Search Documents

By Keith R. Vining

Solid fuel, usually coke or anthracite, is commonly added to ground iron ore fines in the pelletising process to reduce the amount of burner fuel required and the maximum firing temperature, while maintaining pellet strength and the productivity of the pelletising plant. However, the use of coke and coal contribute to the production of greenhouse gases (eg carbon dioxide) and are a source of NOx and SOx emissions. Utilising wood biomass / wood char is one methodology CSIRO Minerals is investigating as an alternative to coke and coal, as it is a renewable energy source that is very reactive, has a low ash content and the potential to reduce emissions of greenhouse gases from the iron and steel-making process. Previous work has established that charcoal can effectively replace coke in the sintering process (Lovel et al, 2005), and the following experimental work aims to demonstrate that it can also provide an adequate replacement for coke and coal in the pelletising process. The paper presents the results of an experimental testwork program comparing the behaviour of fired pellets containing traditional solid fuels and charcoal. The physical properties of the pellets are compared in terms of their compressive strength, tumble and abrasion indices and the reduction properties. A qualitative assessment of the pellet microstructures is also presented.

May 1, 2007

By Brad Hewitt, Jeff Belke

"Murrin Murrin Operations has not had a successful beginning. Numerous reliability and operability issues many of which are the result of design decisions have been addressed through mechanical and operational changes and the CCD circuit is no exception. Four design aspects of the CCD circuit that have caused and continue to cause operational problems are:1. the inclusion of solution neutralisation gypsum in the CCD circuit feed which was designed solely for HPAL residue without proper investigation of its impact on the achievable underflow density and resulting wash efficiency;2. the decision to construct the thickener base from thickened solids;3. the lack of redundancy in the overflow, underflow and tailings pipe work; and4. the lack of thickener operational flexibility in the central rake-lift and feedwell dilution system.In November 2002, the lack of operational flexibility in the rake-lift and the feedwell dilution system through mechanical modification as follows:•, CCD1 has a modified rake mechanism that now allows central vertical lift of 600 mm;•, CCD1 has forced dilution using the Outokumpu Turbodil® technology and replacing the E-Duc® technology of Eimco;The decision to install, the installation and the results of the CCD1 rake-lift mechanism and feedwell dilution system are discussed in this paper. The installation was justified on improved operational robustness and an increase in the in the underflow density of 1 per cent (per cent w/w). At approximately the same time process modifications in the solution neutralisation circuit were implemented and these changes altered the rheology of the slurry reporting to CCD1. Since the modifications to CCD1 and the solution neutralisation circuit, the CCD circuit has averaged a 2 per cent improvement in the circuit underflow density.The CCD1 modification was completed on time and mechanically has performed well. From a risk point of view, the central rake-lift and Turbodil®dilution system add a degree of freedom and robustness to CCD1 operation that has extended the range of operational confidence. In this respect, the modification has been a success and is complementary solution neutralisation improvements."

Jan 1, 2005

By Corinne Boone

CO2e.com, LLC - launched in November 2000 - aims to be ?the global hub for carbon commerce.? CO2e.com is a subsidiary of the Cantor Fitzgerald Group, one of the world?s leading brokerage firms Recent Investor in CO2e ? Mitsui & Co. Alliance with Cantor Fitzgerald Environmental Brokerage Services Group (CFEBS) Offices in London, Toronto, Tokyo, New York, San Francisco, Los Angeles, Connecticut, Houston Primary Goals/Benefits of ET § Goals of Emissions Trading: ? Permit Industrial Growth/Expansion ? Promote Economic Efficiency and Flexibility in Meeting Air Pollution Standards § Benefits of Emissions Trading: ? Enhance Air Quality w/o Economic Stagnation ? Encourage Development of New Technology ? Foster Most Efficient Use of a Limited Resource -- Clean Air § Contributes to Sustainable Development and objectives of UNFCCC, Kyoto Protocol?.

