Search Documents

By Mark W. Bartlett

Program Objectives ??Identify and implement a tool for haul truck drivers that: -Reduces or eliminates fatigue-related injuries and fatalities -Reduces accidents and equipment damage ??Following evaluation period, apply tool where most effective Why do We Need a Fatigue Monitoring Tool? ??Everyone has probably fallen asleep while driving ??Driver fatigue is a major source of property damage and serious haul truck serious incidents ??To protect ourselves from the other ?tired?driver ??To know when to ask for relief ??To know when we are seriously distracted from driving ??To measure improvements in sleep incidents based on shift changes and intervention ??To help prevent incidents like the following:

May 1, 2011

By Georges Houlachi, Akram Alfantazi, Maysam Mohammadi

Manganese ions in zinc electrowinning electrolytes form a protective MnO2 layer that ultimately decreases Pb contamination in the zinc product. In this study, the effect of dissolved Mn2+ on the electrochemical performance of Pb, Pb-Ca and composite Pb-MnO2 anodes was investigated. The properties of the MnO2 layer formed on these anodes were studied and compared. Potentiodynamic polarization and cyclic voltammetry experiments were performed in 180 g L-1 sulphuric acid to study the electrochemical reactions occurring on the anodes. The anodes were subjected to galvanostatic polarization at 50 mA cm-2. The morphology and uniformity of the MnO2 layer on the anodes were examined using scanning electron microscopy (SEM). Experimental results revealed that the MnO2 layer formed on the composite anode was more compact and uniform compared to that formed on the Pb and Pb-Ca anode. It was also observed that the cell mud formation rate, and consequently manganese ions consumption, depended on the anode type. Although initial formation of the MnO2 layer decreased the oxygen evolution overpotential, its growth might negatively affect electrocatalytic activity of the anodes.

Jan 1, 2014

By R. E. Bou Serhal

Many miners are exposed to dangerously high levels of noise on a daily basis. Over the past 15 years, a continually increasing number of occupational hearing loss has been reported from the mining community in the United States, of which, more than 95% is attributed to prolonged noise exposure. Although the noise exposure levels may differ between coal miners and metal and non-metal miners, in the absence of noise control at the source, the solution is the same: use of personal hearing protection devices (HPD). While protecting the miners? hearing it is also essential to no longer hinder their ability to communicate. With access to an advanced HPD that is customized to the miners? ears we are able to combine these two requirements. Using an intra-aural instantly custom molded HPD miners are protected from high levels of noise. The HPD is equipped with wireless capabilities, and contains both a speaker and an In-Ear Microphone (IEM). Therefore, the miners? speech may be captured from inside the ear and transmitted to the remote listener. This IEM signal is relatively noise-free since it is isolated from the background noise. The IEM speech signal, however, is ?boomy? and is missing some high frequency content, making fricative consonants hard to understand. Nonetheless, the IEM speech signal is correlated with the natural speech signal and may be manipulated through statistical techniques to more closely resemble natural speech. By improving the intelligibility and quality of the IEM signal, numerous applications may be enabled. One use of the enhanced IEM signal will be for radio communication. Using wireless radio communication in a noisy mining environment is sometimes the only practical and affordable solution to allow communication between miners equipped with personal hearing protection devices. Traditionally, one of the weaknesses of such wireless radio communication lies in the lack of designating receivers: whether they are the intended receiver or not, all those carrying a radio receiver are subjected to the broadcasted signal. The current work will detail a new concept of a "radio-acoustical virtual environment" where the radio signal will only be received by miners within a given spatial range, such range depending on the user?s vocal effort as well as the ambient and perceived background noise levels.

