Search Documents

By Y. C. Liu

Both the habit plane of martensite and the orientation relationship between the matrix and martensite platelets of different habit planes have been investigated in binary titanium alloys with molybdenum, chromium, and iron. The effect of the mode of deformation on the martensite habit plane was studied. A micrograph of an exposed mar-tensite platelet is presented. IN the study of martensitic transformation in Ti-Mn alloys,' two martensite habit planes—{334), and {344)8—were reported. The {334), habit was also observed in unalloyed titanium upon transformation,' although there is disagreement with respect to the exact indices. The other habit plane, {344),, has not been reported in martensitic transformation in any other alloys. The present investigation was made to determine whether other binary titanium alloys with P-stabil-izing elements would exhibit a crystallography of transformation similar to that of Ti-Mn alloys. Furthermore, since martensite platelets can be induced by deformation under certain conditions, it was of interest to investigate whether the mode of deformation, compressive or tensile, would influence the formation of martensite platelets on a specific plane in an alloy system which possesses two martensite habit planes. Experimental Procedure The material used for the preparation of the binary alloys of iodide titanium with molybdenum, chromium, and iron had the following purities: 99.99 pct iodide titanium, 99.9 pct molybdenum, 99.423 pct chromium, and 99.9 pct iron. The compositions of alloys listed in this paper are in nominal weight percentage. All specimens used were prepared and treated according to the procedure described in reference 1, unless stated. For the subzero temperature treat,ment the following experimental schedule was followed. After specimens had undergone the grain-growth treatment, they were quenched into an ice-water bath and were then metallographically examined. In specimens of higher alloy content, no martensitic transformation was observed. In those in which mar-tensitic transformation did occur, only specimens in which the martensite platelets existed as fine needles in localized regions were used. All specimens were reannealed 17 hr at 1200°C, quenched into ice water. and the capsule was broken. They were held in the ice water for from 5 to 10 sec, then transferred to a liquid-argon bath. This stepped quenching procedure was found to be more efficient than direct quenching into liquid argon. In the latter case, as soon as the hot specimen was immersed in the liquid argon, a protective, insulating layer of argon gas formed, and the specimen continued to glow vividly in the bath for some time. In the study of the habit behavior of martensite produced by deformation, specimens were deformed at room temperature either by compression, tension, or rolling. Martensite habit planes were determined by the two-surface analysis procedure described in reference 1. A stereographic net of 153/4 in. diam was used throughout the investigation. The method for determining the orlentation relationship between martensite and the matrix follows that used by Greninger and Troiano.' A diamond-polishing table with its auxiliaries was used in order

Jan 1, 1957

By R. S. Olson

An analysis of the wash thickener-two stage filtration circuit was undertaken to quantitatively describe the circuit performance. On the basis of information developed in this study, the factors of major importance in reducing soluble loss are: filter wash, wash zone size, filter capacity, filter feed pulp dilution, blow back, filter cloth, water to repulp, water to primary wash, water to feed pulp and thickener underflow. The wash thickener-two stage filtration circuit has been used in many hydrometallurgical plants to separate solute from leach solids. As many as 20 to 30 plant operating variables determine the performance of the wash circuit and hence the soluble loss. The complex relationships of these variables, with each other and with soluble loss, make the evaluation of their effect on mill performance difficult. An analysis of this type of circuit was undertaken to quantitatively describe the circuit performance. THE CIRCUIT The diagram in Fig. 1 represents the operation of the wash thickener-two stage filter circuit. This circuit provides for counter current, cross current or for a combination of countercurrent-cross current operation. The feed pulp stream, J, is intended to include any solution or water, other than primary and secondary filtrate, which enters the wash thickener. Except for filter washing, the operations in the circuit are simple mixing operations which can be described by material balance. The concentration of solute in the filtrate and cake solution after application of wash liquor cannot be described by simple material balance. The displacement washing equation, derived by Rhodes1 and extended by Choundhury and Dahlstrom,2 appears to best describe this case of miscible displacement in porous media. In a useful form, it is

