Search Documents

By Denby B, Hollands R. Schofield D

Surface mines are in operation worldwide, the vast majority employ large haul trucks for the transfer of material both to the outside world and around the site. The sheer size of these trucks and the operating conditions means there is a high

Jan 1, 1998

By Szwedzicki T

Uniaxial testing was performed on model pillars to determine the effect of width to height ratio on pillar and surrounding rock mass stability. Samples were modelled in a shape similar to that of dumbbell weights, with the centre representing

Jan 1, 1994

By Rogers M, Sullivan B

Golden Crown Mine is a narrow vein gold mine producing 75000 tpa. Production has been predominantly by shrink stoping using hand held machine and airleg. Bogging from these stopes is done with Toro 150 LHD units.Previously the standard development method consisted of developing a sill drive, a footwall drive and millholes every 7 m. This meant that for every metre of ore development, 2 m of waste development was required.

Jan 1, 1993

By Armstrong AB

It has been identified that particulate matter in the form of suspended solids and bed load has the ability to adsorb heavy metals. Each year Ranger Uranium Mines Pty Ltd (RUM) identifies potential danger areas which could become major sediment sources during the wet season. Methods of suppressing sediment uptake such as hydromulching and coating areas with Poly Vinyl Acetate (PVA) glue are used. Other methods of reducing the sediment load after uptake such as diversion bunds, filters across drains, stone filters, minor sumps and settling ponds are also used. The 1983/84 wet season saw drain sediment loads reduced to acceptable levels before the water reached the outside environment. Studies to qualify and quantify flows from minor drains are still underway.

Jan 1, 1984

By Jones A

Today there is a vast amount of information available relative to the performance of tunnel boring machines, and associated systems. The data referred to here consists of project reports, manufacturer's equipment literature and papers concerning almost every aspect of the excavation process. Why is it then, that many projects that employ full face tunnel boring machines (TBMs), on average perform significantly less than the peak performances reported in this industry?

Jan 1, 1993

Conveyor belt haulage offers the advan tages of continuity of operation, minimum labour requirements, and the ability to handle large volumes of material over extended periods. However, breakdown of critical con- veyors in the system can cause undue and substantial losses in production output at the working faces, unless adequate surge bin capacity is incorporated in the haulage system. A conveyor belt simulation programme, code name 'Beltsim' was developed by Bucklen et al (1968) at the Virginia Polytechnic Institute in the U.S.A. and provides a quantitative measure of the performance of a conveyor belt network design. A limitation still exists with the computer programme and involves the inability of the programme to predict the necessary surge bin capacity to overcome conveyor belt downtime. The computer programme was modified to overcome this limitation, to simulate a con- veyor belt breakdown, and to provide a quantitative prediction of the surge bin capacity necessary to permit a modern mining system to operate effectively and continuously.

Jan 1, 1977

THE filter-press, which has done so much for the successful-treatment of the sulpho-telluride ores of Kalgoorlie, has a serious rival in the vacuum process, and this paper is written with a view to arousing more interest in the cheaper working of the press, it being doubtful whether its efficiency in extraction can be improved upon. Before proceeding with the actual working of the press, it may be as well to make brief mention of the character of the ore treated at the Associated Northern Blocks, where these notes were compiled. A sample from several weeks' run was taken of the raw ore, with the following analysis...

Jan 1, 1911

Trial ore production began at the Hilton Mine in 1987 with ore being trucked into Mount Isa for treatment at the Lead/zinc Concentrator. The expansion of output from the Hilton mine required additional concentrator capacity which led to the design and construction of the Hilton Concentrator. Systematic laboratory and Pilot Plant testwork dating back to 1968 to develop a flowsheet and reagent regime suited to the varied and generally complex mineralogy of the Hilton ore was successfully concluded with a Pilot Plant trial using a sulphoxy based sphalerite depression system in early 1988.In May 1988, a decision was made to build a 750 000 t/y concentrator with some novel technological and capital-efficient features. The Hilton Concentrator commenced operations in December 1989 reaching target grinding rates and metallurgical performance by mid-1990. Current ore treatment rate is 800 000 t/y.Lead concentrates assaying 43 - 48 per cent Pb are combined with the Lead/Zinc Concentrator lead concentrates and smelted at Mount Isa. Zinc and Low Grade Middlings (LGM) concentrates are filtered in the zinc filter plant at Isa with those from the Lead/Zinc Concentrator and then railed to Townsville for export or treatment in Australia.