Nov 1, 2002

By K. Lundholm, M. Andersson, L. Nevatalo, Å. Holmström, L. Hedström

"Several copper deposits have the arsenic bearing minerals enargite (Cu3AsS4) and tennantite (Cu12As4S12). Since this mineral contain both arsenic and copper, it is not possible to remove the arsenic by selective flotation. Partial roasting is a method to clean the concentrate from arsenic and thereby produce a suitable raw material for the copper smelter. Also mercury is commonly found in copper bearing minerals. In the partial roasting process both arsenic and mercury are volatilized, while part of the sulphur is used as energy during the roasting. This gives a calcine suitable as feed to a smelter, much like an ordinary copper concentrate. A typical analysis of calcine would be: S content 18–22%, As content below 0.3%, Cu content – not affected, grain size – not affected. However, if the concentrate contains mercury, the mercury will be volatilized during the roasting process. This will lead to very high mercury contents in the subsequent process of sulphuric acid, unless the SO2-rich process gas is pre-treated by the Boliden/Norzink process that recovers mercury as calomel, Hg2Cl2. The volatilized arsenic in the gas phase can be recovered either by dry or wet methods. However, one problem is that arsenic also contaminates the fine grained calcine dust that is captured downstream in the gas cleaning system. The calcine dust contains valuable metals such as copper, gold and silver that needs to be separated from the arsenic. The ultimate aim is to stabilize the recovered arsenic as a compound with minimum impact on the environment and recover the valuable metals. By using wet recovery methods it is possible to selectively precipitate copper, gold and silver as sulphides while arsenic is kept dissolved in the liquid. The precipitated metal sulphides can be mixed with the calcine and sent to the copper smelter. The dissolved arsenic is sent to effluent treatment and is further treated in Outotec ferric arsenate precipitation process, where arsenic is precipitated as the stable compound basic ferric arsenate, formula FeAsO4·xFe(OH)3. All concentrates containing arsenic are unique and the process design of a roaster plant must be based on relevant process data. The process data is collected during tests in lab scale and pilot scale, where the influence of critical process parameters on the quality of calcine is studied. The ability to run tests both in lab scale and pilot scale is crucial to the development of the correct roasting process. Outotec is well equipped for this."

Jan 1, 2014

By Ian D. Pirie

Presentation outline ?Project location ?Geology ?Resources and reserves ?Results of the FEED study ?Social and environmental considerations ?Project path forward

May 1, 2010

By J. H. Archibald

"IntroductionShot-saws are used for sawing rock throughout the dimension stone industry especially in granite quarry mills. Shot-saws, as currently designed, have an inherent wear problem which leads to slow cutting rates and repetitive blade changes which consumes much time. Because the saw blades are made from steel the abrasive shot used with them is limited to a certain hardness which effects the over-all efficiency of the sawing operation. Suggestions are made toward optimization of blade design and the sawing process. Blade DesignA common steel blade design is shown in Figure I. Note the perforations in the blade. These perforations or holes in the blade serve two or three purposes. The most obvious reason is to allow the abrasive shot a pocket in which to collect at the bottom of the blade, so that it can be distributed from these pockets into the cutting zone underneath the blade. The abrasive is fed to the saw in a slurry and usually comes in from the top. The blade must then cut a kerf wider than itself in order that the abrasive grains have a path leading from the top of the blade, down along its sides, and finally reaching the pockets and cutting zones. This circuitous path followed by the abrasive leads to side wear on the blades and high friction which can lead to blade buckling in severe cases. However, the fluidized path of the abrasives down the sides of the blade serves another purpose which is a positive gain if conditions are properly controlled. The abrasive slurry interacts with the perforations of the blade, the blade itself and the rock. This gap and the perforations in the blade, which are fluid filled, are sites of constant shearing motion. Eddy currents form in these gaps and pockets which tend to stabilize the blade by setting up balanced hydrodynamic forces which otherwise might not form in a non-perforated blade. A stable blade produces a more uniform cut in the rock. The third and final reason for the perforations are to allow the blade to wear in such a fashion that new pockets are always being formed and, consequently, new cutting surfaces between these pockets are also formed."

