Search Documents

To allow routine measuring of the exposure of underground workers to N02 from diesel engines and residual gases from blasting. The Approach: A miniature sampler absorbs NO2 which can be measured using a simple method adaptable to both multiple automatic analyses or individual on-site analysis. How It Works: The NO2 sampler is encased in a plastic tube approximately half the length of an ordinary ball point pen and clipped to an underground worker's hard hat. Removal of the end cap activates the personal sampler. Air from the working place enters the open end and diffuses at a controlled rate down the tube interior. The diffusion rate is dependent on tube dimensions (ratio of cross-sectional area to length). The closed end of the tube contains stainless steel mesh which is coated with triethanolamine (TEA) for absorbtion of all NO2 reaching it. Other oxides of nitrogen are not absorbed. The amount

Jan 1, 1975

Agglomeration for Copper Heap Leaching Agglomeration of ore is a method which can be used to eliminate the migration of fine grained particles throughout a leach heap. Without agglomeration, fine ore particles are able to migration within the heap, clogging flow channels and producing large areas where access of the solution is poor. In order to gain the benefits of agglomeration and improve agglomerate strength even further in copper heap leaching, an economical, acid-resistant binder is needed. However, most binders have been used without any systematic reasoning. A set of novel testing methods were developed, including a soak test, percolation flooded columns, and larger long-term leach columns. The soak test compares the degree of breakdown when agglomerates are subjected to an acidic environment. While the percolation flooded columns and larger long-term leach columns evaluate the flow of leach solution throughout the ore bed. Systematic studies have been completed on a wide range of binders using these novel testing procedures. It was found that for a low grade chalcocite ore, which was rich in silica, from a southwest US mine, polyacrylamides reduced the fines migration the best in the novel soak test. The non-ionic binder, in particular, was found to reduce fines migration as much as 93 per cent. Several of the binders tested were shown to increase the hydraulic conductivities of the agglomerated ore up to 2.5 mm/sec, compared to a hydraulic conductivity of only 0.25 mm/sec when no binder was used. These binders also prevented 'slumping' of the ore, which indicates a decrease in breakdown of the agglomerates. The use of a binder also showed no interference with leaching reactions in long-term leaching experiments.

Sep 13, 2010

By Zhuofei Yang, Jidong Kang, David S. Wilkinson

The fatigue behavior of AM60 high pressure die casting magnesium alloys was studied in a straincontrolled manner. The fatigue test was interrupted every 2,000 cycles for X-ray tomography scanning. The specimen was removed to be scanned on a desktop micro-CT system. The value of using X-ray tomography in a fatigue properties study was assessed with respect to porosity, cracks and fracture surfaces. The 3D analysis and model results showed porosity could be well measured and modelled in 3D. Defects bands are made of pores under 50 µm in volume-equivalent sphere diameter. Larger pores are randomly distributed in the region between two defect bands. Observation of cracks by X-ray tomography occurs in three ways such that the 3D model gives the best illustration of crack-porosity interaction while the other two methods have better detectability on crack initiation and crack tip observation. X-ray tomography is also of value in failure analysis on fracture surfaces. By summarizing X-ray tomography data during fatigue testing and observing fracture surfaces on a 3D model, a better understanding on the crack initiation, crack-porosity interaction and the morphology of fracture surface is achieved.

Jan 1, 2014

Despite the fact that mined minerals and gemstones have allowed human beings to continuously improve their standard of living throughout the ages, mining has also been implicated in violent conflict for two principle reasons. The first is that mineral resources have been used or traded to conduct or finance violent conflict from small to large scales. The second is the substantial social, economic and environmental changes that occur in a community or a region as a result of mining activity which can either precipitate or re-awaken latent conflict. A modern complication of mining-related violent conflict is the trend for activists, international NGOs and intergovernmental organisations (e.g. the United Nations) to regard any human consequences of resource extraction in terms of Human Rights violations. Acknowledging but not labouring the Human Rights implications of mining-related violent conflict, this paper explores whether or not there is a relationship between the actual or perceived value of mineral resources and the level of violence that occurs in mining-related conflicts. Key to the investigation is a mapping exercise of mining related conflict from 2005 ? 2012: to see where mining related conflict is happening; to identify precipitant causes of mining related conflict; and, to discover what correlation ? if any ? there might be in the degree of violence and the value of the mineral(s) implicated. Findings of the analysis are presented in this conference paper.

