Search Documents

By Z. D. Tan

The continuous digestion technological conditions of phosphate tailings with high magnesium content in sulfuric and phosphoric mixed acid is studied in this paper. The influences of excess coefficient of sulfuric acid, weight liquid to solid, reaction temperature and time on conversion of P2O5 and MgO are discussed. The influence of infiltration capacity of phosphogypsum by the concentration of liquid-phase SO3 is discussed too. Under the optimal technological conditions, the conversion of P2O5 is 95.56% and MgO 98.63%, the filtration rate of phosphogypsum increases with the increasing of liquid-phase concentration of SO3, the optimal apparent concentration of SO3 is 0.135~0.14g? mL-1 in liquid-phase. The filtration rate of phosphogypsum is 1473kg? m-2? h-1. N-P-Mg compound fertilizer was produced by adding magnesia powder and inflating ammonia in filtering medium.

Jan 1, 2014

By Bulelwa Ndlovu, Saeed Farrokhpay, Dee Bradshaw

The effects of phyllosilicate minerals on the flotation performance and froth stability of a copper ore was investigated. It was found that various phyllosilicate minerals affect the copper recovery differently however they all caused the flotation grade to be reduced. The effect of different phyllosilicate minerals on the froth stability followed the order of talc >> montmorillonite > muscovite > kaolinite > illite. The results demonstrated that there could be a relationship between the deleterious effect of phyllosilicate minerals on the flotation and froth stability. Talc and montmorillonite have both shown the highest effect on the flotation recovery and grade as well as froth stability. On the other hand, illite has the least effect on the both flotation performance and froth stability. Kaolinite and muscovite also affected the copper flotation grade (but not the recovery) while they also affected the froth stability. Therefore it is possible to control the flotation performance when phyllosilicate minerals are present via monitoring and controlling froth stability which needs to be investigated further.

Jan 1, 2014

Gold thiosulfate complex is difference with gold cyanide complex, which is easily adsorbed on activated carbon while gold thiosulfate complex cannot be satisfactorily recovered by activated car-bon. However, Gold thiosulfate could be recovered by activated carbon if cyanide is added into the thiosulfate solution. To avoid the cyanide solution, this paper will review several possible processes to recover the gold from thiosuldate solution: such as the cementation with metals, ion exchange resin and solvent extraction. The gold cementation with the powders of zinc, copper, iron and aluminium will be discussed. The advantage and disadvantage of each are compared. The consumption of thiosulfate and copper and feasibility of solution recycling will be discussed. The gold recovery by some ion exchange resins will be suggested. The processing conditions, its applications and the resin elution methods will be presented. The gold recovery by using solvent ex-traction will be reviewed. The processing conditions of solvent extraction process are discussed and compared.

Jan 1, 2014

"Chairman: Mr. K. F. LaneRapporteur: Mr C. T. ShawPapers:Design of crushing plant flow sheets by simulation by T. GurunThe impact of transportation networks upon the potential supply of base and precious metals from Sonora, Mexico by P. de V. Harris and D. E. EurestyProfitability sensitivity analysis of a mining venture by C. A. Beasley and E. P. PfleiderTechnological innovation and its potential effect on the opening of new gold mines in South Africa by N. C. JoughinMr Turgay Gurun, in presenting his paper, indicated that this simulator was no purely theoretical exercise, but that the model had been used in the design of crushing plants of capacities ranging from 3 000 tons per day to 66 000 tons per day, and that recently the design of a plant of capacity of 99 000 tons per day had been studied.The crushing plant simulator was an independent portion of a much more comprehensive simulator for the design of a. complete recovery plant. It would be possible to use each section of this simulator on its own, and simulators would be designed to cover flotation concentrates, cash flow analyses of the entire project, and so on.Each simulator would be backed by a comprehensive data bank. For example, the crushing plant simulator was backed by such a data bank which included the performance and cost data from five manufacturers for an average of 30 items of process and materials handling equipment each. This meant that data preparation involved generally less work than would be required for a manual calculation. On average, data preparation for one run took 30 minutes and three minutes of computer time on an IBM 360/40 completed the run. The model could be valuable as a design tool in that it allowed the designers an opportunity to make a thorough examination of many alternative designs. It was also of value to plant operators as it could be used to predict the consequences of operating decisions.This paper generated much interest and there were numerous questions and contributions, so many, in fact, that the discussion had to be cut short.It was pointed out by Mr K. F. Lane that crushing plants represented a very large capital investment. A plant designed for 40 000 tons per day at 98 per cent efficiency might well in practice be run at 50 000 tons per day at, say, 83 per cent efficiency. He asked how, therefore, their design could be investigated without building economic criteria into the model? The author conceded that this was a tender point. He would have liked to have given facilities for more variability of the metallurgical information. He pointed out, however, that while there was no overdesign for conservatism built into his system, some overdesign was inevitable as the performance characteristics given by the manufacturers were generally conservative. Also, in his system, if lower recovery was allowed for, the system would nut through more tonnage."