Jan 1, 1963

By E. T. Turkdogan, P. Grieveson, J. F. Beisler

Jan 1, 1963

By W. L. Dumoulin

A RATHER detailed description of the entire plant and leaching process was given in a paper recently presented to the Institute,1 so this paper will cover briefly only the crushing practice of the New Cornelia Copper Co. for the year, 1918. The ore, which is mined by steam shovels and loaded in side-dump cars, passes through two crushing plants. These crushing plants were constructed to crush the ore required by a leaching plant of 5000 tons daily, capacity, during a crushing period of 16 hours. The primary plant reduces to less than 3 in. (76 mm.) and the secondary plant, to ¼ in. (6.35 mm.), which is sufficiently fine for satisfactory percolation of solution through the ore in the leaching tanks, and to give good extraction. The ore is then conveyed to the leaching tanks by a system of 28-in.. (71-cm.) belt conveyors. On the way to the leaching tanks, it passes through an automatic sampling plant, where a 1-per cent. sample is taken. From the primary crushing plant, the ore is conveyed by two 36-in. (91-cm.) belt conveyors to a 10,000-ton steel storage bin, with a reinforced-concrete flat bottom. The ore discharges from the bottom of this bin onto four 20-in. belt conveyors, which deliver it to the four units of crushers in the secondary crushing plant. There is no storage bin between the mine and the primary crushing plant. The ore breaks very coarse, is very hard, and contains a great many boulders, some as large as 4 ½ by 4 1/2 by 10 ft. (1.3 by 1.3 by 3 m.). Jams form in the bowl of the coarse crusher in the primary crushing plant, as a consequence, and are freed by means of an immense steel hook operated from a 40-ton electric traveling crane.

Jan 8, 1919

By L. Moyd, P. Moyd

The first commercially available portable gamma ray-neutron beryllium detector, the Rerylometer, was developed by the same group that developed the first practical portable scintillation counter, the Scintillo-meter. This group includes Professor George Brownell, of the Geology Department of the University of Manitoba in winnipeg, and his associates, K. I. Roulston, R. w. Pringle, and R. L. Funt, of the Physics and Engineering Departments of the University of Manitoba. A prototype model was tested in the field by Dr. Brownell during the summer of 1958. Commercial production was undertaken shortly thereafter by Nuclear Enterprises Ltd., of Winnipeg, and a license for manufacture and distribution in the U.S. was granted to Isotopes Specialties Co., of Burbank, California, a division of Nuclear Corporation of America. Early in 1959, we were retained by the 'Mining Division of Minerva Oil Co. to Legin a search throughout North America for minable deposits of beryllium, and to train members of their permanent staff to continue the program. The project included literature sur-veys, interviews with members of various federal, state, and provincial agencies, scanning of our own collection of suites of specimens from various mineral occurrences, and the examination of deposits in the field. The value of a beryllium detector to this program was obvious and arrangements were made to procure one as soon as possible, which resulted in our obtaining and using the first instrument that was produced commercially in the U. S. In addition to the commercially available Berylometer, Mr. William Vaughan and his associates, of the U. S. Geological Survey Geophysics Division, in Denver, have developed and tested several experimental instruments based on the same principles. DETECTOR Principles The detection of beryllium is based on the fact that "hard" gamma rays (1.6 MEV and geater), such as those produced by Antimony convert ordinary beryllium (Be9) to Be8 , with the release of a neutron. The neutrons are counted by a scintillator designed to favor neutron responses while suppressing those of gamma rays. 'The instrument is completely selective for beryllium. No other element can interfere. Instrunlentation The Rerylometer itself, which is cylindrical, is about 8 inches in diameter, 13 inches high, and weighs about 11 pounds. (Figs. 1, 2). The principal components include: 1. A disc of wax to moderate (or "thermalize") neutrons. 2. A boron-enriched polyester-zinc-sulphide fluorescent screen. This material produces strong flashes when struck by thermalized neutrons but only weak flashes from gamma rays. 3. A photomultiplier tube. 4. An electronic circuit, complete with one srnall 71/2-volt dry battery. The photomultiplier tube and electronic circuit convert neutron flashes to electrical impulses, but gamma ray effects are almost

