Search Documents

By M A. Rhamdhani, K Avarmaa, A Putera, J Chen, G Brooks

Silicon-based photovoltaic cells are currently the most dominant types applied to convert solar energy to electricity. In solar-grade silicon (SG-Si), the control of boron (B) and phosphorus (P) is very critical. Generally, these elements are difficult to remove into acceptable sub-ppm levels from lower grade Si. This study investigates slag treatment as a process for Si refining, focusing on the behaviour of P and B. The experiments were conducted by equilibrating Si-B-P alloys with 43 wt per cent SiO2 – 47 wt per cent CaO – 10 wt per cent Al2O3 slag under inert atmosphere at 1500°C. Different crucible materials were used (Al2O3, SiO2 and MgO), which determined the primary saturation phase for the system and modified the final slag composition accordingly. The samples were equilibrated and analysed with microanalysis techniques (EPMA (electron probe microanalysis) and LA-ICP-MS (laser ablation inductively coupled plasma mass spectrometry)). New standards were prepared and applied in the LA-ICP-MS analyses. Experimental results show that silver is essentially fully dissolved in silicon, as well as most phosphorus with LP ( = wt per cent P in slag/wt per cent P in Si) between 0.1–0.3. The distribution coefficient of boron was measured to be between 1 and 2. The crucible material used had an influence on the phase compositions and slight influence on the distribution coefficients of boron and phosphorus. The experimental results provided new accurate data when considering applicability of slag treatment as a technique for Si refining and Si PV cell recycling.

Jun 19, 2024

By E C. F Hamman

Sunrise Dam Gold Mine is a large open pit mine 730 km NE of Perth, Western Australia. Contract mining commenced in the open pit in September 1996 in lake clays and saprolites with the first fresh rock mined late 1999, and the underground starting the first decline in October 2003. By May 2007, over 150 million cubic metres of material had been mined and the pit was 360 m deep with 80 m remaining before reaching the planned final depth in early 2008. A final cut-back in the northwest will commence in late 2007 with open pit mining in the Mega Pit expected to conclude in late 2010. The challenges of developing the pit can be divided into three phases:Soft materials û mining was in multiple staged pits and cut-backs in lake clays, saprolites, weathered material. The varying characteristics had a significant impact on mining methods and slope stability. Structural û mining was gradually exposing more fresh rock and the drive was to understand how major structures and lithological contacts impact on local and large-scale stability. This had a significant influence on mine design and scheduling. Slope angles û achieving the final slope angle is critical. This is done through application of high standards of final wall establishment and proactive geotechnical hazard identification and management. This includes dealing with the rapid rate of descent, interaction with underground excavations and managing rock fall risk. The paper discusses each of these phases, highlighting the geotechnical controls implemented to date, looking at their success and impact on mining.

Jan 1, 2007

By N Clarke, J Hunt, A Barros, L Keeney

The Gramalote orebody is a large low-grade gold deposit situated in the San Roque municipality, 124 km north-east of Medellin in Antioquia, Colombia. It is jointly owned by AngloGold Ashanti (AGA) and B2Gold and is currently in Feasibility Study phase. In 2013 AGA requested CRCORE to undertake a preliminary study of the potential application at Gramalote of pre-concentration by screening, part of the Grade Engineering suite. 160 samples of coarse assay rejects (-3 mm) were tested and showed one of the strongest responses seen worldwide to that time, suggesting that about 70% of the gold could be recovered into 40% of the mass. This was seen as potentially markedly improving the Gramalote economics. A large-scale testing program was implemented on site to follow up these results. A total of 18 samples of 17 t each were mined along a pre-existing exploration adit. A complex test flowsheet allowed size fractions to be generated from the as-received material as well as after crushing to 53, 23 and 3 mm, all from the same head sample. The procedures were designed after carrying out a heterogeneity study to measure sampling errors. The coarser size fractions were designed to study the effect of crushing on upgrade response and predict the response on open-pit run-of-mine ore. The finer size fractions were designed to investigate means of predicting the upgrade response across the orebody. The large-scale testing closely confirmed the average upgrade response as predicted from drill core assay rejects but found that only the -53 mm crushed material accurately predicted the upgrade response of individual samples. Ore geochemistry was able to usefully distinguish samples with good and poor response. A small study on drill core suggested that, for Gramalote, fine crushed material distinguishes vein associated and disseminated values but not other factors that control actual outcomes.

