Search Documents

By Roderic A. Ellman

The new Woodrow Wilson Bridge (WWB) will replace the existing bridge over the Potomac River to connect Alexandria, Virginia to Prince Georges County, Maryland. The new WWB will extend approximately 1.1 miles across the river, with a 367-ft long bascule span in the main river channel where the water depth is about 36 ft. The subsurface soil profile consists of up to 50 ft of a soft organic silty clay layer that is very vulnerable to scour, underlain by a deep deposit of hard sandy clay. Foundation construction in the Potomac River required the use of cofferdams to allow structural concrete work to be performed in the dry. This paper will the present the types of cofferdams used to construct the foundations for the WWB replacement project. The bridge is primarily comprised of fixed spans in relatively shallow water and a bascule span over a navigation channel in relatively deep water. Foundation construction included the installation of 48? to 72? open end steel pipe piles and cast-in-place concrete pile caps. To achieve the desired bridge appearance, pile caps were required to extend below the water surface and below the existing river bottom in shallow water locations. Conventional steel sheet pile cofferdams with tremie concrete seal were used to construct fixed span, shallow water piers. Selection of deep water bascule span foundation cofferdams was governed by several factors including contraction scour, environmental considerations and cost. Potomac River cofferdams, i.e., relatively shallow depth cofferdams that are supported by the foundation piling were selected. This cofferdam system provided a shallow profile which minimized contraction scour and the amount of filling in the river. Design issues include load selection and cofferdam stability in very soft alluvial soils. Construction issues include erection sequence, tremie concrete mix design and placement procedures.

Jan 1, 2013

By Ben Fahrman

The classical approach to engineering design involves the purely deterministic calculation of the factor of safety, the ratio of strength to stress. The factor of safety is an easy calculation to perform in many circumstances, and it is very easy to interpret the results. The simplicity of the method is both a strength and a weakness. The results of the deterministic factor of safety calculation are simple to determine and interpret, but they have no ability to account for the uncertainty present in the inputs or outputs. Uncertainty is prevalent in geotechnical engineering applications. This uncertainty can stem from spatial variability, poor sampling, a dynamically changing environment, etc. Probability analyses allow input parameters to take the form of a distribution rather than a single value, making them uniquely equipped to handle the uncertainty inherent in geotechnical engineering design considerations. A stochastic approach also has the benefit of providing results as a probability of failure, which is more meaningful than a factor of safety. Though stochastic modeling is becoming more common in many geotechnical applications, it is still not widely used for coal pillar design. The objectives of this study are to justify the concept of using a stochastic approach to coal pillar design and to compare the results of a simple stochastic analysis to those of standard industry practice. A simple synthetic study was performed to compare the results of a probabilistic analysis of coal pillar design to the results obtained from running ARMPS, which is published by NIOSH. Normal distributions were assigned to each input parameter that is required to determine the factor of safety of a single coal pillar. The probability of failure resulting from the synthetic study was found to be more conservative than the ARMPS stability factor. A probabilistic approach to coal pillar design is discussed in comparison to the traditional deterministic approach. The greatest strengths of the probabilistic approach were determined to be the effective handling of uncertainty and the increased meaning of the inputs and outputs inherent to a probabilistic approach.

Jan 1, 2013

By Stephen E. Kesler

Carbonaceous sedimentary rocks are abundant in the upper part of the caldera or maar that hosts the Puebio Viejo Au-Ag district, and much of the Moore sulfide zone is in these rocks. These rocks are thinly layered and contain scattered plant remains and variable amounts of volcaniclastic debris and pyrite. The carbonaceous matter in the sediments yields no X-ray diffraction pattern and is not graphite. It has C/N ratios of 4 to 10, and &13C values of about -25 per mil, which indicate that it is dominantly of marine organic origin and partly degraded. Atomic S/C ratios in the unmineralized part of the carbonaceous rocks have a median of about 1.2, much higher than most similar unmineralized rocks, reflecting not only the abundance of pyrite in the sediments, but also the fact that the organic material contains several percent sulfur. Extracts from the organic material indicate that it is thermally mature and that it reacted with the hydrothermal solutions. Atomic S/C ratios in the mineralized carbonaceous rocks are generally higher than those in unmineralized carbonaceous rocks, ranging to values of 5 and more. These differences indicate that significant amounts of carbon were consumed by the reduction of sulfate and metal chloride complexes in the mineralizing fluids as they passed through the carbonaceous sediments. Direct reaction between organic material and ferrous chloride-bearing, acid-sulfate hydrothermal solutions probably caused continuous deposition of pyrite during this period. Intermittent deposition of gold from chloride complexes by the same reaction was probably facilitated by boiling or C02 effervescence.