Jan 1, 1961

By C. G. Dunn, P. K. Koh

The primary recrystallization textures of 11 single crystals cold rolled 70 pct were determined. The effect of crystal orientation on recrystallization behavior was investigated also and found to be large. An exception was found to the relationship that strong components of the recrystolliza-tion texture are rotated from the cold rolled texture by 30° about <110> axes, but generally this relationship was found to hold quite well. Evidence supporting oriented nucleotion was found and discussed in terms of probable active slip systems and <110> edge dislocations. THE present paper is one of a series&apos;.&apos; on recrys-tallization phenomena in cold rolled 31/4 Si-Fe single crystals and is mainly concerned with the textures produced on recrystallizing from stable end orientations. Data for the cold rolled textures of the crystals used have been reported by Koh and Dunn." Their results showed that the sharpness of the cold rolled textures varied throughout the range of stable end orientations and that the tendency to re-crystallize was related to the sharpness of the cold rolled texture, wherein the rate of recrystallization increased and the size of recrystallization grains decreased with decreasing sharpness of the cold rolled texture. In the project under consideration the cold rolled crystals involved a range of initial orientations that, together with those studied earlier,&apos; provide information on several points. The first point is whether the recrystallization texture from a (111) [112] cold rolled texture, a stable end orientation that can be approached from different directions, correlates in any way with the initial orientation before cold rolling, or whether the recrystallization texture is entirely determined by the observable features of the cold rolled texture. The second point involves a preliminary study to see if the main components of the recrystallization textures correlate with the most probable active slip systems. The third point is to determine what effect departure from slip on one slip system has on the tendency to recrystallize. Experimental Procedure Nine specimens from a previous investigation and two additional ones from thicker stock (lot D) but of similar composition to the others were used in the present work. The latter two crystals, like the nine, were cold rolled to a reduction in thickness of 70 pct and the amount of widening was determined. Depending on their primary recrystallization behavior, the cold rolled crystals were given short or long anneals at temperatures of 980°C or higher. Table I summarizes the data on initial orientations, the textures obtained by cold rolling, and the anneals given to provide samples for the present work. Fine grained specimens were thinned to 0.002 in. thickness and placed in an integrating specimen holder. Chart recordings using a transmission X-ray method and MoKa radiation were obtained for diffraction from (110) planes. This method,&apos;,3 which gives data for all of the pole figure except a central region of 30" radius, proved sufficient to give generally five, and sometimes six, of the six possible pole concentration areas of any one component of the texture. These data, therefore, were generally adequate for a positive identification of each component present. The first texture obtained for specimen B-2 was poorly defined because of too coarse a grain structure and therefore too few crystals in each component for satisfactory X-ray reflections. The same

Jan 1, 1957

By D. N. Dietz

Jan 1, 1969

By P. T. Allsman

INTRODUCTION The honor of being the recipient of the Mining Society&apos;s Daniel C. Jackling Award for 1966 imposes on me the responsibility to search for the subject that I would be best qualified to discuss. It seems that my experience in the mineral industry — nearly 15 years in private and 30 years in public employment — should uniquely qualify me to comment upon the relationships between the mining industry, mineral engineering as a profession, and government, and the changing economic, technologic, political and social changes that dictate their relationships. Such conditions, the increasing knowledge of the world mineral resource base, the greater demands of an expanding population with a rising standard of living, shall be evaluated with respect to our profession — mineral engineering. In all of these forty or so years, I have been in close touch with many phases of the mineral and energy resource industries, especially those of the United States. Particularly during the past 10 years, I have had a ringside seat at the "goings on" in Washington. During all of this period I have observed and analyzed many of the problems of the industry and its relations with the government. During the past few years, I have had increased opportunity for doing research and have found a need to learn something about the mathematical techniques that are undergoing such a revival since electronic computers were developed. One of these techniques is multivariate analysis, which is a system for correlating a large number of complex variables. By applying this technique to the seemingly chaotic present-day situation, there emerges a course of steady improvement in the minerals resource industries that wars, depressions, and political strife have failed to obstruct for long. In short, I advocate a need for new concepts in mineral engineering to cope with the changes, pos- sibly adding many more specialized areas on one end of the spectrum, and broad engineer-generalist approaches at the other. The meeting place shall be where the intricate mineral resource problems at the frontier of knowledge merge into the socio-techno-logical problems of the world. HISTORICAL INVOLVEMENT OF GOVERNMENT IN MINERAL RESOURCE PROBLEMS Involvement of government in mineral resource problems undoubtedly is as old as government itself. But passage of the Mining Act of 1866, superseded by the Act of 1872, was the first major entry of our Federal Government into the problems of mining. Passage of the law was necessary to resolve many conflicting claims and disputes in mining. The General Mining Law of 1872 and the Mineral Leasing Laws of 1920 apply to millions of acres of public lands and to certain privately owned land on which the mineral rights have been reserved to the Federal Government. The extensive involvement of government in the mineral industry business today often comes as a shock to the mineral engineer who has begun to climb the ladder to the top in his company. He is often poorly prepared to cope with the situation and becomes frustrated and even hostile. Better knowledge of the role of government perhaps would ease his situation. In our political system, private industry is responsible for producing minerals. To make certain that the production is adequate for a peace-time economy, and to guarantee the Nation&apos;s security in an emergency, the Federal Government finds it expedient to develop policy and engage in regulatory, educational, and research activities. A few examples will illustrate the varied role of government in relation to mineral problems. In varying degrees many agencies of the Executive Branch of Government have responsibilities that influence the functioning of the mineral and energy industries. In addition, of course, Congress, the Judiciary, and State and local governments exercise great influence. The Department of the Interior is primarily responsible for activities to promote the development and conservation of mineral and fuel resources, and the

