requirements. The metro structures involved deep excavation for foundations which induces the stresses and thereby alters the existing equilibrium and thus may affect stability of neighbouring structures considering safety point of view. Hence, design and execution of deep excavations become one of the important challenging tasks of any geotechnical engineer in the modern era. Further, it is important to control the ground movement in order to prevent the failure of excavations. This involves specialized foundation technologies, usage of sophisticated equipment and new methods in underground construction, safety and monitoring systems. In this paper the methodology used for protecting adjoining structures due to deep excavation for Nagpur Metro station is studied.

Sep 1, 2022

By Arash Khosravifar, Nason McCullough, Stephen, Milad Souri, Scott Schlechter, E. Dickenson

The results of five centrifuge models were used to evaluate the response of pile-supported wharves subjected to inertial and liquefaction-induced lateral spreading loads. The centrifuge models contained pile groups that were embedded in rockfill dikes over layers of loose to dense sand and were shaken by a series of ground motions. The p-y curves were back-calculated for both dynamic and static loading from centrifuge data and were compared against commonly used API p-y relationships. It was found that a significant reduction in ultimate soil resistance occurred in dynamic p-y curves in partially/fully liquefied soils as compared to static p-y curves. It was also found that incorporating p-multipliers that are proportional to the pore water pressure ratio in granular materials is adequate for estimating pile demands in pseudo static analysis. 1. INTRODUCTION Liquefaction-induced ground deformations can cause severe damage to pile-supported wharves and other waterfront structures. A common approach in analyzing the lateral behavior of piles against seismic loads is using the beam on nonlinear Winkler foundation (BNWF) or p-y spring analysis. One common p-y relationship for sand is the one proposed by the American Petroleum Institute, also known as the API sand model (API 1993). While the API sand model was originally developed for the static loading conditions, it is common to modify the API sand curves for the effects of cyclic loading. However, there is no consensus on how to modify the static p-y curves for the effects of liquefaction and pore water pressure generation in loose granular soils. In previous studies, p-y springs of piles in liquefying soils were back-calculated from case histories, centrifuge model studies (e.g., Wilson et al. 2000; Brandenberg et al. 2005; Abdoun et al. 2003), full-scale tests (e.g., Rollins et al. 2005; Chang and Hutchinson 2013), and numerical analyses (e.g., McGann et al. 2011). In general, these studies found the softening effects of soil liquefaction on p-y curves, as well as a hardening behavior attributed to the dilative response of the liquefied soil around the pile. However, these studies provide varying recommendations on how to modify the static p-y curves to capture this complex behavior. Some design guidelines propose softening the static p-y curves using p-multipliers (e.g., Caltrans 2012). Other studies propose an upward concave shape for p-y curves in liquefied soils (e.g., Franke and Rollins 2013; Chang and Hutchinson 2013).

Jan 1, 2019

By Frank Rausche, Scott D. Webster, Rozbeh B. Moghaddam

"Pile foundation driveability is a function of several variables such as subsurface characteristics, hammer type, hammer efficiency, pile type, and plugging conditions. One important phenomenon occurring during pile driving, and yet not well documented and published, is the friction fatigue, where a reduction of shaft resistance is observed as the pile is driven to greater embedment. This paper introduces current soil models developed for the assessment of friction fatigue, and further presents a comparison between predicted driveability obtained from Wave Equation Analysis Program (GRLWEAP) and field driving records. From a literature survey, and review of technical articles, a widely-used soil model known as AH-01 has been selected to analyze the friction fatigue concept. Using a WEAP software, two driveability analysis were completed using the standard approach with setup factors, and adapting the AH-01 model into the WEAP input file. Driveability predictions were compared to the driving records corresponding to a 1676-mm x 44- mm open-ended pipe pile with a total and embedment lengths of 180-m and 119-m, respectively. Results from analyses and the comparison presented in this paper provide further information regarding existing methods for the incorporation of the friction fatigue concept to the driveability analyses, and contributes to a better prediction of driveability of open-ended pipe piles. IntroductionDynamic measurements during pile installation provide more dependable information as compared to results obtained from predictive models used for design. Despite uncertainties associated with a specific project site and foundation type, measured data provides a reliable understanding of the soil resistance and its distribution throughout the length of the pile. Back-calculations or back-analyses based on a series of measured data from a pile driving process could help to obtain reliable models to better predict events related to pile installation process in spite of all variability related to fitted models. One of the widely-used analysis regarding pile driving during the design phase is the “driveability analysis” where capacity, blowcounts, maximum stresses in the pile element, and transferred energy from the hammer to the pile element are predicted using mathematical models along with a software. Such analysis requires relevant information regarding soil, pile, and hammer properties combined with a deep understanding of the level of impact each one of these properties could have on the analysis."