Aug 1, 2013

By Oliver Bowles

Sandstone, a widely distributed siliceous sedimentary rock, is the third most popular building stone in the United States. It is formed by the breaking down of preexisting rocks by weathering, subsequent segregation of the detrital quartz grains into discrete deposits by the sorting action of water or wind, and finally cementation of the quartz sand into a coherent rock. The homogeneity and resistance to weathering of the resultant sandstone make it suitable for exterior construction. Its excellent wearing properties explain its popularity for flagging and stair treads. However, quarrying and dressing methods and costs are adversely affected by the abrasiveness and hardness of sandstone especially as compared to limestone.

Jan 1, 1963

By J. P. D. Strydom

The transmission of excessive vibration to the human body can cause physical stress that may result in crippling pain or permanent disability. Rock drills are known to transmit high levels of vibration that are difficult to attenuate through conventional approaches to vibration isolation. However, it can be shown that once the ISO frequency weighting has been applied, most of the vibratory effect of the rock drill?s motion is concentrated at the drill?s operating frequency. This observation opens the way for utilizing a concept known as vibration absorption, aimed at attenuating the rock drill?s vibration. In essence this entails using the inertia of a secondary vibratory system to counteract the motion of the handle. This article documents an investigation into the use of such an absorber for attenuating rock drill vibration and demonstrates the feasibility of such an approach. A mathematical model of such an absorbing handle was developed and used for design studies. Based on these investigations an experimental prototype model was manufactured and tested. A significant reduction in vibration levels could be achieved.

Jan 1, 2002

By Raymond W. Henn

The 32nd annual short course ?Grouting Fundamentals and Current Practice? was held at the Colorado School of Mines, June 13-17, 2011. The field demonstration portion of the course was conducted June 16 at Baski Inc.?s yard in Denver, CO. The full-scale field demonstration presents many types of drilling and grouting equipment in operation as well as numerous grouting methods per-formed under various field conditions. As part of the field demonstration, the class was shown the proportioning, mixing, testing and injection of various cement grout mixes into sand columns under controlled and recorded conditions. These sand column demonstrations have been conducted under controlled and measured conditions each year since 1999 as part of the short course. The sand column demonstrations were conducted prior to 1999, but with less quality control and minimal record keeping of the proportioning, mixing, testing, injection pressures and the final permeation results.

Jan 1, 2011

Ventilation network modeling in mine planning dates back at least three decades, but it is not widely accepted and/or practiced until the last decade, thanks to the advent of modern computers with their increase d speed and storage space. There are at least half a dozen such modeling software packages available on the market each with different features and acceptance. This paper compares five popular software packages,?? VnetPC Pro, MineVent, VentSIM Visual, VentGraph and MFIRE 3.0. A case study using Missouri S&T?s Experimental Mine is conducted to compare the five software packages in features, interface, output display and user-friendliness.

Jan 1, 2012

The published liquidus data on the Pb-PbS system have been correlated on the basis of one-coefficient Margules equations. Thermodynamic properties of the components of this system have been obtained, and it has also been found that the calculated miscibility gap of this system exists over a very narrow range of temperature (1041 to 1058°C).

Jan 1, 1972

A comprehensive review of ore pass records, from ten Quebec underground mines, indicated some of the limitations of available design tools to predict the occurrence of ore pass interlocking hang-ups in metal mines. The Distinct Element Method was used to perform a series of numerical experiments in order to investigate the influence of ore pass geometry, rock fragments shape and size distribution on material flow in an ore pass. Guidelines have been developed to help limit the occurrence of interlocking hang-ups in an ore pass. The proposed guidelines were evaluated with respect to field observations. Ein kompletter Bericht der Erzrollezeichnungen, von 10 Quebec unterirdischen Gruben, hat einige der Beschränkungen der vorhandenen Designwerkzeuge angezeigt, um das Auftreten Erzrolle der blockierenhang-ups in den Metallgruben genau vorauszusagen. Eine Reihe numerische Experimente mit der eindeutigen Element-Methode, wurden aufgenommen, um den Einfluss von Erzrollegeometrie, Partikelform nachzuforschen und Felsenkorngrößenverteilungen auf Materialfluss in ein Erz überschreiten. Dieses hat zu die Entwicklung der Richtlinien geführt deren Implementierung das Auftreten der blockierenhang-ups in eine Erzrolle begrenzen sollte. Die vorgeschlagenen Richtlinien wurden in Bezug auf Labor- und Feldbeobachtungen ausgewertet. Une revue de la performance actuelle des cheminées à minerai dans 10 mines souterraines du Québec a indiqué les limites des outils de conception servant à dimensionner les cheminées pour minimiser le nombre d’accrochages par enchevêtrement rocheux. Des séries de modélisations numériques, utilisant la méthode des éléments distincts, ont été réalisées afin d’évaluer l’influence de la géométrie des cheminées, de la forme des fragments rocheux et de la distribution granulométrique sur l’écoulement du matériel dans les cheminées. Cet exercice a permis de développer des lignes directrices pour le dimensionnement des cheminées afin de limiter l’occurrence d’accrochage par enchevêtrement rocheux. Les lignes directrices proposées ont été évaluées en fonction des observations effectuées sur le terrain.