Jan 1, 1967

By J. E. Campbell, A. W. Wesner, M. Pobereskin

This paper summarizes the results of an investigation sponsored by The Coates Steel Products Company. The objective was to determine the relative effects of certain chemical and physical properties on the wear resistance of grinding balls when grinding cement. In making this study, a number of types of balls were used in both dry and wet grinding in commercial ball mills. The radioactive-tracer technique was used in separating the test balls from the rest of the mill charge and in sorting the different types of halls that were all tested at the same time for each of the grinding operations. PROCESSING OF GRINDING BALLS In order to determine whether the properties of grinding balls, namely, composition, microstructure and hardness, can be related to the rate of wear, the halls used in this study were selected to represent various combinations of these properties. It was recognized that the mechanism of wear was not the same in the wet mill as in the dry mill. Therefore, the types of balls tested in each of the two environments were not necessarily the same. However, all of the types of balls evaluated in the dry mill were tested simultaneously for one time period, while those evaluated in the wet mill were tested simultaneously for three different time periods. All of the test balls were separated from the charge when the mill was dumped. All of the balls were of 0.940-inch diameter when charged, and all but the regular production balls were finish ground to this size to eliminate the decarburized surface layers. The steels and processing methods used, as well as the micro-structures and hardness levels of the balls, are described as follows: Regular production forged SAE 1095 steel balls were used in both the wet and dry mills. They were forged to a nominal diameter of 0.940 inch and quenched in oil from the forging temperature. Each retained a partially decarburized surface layer from the forging bar stock; the maximum depth of this layer was about 0.030 inch and the decarburization was negligible where the ball was sheared from the bar. The hardness at the surface was 40 to 46 Rock-well C in the partially decarburized area and 57 to 62 Rockwell C in the areas not decarburized. The hardened zone extended to a depth of about one-third of the radius. Below the decarburized layer, the hardened zone consisted primarily of hard as-quenched martensite with varying amounts of retained austenite. This structure changed to fine pearlite at a depth of about one-third of the radius. In order to eliminate the effect of the decarburized layer, a set of production balls of SAE 1095 steel was forged to about a 1-inch diameter, quenched in oil from the forging temperature, and ground on ball-bearing grinding equipment to a 0.940-inch diameter to remove the decarburized layer. The balls&apos; hardened zones were similar to those in the previous set. The hardness of the finished surfaces was 52 to 60 Rockwell C. A slight amount of decarburization apparently remained after the removal of about 0.030 inch from the surface. Balls of this type were tested in the dry mill only. Another set of forged SAE 1095 steel balls of 1-inch diameter was heated to 1500 F and quenched