Jan 1, 2017

By Satyajit Vaidya, Rudolph Frizzi, Sandy Larimer

"This paper presents a case history in design and construction of a deep foundation system that included high-capacity open-ended driven piles constructed to support a high-rise building in Manhattan, New York. The project site is bordered by existing buildings, active streets, and critical public transportation infrastructure, which were considered in the new building’s deep foundation and seismic design. This paper focuses on driven pile foundation design and installation through relatively loose soil deposits. Unique design aspects included seismic design considerations, and pile splice design for open-ended steel pipe piles subject to significant uplift and lateral loading. Unique construction aspects included quality assurance of open-ended steel pipe pile splices, and uplift and lateral load testing of driven piles installed in close proximity to other foundation elements installed for the project.SITE CONDITIONS AND SUBSURFACE CONDITIONSThe project site is located in Manhattan, New York, and is bordered by existing buildings, active streets, and critical public transportation infrastructure that is located about 60 feet from the site. The existing sidewalk grades around the site are between about el 4 and about el 13; elevations are referenced to the North American Vertical Datum 1988 (NAVD88).Subsurface conditions at the site generally consist of successive strata of historic fill, former river bottom deposits consisting of compressible clayey soils, and medium dense to dense sand, overlying mica schist bedrock. A generalized subsurface profile is shown in Fig. 1. The historic fill stratum is about 10 to 45 feet thick, and generally consists of loose to medium dense sandy soils with varying proportions of silt, gravel, and miscellaneous debris such as brick, concrete, and glass fragments. The underlying former river bottom deposit stratum is up to about 15 to 20 feet thick, and generally consists of very soft to very stiff clay and lenses of very loose to loose sand. Medium dense to dense sand was generally observed below the historic fill and former river bottom deposit strata and overlying bedrock. Top of bedrock was generally observed at about 80 to 105 feet (i.e. at about el -75 to el -100), except in the southeastern portion of the site where the top of rock was observed as deep as about 140 feet (i.e., at about el -135). Groundwater levels typically ranged between about el 1.5 and el -0.5."