Jan 1, 2014

By D. M. Maijer, S. L. Cockcroft, A. B. Phillion, P. Fan, C. Reilly, H. Khadivinassab

A combined experimental / numerical approach is proposed to investigate the bulk transfer of solute due to liquid metal feeding during shape casting of aluminum alloy A356 (Al-7Si-0.3Mg). A dumbbell-shaped experimental casting geometry has been developed, which promotes solute redistribution due to liquid metal feeding. The redistribution of solute in trial castings is evaluated based on the area fraction of eutectic phases. In the numerical model, silicon species segregation during solidification are calculated assuming the Scheil approximation, and are coupled with macro-scale solute transport due to Darcy flow in the mushy zone and feeding flow. The model has been implemented within the commercial CFD software, FLUENT, which simultaneously solves the thermal, fluid flow fields and species segregation on the macro-scale. The experimental and numerical results are compared and contrasted to examine the effects of liquid metal feeding in this casting.

Jan 1, 2014

By Crasta Jeason, T. Sreenivas, M. Narasimha

The subtle nature of the flow inside the hydrocyclone has encouraged development of mathematical models for predicting its performance, which are widely used in simulation of comminution circuits. But most of the models available are based on single average feed density. But the feed to hydrocyclone classifier is generally mixture of particles of different densities. This effect of varying density of feed particles on performance of hydrocyclone has been reported in literature. Further investigation of the effect of multi component feed on the performance of hydrocyclone is the objective of this work. This work involves experimental work to study multicomponent behaviour in various size cyclones. The performance of hydrocyclone for feed mixture of magnetite and quartz has been studied. The effect of presence of magnetite, a high density material on efficiency of separation of quartz has been analysed. It was observed that the effect of component interaction increases with feed solids concentration leading to an increased cut-size for a given optimum cyclone conditions. Based on the multi-component exiperiments available in literature, a concept for modeling the performance of hydrocyclones is proposed. A set of semi-empirical model equations for cut-size, sharpness of separation are presented. An attempt to validate the new hydrocyclone model on multi-component behaviour is made.

Jan 1, 2014

By Seher Ata

This paper is concerned with the coalescence behaviour of two bubbles in dilute solutions of cetyltrimethylammonium bromide, methyl isobutyl carbonil and triton x-100. Two bubbles were produced at the tips of adjacent capillaries and the time elapsed between the first contact of the bubbles and film rupture was determined by means of a high speed camera. It was found that the amount of surfactant required to stabilise the bubbles increased in order of CTAB>TX-100>MIBC. The probability of coalescence decreased sharply with increasing surfactant concentration in CTAB and TX-100 solutions while with MIBC each bubble pairs resulted in coalescence, giving hundred per-cent coalescence probability.

Jan 1, 2014

By Takahiko Okura, Chiharu Tokoro, Shunta Shibuya

Copper concentrates bearing arsenic as enargite (Cu3AsS4) or tennantite (Cu12As4S13) have disadvantage on copper smelting environmentally and economically, so those concentrates should be treated decently. In this paper, some experiments of arsenic removal from several kinds of copper concentrates by heat treatment in an inert atmosphere were discussed. In this study, several samples in which arsenic contents varied 0.18 to 8.3 wt % were heated to the temperature range of 400 °C to 700 °C under argon gas flow during 1 hour. The heat residues and volatilized materials (V.M.) were analyzed by XRD, XRF, ICP-AES, XAFS and MLA to analyze residual concentration of arsenic and residual mineral composition. Experimental results showed that arsenic removal from copper concentrates advanced in 2 steps; at the temperature range of 500 ° C to 550 °C and of 550 °C to 650 °C, respectively. MLA analysis showed that a few of arsenic in enargite was removed by 550 °C heating and a majority of it was still combined with copper and sulfur as tennantite. On the other hand, arsenic in tennantite was removed almost completely by 650 °C heating. Furthermore, a particular type of arsenic mineral, such as Cobaltite (CoAsS) still remained after heating at 700 °C.