Jan 1, 1961

By A. J. Terrones

THE classical papers on contact metasomatic deposits by Lindgren on the Clifton-Morenci district,&apos; by Barrell on Marysville, Mont.,&apos; and by Gold-schmitt on the Oslo district, Norway,&apos; laid the foundation for understanding of the importance of separating the metamorphic process from the subsequent metasomatic stage. Knopf&apos; made a big step forward by recognizing that sulfide ore minerals are invariably younger than silicates and by further stressing the importance of structural control" in ore finding. Some years later Harrison Schmitt" fought the idea that contact metasomatic deposits are erratic, irregular, bunchy, economically marginal, and of small size, concluding that these descriptions have little factual basis. He emphasized the importance of detail mapping and careful geological study as fundamental requirements for a better understanding of these deposits. This article presents a comparative description of the structural features at the Magistral, Antamina, Morococha, Vilca, Ferrobamba, Katanga (Quibio), Tintaya, and Huarca contact deposits (Fig. 1). Further, it will describe how these structural features controlled the emplacement of the intrusives, their shape, distribution of metamorphic and metasomatic halos, and sulfide deposition in post-skarn structural channelways. Finally, the modifications introduced by a superimposed hydrothermal stage recognized at some localities will be discussed. Primary exploration and careful sampling of recognized structural targets were instrumental in outlining the copper ore potential at the Antamina and Tintaya districts, thus proving the benefits and reward of careful geological examinations in this type of deposit. The Magistral District: This district lies in the Province of Pallasca, Department of Ancash, in northern Peru, at 8o 16&apos; S and 77" 47&apos; W. High to medium grade copper orebodies in garnetite, bordering a quartz monzonite stock, are exposed at the bottom of a glaciated valley in the western slope of the Andes at 4250 m (14,000 ft)* elevation.

Jan 1, 1959

By C. W. Spencer, J. T. Smith

GRAIN-BOUNDARY surfaces are penetrated by a liquid phase when the liquid-solid interfacial tension is less than one-half the tension of the grain-boundary surfaces. Grain growth may occur in the presence of this liquid phase. burke1 reports that grain growth of this nature has been observed in two-phase ceramic systems. He suggests that the presence of a grain-boundary liquid may accelerate or decelerate the

Jan 1, 1963

University of Alabama University, Alabama Mining and Metallurgical Society WILLIAM R. HIGGS, President ROBERT E. MEAD, Secretary J. R. CUDWORTH, Faculty Sponsor MILTON H. FIBS, Counselor University of Arizona Tucson, Arizona Miners&apos; Society LEE BLESSING, President R. W. CORY, Secretary E. P. MATHEWSON, Faculty Sponsor B. R. HATCHER, Counselor University of California at Los Angeles Los Angeles, California Student Chapter, A.I.M.E. ARCHER WARNE, President ROBERT JOHNSTON, Secretary E. K. SOPER, Faculty Sponsor EMILE HUGUENIN, Counselor Colorado School of Mines Golden, Colorado Student Chapter, A.I.M.E. J. Ross REED, President ANDREW PERRY, JR., Secretary J. BURNS READ, Faculty Sponsor A. W. NEWBERRY, Counselor

Jan 1, 1936

Thomas H. Beddall, so we are informed by Major J. B. Carlock, has been promoted and is now Adjutant of the 1st Battalion, 1st Gas Regi¬ ment. He was awarded, last summer, the Croix de Guerre. R. A. Bull. See letter in Proceedings of Milwaukee Meeting. Captain Stanley C. Bullock&apos;s record since entering the service is given as follows in a letter recently received from Mrs. Bullock: Resigned position of mine manager in Chile in November, 1915, to return to England to obtain commission in Royal Engineers. Joined Officers&apos; Training Corps, Dec. 20, 1915. Commission gazetted, Jan. 27, 1916, 2d Lieut., R. E. Landed in France, Feb. 6, 1916. Posted to 179th Tunnelling Co., R. E. Took part in following battles: Somme, 1916; Ypres;1917; Arras, 1917; Somme, March and July, 1917; Messines, 1917. Gazetted: Acting Captain, July 11, 1916; Temp.-Lieutenant, Oct. 26, 1916; Captain, Sept. 29, 1918. Awarded Military Cross, Jan. 1, 1918, for conspicuous bravery and devotion to duty under a heavy enemy gas bombardment, when, by his example and perseverance in spite of every difficulty and obstacle, mining work was successfully completed which was vital for the success of the operations. The Cross was presented to Capt. Bullock by the King, on Sept. 25, 1918. First Lieut. J. J. Cadot, in a letter sent to Mr. H. `V. Hardinge from France, says he has been at the "Front." He also mentions that the Boche "is a good sprinter."