Jan 1, 2016

By Lu Yitan, Frances Badelow, Manish Tiwari

"Large ‘design and construct’ projects often present significant geotechnical risks. However, these also present significant opportunities for value engineering in design. These opportunities can be realised through systematic site investigation and close collaboration with the Contractor to dovetail the design solutions to suit construction methods. This paper presents a case study of a large infrastructure project in Singapore which involved design optimization of an earth retention system for a deep excavation in a constrained urban environment. The project also required installation of over one thousand bored piles in highly variable ground conditions - identified as a key risk. Systematic site investigation was undertaken to develop a reliable ground model. A detailed value engineering exercise identified opportunities for design optimization by changing the retention systems and construction sequence in some segments. An innovative low cost ground improvement method was used in some areas to reduce the forces on the retention system. An extensive instrumentation and monitoring plan was implemented for verification of design and to mitigate the remaining risks. This paper includes the lessons learnt on this challenging project, which are relevant to a wide range of construction projects.INTRODUCTIONSingapore has been rapidly expanding its underground Mass Rapid Transit (MRT) network over the past two decades. The Thomson-East Coast Line (TEL) forms part of this expansion and is 43 km long and fully underground comprising 31 stations. This paper describes the value engineering and design optimizations undertaken during detailed design of the earth retaining and support structures (ERSS) for one of the underground stations along TEL. The station, currently under construction, is up to 24m deep and 350m long. The edge of the station excavation is less than 10m away from the existing MRTviaduct. The proposed station is surrounded by high-rise residential and commercial structures, somewithin 2m of the excavation. Land Transport Authority (LTA) of Singapore imposes stringent technical and contractual requirements on MRT construction works to ensure high quality and safety standards. These include minimum requirements for embedment of retaining walls, groundwater control, additional site investigation, instrumentation and monitoring, and compliance to LTA’s Civil Design Criteria (CDC). Any deviations from the minimum requirements can only be approved by LTA after detailed calculations, analysis and field testing are completed and additional monitoring and control measures are proposed."

Jan 1, 1900

By R. Lee Wooten, David R. Shields, Darren D. Clark

"Borehole permeability tests that measure flow or head changes in boreholes located within seepage barrier walls are commonly used to estimate the in situ permeabilities of those walls for quality control and assurance. The current state of practice for estimating permeabilities from these barrier wall borehole tests is to use equations published by M. J. Hvorslev in 1951. Hvorslev’s borehole test equations model an infinite stratum of uniform permeability, which is not the actual condition for a test performed in a low permeability barrier wall located within a high permeability stratum. We examine and develop alternative equations based on line source analytical models, which more closely match barrier wall test conditions. We describe how these alternate equations can be used to estimate barrier wall permeabilities from borehole tests and compare the results to those obtained from the Hvorslev models. We also provide recommendations that consider differing upstream and downstream water levels.Barrier Wall Permeability Tests - State Of PracticeThe installation of seepage barrier walls has become more common in a variety of applications ranging from dams and levees to contaminated sites requiring retardation of groundwater flow. The types of seepage barrier walls and installation methods include soil-bentonite, soil-cement-bentonite, concrete, self-hardening slurry, geomembranes, and sheet piles, installed with various soil mixing, slurry-supported trench, and driving methods.Owners and contractors have used a variety of methods to evaluate the permeability of these seepage barriers. The following table lists commonly used quality control/assurance tests for evaluating the permeability of a seepage barrier."

Jan 1, 2016

By Wu Jian-tao, LI Guo-wei

"The Cement Mixing Pile (CMP) quality assurance assessment is an important programme in evaluating the efficiency of foundation improvement. Coring is the current specified method of quality assessment in China which has the shortcomings of long cycle, high cost and low efficiency. The field and laboratory test show that the regular cone penetration test can only detect maximum of 4m of effective detection depth in CMP. In contrast, the method of cone penetration test in the reserved hole can detect the quality continuously along the pile at any depth. The tip resistance of reserved hole penetration in the 7th day has good linear relationship with unconfined compressive strength in the 28th day. The slope of linear relationship decreases with the increasing of clay particles content.INTRODUCTIONThe method of Cement Mixing Pile (CMP) is often used to improve soft soil foundation in highway construction, with the major purpose of reducing settlements under embankments (Bruce et al., 2000),which is a form of what is known as the Deep Mixing Method (Bruce et al., 2013). The CMP technology spread quickly in China in the 1980s. CMP quality assurance assessment is an important programme in evaluating the efficiency of foundation improvement. Coring is the current specified method of quality assessment in China (China Academy Of Building Research, 2002). The method of Coring is perceived in some quarters that samples will provide lower strengths given the distress caused to the core during drilling and extraction (Bruce et al., 2002).The cone penetration test CPT can provide continuous measurements of the penetration resistance, sleeve friction at the tip of the probe, which has advantages of simple operation, low cost and high efficiency compared with coring. However, CPT tests have not been established to assess CMP in Sweden because of difficulties in maintaining verticality (Larsson, 2005). In Finland and Norway, however, CPT tests are commonly used (Halkola, 1999). One of the disadvantages of CPT is the tendency of the cone to steer out of the column (Porbaha et al., 2003). Darya Mokrousova (2010) states this tendency to deviate can be overcome by pre-boring and starting the penetration test from the base of the pre-bored hole. Sheng Haiyang (1999) found that probes may be deflected out, sometimes even at small penetration depths, and may not give a complete inspection of the pile. Liu Songyu et al. (2003) suggested that the Standard Penetration Test (SPT) is an effective way to evaluate the strength and quality of stabilized soil-cement columns. In general, Regular CPT can’t test the full length of CMP, and SPT still needed drilling which causes discontinuous detection. From the existing standard of China, core sampling compressive strength test is the main method, evidently, coring displays a longer test cycle, high cost and low efficiency. Therefore, an improvement of CMP quality assessment, by conjuring a fast and reliable detection and evaluation method, is necessary. The aim of this paper is to research the feasibility of using CPT in assessing the quality of CMP and presents an improved CPT method."