Nov 10, 2020

By T Baumgartl, J Burgess, B Emmerton, P D. Erskine

Large-scale open cut mining in the Bowen Basin has been undertaken for over 40 years. During this period, improved mechanical capability and economics have allowed extraction to greater depths, resulting in post-mining landforms of increasing height. Rehabilitation practitioners face significant challenges in stabilising these landforms and require a comprehensive understanding of the Bowen Basin Coal Measures strata likely to be disposed of during mining. Knowledge regarding the potential behaviour of differing spoil materials (following disturbance) provides a rationale to maximise short- to medium-term surface stability of constructed landforms by identification, salvage and advantageous reuse of cladding resources as a means to minimise erosional risks.CITATION:Emmerton, B, Burgess, J, Baumgartl, T and Erskine, P, 2016. Bowen Basin coalmine spoil classification for improved mine rehabilitation outcomes, in Proceedings Life-of-Mine 2016 Conference , pp 142–147 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By A Querzoli, B Williams

In late 2014 the Flinders Power Management Team was executing business improvement plans to ensure continued electricity generation until 2028 and beyond. Six months later, in June 2015, the Board announced the closure of the Flinders Power South Australian business, including the Leigh Creek Coal Mine, the Northern and Playford Power Stations located at Port Augusta and the 250km railway line. The announcement was preceded by a brief period of internal planning. A date was soon set for ceasing coal mining operations, being November 2015. The mine is unique in many ways. Located approximately 550km north of Adelaide the site has over 100 years of history and was formerly operated by the South Australian Government. Privatisation in 2000 saw the mine continue operation under Perpetual Leases from the South Australian Government. The leases included exemptions from multiple sections of the Mining Act 1971, obliging primary regulation under the Mines and Works Inspection Act 1920. The coal, being a low rank sub-bituminous brown coal, is prone to self-heating and spontaneous combustion. The mine and company town Leigh Creek were the economic and cultural heartbeat of the community. Facilities at the mine were shared by the community and vice versa. While many mines across Australia and the world enter periods of care and maintenance, few have been actively closed to the point of relinquishment (Bennett and Lacy, 2016). A swift decision to close, followed by a short mining operations shutdown period, presented significant technical and regulatory challenges for both the mine operator and for Regulators. The subsequent joint risk mapping process employed by Flinders Power and South Australian Mining Regulators was a unique real-world example of collaborative mine closure planning and execution. Lessons learnt are valuable for all mines, production facilities and for Regulators, even for those who may wrongly assume that closure is many years away. CITATION:Williams, B and Querzoli, A, 2018. Risk management for minesite closure planning and execution – start now! Lessons from the closure of the Leigh Creek Coalfield, South Australia, in Proceedings Life-of-Mine 2018, pp 68–72 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By Rintoul AH

Studies of many types and purposes are being carried out constantly by mining, minerals processing and other operating companies. Frequently, the staff requirements and special skills lie outside the resources of the operating companies, and needs arise for external consult- ing services. We examine the natures of a range of studies, the factors that influence whether they be carried out in-house or externally and then discuss the manner of execution. Aspects of both good and bad practice are highlighted in order to arrive at the basic principles that give the most benefit from study work. While the bulk of the discussion relates specifically to the execution of external studies of process plant projects, many of the observations can be applied equally to the execution of studies by one department of a large organisation for another, and also to studies of capital projects other than those involving process plant facilities.

Jan 1, 1975

By J Wiklund

The impact of non-ferrous smelters on their local surroundings is well monitored and guarded by various actors: the owners looking for profitability, the villagers looking for employment, the consumers asking for ever cheaper products and services, the government collecting taxes and all cherishing the environmental impact. Recent challenges facing the industry are various new doomsday projections: that we will be running out of base metals, that the ground we dwell on will be contaminated by the use of products. Smelters, such as BolidenÆs R÷nnskSr Smelter have a long history of increasing non-ferrous resources by recycling. It is shown that extraction and recycling of metals together with energy recovery can be integrated in a modern, profitable and clean smelter. Examples of efforts to further improve the business will be discussed such as flowsheet rationalisation, environmental investments, new feed from recycling and energy utilisation.