Jan 12, 1918

By H. L. Miaw, A. M. Gaudin, D. W. Fuerstenau

A quantitative method for evaluating density of slime coatings has been developed and applied to formation of iron oxide slime coatings on quartz and on corundum. Slime coating density is related to flotation recovery and to properties of the electrical double layer at mineral surfaces. IN spite of considerable study, the nature of slime coatings in flotation is still not completely understood. However, phenomena that control floc-culation and dispersion of colloidal systems are now interpreted in terms of electrical double layers.",&apos; Colloids will flocculate even though the particles carry the same charge, but when two dispersed colloids of opposite charge are mixed. flocculation ensues even more rapidly. Analogous phenomena seem responsible for slime coating on minerals in flotation systems. To shed new light on the issue it was considered desirable to devise a tool that would measure slime coatings. The usual method has been to examine photographs of presumably representative surfaces, after. an intervening washing in running water. But such an examination is non-quantitative, and the changes in chemical environment represented by the washing may have removed the slime coatings that existed during flotation. To provide the possibility for a correlation with electrical double layer phenomena, the experiments were made with quartz, corundum, and iron oxide, for which elec-trokinetic data are available.&apos;-" Since the properties of the electrical double layers of these oxides depend on the pH of the solution, pH will be the most important variable. Furthermore, because the zero point of charge for silica, iron oxide, and alumina occurs at pH 3.7, 8, and 9.5, respectively, the relative charge on the slime and mineral can be changed over wide ranges. Because of its practical importance in quartz flotation, iron oxide powder was chosen as the slime. Also, its uniform composition, contrasting color, and ease of analysis make experimentation simple. In this investigation, correlation was sought between the effect on flotation recovery of slime addition and slime coating density. Materials and Methods Details are available in a thesis by Miaw." The quartz was selected from pure Brazilian crystalline quartz, crushed, sized (65/150 mesh) acid-cleaned, washed, and stored in conductivity water. The corundum (synthetic alumina of high purity prepared by Linde Co., Chicago) was crushed, sized (65/100 mesh) deslimed, boiled in nitric acid, washed, and stored in conductivity water. The iron oxide slime, reagent-grade ferric oxide (—400 mesh) from Allied Chemical & Dye Corp., was heated to 160°C, cooled, and stored in a vacuum desiccator. In the electron microscope the slime particles appeared to be about 0.3µ in size, but their large specific surface (87,900 cm per g, by gas-adsorption method, using krypton) suggests that the actual particles are smaller than 0.3r. Had they been perfect nonporous spheres, they would have had a diameter of 0.13µ.

Jan 1, 1959

By AIME AIME

A DOCUMENT of progress and of great interest to engineers is the report of the Military Affairs Committee of &apos;the Engineering Council, which has just been accepted and sent to the secretary of War. It provides .a plan whereby civilian engineers holding commissions in the Reserve Corps may; with their con- sent, be called into service of the army during peace at any time, either with troops in the field or in a consulting capacity on any government engineering work. The Military Affairs Committee finds ample authority in the military bill passed by Congress on June 4, 1920, for this arrangement and also for extending the privilege to military engineer, officer-s of the regular army to engage in civilian work during times of peace. It is hoped that the Secretary of War will adopt the suggestions and put the program outlined into effect. This is a constructive piece of work comparable to the efforts of the military Committee before the war which developed so much in the way of preparedness, particularly in the program of military lectures which, held in the auditorium in the Engineering Societies Building, became so popular that each lecture had