Jan 1, 2015

By Randy R. Williams, Brian W. Wilson, George M. Filz, Marina S. W. Li, Donald A. Bruce

"In-situ wet grab sampling and post-installation coring of soil-cement structures are typically carried out for Quality Control (QC) and Quality Assurance (QA) of deep mixing (DM) schemes. Wet grab sampling and testing is used to provide data to indicate that performance requirements are being met during production, in advance of coring, which typically occurs at 28 days or later, following installation. While unconfined compressive strength (UCS) tests from wet grab samples provide good production indicators, industry practice often requires that acceptance criteria of soil-cement structures be based on UCS results from representative core samples.This paper outlines the approach adopted for field sampling and QA/QC testing carried out in highly variable subsurface conditions at a site located in northern British Columbia (BC), focusing on postinstallation soil-cement coring and strength testing for an extensive deep mixing scheme. A discussion on suitable methods of coring soil-cement structures and appropriate selection of samples for testing that are representative of the in-situ soil-cement structures is provided. This paper also discusses the selection strategy adopted for verification of strength and modulus parameters used for design, providing spatial and time coverage, as well as the acceptance criteria implemented, and provides comparisons with published industry recommendations.BACKGROUNDAn extensive deep mixing ground improvement scheme was completed for the development of a Liquefied Natural Gas (LNG) Facility to be located in Bish Cove, BC, Canada. The deep mixing scheme was implemented to treat very weak native deposits in-situ to support two mechanically stabilized earth (MSE) walls up to 20 m (66 ft) high, and their associated bulk earthworks. Within the DM area, the subsurface conditions were highly variable, ranging from deep (up to 21 m (69 ft) thick) deposits of very soft to soft clayey silt to silty clay, overlying layers of dense to very dense gravelly sand to sand and gravel, to compact deposits of silty sand (up to 15 m (49 ft) thick), overlying dense sand and gravel. Bedrock was encountered beneath the granular deposits and generally comprised granodiorite with occasional andesite dykes."