Jan 1, 2003

By R. S. Dean

The brief resume of the activities of the Metallurgical Division that appears annually in its progress reports series serves a useful purpose by making available a rather comprehensive but concise recapitulation of the current work, and publications of the division. An unprecedented opportunity to attack the problem of producing ferro-grade material from low-grade domestic manganese ores effectively was provided by the act designated as Public 667 of the 76th Congress of the United States, approved June 26, 1940, which made available an appropriation for "Expediting Production of Equipment and. Supplies for National Defense." Although the funds were not immediately available to the division, good progress has been made in the, solution of the many and diverse problems presented in the studies undertaken to determine the best methods for the recovery of useful products from a wide variety of manganese ores.

Jan 1, 1941

By J. D. T. Capocchi, M. B. Mourao

The rate of reaction between iron oxides and carbonaceous materials, agglomerated as pellets, was studied experimentally by measuring the weight loss as a function of time. The effects of temperature, carbon type, inert gas flow rate, pellet size and additions (sodium. carbonate and Portland cement) were determined. It was shown that the value of the apparent activation energy can display large deviations under different experimental conditions; in the present work it was found to be 226.6 kJ/mol. The reaction with coke is slower than with charcoal, and the rate increases as the flow of inert gas in the reaction vessel decreases. Comparison of the rates for pellets of different sizes has shown that for small pellets the initial rate is faster but that it slows down at high conversions owing to the penetration of inert gas into the pellet. Additions of sodium carbonate and Portland cement increase the rate; sodium. carbonate promotes the catalysis of the Boudouard reaction, which is the slowest of the partial reactions. The increase in the rate with Portland cement is attributed to the release of water vapour

Jun 18, 1905

By H. Kazemi, M. S. Seth

The effects of anisotropy and stratification on flow behavior and production performance of oil and gas wells have been studied by numerous authors.1-3 Lefkovits et al.l studied the performance of totally penetrated, stratified bounded reservoirs with no crossflow. Others have studied a similar problem, but with crossflow; Russell and Prats2 have summarized the findings of these papers. Muskat3 studied the steady-state behavior of liquid flow for a partially penetrating well in an anisotropic system and concluded that the productivity weakly depended on the directional permeability ratios (kz/kr>0.1). Nisle4 used the classical method of point source solution to the diffusivity equation to study the effect of partial penetration on pressure buildup of oil wells in an isotropic system. He found that the theoretical pressure buildup curves consisted of two straight lines, the one at early buildup times having a slope proportional to the flow capacity of the open interval (l-d)k, and the other having a slope proportional to the flow capacity of the entire formation hk,. Later Brons and Marting5 supplemented the findings of Nisle and concluded that partial penetration gave rise to a pseudo damage, which reflected itself as a skin factor in pressure buildup calculations. Using the pseudo skin, they calculated the impairment of productivity of the production wells, which agreed well with the results of Muskat.6 Pizzi et al.,? using an electrical analog of a stratified system, concluded that a high pseudo damage resulted if the reservoir was partially penetrated. Harriss studied the optimum spacing and arrangement of perforations in cased holes. Hantush9 derived an expression for pressure distribution in an unbounded reservoir with restricted flow entry. Seth10 extended Hantush's work to a bounded reservoir. Odehl1 has studied a similar problem for steady-state conditions. The purpose of this work was to investigate: (1) the combined effects of anisotropy, stratification with crossflow, and restricted flow entry on pressure transient analysis of flow and buildup tests, (2) the feasibility of calculating the horizontal permeabilities of intercommunicating stratified systems, and (3) the pressure interference tests in such systems. Theory The partial differential equation governing the isothermal flow of homogeneous fluids of constant compressibility is given by Eq. 1: The initial and the boundary conditions are: 1. The reservoir potential is initially constant, say 4v