Jan 1, 2000

By Neill B. K, Fander H. W, Wong K, Dunlop G, O&apos

Commercial interest in refractory gold is increasing rapidly. This trend is supported by the work patterns of Amdel, where, apartfrom routine process- ing of free-milling and refractory ores, the majority of testing now includes biological and pressure oxidation studies to enhance gold recoveries. Central Mineralogical Services have examined, among other ores, an apparently unique type of refractory coating. A summary is given of experience at Optimet Laboratories, Pty., Limited. Research into nitric acid pre-oxidation, underway at the South Australian Institute of Technology since 1987, has shown significant improvements in gold recoveries, and in some cases, large reductions in reagent consump- tions. Three final-year student research projects were undertaken in 1990, jointly between the University of Adelaide and the S.A. Institute of Tech- nology. These projects involved biological pre-oxidation, pressure leaching, and Scanning Electron Microscope examination of refractory ores, and the resultant pre-oxidation and cyanidation products.

Jan 1, 1991

The Coke Ovens Laboratory at Australian Iron & Steel, Port Kembla has been involved in the analysis of seam gases and mine airs for approximately twenty (20) years. This period has seen many developments and changes in the techniques used to the point when the current techniques are equal to other labora- tories involved in similar analyses. The laboratory has NATA registration for the analysis of mine airs and gases. Apart from routine testing of seam gases, ventilation airs and gases emmitted from coal bore cores a number of projects have been undertaken. These have served a twofold purpose, one to provide information to the customer, generally Collieries Research and Technology and secondly in developing the skills and capabilities of the Coke Ovens Laboratory. This paper discusses the development and services available at the Coke Ovens Laboratory for the analysis of gases and airs from collieries.

Jan 1, 1983

Two main aspects need to be considered when analysing a potential petroleum development project. Firstly, an estimate of the recoverable reserves must be made, and in many instances, these reserves must serve as collateral to finance development if outside capital is required. Secondly, the likely production profile and cash flow has to be established, and this cash flow then must meet debt service require- ments and in addition generate the required profits. In making these crucial deter- minations, the impact on the project of a wide variety of risks has to be analysed. A computer model, which represents the project in its entirety, is a great aid in determining project viability. Such a model requires imput from geologists, engineers and economists, and interpretation of the model must also be a joint effort. Communications, and inter react ion amongst individuals and disciplines is essential if the best answers are to be obtained

Jan 1, 1983

Geomechanics is one of the more specialised aspects of site supervision on a major tunnell- ing project. The controlled deformation of a rock mass as a result of tunnelling and the knowledge of loading of temporary and permanent underground supports are important for safe, economic construction. These basic parameters depend on the construction method and sequence and the geological conditions through which a tunnel is driven. Thus geomechanical monitoring during the construction phase provides feedback to a design team and allows any revisions to a design to cater for local conditions not revealed by earlier investigations. Detailed geological mapping is an integral part of geomechanics in the construction phase. It serves as a monitor on pre construction predictions and also forms part of the as- constructed record. If conventional excavation-techniques are adopted, geomechanics can provide a service of blast' vibration monitoring of surface structures in urban areas.

Jan 1, 1976

By Dunstan N, Valentine C

Gas power was first used on the Sons of Gwalia mine in January 1911, when a twin-cylinder Crossley engine of 167 hp was installed to belt-drive a 112 kw 550-volt ac generator. This engine was connected with a No 8 Crossley up-draught suction gas producer, using mulga charcoal as fuel.A second Crossley engine, of 400 hp direct-coupled to a 550-volt ac generator, was installed in 1912, and operated by a down-draught wood producer.This was followed by a large Kynoch twin tandem four-cylinder engine, rated at 660 hp, sea level, with a rope drive to the crushing and treatment sections of the plant.These engines operated until January 1921, when the plant and power house were destroyed by fire. After the fire, both Kynoch and second Crossley engines were salvaged and reconditioned and they continued to give useful service for some years.