Aug 1, 2013

By H. C. Rickaby

Introduction The township of Swayze, from which the Swayze gold area derives its name, is in the Sudbury mining division, approximately 150 miles northwest of Sudbury. The gold area may be regarded as situated at the southwest corner of a triangular area whose northeast and southeast corners are at Porcupine and Shiningtree, respectively, and whose sides are between 70 miles and 90 miles in length. On a geological map, it would be found that belts of Keewatin greenstones and sediments form the sides of this triangle, and that they surround a large granite mass. Prior to the summer of 1931 the Swayze corner of this triangle had probably been less prospected than the other parts and comparatively little was known of it from the standpoint of gold mining possibilities. The extensive belts of iron formation to the south and west of Swayze received some attention about the year 1909, and during the years 1927 and 1928 some prospecting was done in the townships of Greenlaw and Cunningham, south of Swayze, but chiefly for base-metals- copper, zinc, and lead. In the summer of 1931 a very promising discovery of gold-bearing quartz was made by J. G. and J. L. Kenty, working for the Brett-Trethewey Mines, Ltd., in association with Northern Canada Mining Corporation, and Northland Prospectors, Ltd., and this property, now known as the Kenty Gold Mines, Ltd., has been actively developed with very encouraging results. Following this discovery a6d during the summer of 1932 much prospecting took place in the area, as a result of which a number of other discoveries of gold were made, chiefly to the west of the original find. They are distributed over a wide area, which includes the townships of Rollo, Raney, Swayze, Denyes, Halcrow, and Greenlaw.

Jan 1, 1933

By J. J. Brummer

"A reconnaissance geochemical survey, using the stream sediment technique, is described. The survey covered an area of about 400 square miles, in the Seal Lake area of central Labrador, underlain by basaltic flows, diabase and metadiabase sills, and sedimentary rocks. Previous work had indicated numerous small copper occurrences within the Seal Lake group of rocks. Stream sediments were tested for the readily extractable copper content and total heavy metal content. The results of the copper survey did not yield any new data on the distribution of copper mineralization. Results of the total heavy metal survey attracted attention to a remote portion of the area (Ten Mile Lake), which had hitherto been regarded as having no economic interest. The anomalous values found, suggested that zinc mineralization should occur in this region. Geological mapping indicated that the rocks exposed belonged to the Letitia Lake Group, which is older than the Seal Lake Group exposed to the east, which contains the copper mineralization of the district.Investigation of the area lead to the discovery of: (1) uneconomic lead-zinc mineralization; (2) radioactivity extending over a considerable area. Evaluation of the radioactive rocks led to the discovery of columbium-thorium mineralization in amphibolite and in diopside-actinolite schists along a contact with intrusive alkali syenite.Thus a geochemical survey, which was planned to evaluate a copper province, resulted in the discovery of lead-zinc-columbium-thorium mineralization."

Jan 1, 1960

By F. Flores

With the World Summit for Sustainable Development planned for 2002 in mind, nine of the world's largest mining companies decided to initiate a project to examine the role of the minerals sector in contributing to sustainable development, and how that contribution could be increased ? the Mining, Minerals and Sustainable Development Project (MMSD). This project assumed from the start that sustainable development could provide a useful framework to guide the minerals sector which main goal was integrating economic activity with environmental integrity, social concerns, and effective governance systems. The broad steps of MMSD project strategy can be grouped into four major categories: increase understanding of sustainable development; create organizational-level policies and management systems for implementing the principles of sustainable development; collaborate with others with common interests to take joint steps towards sustainable development, and; increase our ability to work towards sustainable development at the local, national, and global levels. In opinion of the article's author, to go ahead with the MMSD strategy and achieving the sustainable development objectives, it is necessary to consider the concept of self-organization, fundamental of the emergent new scientific paradigm, and the consequent epistemology and values that conform a supporting culture for sustainable development.

Jan 1, 2007

By S. Aram

Concrete reinforcing requires coordination among many roles: structural engineer, estimator, detailer, fabricator, installer and others. The methods used to define and represent concrete reinforcement elements and assemblies in building information models is crucial in determining the efficiency of sharing data among BIM platforms and the effectiveness of using the carried data in production planning, fabrication and site work activities. Starting from the information items that are required to be provided by BIM platforms, as defined in earlier work, we have developed the Industry Foundation Classes (IFC) bound Concepts and Model View Definitions (MVDs) for concrete reinforcement. Furthermore, in coordination with software developers, we propose guidelines for best practices for concrete reinforcement modeling. Implementing these guidelines by software providers will improve reinforcement modeling with regard to various aspects of reinforcement products like geometric representation, placement, and property specifications. The proposed approach is selected as a way to improve functionality of the shared data for production planning, fabrication, project management, and site activities. Guidelines for assigning information to rebar type and instance definitions as well as to rebar elements and assemblies are provided. An efficient method of sharing geometry and property sets among rebar instances of a rebar array is also defined.