Jan 1, 2014

By Josefin Lannefors, Anders Klingberg, Natalija Gorochovceva

"Development of new anionic collectors becomes more and more important. This can be explained, on the one hand, by the fact that over the years phosphate ores have become more fine grained and complex (example weathered). On the other hand, a development with a focus on sustainability (sustainable development) of new anionic surfactants is required by authorities and society. Within the sustainable development several characteristics of a collector have to be taken into an account: efficiency, selectivity, froth characteristics, environmental profile, raw materials used for the synthesis, manufacturing complexity, stability upon storage, etc.Several anionic surfactants based on ester and amide chemistry were synthesized, characterized and used as flotation agents for calcium phosphate containing ore. The surfactants were used in a formulation together with other anionics, since in a pure form, during the flotation, they did not provide right froth characteristics.A new anionic collector/formulation was developed, that fulfills all above listed requirements."

Jan 1, 2014

By Y. S. Li

The life cycle assessment method is applied to investigate the environmental impacts of cop-per-slag and copper-ore concentration process. Some environmental load data of copper production are obtained. The result indicates that damage level of human health, ecosystem quality and re-sources respectively is 0.174, 0.0203, 0.246 in the copper-slag concentration and 0.112, 0.0136, 0.299 in the copper-ore concentration. Environmental impact of copper-slag production (0.44) is more than that of copper-ore production (0.42), but can meet the environmental protect demand. With domestic copper concentrate supply gap enlarging, recovering copper from slag will lead to a significant improving of resource utilization and development of circulation economics.

Jan 1, 2014

By C. Stollberg

The recovery of valuable materials from electronic waste is of growing importance for the re-source management not only in the industrialized nations. Being a significant step in an innovative automated process for recycling of metals and plastics from used electric and electronic equipment, the results of the work introduced below, prove the applicability of microbial leaching of metals from printed circuit boards (PCBs) at industrial scale. Within the first project step, which started in March 2005, experiments in shaking flasks with a mixed culture of chemolitotrophic bacteria (mainly Acidithiobacillus ferrooxidans and Leptospirillum ferrooxidans) were carried out to study the solubilization of non-ferrous metals present in the electronic waste. It was found that the best results were achieved by means of a two-stage process in which leaching of these metals was carried out by acidified ferric sulphate solutions generated as a result of the prior bacterial oxidation of ferrous ions to the ferric state. Special reactor systems for bacterial generation of such solutions and for the subsequent leaching of non-ferrous metals from the waste were developed, constructed and tested under laboratory and pilot scale conditions. The optimum technological parameters such as concentration of iron ions, pH-value, temperature and presence of nutrients were established for both reactor systems. Parameters such as particle size, pulp density and flow rate of the suspensions being leached were established for the leaching process carried out under continuous-flow conditions. The complex flow sheet reflects a highly efficient technology on the basis of metal recovery, environmental effect and economical acceptance. The process was successfully implemented into an industrial demonstration unit.

Jan 1, 2014

By A. S. Macfarlane

This paper describes how knowledge of the orebody morphology and ore morphology can be used to optimize the planning, mining, and metallurgical output from an open pit copper mining operation, such as to significantly increase the stability of the whole value chain process, and increase the reliability and value of the process outputs. In the case under consideration, the orebody contains both copper and cobalt. This in itself provides a challenge, in that the two metals do not occur in consistent ratios across the orebody as a whole. Furthermore, mineralogical differences within the orebody have a significant impact on plant performance in terms of throughput rates, acid consumption, and recoveries. In order to stabilize and optimize the plant performance, it is necessary to firstly have a complete understanding of the geometallurgical factors that affect performance, and then to have a sound knowledge of how these are distributed within the orebody. These models then inform the mine planning strategy that optimizes cash flow and NPV, and also allow the development of a stockpiling strategy that not only stabilizes the plant, but also allows variations in the plant feed according to ore type and grade in volatile price scenarios. Integral to the realization of these opportunities is the establishment of an appropriate measuring, control, and reconciliation system, customized to the optimization objectives. The paper describes how all of these factors and strategies can be integrated to produce optimal value from the orebody through to final dispatched product. It also shows the significant value that can be released through such an approach.