Jan 1, 1993

This paper deals briefly with productivity-enhancing advances in shaft sinking technology in South Africa post-World War II in general and the developments and application of long rounds since the 1980s in particular and is amply illustrated.It touches on the conversion to circular section, concrete lined shafts, the introduction of tungsten carbide drill bit inserts and grab lashing; expounds the rationale driving the development of longer rounds; and then describes the evolution of long rounds using hand-held and mechanically mounted rockdrills in South Africa and Canada by both local and foreign contractors. The recent experience gained on the sinking of the South Deep Main Shaft follows. Results obtained from this experiment are tabulated and commented upon. The paper concludes with the postulation of æwhat nextÆ and æwhere toÆ scenarios. Addenda include a list of shaft rounds in excess of three metres in length blasted in the Main Shaft at South Deep and their results, typical round design, manufacturerÆs specifications for the 6 m shaft jumbo and rock drills.

Jan 1, 2002

By Stanton G

The Department of Mapping and Surveying (DMS), the Australian Key Centre in Land Information Studies (AKCLIS), the Department of Industry Development (DID) and the State Government Computer Centre (SGCC) are testing a regional information network in northern Queensland. Several study sites have been chosen by different groups of participants. The members of each common-interest group share their data for the site. They can also access datasets supplied by other organisations that are not directly involved in the particular study being undertaken. The participants include state government departments, local authorities, fed- eral organisations and the private sector. The participants communicate with computer systems in Brisbane via Q-Net. Q-Net is a pilot State government tele- communications network, established by the Department of Industry Development. Q-Net uses the communications sat- ellite AUSSAT 1 as the primary instrument of data transfer. The Q-Net network is a star system, with a Master Earth Station in Brisbane acting as a hub for radial earth stations, located throughout Queensland.

Jan 1, 1987

High sulphur volcanic-hosted hydrothermal environments are favourable geological environments for gold mineralisation. Numerous world-class gold deposits including Pueblo Viejo (Dominican Republic), Goldfield (Nevada), EI Indio (Chile), and Wa

Jan 1, 1994

By Potter DJ, Firkin GR

The Imperial Smelting Furnace operated by Sulphide Corporation Pty. Limited at its Cockle Creek zinc-lead smelter was recently equipped with tuyeres angled at 25 degrees instead of the usual 10 degrees. This change was prompted by the results of model studies undertaken by tha Research Department of Imperial Smelting Processes Limited, at Avonmouth in the United Kingdom, and by the favourable results of operating trials on the Cockle Creek furnace using bent-tip tuyeres to simulate 25 degree inclination. The use of 25 degree angle tuyeres has made it possible to operate with lower zinc values in discard slag and has improved hearth stability over a wider range of sinter quality and composition.

Jan 1, 1981

By Nixon TR

The Australian Coal Industry Research Laboratories Ltd. (A.C.I.R.L.) MINVENT computer program can be used to simulate existing and projected colliery ventilation requirements. New collieries can be planned using a database of ventilation parameters which were ascertain- ed by A.C.I.R.L. surveys at selected collieries in N.S.W. and Queensland. Several techniques are used in both the formulation of the database and in the evaluat- ion of a ventilation system, prior to analysis by the MINVENT program. The analysis of a ventilation system requires the measurement of air quantities, pressures and hence airway resistances. All resistances are calculated at standard air density of 1.205 kg/m3. Air densities are derived from barometric pressure and wet and dry bulb temperature readings. Airway frictional and shock losses, leakage through stoppings and overcasts, flow of air through regulators, face resistance and resistance of anomalous ventilation features are related to the typical Australian measured data presented.