Aug 1, 2013

By C. Villaseca, F. Penna, R. Villarroel

Acid mist is the undesired result of copper electro-winning (EW) process, generating a contaminated and hazardous environment in the working areas, as well as promoting high corrosion conditions for structures and equipment in the EW tank-house due to the buoyancy of sulfuric acid in aerosol form. Likewise, organic entrainments that occasionally occur in this process contaminate the cathodes, as well as increasing the risk of fire. LateralVex® and LateralFlow® are technologies that effectively and efficiently solve these problems, without affecting the usual activities of the operators, thus presenting a significant distinction with respect to other technologies that seek to solve these problems. Minera Antucoya, an AMSA group company, which produces 80,000 tons of electrolytic Cu per year, decided to install both technologies for its EW tank-house, LateralVex® in commercial cells and LateralFlow® in scavenger cells to keep both the acid mist and the organic entrainments under control. This paper presents the effects of applying these technologies in Minera Antucoya’s electro-winning plant, the challenges addressed, the difficulties encountered, the problems and opportunities that their implementation involved, as well as the surprising results obtained at the time of measuring the acid mist— less than one hundred’s part of the Allowed Weighted Limit—in samples taken with the plant operating at maximum current capacity. Additionally, the paper includes some of the improvements identified during the period, more than 3 years, in which these technologies have been in operation in Minera Antucoya. INTRODUCTION Electrowinning is the most used electro-chemical process in the hydrometallurgical industry for the recovery of highly pure metallic copper as its final product, which is formed in previous stages in an aqueous medium that goes through a selective process using organic solvents to separate impurities and concentrate the metal in a sulfuric acid solution. In the last stage, this solution goes through a process in which high- density current at a low voltage is applied, so that the metal in the solution will deposit in solid state on a plate, usually a stainless-steel plate. This last process involves the generation of other sub-products due to the electro-chemical dissociation of the electrolyte’s components, or to the addition of chemical additives, or due to specific physical conditions or lack of controls during the operation.

Jan 1, 2019

The mining industry has generally been slow to apply ion exchange processes to hydrometallurgical applications even if ion exchange offers an ideal solution for a particular problem. Two notable exceptions are in gold and uranium recovery. The largest application of ion exchange in the metals processing industry has been the use of resin-in-pulp (RIP) for gold recovery as an alternative to activated carbon. Iron is a ubiquitous impurity in hydrometallurgical solutions. In many cases, bulk removal of iron from the process solutions is accomplished by precipitation. However, precipitation for iron control is often accompanied by losses of base metals by co-precipitation. Increasingly, the option of ion exchange for removal of smaller amounts of iron from process solutions has been favoured. A number of applications have been developed and proven at the commercial scale for the removal/control of iron from a range of metal processing solutions. This paper provides an overview of the application of ion exchange for iron removal from a range of metal processing operations, including Cu, Ni and Co solutions. A number of case studies are provided which review operational and resin regeneration strategies and the impact upon the commercial operation of metal processing with improved iron control.

Jan 1, 2006

By W. R. Tyson

Imperfections such as lack-of-fusion and undercut are inevitable in field welding of pipelines. Above a certain size, such defects must be removed or repaired. In the present state of the art, determination of allowable defect size is done by Engineering Critical Assessment (ECA). This requires measurement of toughness, and comparison of toughness with crack driving force. ECA methods used in current international pipeline standards will be reviewed and compared.