Jan 1, 1970

By Arthur L. Holloway, James C. Mugford

"The Underground Research Laboratory (URL) is located in southeastern Manitoba, in the Lac du Bonnet granite batholith of the Canadian Shield. It was constructed by Atomic Energy of Canada Limited (AECL) to conduct geotechnical research for the Canadian Nuclear Fuel Waste Management Program, assessing the concept of permanent disposal of nuclear fuel waste deep in plutonic rock.One of the primary objectives of the research program at the URL is to develop a nondestructive rock mass characterization method that can be used during siting, design and construction of a used fu el waste disposal vault. An experimental program was established to assess radar reflection profiling as a technique for fracture characterization in granite. The highly resistive, homogeneous nature of the Lac du Bonnet granite is ideal for the propagation of electromagnetic energy at the radar range of frequencies and water-filled fracture zones act as excellent reflectors because of their contrasting electrical properties.Radar reflection profiling was undertaken to characterize a major fracture zone located between 5 m and 10 m below Room 211 on the 240 m level of the URL. The profiling was done at a frequency of 120 MHz, on a 1m grid laid out on the bare rock floor of the room. Reflectors identified in the analog data were correlated between the profile lines, digitized, and a three-dimensional surf ace for each recognizable reflector was constructed. These surf aces were then compared with data obtained from the examination of numerous cores from adjacent boreholes intersecting the fracture zone. A very good correlation was found between the major radar reflectors and the most intensely fractured regions of the zone. Modelling studies also showed that a series of prominent shallow radar reflectors were caused by a borehole drilled close to Room 211."

Jan 1, 1990

By William J. Douglas

This document describes the development of a conventional mining equipment data base, and an approach for conducting industrial engineering studies of arbitrary mining systems employing network techniques. Data was acquired through underground time studies. Each member of a four-man field team was assigned to a specific machine during each shift for which observations were conducted. Using digital wrist watches and networks describing the man-machine interactions, all events occurring luring the course of each shift were recorded on cassette tapes. The tapes were transcribed, coded, keypunched, and validated using computerized editing techniques. The resulting data files were processed to provide statistics relating to activity durations and event frequencies. The results were used to evaluate operator, machine, and system performance for each section which was observed. Equipment, reliability, and maintainability analyses were conducted using the industrial engineering data files in conjunction with historical information collected at the mine site.

Jan 1, 1976

Jan 1, 1996

A genesis based on new developments in the physical chemistry and flow properties of colloidal substances is proposed for the pipe-like Peko orebody. The rheological behaviour of sediments is governed by the contained colloids. Remobilization of thick pasty sediment during diagenesis is regarded as an essential step in the concentration of metal dispersed in sediments. At a high concentration the sediment pore fluid is a dense gelloid such that van der Waals attractive forces between the colloidal particles exceeds the coulombic repulsion. This permits accretion of the colloids into globular clots and their fracture fragments. These have a uniform size distribution dependent upon the rate of shear, and the sediment lithifies to clotted, porphyry-like, "gritty", dolomitic or igneous-looking intrusions and flows. The physical chemical properties of natural sediment colloids appear adequate to account for ore formation.Adsorption accounts for the dispersion and retention of metal in sediments. Accretion accounts for the segregation of the colloidal materials to give the various types of clotted igneous-looking intrusive source rocks. Syneresis enables the colloids to spontaneously draw together and to dehydrate. Formation of an ordered lattice achieves a lower energy state and desorbs metals and insoluble metal compounds "particle by particle" into the escaping water of hydration and pore water. Peptization enables migration of the metal hydrosols as stable dispersions until they merge for outflow through seepage zones or water extrusion channels. Nucleation and concretion precipitate the metal dispersoids from pore waters seeping through hydrous parts of the source rock, porous beds, faults, and zones of weakness by which the connate waters leave the lithifying sediments. Gelatinous precipitated mineral matter in the ore channels is capable of thixotropic reliquefaction when disturbed by shock or movement. Local reintrusion, flowage, interveinings,brecciation, and intermixing of the materials is the result.The principles of the suggested genesis are applicable to both syngenetic and epigenetic mineral accumulations.