Jan 1, 1983

By Selby DW, Hamill J, Cauley ID, Thomas I, Thornton AJ

The main objective of sulphide flotation in a cassiterite concentrator is to remove sulphide minerals (pyrite, pyrrhotite and sometimes chalcopyrite) from the ore prior to gravity concentration. Tin losses in the sulphide flotation stage account for a significant proportion of the total tin loss. separate studies of the sulphide flotation circuits of Renison Ltd and Cleveland Tin Ltd were conducted to investigate reasons for the tin losses. Sampling surveys were conducted in the rougher-scavenger and also the regrind-cleaner sections of both plants. In both plants, the rougher circuits recover excessive quantities of liberated cassiterite, while recovery of the desired composite cassiterite-sulphide fraction is low. The regrind mills are successful in liberating the composite cassiterite in the rougher concentrate, but at the expense of increasing the proportion of very fine tin mineral. The cleaner circuits recover between 40 and 60% of the cassiterite received, and this is all lost.

Jan 1, 1978

By N Javati, G D. Carman, D Kikiha, B Likia, K Dala, J McPhie, R Johnstone, D R. Cooke, J L. Blackwell

The 40 Moz Ladolam gold deposit on Lihir Island, Papua New Guinea is the worldÆs largest, low-sulfidation, epithermal gold deposit, in terms of contained gold. The deposit has average grades of 2.42 g/t Au (LGL Resources Reserves Update, 2008) and gold is hosted primarily in refractory pyrite. Lihir Island is part of the 150 km long, Tabar-Lihir-Tanga-Feni, alkalic, volcanic island chain located in the New Ireland basin. Five volcanic blocks comprise Lihir; Plio-Pliestocene Huniho, Kinami and Luise volcanic edifices are built on top of remnant Pleistocene Wurtol Wedge and Londolovit Block (Wallace et al, 1983). The Ladolam gold deposit is located in the central portion of the dissected Luise volcanic edifice and is composed of four main orebodies: 1. Minifie, 2. Lienetz, 3. Coastal, and 4. Kapit. An active geothermal system is overprinted on the ore deposit, localised along north-trending lineaments, and is expressed as hot mud pools and fumaroles. The focus of open pit mapping and drill core logging, as part of ongoing PhD research, has been in the Minifie and Lienetz orebodies. The deposit geology is grouped into four main phases: 1. volcano-sedimentary host rocks, 2. porphyry-style biotite alteration and related hydrothermal breccias and veins, 3. epithermal-style breccias and veins, and 4. modern geothermal alteration. Gold is associated with epithermal-style alteration and mineralisation. Ongoing observations of the Minifie and Lienetz orebodies are highlighting differences in the geology and paragenetic histories. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By Edwards A. B

Re-opening of the old Proprietary mine has provided new exposures of the system of uralite dolerite dykes observed in 19110 by the Geological Sub-Committee of the Scientific Society of Broken Hill. The newly exposed dykes have been invaded and replaced by the massive ore, with development of manganese garnet and biotite adjacent to the sulphides. A similarly altered dyke in massive ore has been encountered in the North Broken Hill mine.The textures of the unaltered portions of these dykes indicate that they have not been affected by the intense regional metamorphism that has recrystallized the other rocks of the area. Moreover, in mineral composition and textures, in chemical composition, and in cross-cutting relations, they are so similar to the uralite dolerites of the district which post-date the folding and metamorphism of the Broken Hill area, that they must be regarded as typical members of this suite of post-metamorphic dykes.The invasion and replacement of the dykes by the massive sulphide ore, and their metasomatic alteration adjacent to the invading sulphides, establishes that the lode was formed after the dykes were intruded, so that the high temperature features of the ore cannot be attributed to metamorphism and recrystallization, but are primary features of high temperature hydrothermal deposition.INTRODUCTIONTwo cross dykes are recorded on the plan of the 300-ft. level of the Broken Hill lode accompanying the report on the geology of the Broken Hill lode published by the Geological Sub-Committee of the former Scientific Society of Broken Hill (1910). One dyke occurs in Block 12, and the other in Block 13, and both were stated to consist of a dark basic amphibole rock, called diorite for convenience. The more southerly dyke was traced from some distance out in the footwall, and even through the lode, by means of occasionalpatches of it still existing in the ore, in a direction...