Jan 1, 2010

By D. Chakravarty, B. Samanta, D. Ghosh

Autonomous robots are useful for 3D underground mine mapping to avoid human exposure to hazardous spaces. To prepare a precise mine map, a self-navigating robot must navigate an arduous path, avoiding obstacles and sensing the environment. A prototype laboratory-scale robot was built and evaluated through a mock-up in a test mine gallery. It was outfitted with a 2D laser scanner, a stereo camera for obstacle avoidance, and a high-precision, laser-based imaging and digitizing system for collecting 3D point cloud data. Various algorithms were used for scan matching to facilitate simultaneous localization of the robot for mapping.

Jan 1, 2014

By T. S. Grewal, S. C. Gupta, H. Natarajan, T. W. McQuade, N. Nejibulloev-Mamedov

Cigar Lake is one of the world’s largest high-grade uranium mines. The ore mined at Cigar Lake is milled at Orano Canada Inc’s (Orano) McClean Lake mill. The average Cigar Lake ore uranium grade since the start of mining activities in 2014 is 17.8% U (range 8– 28%). To achieve budgeted production of 18 M lbs U3O8/yr the required average feed tonnage to the mill is about 45 kt/yr. Arsenic, occurring as arsenides and sulpharsenides, is one of the major elements of concern associated with Cigar Lake ore. The leaching process is a sulphuric acid leach under oxidizing conditions at near atmospheric pressure. The presence of arsenic in the ore consumes oxidant in leaching as well as ferric sulphate in tailings preparation for arsenic sequestration. The average arsenic grade since the start of mining at Cigar Lake is 0.57% As. Further, the ore is hosted in a matrix of sandstone and clay, which results in poor settling in CCD. The average uranium grade for the balance of Cigar Lake Phase 1 ore is expected to drop to 12.5% U and the average arsenic grade is expected to increase to 1.6 % As, with an annual average peak of 2.5%. Therefore the tonnage throughput required to sustainably meet the production target will increase to 55 kt per year. Orano partnered with Hatch Ltd. (Hatch) to perform a gap analysis study to identify key circuits and equipment in the mill that would require debottlenecking. A METSIM mass balance model of the McClean Lake mill was generated and validated with actual mill operating data. Various feed scenarios were then studied, and the outcome was a traffic light table, which highlighted feed scenarios that exceeded installed capacity of major equipment and circuits. The results provided the basis for the PDC for the pre-feasibility study. This paper will outline the results of the gap analysis, the mass balance model, the feed scenarios and the study undertaken to prepare the McClean Lake mill for the change in ore quality from Cigar Lake.

Jan 1, 2020

By M. U. Oko

"Monitoring of all the waste streams from Falconbridge's Sudbury Operations to determine whether they meet the required standards, has been performed for many years. By 1969, however, the number of samples being collected had become so large that a complete revision of the existing systemwas necessary. Sites previously designated by name only, were numbered, clearly marked on the ground and on maps which were circulated to all concerned. The types of pollutants analyzed were determined and specified for each sampling location and a chemical analysis report form was designed. The sampling schedule has been computerized to produce a periodic listing of the samples to be taken and the analyses required.An area map showing sampling sites, chemical analysis report form, spill report and a computer print-out example are shown and explained.EVOLUTION OF FALCONBRIDGE'S WASTEWATER. MANAGMENT SYSTEMFalconbridge Nickel Mines employs some 4500 people, operates nine mines, four mills and a smelter in the Sudbury basin. The operations are geographically fragmented into four widely separated locations, the Falconbridge operations east of Sudbury and the Onaping operations in Levack Township being the two largest of the four. The Lockerby area located to the west and the Lindsley Mine just north of Sudbury are now under development. The magnitude, the diversity and nature of the operations are such that constant vigilance is needed to prevent inadvertent damage to the environment. The purpose of this paper is to describe the information system used to monitor and control waste-water disposal on Falconbridge's properties to help ensure the maintenance of effluent standards satisfactory to the Ontario Water Resources Commission (OWRC) and to the Ontario Department of Health."