Jan 1, 1993

By Y. X. Zhao

This paper briefly describes the characteristics and induced factors of coal mining bumps based on the investigation of recent bumps accidents occurred in China. According to the theory of non-equilibrium thermodynamic and dissipate structure, the process of strain energy accumulation and dissipation in the ?Coal-Surrounding Rock? system (CSRS) is discussed during the preparation of coal bumps. In addition, a series of experiments are conducted to analyze the relationship between bump-prone property and micro-structural characteristics of coal. The process of coal bumps induced by propagation of fractures and deterioration of coal mass properties are also analyzed systematically.

May 1, 2009

By K. Zenger, J. Kaartinen, J. Huuskonen, S. Torttila, S. Lähteenmäki, J. Pietilä

"Pyhäsalmi Mine in Finland has a long history of continuous process development. The concentrator processes Cu-Zn-sulphide ore with high recoveries. An on-line flotation simulator has been developed to maintain and further improve the flotation performance. Consisting of a flotation kinetic dynamic model, and interconnected with process control software, the simulator can be used for training new control room operators in various scenarios. For daily operation, the model parameters are continuously adapted to take into account the changing process conditions. On-line simulator tracking the process can provide the process operator new information in several ways: a) values of unmeasured process variables are obtained by displaying the corresponding simulator values, b) predictions of future process states and outputs are calculated and displayed, c) information of changing process parameters can be used as an indicator of e.g. change in the processed ore type. This paper describes the adaptive simulation system and its usage at the Pyhäsalmi concentrator.IntroductionPyhäsalmi massive sulphide orebody is located in central Finland. Operation of the mine started in 1962 and it is currently producing copper (Cu), zinc (Zn) and sulphur (S) concentrates. The concentrator control and optimization system has a long history of successful continuous development during the past decades (see e.g. Huuskonen & Moilanen, 2010). An on-stream analyzer has been a part of the automatic process control since 1968 (Lähteenmäki, Miettunen & Saloheimo, 1999). First control algorithms based on a flotation mathematical model were developed in 1971 (Koivistoinen & Miettunen, 1985). In 1990’s the development of a froth machine vision systems started (Kaartinen, 2009; Kaartinen, Roine & Hätönen, 2009). More recently Pyhäsalmi Mine Oy has been involved with several national development projects dealing with particle size distribution measurements (Kaartinen & Tolonen, 2008), spectral analysis of flotation slurries (Haavisto, Kaartinen & Hyötyniemi, 2008), and dynamic simulation of flotation processes. The latter topic is further elaborated in this paper."

Jan 1, 2015

By Sydney C. Mifflen

COAL MINING, with its some 15,000 employees, is directly responsible for the livelihood of one-fifth of the population of the Province of Nova Scotia and indirectly so for that of possibly another fifth. Deposits of coal are known and worked in four counties of the Province, from which is being produced yearly tonnages as noted below: Cumberland County 750,000 tons Piccou County 400,000 tons Inverness County 100,000 tons Cape Breton County 5,250,000 tons TOTAL FOR NOVA SCOTIA 6,500,000 tons Production in Cape Breton county is entirely from the one source, the Sydney coalfield, and not only is this field the most important in respect to output, as is disclosed above, but it is also the largest presently known deposit in the Province and holds the greatest tonnage yet in reserve for future mining. In the light of the above more or less generally known facts, it is trite to remark on the importance of the Sydney coalfield in the internal economy of the Province. On the other hand, not nearly as well-known nor as frankly recognized is its significance in the national life of Canada, for from this field is produced not only 80 per cent of the Nova Scotia coal but over 40 per cent of all coal mined in the Dominion. Another noteworthy comparison can be made from the fact that the Sydney field contributes 22 per cent of all the bituminous coal consumed in Canada, the remainder being made up of 7 per cent mined elsewhere in Nova Scotia, 27 per cent from other parts of Canada (British Columbia and Alberta, principally), while the remaining 44 per cent is imported, practically wholly, from the United States of America.

Jan 1, 1941

By Walter Smith

Environmental Quality Committee ?EQC was created in 1995 to facilitate dialogue between industry and northern communities and help build the understanding of the industry in those communities. ?EQC is made up of representatives from 32 northern communities. ?Meet regularly with Cameco to discuss on going and new projects. ?Tour mine sites on a yearly basis.