Jan 1, 1932

By G J. Harbort, K Lam, C Sola

The relationship between the geology of porphyry copper deposits and their processing performance is an area of interest. Being able to predict comminution properties of the ore from physical characteristics and geological descriptions would allow an increase in the precision of capital cost estimates, operating cost estimates and throughput rates. This geometallurgical approach would reduce the requirements for expensive comminution tests.As the comminution circuit is the highest capital cost item in the plant and a possible throughput bottleneck, understanding the variability in hardness within the orebody is critical. A geometallurgical model allows calculation of ore hardness values in mining blocks from ore characterisation data. This model subsequently uses a combination of simulation and power-based approaches to relate ore hardness and flotation feed size to grinding circuit throughput.This paper reviews the geometallurgical models developed for seven porphyry copper deposits and discusses the strengths and shortfalls of the methodology and similarities and differences between the different deposits.CITATION:Harbort, G J, Lam, K and Sola, C, 2013. The use of geometallurgy to estimate comminution parameters within porphyry copper deposits, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 217-230 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By J Foster

The Lanfranchi Nickel mine is located approximately 48 km south of Kambalda in Western Australia. Mining first commenced in the mid-1970s under the previous owner, Western Mining Corporation Ltd. After two years on care and maintenance, Panoramic Resources (previously known as Sally Malay Mining Ltd) purchased the operation in November 2004. The site currently produces approximately 10?000 tonnes of nickel metal annually from approximately 430?000 tonnes of ore. The Ore is mined from four main orebodies; Deacon, Helmut South, Lanfranchi and Schmitz. The Helmut South orebody is situated approximately 790 m below surface and extends to a resource depth of 940 m. Horizontal thickness of the orebody ranges from 10 m to 45 m in width, with the average being 30 m. Previous mining at the Lanfranchi operations specifically the Helmut orebody, had a history of seismic activity. When Panoramic Resources acquired the operation it was decided that seismicity was going to be an issue and therefore a mining method needed to be selected that could effectively manage this potential risk. The dip of the orebody is quite shallow at 45º, with a 30º plunge to the south . The hanging-wall comprises of very weak ultramafics. Due to these factors the orebody posed several mining challenges. To safely and effectively mine the Helmut South orebody in the Lanfranchi Nickel mine, underhand cut and fill mining was selected as the most appropriate mining method. Paste fill comprising of cemented gold tailings was the backfill of choice. This paper is intended to convey some of the key learnings from the use of a mining method that has not been commonly practiced in Australia.

Mar 21, 2011

By S G. Li

Mine intelligent ventilation is an important guarantee to realise intelligent mining. It is the integration of the Internet of Things, big data, artificial intelligence, internet, cloud computing with ventilation technology, forming a complete ventilation system with intelligent perception, intelligent decisionmaking, intelligent emergency response and airflow control. In order to fully grasp the progress and trends of mine intelligent ventilation research in western China. The paper based on literature analysis and field application research, comprehensively expounds the main research and practical results of mine intelligent ventilation in western China, mainly analyses the development status of key technologies such as accurate and rapid determination of mine ventilation parameters, intelligent analysis and decision-making of ventilation and intelligent regulation of ventilation equipment, and introduces the field test or application of mine intelligent ventilation technology in western China. It lays the foundation reference for related research and improving the intelligent level of mine ventilation.

Oct 12, 2022

By P J. Hawke, M F. Flis

The Hamersley Basin of Western Australia holds significant tonnages of detrital iron deposits. Formed by a cyclic weathering and eroding sequence of nominally barren banded iron formation, they may form rich proximal accumulations of iron cemented gravels distal from any obvious hard-rock iron mineralisation. While generally small, they nonetheless represent excellent economic targets as they are near surface and easy to mine. The relatively high density of iron detritals, when compared with their sedimentary hosts, makes the gravity method the primary method of exploring for these blind deposits. Identification of possible trap sites is used as a precursor to gravity surveying, with magnetics used as an ancillary method prior to drilling. Application of the gravity method in this terrain is not straightforward. Detrital trap sites are best developed next to the spectacular cliffs that form the range fronts to the Hamersley Ranges. Precise terrain corrections and use of first vertical derivatives are routinely applied to gravity data in an effort to map every possible gravity high that may reflect the presence of a detrital accumulation. Extensions to Hamersley Iron Pty LimitedÆs BS2D deposit were discovered by the routine application of gravity. This methodology has been used to create a model by which exploration for detrital deposits continue to the present day.

Jan 1, 2002

By F C. D Michelin

Blast fumes are a significant health risk to underground workers, containing several dangerous gases such as carbon monoxide (CO), nitrogen oxides (NOx) and ammonia. To ensure safe working conditions, workers are not normally allowed to re-enter a mine until the gases are cleared. To predict if gases can be cleared efficiently, simulations can be performed to estimate the gas levels following a blast. For accurate modelling, a calibrated airflow simulation is required in addition to blast-specific parameters such as the yield rate (representing the amount of gas released per kg of explosive) and the dispersion factor (representing how quickly the gases can enter the air stream from the explosive site). Those parameters are not easily determined, as they will vary from blast to blast. Many post-blast gas recordings on mine sites were studied and the correct parameters were determined to ensure an accurate gas simulation. The variability of the results was then analysed and correlation to known parameters is suggested. Finally, recommendations on how to determine the correct parameter are presented.