Jan 1, 1971

By J. P. Jylhä, A. Jokilaakso

The Outotec Flash Smelting process is widely used in primary copper production. A layer of slag on top of matte (copper–iron sulphide melt) creates a barrier through which matte droplets descend. Droplets of different sizes settle through the layer at different rates, which increases possibility of copper losses as smaller matte droplets may be removed with the slag. In this work CFD-DEM (computational fluid dynamics – discrete element method) coupling was used to simulate matte droplets settling through the slag during slag tapping. Discrete droplets and slag flow were simulated with DEM and CFD, respectively. This new approach enables tracking and solving movement and interactions of individual droplets. User-defined models were created to take coalescence and reaction kinetics into account. Coalescence created larger droplets, while the reactions decreased droplet size and increased its density. Drag caused funnelling effect, which pulled droplets towards the centre line of the descending cluster. This research is the only study known by the present authors in modelling liquid-liquid systems with the CFD-DEM coupling. Simulating coalescence and chemical reactions for discrete droplets enables more realistic simulations. However, CFD- DEM simulations are computationally resource intensive already without additional models, so a full scale industrial settler modelling still waits for further increase in computer performance. INTRODUCTION Flash smelting is a method used in copper and nickel production. In the flash smelting process, oxidation of sulphides in a concentrate is used to release energy needed to smelt the feed. In the process, copper matte is formed. Matte has copper content in the range of 55 – 70% (Sridhar, Toguri, & Simeonov, 1997), the rest is mainly sulphur and iron but has still many other impurities (Taskinen, Seppälä, Laulumaa, & Poijärvi, 2001). Oxidized iron forms iron-silicate slag while SO2 is collected for acid production (Davenport & Partelpoeg, 2015). The Outotec flash smelting furnace (FSF) can be divided in four major component: concentrate burner, reaction shaft, settler and uptake. Concentrate, flux and oxygen enriched air are injected into the reactor through the concentrate burner. The mixture then reacts in the reaction shaft forming matte and slag, which are collected in the settler, while off-gases flow out of the reactor through uptake for heat and dust recovery, and SO2 collection for H2SO4 production. The matte and slag form separate layers due to immiscibility and density difference. Raw material feed is continuous, but the matte and the slag are tapped periodically. A flash smelting furnace is depicted in Figure 1.

Jan 1, 2019

By A. I. Gorshkov, Y. A. Bogdanov, O. Y. Bogdanova

Abstract - Detailed crystal-chemical study of iron and manganese oxides and some other minerals from low-temperature hydrothermal deposits in a newly discovered inactive mound in the TAG hydrothermal field were used to determine the precipitation sequence of mineral phases during lowtemperature processes and their post-sedimentary transformations. Particles of primary sedimentary X-ray amorphous proto-ferrihydrite with high silica content were replaced in situ by nontronite, ferrihydrite, or goethite during alteration. Ferrihydrite is the only proto-hematite phase. The transformation of the iron minerals, related to change in the physicochemical environment, is an important characteristic of low-temperature hydrothermal processes. The occurrence of hydrogenetic Fe vernadite and Mn feroxyhyte in the uppermost part of low-temperature deposits and bottom sediments near the base of the mound is evidence for cessation of low-temperature hydrothermal processes. Among the investigated mineral phases, goethite, nontronite, and hematite are stable in reduced sediments only.