Jan 1, 2013

By Jan Pan, Deqing Zhu, Xianlin Zhou, Yanhong Luo, Zixing Xue

"Magnetic roasting process, aiming at obtaining magnetite concentrate, is the principle method of exploiting siderite as a raw material in iron and steel industry. Study on preparing DRI from siderite through coal based reduction technology is sporadic. To make the process of how siderite is reduced to iron clear, roasted ore reduced from siderite by lignite under different time periods were analyzed. The results indicated that: at the temperature of 1050°C, siderite was rapidly decomposed into magnetite, and further reduced as Fe30r?FeO?Fe, the later step was slower than the previous one. A fracture of particles was found during the process of thermal decomposition and the reduction of newly formed magnetite. As the reduction proceeded, metallization rate of products increased, and the iron grain grew along with time.IntroductionWith the rapid development of economy, China demands more and more iron ores for the iron and steel industry. China has rich iron ore resources, but 97% of them are below 30% in iron grade, many are refractory and unutilized [1], therefore large quantities of imported iron ores are in a desperate need. China imported 686 million tons of iron ore in 2011 (data from the China Customs), accounting for nearly 60% of the total consumption. To guarantee the healthy development of iron and steel industry, domestic refractory iron ores have to be utilized both economically and environmentally."

Jan 1, 2013

By P. R. Mothemela

The objective of the investigation is to optimize the truck and shovel operations for pre-stripping at New Vaal Colliery by introducing campaign mining. The aim of campaign mining is to improve the efficiency of the loading, hauling, dumping, and maintenance operations which are critical to the success of truck and shovel operations. The current loading (single-sided loading method), hauling, and dumping operations at New Vaal Colliery were found to be inefficient. Time studies were used as a major indicator to highlight the inefficiency of the truck and shovel operations, and it is recommended that an improved loading configuration, hauling, and dumping operations be implemented by using campaign mining. It is also recommended that a service truck be used to maintain the pre-stripping fleet in order to reduce travelling times to the main workshop. As expected, the improved operating conditions will lead to an increase in pre-stripping production.

Jan 1, 2013

The National Mining Hall of Fame and Museum (NMHF&M) will celebrate its 25th anniversary on Sept. 22, 2012 when the 2012 class is inducted during a special ceremony in Las Vegas, NV in conjunction with MINExpo 2012. The NMHF&M will induct four men representing the equipment manufacturing, minerals exploration, copper and coal sectors of the mining industry. The diverse cross-section of mining industry giants joining the hall of fame include Glen A. Barton, J. David Lowell, Samuel Newhouse and John Cleveland Osgood. They will join 214 other mining industry pioneers when they are formally inducted into the National Mining Hall of Fame at the 25th Silver Anniversary Induction Banquet & Ceremony. These men were selected for being visionaries, leaders and ambassadors within their own sectors and across the industry at large.

Jan 1, 2013

What is your personal view and assessment of the overall health of the industry in the current global economy? The economic outlook remains soft for the near future and, although the global economy is showing signs of recovery, uncertainty has tempered the pace of recovery. In addition to uncertainty, we are still facing significant economic challenges in many parts of the world, including Europe and the United States. The rapid expansion of China?s economy has recently slowed, further contributing to the sense of uncertainty in the overall health of the global economy. This situation is both a blessing and a curse, depending on which sector of the mining industry we are considering. For example, coal, industrial minerals, aggregates, base metal and precious metals markets are impacted by different forces and drivers and will experience different outcomes within the same economic environment. Let me give a few concrete examples to illustrate this concept. The prevailing economic uncertainty that I have just described tends to drive investors toward safe havens. Gold has historically been viewed as a safe haven and as long as investors shy away from traditional investments, gold prices will remain high and gold mining companies will continue to expand and invest capital in their operations. The same sluggish economy that drives gold prices higher has the opposite effect on other segments of the minerals industry. A great example of this is industrial minerals and aggregates used in construction. The markets that consume these minerals have contracted significantly over the past five years. The outlook for this segment is poor, as the glut of available housing continues to inhibit demand for new construction and, thus, many industrial minerals. In addition to this, the federal government?s lack of political will to enact long-term legislation funding transportation and infrastructure projects continues to be a drag on the U.S. aggregates industry.