Jan 1, 2015

By J. Racinais, P. Vincent

"In September 2011, Menard Oceania (MO) was engaged by Mac Mahon John Holland Joint Venture (MJHJV) to provide ground improvement solution for the $34bn Ichthys LNG development. With close to 400,000m2 of mangrove swampland set to be reclaimed and improved, this project was a great opportunity to showcase the technical, commercial and environmental benefits that Dynamic Replacement (DR) ground Improvement technique can provide. The ground improvement works involved complete design and construction for the Ichthys LNG site located at Blaydin Point on a low lying peninsula in Darwin Harbour. Dynamic replacement and stone columns technique were selected to treat intertidal mangrove mud to achieve required bearing strength, stability and limit settlement to an acceptable levels. The site is underlain by a 3m to 5m thick layer of highly organic mangrove muds with very soft shear strength ranging from 0kPa to 12kPa at depth. The site is exposed to daily sea water level tidal variations of up to 8m, which created significant constructability constraints and slope instability risks. This paper presents the design philosophy, the process involved in the selection of the construction methods, the site constraints encountered during the works and a review of the results achieved, quality control and post constructions performance.INTRODUCTIONInpex Browse, Ltd (Inpex) and its partner Total are developing the Ichthys gas field to pipe gas to onshore facilities at Blaydin Point on the south side of East Arm in Darwin Harbour. The proposed LNG plant consists of gas receiving facilities, 2 x 4.2Mtpa nominal capacity LNG trains, LPG and condensate production facilities, product storage and export facilities, a module offload facility (MOF), a flare pad (FP) and associated off plot facilities.The proposed on-shore facilities are located on extremely soft intertidal mangrove muds, therefore an appropriate ground improvement was required to achieve required strength and stability of site works and limit long term settlement to an acceptable level.Various ground improvement techniques were studied to select the most suitable for the ground conditions and site constraints encountered at the Blaydin point site. Dynamic replacement technique was selected for onshore section to improve soft mangrove mud to depths of 5.5m and Stone Columns (SC) technique was selected for MOF off-shore section to improve intertidal deposits to a depth of 2.5m.This paper presents DR design and construction works performed between December 2012 and August 2013 at Flare Pad Area."

Jan 1, 1900

By Danielle Nhanqulumanga, Pranith Bhatt, Snehal Patel, Khadeeja Priyan

The Bi-Directional Static Load Test (BDSLT) is a test that determines the capacity of piles when loaded under bi-axial static compression. In recent years the BDSLT has seen an increase in demand due to its safety, speed, and affordability. This innovative foundation testing method has been universally used over the last 50 years, however respective codes and standards have only been published within the recent years. Detailed test procedures and methodology are expatiated in the ASTM D8169 M-18 [1], and the IRC 78 2014 Clause 709.2.5. [2] These standards provide the minimum requirements for the execution of the BDSLT. In this paper we did a comparative study of both standards envisaging to bring attention to the similarities and discrepancies found therein, with an aim to highlight the impacts and challenges that differing provisions of each standard could pose on the conduct of the BDSLT. Discrepancies found have been explained on the basis of geotechnical engineering theories and relevant field occurrences observed by superior engineers. Additionally, we emphasize on the relevance of experienced engineer’s judgement when utilizing the standards.

Sep 1, 2022

By Filippo Maria Leoni, Alessandro Bertero, Gianluca Pianezze

"As part of the Southeast Louisiana (SELA) drainage program, designed by the U.S. Army Corps of Engineers (USACE) to reduce flood damages in the City of New Orleans and surrounding parishes through the construction of new pumping stations and better drainage canals, the SELA-22 project entailed the installation of a concrete covered canal along Jefferson Ave. and Prytania Street, in a highly urbanized portion of Uptown New Orleans, LA. The scope of the required soil improvement was to replace the soil between two parallel lines of sheet piles with a soil-cement mass to eliminate underseepage and provide structural support for the concrete culvert. The USACE selected the jet grouting (Jet Grout) technology for the construction of the bottom plug. The bottom plug is between 18 and 21.5 ft thick with a maximum depth of approximately 40 ft, for a total length of approximately one mile. The treated soil comprised soft clays and silts with occasional presence of sands. Project specifications required 100% area coverage, a 28-days unconfined compressive strength of 100 psi and hydraulic conductivity of 1x10-6 cm/s, to be verified by testing specimens from cored samples. The specialty geotechnical contractor proposed to accomplish the task utilizing their proprietary and innovative elliptical bi-fluid Jet Grout technology, and elected to perform a pre-construction bench scale laboratory mixing program to determine the most suitable grout mix features (i.e. binder type and proportions, binder content, etc.) to be applied in the subsequent field test and production stages. This paper will summarize and compare the results obtained from the different pre-construction and construction stages; interpretations of the data will be provided, along with general considerations regarding the effectiveness and significance of bench scale testing for jet grouting applications.INTRODUCTIONIn general, the effectiveness of the construction parameters in any ground improvement work depends largely on the physical and mechanical properties of the soil to be treated. Therefore, well designed laboratory and field test programs, aimed to disclose the interaction between the site-specific soils and the mixing parameters, are essential to achieve the desired end product."