Jan 1, 1920

Lieut. Maxwell E. Erdory, now with the Army of Occupation in France, writes as follows: "The 602d Engrs., many of whose officers are members of the Institute, started its active service in France at Avocourt, where we built a road across `No Man&apos;s Land.&apos; This road from Avocourt to Montfaucon started us on a career of road building which lasted from Sept. 26 to Nov. 9. The engineer in war has no working hours. Our first job meant 50 hr. continuous work, a layoff of 4 hr. and 18 hr. more. That was our initiation in this war game. "Back in the States we practised building trenches, dugouts, and underground shelters of all sorts. In France we were unfortunate enough to come upon the scene when the so-called open warfare started. That made all the above unnecessary. Roads was the cry and our job was to see that all the artillery got their roads and got over them. "I might mention here that the roads of France, which were in excellent condition except for numerous shell holes, w re one of the leading factors in the rapid termination of the war. "We built a narrow-gage railroad from Romagne to Landre St. George which cost us a few men. At Stenay we did our first bridge building. We built nine bridges across the Meuse, capable of carrying tanks, in 18 hr. The next day the American army crossed these bridges on their way to Virton, Belgium, and the Rhine. " Our course from Virton, Belgium, took us through Longwy, Musson, and Athus, in which towns I inspected the steel plants. In Musson as well as Longwy the Germans had destroyed most of the blast furnaces. This destruction began in August, 1917. In Athus the furnaces were in good condition, the Germans having removed all motors land electrical apparatus, rendering the plant inoperative. I have taken several photos of interest of these plants. "It is but fitting that I say that the engineer in this war has contributed much toward its success but the "Doughboy" is its hero and we engineers one and all say "All hail the Doughboy."

Jan 2, 1919

By H. E. Hawkes, D. A. Barr

Time variations in the copper content of the sediments of streams draining mineralized areas were studied in two areas of contrasting climatic environment, one in northern and one in southern British Columbia. In each area, samples were collected and observations made of rainfall, stream discharge and air and water temperature at intervals throughout the summer season. Samples were analyzed for total and cold-extractable copper. Results showed a weak inverse relation between cold-extractable copper and discharge in two out of the three test sites in the southern area, and a decrease in ratio of COld-extractable to total copper over the duration of the test period at a highly anomalous site in the northern area. In suspended rock flour resulting from glacial erosion of mineralized rock in the northern area, virtually all the copper was found to be soluble in cold, dilute hydrochloric acid. None of the variations observed is sufficient to cause serious problems in geochemical sediment surveys. Systematic collection and trace analysis of stream sediments has seen wide application in recent years as a method of primary prospecting in primitive areas. Common practice is to collect fine-grained samples of sediment either from the active channel or from the flood plain near the channel. Samples are dried, sieved and the -80-mesh fraction analyzed after breakdown of the sample by a relatively strong attack, such as by fusion or by treatment with hot perchloric acid. Drying, sieving and rigorous chemical attack requires established facilities, either in a well equipped central laboratory or in base camp. Thus analysis for total metal involves a substantial delay from the time the samples are collected until the analytical data can be reported. An alternative system uses a cold aqueous extrac-tant in place of the hot acid or flux.4 Advantages of the cold-extraction techniques are that kits can be prepared for use directly at the sample site and that, in some problems, the patterns in cold-extractable metal, usually abbreviated cxMe, are more useful as ore guides than the patterns in total metal.&apos; In the course of operational geochemical sediment surveys, a problem that has come up repeatedly is failure to reproduce anomalous values or patterns by resampling the same areas. The mystery of the vanishing anomaly has led to speculation as to whether there is a significant variation in the metal content of sediment samples with the weather or with the time of year. Review of the published literature shows that a number of experiments have been carried out on time variations in the metal content of stream water.1,2,5,7-9 The only published report on time variations in stream sediments that has come to the authors&apos; attention, however, is by Govett,3 working in Northern Rhodesia.