Jan 1, 2013

By F. T. Cawood

Despite economic law and policy instruments with righteous intentions, the politics of resource nationalism could render these instruments unworkable. South Africa is a case in point. After the establishment of democracy, the country's outdated law and policy framework was replaced with a modern system, and in many respects an exemplary one. Converting the privately-owned mineral right system into a scheme of state custodianship allowed for several resource nationalism instruments, in addition to a resources royalty structure that first, compensates for the loss of a non-renewable resource; second, provides for optimal resource use through encouraging value addition to mineral production; and third, effectively targets economic rents. However, despite these improvements, the country went through a process of fierce debate on whether or not mines should be nationalized: the debate was fuelled by public anger with claims of political non-delivery. The result was considerable noise because of public unawareness of facts and distortion of the facts in political rhetoric. The purpose of this article is, first, to establish the status of resource nationalism in South Africa's mineral and fiscal frameworks; second, to give an opinion on the findings of the African National Congress's document on state intervention (Maximising the Developmental Impact of the People's Mineral Assets: State Intervention in the Minerals Sector (SIMS), 2012); and third, to fruitfully contribute to the fundamental discussion on how South Africans benefit from their mineral riches. The methodology is to start with explaining resource nationalism as an international issue for the extractive industries; then to offer an overview of existing resource nationalism instruments in South Africa-along with their effectiveness in attracting rents and investment. The major finding is that South Africa has resource nationalism firmly ingrained in its current suite of instruments. However, it is necessary to address the perceptions of bad governance, and above all, maintain the stability of the rules governing mineral development in South Africa.

Jan 1, 2013

By James S. Graham

Marine design and construction methods are presented on the caisson foundations for the tower piers at the Brooklyn, Ben Franklin, Delaware Memorial 1st, Tappan Zee, Walt Whitman, Throgs Neck, Verrazano Narrows, Delaware Memorial 2nd, and Newport Bridges. All of the bridges are founded on caissons, bearing on bedrock, soil, or piling. Caissons at the Tappan Zee Bridge are partially supported by piling and partially by buoyant forces. General subsurface conditions for each are provided. The purpose of this paper is inform engineers how bridge foundations using caissons were built over major waterways in the Northeastern USA in the past, anticipating a surge of new bridge construction in the near future.

Jan 1, 2013

By Guanghua Wen, Jian Li, Mingmei Zhu, Fei Xiong, Shengjian Cao

"Small inclusions removal from molten steel in a continuous casting tundish by gas bubbles, which were generated in the turbulent flow region by introducing inert gas, was analyzed theoretically and the inclusion-bubble adhesion and flotation process was also observed by high-speed photo-graph in water model. Results showed that small inclusions in the range of 20-50µm removal from molten steel by bubbles flotation involves three stages: contact, adhesion and flotation. The inclusion-bubble adhesion processes include two ways: inclusions adhering to the upper part of the bubble and inclusions adhering to the lower part of the bubble. As the bubble floats up, the number of inclusions adhering to the bubble are increased. The proper size of bubbles, which could enhance small inclusions removal efficiency, should be controlled in the range of 1-2mm.IntroductionReducing inclusions content in molten steel is a very important way to improve quality of steel, and one of the main tasks in steel making process.A variety of methods have been used for inclusions removal in molten steel. At present, the main approaches to remove inclusions are gas stirring, slag cleaning, filtering, centrifugal separating, and by means of ultrasonic or electromagnetic field. Among these techniques, gas stirring is the most widely and effectively method for inclusions removal. Inclusions in molten steel will be aggregated and generated to form larger size inclusions, and subsequently floated to the surface of molten steel by buoyancy; meanwhile, some inclusions will be adhered to bubbles and floated together to metal-slag interface where inclusions are absorbed by the covering slag layer. Some research work showed that flow behaviors of small bubbles are different from that of big ones [1-2], and smaller bubbles are more efficiency for fine inclusions removal in molten steel.There are many methods to generate bubbles. During steelmaking process, highly turbulent flow in the ladle shroud can split introduced inert gas into small bubbles, which enhances the removal of fine inclusions from molten steel. Turbulent flow of molten steel injected into tundish from ladle shroud has a high speed and it is a strong turbulent area in continuous casting. The gas can be introduced into the shroud below the slide gate. The high turbulence flow would break up the gas into small gas bubbles. Fine inclusions will be easily adhered to small bubbles and subsequently floated to the surface of molten steel. Generation of small bubbles in ladle shroud have been studied in some literatures [3-4]. Some research have analyzed the fine inclusions removal with injecting gas from the ladle shroud by mathematical simulation, and the results show that the refining method can obviously improve the removal efficiency of fine inclusions in tundish [5-8]."