Oct 12, 2022

Education for the Mineral Industry in Australia developed in an uncoordinated but effective fashion till the mid 1960's, with recognised quality in graduates, with output matching demand, and with industry needs being fulfilled. Then in the space of a further 20 years, as company structures expanded, as the number, complexity, and costs of mineral projects escalated, as educational facilities, costs and politics increased, as community perceptions and aspirations changed, as government control of minerals and education increased, and as mineral sales cycles and markets fluctuated widely, the very fabric of Australian Mineral Education fell in tatters. Extractive Metallurgy Education suffered most in this collapse, and no compre- hensive remedies have been initiated. We are all the losers. In the 1990's, the extraction of Australian minerals and metals will increase in international significance, and the education of Extractive Metallurgists must meet this need. After examining the current situation, a series of management strategies are proposed to enable Extractive Metallurgical Education to survive and prosper in the next two decades and beyond. These strategic proposals involve industry, the government, the educational bodies, and individuals, in a range of short and long term objectives, policies, and actions.

Jan 1, 1984

By R Shelton

The Big Wainihinihi River and tunnel are located on the western side of the Southern Alps of New Zealand within the active Alpine Fault zone, which marks the boundary between the Pacific and Australian Tectonic Plates. The tunnel was built over 100 years ago to supply water for gold mining, but it now conveys water from a high-energy intake to a canal that supplies three of TrustPower’s hydro-electric power stations with a combined installed generating capacity of 10 MW. Part of the tunnel passes through an unstable 50° schist slope, which fi rst suffered a wedge failure in the 1929 Arthur’s Pass Earthquake and was reinstated in the mid-1970s for hydro generation. In 2008, TrustPower’s monitoring system showed that the wedge failure had remobilised and that urgent remediation was required.Harker Underground Construction (Harker) was awarded a design-build contract to restore the tunnel to service by tunnelling a new central section. Their geotechnical engineers, Peters and Cheung, reviewed the tunnel’s stability and proposed a new, safer tunnel alignment, deep behind the failure wedges. This work was based on their failure model, cost-benefit studies, and engineering geology completion mapping at the time of re-opening.Construction innovation was an important factor in ensuring the project’s success, as were detailed geological and geotechnical information, a robust methodology, strong client relationship and planning. To suit the varying rock conditions and restricted space, Harker combined a traditional drill-and-blast method with light-weight modular steel sets and timber supports to reduce construction costs and mitigate support risk. To make material handing easier in the tight conditions, a special electric locomotive was designed and built and blasting confi gurations were adapted to suit varying rock conditions in the highly fractured schist.The isolated site meant interesting and unexpected challenges, particularly communications and resources (both human and material). Despite that, the project was completed within budget, on schedule, and with no lost-time injuries.

Mar 8, 2011

By A H. Bagherieh, S Mesroghli, H Jorjani, S Chehreh Chelgani

The rare earth elements (REEs) assay and recovery in leaching processes is being determined using expensive analytical methods, ICP-AES, and ICP-MS. This paper presents a neural network model to predict the effects of operational variables on the lanthanum, cerium, yttrium, neodymium recovery in the leaching of apatite concentrate. The effects of leaching times: ten to 40 min, pulp densities: 30 to 50 per cent, acid concentrations: 20 to 60 per cent and agitation rates: 100 to 200 rpm were investigated and optimised on REEs recovery in laboratory at a leaching temperature of 60¦C. The obtained data, on the laboratory optimisation process were used for training and testing of a neural network. A feed-forward artificial neural network with 4-5-5-1 arrangement, was capable of estimating the REEs leaching recovery. Neural network predicted values were in good agreement with the experimental results. The correlations of R = 1 in training stages, and R =  0.971, 0.952, 0.985 and 0.98 in testing stages were results for Ce, Nd, La and Y recovery predictions respectively and that theses values are considerably acceptable. It was shown that the proposed neural network model accurately reproduces all the effects of operation variables, and can be used in the simulation of a REEs leaching plant.

Jan 1, 2008