Jan 1, 2016

By Michael Kynett, Francke Walberg, Richard Millet, Khaled Chowdhury, Mary Perlea

"Cutoff walls are the most common seepage improvement measure for levee flood control projects throughout California’s Central Valley. Cutoff walls are widely used because they can be implemented within an existing right of way in either heavily urbanized areas with limited access, or in high-value crop agricultural areas. The most commonly used seepage cutoff wall types are soil-bentonite (SB), soilcement- bentonite (SCB), and cement-bentonite (CB). Contract values for cutoff wall rehabilitation projects in the Central Valley range from several millions of dollars to hundreds of millions of dollars, and play a significant role in the reduction of flood risk in urban and rural areas. However, recentlycompleted construction of several levee improvement projects has shown limitations and inconsistencies among the commonly used technical specifications for construction of seepage cutoff walls. These limitations were evaluated by practicing engineers involved in different stages of cutoff wall design and construction. This paper describes the specification areas that typically generate design and construction issues. Recommended improvements to specifications are suggested to address these issues. The paper’s topics include: the applicability of the different types of cutoff wall materials and construction methods, quality control testing requirements, backfill gradation requirements, mixing procedures, and settlement criteria for backfill.INTRODUCTIONFlood control projects on the Sacramento and San Joaquin rivers in the Central Valley region of Northern California consist of a large system of reservoirs, bypasses, and levees. The thousands of miles of levees within the system were largely constructed and raised by local entities as need arose; this construction occurred prior to the development of modern design and construction techniques. The majority of these levees were initially constructed to protect land for agricultural development; however, a significant portion of these areas have become or will soon be urbanized. This urbanization has historically occurred in locations right up to the levee footprint. This expedient form of historical levee construction, when combined with adverse riverine geomorphology, urban development, and productive agricultural regions, has led to a levee systems with severe seepage performance issues in a real-estate-constrained setting."

Jan 1, 2015

By Frank Albrecht, Brian McCarthy

"The Ararat Terminal Station (ARTS) is located 190km to the north-west of Melbourne, approximately 1.7km to the north of Elmhurst Township in the Pyrenees region of western Victoria, Australia. The site occupies an area of approximately 7.2 hectare of farmland. The electricity generated by the Ararat Wind Farm is directed to the ARTS terminal station before being connected to the grid. The ARTS structural design includes more than 180 steel yard support structures, three 25m-tall gantry ‘A’ frames, three modular control room buildings, a precast transformer bund, precast fire wall structures and related foundation design. Innovative driven engineered glue laminated timber (glulam) piles in a cruciform shape were used to reduce the foundation construction time, cost and the amount of concrete used in the project. It is the first time that engineered timber piles made from farmed Australian pine trees have been used in a large-scale environmentally-friendly project. Durability of the timber was achieved by H5 treatment and the use of reinforced concrete pile caps to protect the cruciform timber piles at the ground line. A pile-driving sequence was developed based on field trials. The lateral load capacities of the piles were estimated using engineering principles and from full-scale tests in the field. This paper provides an overview of details of engineered timber cruciform piles, durability of timber piles, design information, pile construction procedures, pile-driving procedures, the testing protocol, test results and validation. The test results were compared with predictions from several methods. In addition, potential future applications of similar systems in other infrastructure projects, and opportunities for future improvements are discussed. The structural aspects of this project were presented in a previous paper at the World Conference on Timber Engineering in Vienna in August 2016. See http://wcte2016.conf.tuwien.ac.at/home/ for further information."

Jan 1, 1900