Jan 1, 1966

By Delahant A. B, Dworski M

From the Saranac Laboratory for the Study of Tuberculosis of the Edward L., Trudeau Foundation, Saranac Lake, New York:We are assembled to honor the memory of our friend and colleague, Donald Cummings, one of the founders and a past president of the American Industrial Hygiene Association. I deem it an Unusual privilege to have been asked to give this first memorial lecture and hope that what shall have to say may be worthy of the occasion. It is fitting that we should discuss here the subject of Silicosis to which he devoted such a large part of his life and it is doubly fitting, I think, that I should report to you an extended series of investigations carried on by his associates at the Saranac Laboratory.The subject of silicosis may seem hackneyed to this audience which is so familiar with the tried and accepted methods of prevention and control.But in spite of our efforts, the condition is still with us and unfortunately is still being produced in many places. In industries that now maintain good control of dust, fresh cases are appearing on annual re-examination, whose major exposure date back to the days before the hazard was recognized.A few new employees, with apparently ineffective upper respiratory protection against inhaled dust, develop silicosis precociously in environments that are comparatively harmless to their fellows. In plants that have relaxed their vigilance under the urgency of war production schedules, conditions again prevail that will produce, disease in the future.Silicosis acquired new interest with the announcement by Denny, Robson and Irwin(1) in 1937 that it could be prevented by the inhalation of powdered metallic aluminium. It so happened that without knowledge of their work, we at the Saranac Laboratory had for some months been conducting similar experiments with one of the hydroxides of aluminium.Quite independently we discovered that hydrated alumina would also protect animals against quartz. Our approach to the problem had been empirical; we were trying to neutralize quartz particles by coating their surfaces with an insoluble material following the lead of Kettle who in 1932 had shown that this could be accomplished with iron. He neglected to describe his method and the chemist who prepared his coated...

Jan 1, 1945

By W. G. Willson, D. E. Walsh, B. Irwin

Low-rank coal (LRC) drying processes are generally categorized by operating temperature, drying environment and type of feed (either sized or ground coal). Within these broad categories, drying processes differ according to the type of drying equipment and methods of quenching and stabilizing the dried products. This paper focuses on the produce quality of various LRC drying processes including conventional low and high temperature evaporative drying and non-evaporative, hydrothermal drying. The former may be preferred if the dried product can be utilized immediately, but moisture reabsorption, spontaneous heating and fines production during handling are problems associated with longer term storage, transportation and utilization. Methods for reducing these problems are discussed. Hydrothermal processing is an advanced technology featuring high pressure, non-evaporative drying, which solves stability problems by producing a liquid feel.

Feb 24, 1997

By Franklin M. Grynkewicz

The subject of bearing pile performance installed by vibratory hammers has been a matter of increasing study and continued controversy. A recent case study from a major bridge replacement project is discussed which provides encouraging data on the use of vibratory pile hammers as a primary means of pile installation and also presents the problems associated with its general acceptance. The bridge project case study foundations consisted of HP 14 x 89 pile sections, designed to develop capacity primarily in friction. Preliminary tip elevations were determined by traditional static analyses. Production pile installation was performed using an IHC S-70 Hydro-Hammer. Driving criteria and final production pile tip elevations were determined after preliminary indicator pile drive tests and static load test results at bridge pier cofferdam locations. Based on impact driven production pile performance, the Contractor wished to investigate vibratory driven piles as a means to accelerate construction schedule. Dynamic pile testing procedures were used as the primary measurement tool and test results were compared to the production pile drive records and prior static load tests. Field testing consisted of driving and monitoring with the PDA impact driven piles to the design tip elevation. Three vibratory driven piles were installed to the same tip elevation and immediately subjected to impact driving and dynamic testing to compare dynamic pile resistance. The results indicated that the site soil conditions were favorable for vibratory pile hammer installation. Recommendations and procedures for proceeding with vibratory hammer pile installation were presented to the Owner. These procedures included quality control in conformance with latest AASHTO recommendations. The Owner, in spite of the site specific data base and QA/QC procedures, would not accept vibratory pile hammer installation, due to the absence of precedence. It is concluded that for vibratory methods to become accepted a rational method of analysis, design and field QA/QC procedures requires development. In addition, the engineering community and Owners/Agencies must be more open to alternate methods of foundation construction. The continued development of dynamic methods of monitoring vibratory pile installation is considered to be key to the general acceptance of this installation procedure.

Jan 1, 1991