Jan 1, 1999

By S. Litke

Elemental sulfur was stockpiled at the Mount Polley Mine for use as a source of sulfuric acid as part of research into leaching copper from oxide ores, but the project did not proceed beyond an initial pilot- scale evaluation. Since placement, the sulfur has oxidized and some sulfuric acid leached into the underlying rock. The reaction of the acid with these underlying materials has been studied as part of an evaluation of the effects of leachate from the pile. The rock underneath the sulfur pile is composed dominantly of primary and secondary alumino-silicates with less than 1% carbonate (calcite) and iron sulfide (pyrite). In its unaltered condition, the rock is classified as non-acid generating. Conceptually, it was expected the sulfuric acid would be neutralized by the rock to varying degrees resulting in a series of pH-controlled weathering fronts progressing from leached near the contact with the sulfur pile (pH <3), to active neutralization by silicates (pH 4–5), to active neutralization by carbonates (pH >7). The rocks underneath the pile were sampled to determine the extent to which the rocks had reacted and their long-term stability after removal of the acid source. INTRODUCTION When rock is blasted and excavated to facilitate mining ore, it is typically placed and stored on the surface in piles. The resulting drainage may have a neutral to basic pH (i.e., non-acidic drainage) or a low pH (i.e., acid rock drainage, ARD) depending on the mineralogy of the rock being stored in the piles. Acid- base accounting (ABA) can be used to characterise the two types of rock: potentially acidic drainage generating (PAG) and not potentially acidic drainage generating (NAG) (Price, 2009). According to Price (2009), NAG is defined as having an excess of neutralization potential (NP) in the rock in the form of calcium carbonate-like minerals when compared to acid potential (AP), i.e., a Neutralization Potential Ratio (NP/AP = NPR) greater than 2.0, whereas PAG is classified as having an excess of AP (i.e., an NPR less than 1.0). This is a conservative estimate and may be slightly modified depending on the mineralogy at specific mine sites. Rock with an NPR of 1–2 is also capable of generating acid (Price, 2009) and, depending on the mineralogy, may also be classified as PAG. Drainage from PAG material can generate acid immediately, or many years after it has been exposed to surface conditions. Disposal techniques depend on the category (i.e., NAG or PAG) and reactivity of the rock stored in the piles.

Jan 1, 2019

By L. Furtenbach, T. Möller

"Grinding mills are the heart of the mineral processing plant, and are production-critical machines which are required to achieve high availability. Liner wear life and a liner design that promotes ease of installation are important variables to achieve a high level of mill availability. Increased mill size results in more mill internal surface to protect, and more liner components to install and remove. This drives designers toward an increase in liner size to minimize the number of components to be installed by the liner handler. The liner attachment method can also have a large impact on mill availability as well as safety during installation.This paper outlines the experience from the development, installation and follow-up of liners installed in two 38&apos; x 45&apos; AG Mills at Boliden Aitik in Sweden. A new Poly-Met shell liner concept has been developed to minimize the number of liner components. The new Poly-Met shell liner components are made much larger than conventional Poly-Met or steel liners. This reduces the number of components to be installed/removed by the liner handler and helps to minimize installation time and consequently down- time. A new attachment system has also been developed to eliminate the need for the installation crew to be in the “drop-zone” of the shell liners while installing the liner bolts.One interesting aspect of this project was the requirement to predict liner life for these new large format AG mills. The existing 22&apos; diameter mills at Aitik provided a base-line reference for this purpose, and DEM studies were used in the project development stage to predict the wear life of shell liners for the new 38&apos; diameter AG mills. The results from this study are included."

Jan 1, 2012

By A. Roca, V. A. Quezada, O. A. Benavente, M. Cruells

The leaching pretreatment of copper ores is widely used in the Chilean mining industry. Agglomeration and acid curing have been identified as the most useful pretreatments. Of these, acid curing was recognized as beneficial in the dissolution of copper minerals, even in sulphides such as chalcopyrite. Extensive acid curing times have an impact on copper extraction, generate a homogeneous acid distribution in the mineral bed and benefit the inhibition of aluminum-silicate minerals (acid consumers). This document describes some of the theoretical background and results regarding the effect of acid curing in a chalcopyrite sample with 74% purity according to Qemscan analysis and a 28.5% of total copper. Leaching tests are carried out at 25, 50 and 70°C, evaluating the effect of a pretreatment on the chalcopyrite dissolution. The original sample and products generated were characterized by X-ray diffraction analysis and Scanning Electron Microscopy (SEM). The performed experiments indicate a direct relation between the effect of curing time and temperature in copper extraction. 92% of copper can be extracted in a leaching at 70°C and with 15 days of curing. Elemental sulfur, jarosite and copper polysulfide (CuS2) have been detected in leaching products. INTRODUCTION The copper extraction from minerals is a technique that has been developed for hundreds of years in the world. In 2017, the largest copper producer was Chile, exported 5.5 million tons (COCHILCO, 2018). However, in order to preserve this production level means overcoming multiple challenges. In the case of the Chilean copper deposits, the average copper grade in 2016 was 0.65%, lower than the 1% declared in 2004 (Consejo Minero, 2018). This is mainly due to the deeper of the deposits reaching sulfide mineral zones, mainly chalcopyrite. Traditionally, these sulfurized zones ore are treated through concentration by flotation and subsequent pyrometallurgical treatments. However, for some copper companies it is complex to process by this alternative, due to the high costs and high rates of water consumption. The mineral resources of these companies are known as "low-grade sulfides" and do not allow, economically, the treatment of these minerals through concentration by flotation. This is how hydrometallurgy becomes an alternative for the treatment of this type of deposits. In addition, several companies have hydrometallurgical plants, which would allow the operational continuity of these plants.