Jan 1, 1956

By Grant J

In surface mining, significant improvements in efficiency can be obtained through greater control over the formation of the muckpile. By tailoring the muckpile shape and its looseness to the requirements of the excavating equipment savings can be rea- lised through increased production, machine life and reduced maintenance. For instance, one open cut coal mine has recently estimated that a 2001o improvement in its front row throw would realise $320,000/year savings in rehandle costs alone. Previously greater throw has been achieved by increasing the powder factor through increased quantity of explosive or by drill- ing a larger number of holes-both at a significant cost penalty. However a recent series of experimental blasts demonstrated that it was possible to achieve a twofold increase in the distance of throw of a single row blast by simply changing delay timing alone. The Nobel Electronic Delay Detonator was used to provide the timing flexibility and control required for a thorough study of the effect of blast timing on heave. Whilst it is well accepted that the front row of a blast dominates the extent of throw, it was also found that the profile of the blast could be significantly altered. To date, the general consensus has been that the muckpile for- mation from a blast is a function of the blast geometry, the rock type, the explosive and the initiation sequence. Typically the geometry, rock type and initiation system have a far greater impact than the explosive type. This has been demonstrated by many high speed film studies. However the extent of influence via initiation has rarely been fully evaluated, owing largely to the limited control offered by conventional detonators.

Jan 1, 1988

Magnetic separation using particle rotation in a continuously rotating magnetic field offers very low to insignificant non-magnetic particle entrapment, and precise magnetic fractions. The precision of rotating magnetic field separations makes the method ideal for dry laboratory magnetic analysis work, where conventional laboratory magnetic separators can give misleading or uncertain data. The very low entrapment characteristics make the method ideal for entrapment-critical separations within the diamond exploration industry or in gold recovery. A single wet rotating magnetic field (RMF) unit is able to achieve a cleaner separation (at similar or better recovery rates) than a three-stage separation using conventional wet drum separators. The RMF separator is able to work effectively at particle sizes below 50 ¦m, and RMF separation could, at least in theory, be used down to single domain particle sizes. Rotating magnetic field (RMF) separation is carried out by magnetically spinning the particles at frequencies up to 300 Hz. The particle rotation itself may be used to roll the particles out of the separator. At angular velocities of 100 Hz, magnetic flocs are unable to form, and any entrapped particles are energetically expelled. In an RMF separator, the outer drum can be stationary while the inner magnet rotor rotates, allowing, for example, the injection of cleaning water underneath the separating magnetics to help remove small suspended non-magnetic particles.

Jan 1, 2000

A conventional Bucket Wheel Excavator (BWE) system with conveyor transport, mobile tripper and spreader was commissioned at the Goonyella Mine in 1982. The system was introduced to prestrip ahead of dragline excavations and was specified to remove 7.5 million cubic metres per annum in ground somewhat harder than that inwhich bucket wheel excavators are normally operated.This machine has, since 1982, moved more than 77 millionbank cubic metres of material and has been relocated twice. Extensive trials have been undertaken including digging blasted rock.

Jan 1, 1992

In the process of mining the lower seam in a multi-seam operation, a lot of oblique fract- ures appeared in the upper seam which was in the equilibrium zone. These fractures closed soon after the lower face line passed. Despite the occurrance of some degree of undulations, and and step-like unevenness, the upper seam was subsequently extracted without difficulty. When attempting multi-seam extraction, from the height of the equilibrium zone, the minimum distance between seams in ascending mining should be predicted. By analysing roof con- vergences data and the geometrical configuration of subsidence profile, it was found that the minimum safe distance for ascending multi-seam mining depends on the mining height of the lower seam and the properties and structure of the inter-stratified rocks.

Jan 1, 1986