Nov 1, 2011

By A. Sheikh, S. Hardcastle

"Various methods of leaching are being used by Denison Mines Ltd. Uranium Operations. This study was designed to investigate the flood leaching operation of two parallel inter-connected stopes contained by pressure bulkheads. The teaching muck piles, created from large scale uppers production blasts, are aerated by compressed air lines laid beneath the pile prior to blasting.A SFr, tracer gas, injection technique has been employed to determine the post-blast integrity of the single-ended air distribution system. SF6 was injected into the compressed air line feed to the stopes and collected at borehole exhausts from the stopes in grab-sampling bags. Analyses of the air samples were performed with a gas chromatograph.The system was designed to give a sufficiency of oxygen to sustain bacterial activities used to enhance the leaching recovery in the muck piles. The results obtained indicated that there is a minor anomaly in the distribution system that may not be critical to the operation. Compared to an idealized case, the over-all efficiency of aeration throughout the muck is estimated at over 85%."

Jan 1, 1988

By John D. Godfrey

Geological mapping on the Canadian Shield in northeastern Alberta outlined severalgranitoid rock massespotentially suitable as building stone. A particularly attractive prospect, the Chipewyan Red Granite, was subjected to an aerial survey and ground check. The petrologic and fracture characteristics critical for quarrying and use as a building stone were assessed in the course of detailed mapping at two of the most favourable sites. The extension of good rock was tested to shallow depths at one site by shallow diamond-drill coring. , The Chipewyan Red Granite displays a warm red colour, medium grain size and fairly massive texture, and takes a good polish. Deleterious geologic features studied in outcrop and subjected to structural analysis included regular joint systems, quartz veins, pegmatite dykes, basic shear zones and fault zones. Many of these key geologic features are systematic and hence predictable for stone quarrying purposes; other features, such as irregular fracelM tures, are non-systematic and arefar less predictable. The megascopic structural features studied show similar preferred orientations which appear to be collectively related to the tectonic history.

Jan 1, 1979

By A. Ignatieff

"Demonstrations of Automatic Coal Burning EquipmentAT THE 1951 and 1952 Annual Coal Research Conferences sponsored by the Dominion Coal Board and attended by delegates from the Dominion and Provincial governments as well as industry, the importance ,of encouraging the co-operative interest of Canadian coal and equipment industries in •promoting the use of equipment types best suited to burn given Canadian coals was emphasized. It. was suggested that this idea •be enlarged upon at forthcoming C.I.M. meetings that would be .attended largely by coal mining engineers.With this in view, a Domestic Heating Forum (1) was featured in the Coal Division programme at the 1951 Annual Western Meeting of the Institute in Calgary, and a much more ambitious programme, highlighted by live demonstrations, was •staged at the combined Annual Western Meeting and Fourth Meeting of District 4 held in Winnipeg in October 1952.With the excellent co-operation of a number of equipment manufacturers and coal companies, and with facilities kindly provided •by the University •of Manitoba authorities, burning demonstrations were• arranged in the Agricultural Engineering Building, on October l 7th. These demonstrations were a fitting sequel to the Coal Division sessions held in the Royal Alexandra Hotel on October 16th, at which the combustion of coal was specially featured in a series of papers by prominent Canadian and United States specialists.The primary purpose of the demonstrations was to •show that all coal, regardless •of rank, can be satisfactorily used provided that proper application is made with equipment suited to its purpose."

Jan 1, 1953

By E. C. Keeley

THE property of Buffalo Ankerite Gold Mines, Limited, is in Delora township, Porcupine area, Ontario. The southwestern part of the property is ground formerly owned by Marbuan Gold Mines, Limited, which was acquired by Buffalo Ankerite in January, 1936. Until 1938, the Ankerite (or North) mine and the Marbuan (or South) mine continued as separate operations, each developed through a surface shaft and winze to the 1050 level and each having its own mill. This meant high hoisting costs, which, in 1936 and 1937, amounted to 36 cents per ton. In 1938, the underground workings of the two mines were connected on the 1050 level, and ore from both mines was hoisted at the main, or No. 2, shaft of the North mine, location of which is shown in Figure l. This shaft was discontinued at a depth of 1150 feet because, owing to the soft nature of the talc (serpentine) rock in which it was sunk, it had to be concreted throughout, and also because of its great distance--1,100 feet and 1,400 feet, respectively-from the North and South orebodies.