Jan 1, 2014

By Steve Kral

"The Rapid Excavation & Tunneling Conference (RETC) is a world-renowned event that attracts some of the best minds in the global underground construction and tunneling industry. The experts gather at this conference to impart new technologies, discuss challenges to their projects and learn about new technologies that have become available to them.The 2015 RETC will be held June 7-10 at the Sheraton New Orleans, in New Orleans, LA. This biennial conference, of which SME is a sponsor, is expected to attract about 1,400 attendees from around the world. These professionals represent all parts of the global tunneling and underground construction industries - contractors, engineers, owners, consultants and equipment suppliers.More than 110 technical papers in 21 sessions will be presented over two-and-a-half days. Paid attendees will receive a proceedings volume of the conference. The proceedings will also be available from SME. In addition to the technical programming, the accompanying exhibit will include 155 exhibitors occupying 175 booths, providing RETC attendees the opportunity to get a look at the latest in equipment and service technology. Three short courses will be held on the Sunday preceding the start of the show. And there will be plenty of opportunities for attendees to meet and chat during several social activities that are scheduled throughout the conference."

Jan 1, 2014

By Luis Bergh, Francisco Díaz, Isabel Panire, Juan Yianatos, Luis Vinnett

"In this paper, industrial data of residence time distribution (RTD) in mechanical flotation cells is presented, which were measured in several plants using the radioactive tracer technique. Results include mechanical flotation cells of 100 - 300 m3, which were operated with effective residence times from 2 to 7 min. Tests were developed in forced air and self-aerated cells for liquid and solids (non-floatable) per size classes. Different RTD model structures including perfect mixer, Large and Small Tanks in Series (LSTS) and by-pass flow plus perfect mixer were evaluated and compared for single cells. The actual mixing regime was related to the effective residence times and cell designs based on the model fitting. By-pass flow percentages were typically lower than 10%, therefore the perfect mixer model plus a dead time was a suitable model structure in most cases. On the other hand, the arrangement of cells in series was effective in reducing the bypass flow observed in single cells (by-pass flow percentage greater than 5%). In addition, the N perfectly mixed reactor in series model was used to represent the mixing regime along flotation banks, which were operated with mean residence times in the range of 18 - 53 min. Results showed that N tanks in series plus dead time were closer to the actual values in most cases."

Jan 1, 2014

By Mahdi Shevrini, Hamed Haghi

"In this research, the operation of screen classifying in silica processing circuits was investigated and modified by replacement of available trommel screens with teetered bed separator (TBS). In addition the effect of the mentioned replacement and addition of attrition scrubber on quality of final product, impurities removal, recovery and production rate were inspected. Considering screen efficiency problems to achieve certain particle size distribution, hydraulic classifying system was selected instead of trommel screens. Application of suggested plan improved quality and particle size distribution of produced silica significantly. Optimization of size classification in process circuit resulted in increase in production rate up to 21% (from 67% to 81%), silica recovery (from 68.35% up to 83.11%) and relative enhancement in removal of impurities such as Fe2O3 and TiO2. After optimization and stabilization of grinding and size classification section, industrial attrition scrubbing tests were carried out and the best solid percent and retention time were determined i.e. 70% and 6 minutes, respectively. Using sodium carbonate during attrition scrubbing, has major effect on removal of surface coating and staining especially sharp increase in clay removal; therefore 2 kg/t of sodium carbonate can be optimistic point of industrial procedure for this silica processing plant. It should be mentioned that application of attrition scrubbing which is followed by screw classifier for de-sliming were useful for better cumulating of particles in the range of appropriate liberation degree (+106-300µm) and efficient removal of metallic (iron and titanium oxides) and non-metallic (clays and feldspars) impurities."