Jan 1, 2019

By T. Lux, H. -J. Krassnig, I. Filzwieser, E. Hecker, R. Degel, A. Filzwieser

Non-ferrous metals find their applications in smartphones, tablets and computers. These materials with their particular properties are the basis of our modern life. SMS group is well prepared for this huge market and for growing future challenges. A large contribution here is the new joint venture PolyMet Solutions that was founded by SMS group and Mettop, an Austrian engineering company, with the objective to develop new technical solutions for the primary copper production lines as well as for non-ferrous metals starting with the primary smelting of concentrate and ending with the electrolysis. PolyMet Solutions provides the process know-how whereas SMS group supplies the plants and equipment and Mettop the key components. SMS group and Mettop also cooperate in the field of tankhouse technology. Together with Montanwerke Brixlegg AG, Mettop has developed together with a parallel flow technology (METTOP-BRX Technology), allowing a current efficiency of above 98 % at a current density of 420 A/m², which is a milestone in copper electrolysis. For the secondary copper production route, SMS group and PolyMet Solutions developed an innovative refining furnace (PolyRefine) for the smelting and refining of copper scrap. The refined copper is directly charged to the Contirod line to produce copper rods and wires. The innovative cooling solutions of SMS and PolyMet Solutions come into play where furnaces have to stand the highest loads and stresses, for instance in areas of very high temperatures or temperature fluctuations, aggressive exhaust gases and slags, or at critical spots such as taphole areas. Custom-tailored cooling systems for furnace vessels make sure varying loads are compensated in a targeted and effective manner. The solutions include air cooling, spray cooling, cooling technologies with integrated copper elements such as CFM (Composite Furnace Modular) cooling systems, plate and finger coolers. The major innovation in the field of furnace cooling is the ILTEC (Ionic Liquid Cooling) Technology which paves the way for increased plant safety. This revolutionary, patented cooling technology is jointly marketed by Mettop and SMS group. It permits water-free cooling to be implemented and thus makes operation safe wherever it is applied. INTRODUCTION Non-ferrous metals or NF metals are changing the world. There is no modern industrial sector that can do without these valuable metals. Non-ferrous metals find their applications in smartphones, tablets and computers. These materials with their particular properties are the basis of our modern life. The importance of the non-ferrous metals market is reflected by two figures. In 2018, the production of non-ferrous metals was worth more than 237 billion Euros. This contrasts with 255 billion Euros of the value of iron and ferro- alloy production in the same year (International Organizing Comittee for the World Mining Congresses, 2018). Hence, the NF metal industry is almost as important as the iron and steel industry. SMS group is well prepared for this huge market and for growing future challenges. A large contribution here is the new joint venture PolyMet Solutions that was founded by SMS group and Mettop, an Austrian engineering company, with the objective to develop new technical solutions and to enhance customer value. The prices of nearly all metals have come under pressure during the past few years. Therefore, competitive technologies are regarded a crucial factor to achieve success in this critical market situation respectively to stabilize the market position.

Jan 1, 2019

The 2-4D window shown above is the base startup window which allows you to begin a new project. ??Setting up the project is the first step ??The next step is to setup the properties to be used in this project

Feb 1, 2008