Jan 1, 1945

By R. Mohan Srivastava

"The goal of estimation is considered in the light of decision analysis. A simple example reveals the essential elements of decision-making in the face of uncertainty. A second example shows that these elements are also key features of many mining decisions. These two examples cause us to revive an old probabilistic notion that the goal of estimation should be to quantify what is unknown. The conditional probability distribution provides the complete statement of one's uncertainty. Once the conditional probability distribution has been established, one should retain as an estimate the value which minimizes some objective loss function. A third example shows how the ""best"" estimate depends on the chosen loss function. Current practice is almost exclusively based on the least squares method, which assumes a loss function which penalizes underestimation and overestimation equally. This is unfortunate not only because symmetry is an unrealistic assumption but also because mining offers a rare opportunity to state the loss function directly in terms of profitability. Both the theoretical framework and the practical tools exist to allow us to reconsider the conventional notion of the ""best"" estimate. IntroductionThis paper looks at estimation in the mining industry from the point-of-view of decision analysis. Virtually all decisions depend on estimates since few of the important parameters are ever known exactly. In this paper we will be referring mainly to the estimation of ore grades, though the approach discussed here is generally applicable to any decision in which relevant information is uncertain.In the first section we look at a very simple example of decision-making in the face of uncertainty. We will then tum to a mining example and see that the essential features of the simple example still pertain. From these two examples it will be clear that the decision analysis approach rests on two key concepts: the conditional probability distribution and the loss function. A third example demonstrates how different loss functions produce different ""best"" estimates from the same conditional probability distribution. In the final sections we willexamine the current practice of estimation in the mining industry. Though the tools for estimating the conditional probability distribution already exist, a change in the way we think about ""best"" estimates is needed. Very little attention is presently paid to the loss function even though it is readily available in many mining applications."

Jan 1, 1987

By L. Vollert

In-situ recovery of metals is presently experiencing a revival not seen since early applications in amenable copper oxide deposits, uranium and generally applications where neither, porosity and permeability, nor process chemistry have been prohibitively difficult. With ever decreasing grades in current mining operations or Greenfields projects and ever increasing capital and operating costs, in-situ recovery is looked to as the processing option that will both unlock these deposits as well as potentially derive revenue from mineralised waste remaining in the ground once traditional mining and processing methods become uneconomical. In-situ recovery is also being looked to as a mining method that minimises the environmental impact sustained in the application of traditional energy and water intensive mining and processing operations where millions of tonnes of ore are mined from the earth, processed on surface and then disposed of in both waste dumps and tailings facilities. The key challenge facing companies like Newcrest is that these low-grade deposits or remnant mines are generally hard rock applications that require costly methods to liberate the valuable minerals. A further challenge includes identifying suitable chemistries that both facilitate the economic recovery of gold and copper and that may be considered environmentally acceptable. This paper presents a desktop study whereby the issues of access creation and chemical extraction are discussed and evaluated with a view to driving future research in the area and unlocking this application as a real processing option. INTRODUCTION Mining companies are increasingly challenged by low grade, deep and complex ore deposits which are no longer economically exploitable by current methods. The large footprint of current open pit operations can present obstacles for permitting and social acceptance. For these reasons in-situ recovery (ISR) technologies are receiving renewed attention as a technology which could be used to exploit these more complex deposits economically and with less environmental impact. The environmental impact may be further reduced if emphasis is placed on use of renewable energy sources rather than traditional grid power, gas turbine or diesel generators are employed to drive the operation. A potential renewable energy driven ISR mine of the future is shown in Figure 1.