Jan 1, 1963

By R. A. Wood, R. I. Jaffee, H. R. Ogden, D. N. Williams

Strain-induced porosity has been found to occur in titanium and other materials at tensile strains greater than the uniform elongation of the material. Porosity in titanium increases with increasing strain and temperature, being most severe at 300° to 800°F. Strain-induced porosity is believed to be a normal part of the mechanism of deformation in ductile materials. DURING the past few years there have been numerous references to the occurrence of voids in laboratory test specimens of metals subjected to strain.l-7 These voids have been referred to as intercrystalline cracking, strain-induced porosity, intergranular cav-itation, voids, and porosity. They appear to occur at grain boundaries or interfaces, and are generally associated with large amounts of strain and have been found mostly in creep specimens and to a lesser extent in tensile specimens. Because the phenomenon does not occur unless the material has been strained,

Jan 1, 1960

By E. J. Dulis, A. Kasak, R. C. Westgren

The potential of uirought tungsten- and tantaluw-rich alloys of the W-Ta-Mo-Cb system was investigated for high-strength structural applications above 2500° F. Appreciable strengthening of tung-sten and tantalum—essentially attributable to solid-solzction effects—was obtained with binary, ternary, and quaternary alloys. Tensile strengths as high as 67,000 psi were achieved at 3000 OF. ThE quest for wrought structural materials which possess good strength properties at temperatures above 2000°F has led to a considerable research effort during the past decade. In addition to exploring the potential of various high-melting-point refractory metals (such as molybdenum, columbium, tantalum, and tungsten) for very high-temperature structural applications, alloy-development programs have been undertaken to achieve greater strengths than could be achieved with unalloyed refractory metals. The methods of strengthening refractory metal alloys have included both solid-solution and dispersion strengthening. General relationships among the relevant properties (melting point, recrystallization temperature, and high-temperature strength) of refractory metals indicate that the highest strengths at temperatures of 2500°F or higher would be obtained with tungsten-or tantalum-base alloys. Therefore, the present investigation was undertaken to determine the high-temperature strength potential of solid-solution strengthened alloys based on the binary system W-Ta; to effect further strengthening, minor additions of molybdenum and columbium (at the 6 and 12 pct levels) were made. The portion of the W-Ta-Mo-Cb quaternary alloy system of interest is shown schematically in Fig. 1. The component metals—W, Ta, Mo, and Cb—have a bcc structure at all temperatures, and their binary systems are mutually completely soluble.&apos; Complete solid solubility in the W-Ta-Mo and W-Ta-Cb alloy systems has been demonstrated,&apos; and, therefore, it was expected that the quarternary alloys of the system would also exhibit complete solid solubility at all temperatures. In the virtual absence of contamination by interstitial elements, all the alloys would be truly solid-solution strengthened. Twenty specific compositions of this investigation included binary, ternary, and quaternary alloys of the W-Ta-Mo-Cb system as well as unalloyed tungsten and tantalum. The compositions are shown in Table I. EXPERIMENTAL PROCEDURE Consumable-electrode vacuum-arc melting with ac power was used to produce small laboratory-sized, cylindrically shaped ingots (1-1/4 in. in diameter and 2 to 3-1/2 in. long) of the twenty compositions. A furnace was specially constructed to melt as many as four electrode rods simultaneously into molds lined with tungsten or tantalum sheet. High-purity rods of tungsten, tantalum, molybdenum, and columbium were used for consumable electrodes; the diameter of each rod was determined by the desired weight percentage of the component metal in a given alloy. The details of the construction and operation of the melting furnace will be discussed in another p~blication.

Jan 1, 1964

Major William R. Grunow, in a brief account off his military services, says: "I take pleasure in informing you that since my return from France I have been stationed at Camp A. A. Humphreys, Va., and am now on duty as a Senior Instructor at the Engineer Officers&apos; Training School. While in France, I served as a company commander in the 305th Engineers and was later ordered to return to the United States for assignment to new troops. Upon arrival in the United States, I received my majority." P. F. Rodegerdts gives us the following account of his military service: "I enlisted in the Naval Reserve Flying Corps in San Francisco on Feb. 12, 1918. On February 10, I was ordered to Cambridge, Mass., where I was enrolled for the course in technical aircraft construction given at Massachusetts Institute of Technology. After successfully completing the course of instruction, I spent six weeks in practical construction of seaplanes at the Curtiss aeroplane factory in Buffalo. Following this, I was assigned to active service at Akron, Ohio, on June 22, 1918. At the same time I received my commission of ensign U.S.N. R.F. Unfortunately, I have been kept at Akron and although I have made

Jan 1, 1919