Jan 1, 2014

By D. R. Nagaraj, Raymond Farinato

Water constitutes one of the most valuable resources employed in mineral recovery and processing. Identifying potential problems encountered in mineral processing in waters unusable for drinking or agriculture (including seawater and even hypersaline waters), understanding chemical factor interactions, and optimization of flotation reagents will greatly expand our ability to create more sustainable beneficiation technologies. The current paucity of our knowledgebase regarding high salinity effects on flotation clearly signals a need for a significant research effort. We report here results of a study designed to probe effects of pulp chemistry on metallurgical performance in the flotation of Cu and Cu-Mo ores in saline waters. The results clearly demonstrate that pH (more correctly dosage of pH modifier to target a pH set point) has the most significant effect on Mo recovery when using seawater. This is linked to the formation/precipitation of Mg(OH)2 when pH = 10.3 (in seawater). The type of pH modifier used, NaOH or Ca(OH)2, had no impact on Cu or Mo recovery, indicating that Ca2+ ions were not involved in any reduction in Mo recovery in the pH range of 9-11. Our results in tap water spiked with either Ca2+ or Mg2+ ions in the same pH range (controlled by NaOH), confirmed that Ca2+ ions had no effect on Cu or Mo recovery, but that addition of Mg2+ ions had a severe adverse effect on Mo recovery at pH = 9.5, and to a lesser extent on Cu recovery. The onset of Mg(OH)2 precipitation occurred at a higher pH, and the adverse impact of Mg(OH)2 on Cu recovery (and perhaps Mo recovery as well) was less, in sea water than in tap water spiked with Mg2+. These effects are attributed to the mitigating role of the high electrolyte concentration, notably NaCl.

Jan 1, 2014

By K. Saberyan

In this study the extraction of zirconium and hafnium has been investigated by solvent extraction using Cyanex 302 in various media such as nitric, sulfuric and hydrochloric acid has been investigated. Effect of various parameters such as type and acid concentration, extractant concentration, type of diluent, equilibrium time, various foreign ions and finally type and concentration of strip-ping agent have been studied. The results showed that nitric acid was optimum media for extraction of zirconium and hafnium. The extraction of zirconium and hafnium occurred quantitatively in the concentration of higher than 4 M nitric acid but in hydrochloric acid media, quantitative extraction obtains over 8 M HCl. In sulfuric acid media, extraction of zirconium and hafnium is negligible. Stripping studies showed that the optimum reagent for stripping was 0.5M sulfuric acid.

Jan 1, 2014

By A. Wieniewski

The observed progress in technology of non-ferrous ores enrichment and condition of machines and equipment in the ores concentrators on the one hand have brought a possibility and on the other resulted in necessity for introduction of modernization actions. Positive results of investigations into influence of chemical modification of selected products of enrichment process on copper ores enrichment results gave possibility for implementation of chemical-flotation technologies of ores enrichment. The substantial development in flotation machines structure has contributed to modernization of flotation process resulting in increase of enrichment efficiency. The paper presents the idea and results of chemical modification of difficult in enrichment semi-products in the technology of copper ores enrichment and the results obtained after application of the modernised technology. The structure of large-volume flotation machines used in various stages of flotation and current situation in modernization of flotation process in copper ores concentrators are also described. The paper presents industrial-scale results of flotation after application of modified flotation reagents of collector group. Introduction of modifiers into the widely used xanthates resulted in increase of copper recovery in concentrate.

Jan 1, 2014

A localized nonlinear recoverable resource estimate technique has been applied using typical feasibility or new mining drilling data configurations drawn from a massive database from a mined-out area on a hydrothermal gold deposit. The results were then compared with the corresponding 8 m x 5 m grid grade-control data in order to determine the efficiency of the approach and the validity of the recoverable resource estimates for mine planning and financial forecasts.

Jan 1, 2014

By V. Yahorava

Ion exchange is considered to be an effective technology for the removal of various impurities from cobalt advance electrolytes. With the correct choice of resin, ion exchange can consistently remove the required impurities to the levels for the production of high-grade cobalt metal. Although ion exchange was in the past used primarily for nickel removal, more recently it has been also considered for the removal of copper, zinc, and cadmium. Generally, granular ion exchange products are used, but Mintek is currently evaluating ion exchange fibres for a number of applications, including the removal of copper from cobalt advance electrolytes. Fibrous ion exchangers have major advantages compared to granular resins in that they have significantly higher reaction rates, and wash water volumes could be limited. Granular and fibrous ion exchangers were evaluated and compared for the removal of copper from cobalt advance electrolyte. A synthetic electrolyte containing 50 g/L cobalt and 50 mg/L copper was used for the test work. Equilibrium isotherms, mini-column tests, and split elution tests were done. The results were used to size a full-scale operation to treat 100 m3/h of electrolyte. The potential cobalt losses or recycle requirements were estimated, and data to calculate indicative operating costs for each adsorbent was generated. This information was used for a techno-economic comparison of granular and fibrous ion exchange systems for the removal of copper from cobalt advance electrolyte.

Jan 1, 2014