Jan 1, 2019

By H. R. Banks

"AbstractThe rod mill introduced into the Sullivan Concentrator flow in September, 1948, replaced two sets of 74 in. by 20 in. rolls and their accompanying screens. In addition to the work formerly done by the rolls, the rod mill is producing a finer product and one which provides more suitable feed for the primary ball mills. The object of the finer discharge from the •primary mills is to make possible a feed directly from the mills to a series of flotation machines where a large portion of the galena can be withdrawn from the circuit while the galena is still coarsely granular. The interposing of classifiers between grinding and flotation means the selective grinding of the galena.The author summarizes the work of •the rod mill through the first 5,000,000 tons and shows that the wear of lifters, liners, and rods is definitely below normal for the type and size of rock being handled. The rod mill, driven through a fluid coupling, has been subject to a range of speeds from 13.5 to 19. A pinion in the speed reducer was changed to allow the extending of the normal speed range of the fluid drive of approximately 4 r.p.m.Since the critical speed inside the liners •is 23.4, the range •in per cent of criticial is 57.7 to 81.2 per cent.The capacity of the mill increases with increasing speed but the character of the product remains approximately the same except when the feed rate is too high.Consumption of steel, power, and other operating data are presented.The author introduces certain fundamental observations on the principles involved •in comminution in order to support the special design and operation of the rod mill."

Jan 1, 1952

By A. K. Verma

This paper provides a brief overview of evolution of deformations, stresses, and pore pressures due to different excavation stages during construction of an URL. Excavation of a rockmass develops a damage zone of finite width around the excavated zone which is associated with changes in permeability and which affects the fluid flow mechanism. In this study, a coupled hydromechanical (HM) analysis has been conducted for a water saturated porous rock mass which has been created by sequential excavation and backfill of vertical disposal pit of an URL. For this purpose, an Atomic Energy of Canada Limited?s in-floor concept for a deep geologic repository suitable for Indian conditions has been used. Changes in rock deformations, stresses, strains and mechanically induced pore pressure in an undrained condition, during excavation, as well as those caused by mechanically induced rock deformations after backfill of the disposal pit, have been modeled. A three-dimensional finite difference tool FLAC3D has been used for the analysis.

Jun 1, 2012

By M. R. Saharan

A brief overview of rockburst control measures is presented. The paper then elaborates on one key rockburst control measure, which is known as destress blasting. A historical background of the technique is presented in order to understand different aspects of its field application. The publication enumerates key aspects of the technique as being used in practice in South Africa and North America. The paper also presents an analysis of three case studies in order to demonstrate difficulties associated with the field application of distress blasting in hard rock mines.

Jan 1, 2006

By D. Knuutila, G. Goyette, James A. Finch, G. Bartolacci, A. Fortin, Chi Ho Lau, A. Lockhart

"In a COREM-McGill collaborative research and development project, gas dispersion parameters and froth properties were manipulated in a copper flotation plant to study interactions between the collection and the cleaning zones. In this paper, specific work on developing some relationships between operating conditions and froth stability in a rougher column flotation cell of 125 m3 is reported. Froth stability, measured by image analysis, was related to the following process conditions for specific flotation machines in an industrial case study: Gas flow rate, collector dosage, pH, frother type and dosage. Across the range examined, froth stability was improved through a decrease in gas flow rate and/or increasing frother dosage. Metallurgical results (grade and recovery) showed that both gold and copper were dependent on froth stability.INTRODUCTIONMcGill and COREM have over the past two years collaborated in a research and development project to merge gas dispersion parameters, frother analysis (McGill technology), and froth properties (COREM’s imaging system) to study the interactions between the collection zone (pulp) and the cleaning zone (froth). The main goal is to increase knowledge of flotation cell hydrodynamics since it is known to govern the metallurgical performance of the flotation process (Power et al., 2000). In this paper, specific work on developing some relationships between operating conditions and froth stability in a copper flotation circuit is reported.The objective of this work is to study gas dispersion in a large volume flotation column (hydrodynamics) and to measure its impact on the froth. By froth imaging, it is possible to diagnose operational problems on the basis of froth characteristics (Bartolacci et al., 2005a) and consequently, to propose ways of improving process performance by froth analysis (Bartolacci et al., 2005b).Another approach to froth characterization is investigated in this paper. In the same flotation column, a froth stability apparatus (column) was included (Triffet and Cillers, 2004). The mechanical froth stability apparatus is used to link “hard” froth characteristic measurements to “soft” froth characteristic measurements (those obtained by imaging)."

Jan 1, 2008