Jan 1, 2013

By Andrew Campbell, Michael Reed

"WorleyParsons has used Discrete Event Simulation methods in conjunction with more traditional process models to assess the performance of copper smelting operations. This work was performed to determine the plant capacities and suitability of proposed debottlenecking options including accounting for the planned and unplanned (breakdowns) shutdowns in the various parts of the plant and supply chain. This paper outlines the methods used along with demonstrating the benefits of selecting a feasible option and minimizing capital and operating costs.IntroductionTraditionally for de bottlenecking studies of smelters and other process plants, a mass balance is performed based on continuous operating rates and expected operating hours. Smelters have several points of failure that will restrict, if not take the entire plant offline. By using a more detailed model, validated against plant experience, bottlenecks can be demonstrated and strategies to remove them to increase plant availability and economic.The modeling simulates the plant performance in real time, and by performing enough simulation the expected long run performance of the plant can be estimated. The models have been built using ExtendSim which is a powerful Discrete Event Simulation software package that is ideally suited to the batch and semi-batch processes and events that occur within smelter operating environments. The value of performing this work is that the operational performance of the plant can be assessed ensuring production targets are met, without using excessive capital outlay."

Jan 1, 2013

By G. Mitchell

Much debate has ensued over the past few years on the speed of transformation in the mining industry. By transformation is meant the degree to which the industry has met the requirements of the Mining Charter. In response to this, the Department of Mineral Resources (DMR) commissioned a research study in 2009 to ascertain the degree of industry compliance. The mining industry in response made a presentation to the Minerals Portfolio Committee in Parliament in 2011, during which it released aggregated figures on industry compliance to the Mining Charter. The conclusions of both of the studies are widely divergent. It is argued in this paper that both processes are flawed. The government-sponsored research is empirically and methodologically weak and the results therefore have to be taken with a great degree of caution. The Chamber of Mines figures, on the other hand, while faithful to the reporting of the Chamber member companies, do not represent the entire span of the industry but only the larger mining companies. It is further argued that in order to ascertain a true reflection of the industry an independent audit be undertaken using recognized social scientific survey methods.

Jan 1, 2013

By Claude Bazin, François Robichaud

"The control of the operation of semi autogeneous grinding (SAG) mills is mainly achieved through adjustments of feed rate, water addition and speed of rotation. With the introduction of image based sensors it is possible to have on-line measurements of the size distribution of the ore feeding a SAG mill. This information could be used for the development of a control strategy to regulate a SAG mill feed size distribution to a set-point. The control of the size distribution is carried out by adjustment of the speed of the ore extractors underneath the ore stockpile. The potential and difficulty associated with the implementation of such control are assessed using a multivariable statistical analysis of data collected from the operation of the grinding circuit of the Agnico-Eagle Goldex mine in Val d’Or, QC. A control strategy for the ore feed size distribution is assessed using a simulator of the ore stockpile operation.INTRODUCTIONThe popularity of autogeneous (FAG) and semi autogeneous (SAG) grinding mills has been increasing over the last 20 years (Napier Munn et al., 1996). These mills use the ore or a combination of ore and steel balls as the grinding media. Since the ore is used as a media for the size reduction the mill ore feed size distribution impacts the performance of the mill. Several papers were recently published on this subject (Dance et al.,2011; Wennen & Murr, 2011; Dance & Valery, 2011; Allaire et al., 2011) showing the advantages of preparing the feed size distribution to maximize the circuit throughput or mill efficiency (Wennen & Murr, 2011; Dance & Valery, 2011; Allaire et al., 2011). With the availability of particle size sensor based on image analysis of the ore on a conveyor (Partanen et al., 2001; Bobo et al. 2004; Edwards et al., 2002; Wei & Craig, 2009) it is possible to control the size distribution of the ore feeding autogeneous or semi autogeneous mills (Partanen et al., 2001).This paper describes a method to control a size distribution index to a set point via the manipulation of the speed of the extractors that withdraw the ore from the stockpile feeding the grinding circuit. The paper consists of 4 sections. The first section describes the considered grinding circuit. A statistical analysis of the collected data on the grinding circuit is presented in the second section. This analysis demonstrates the necessity of using real-time adaptation mechanisms to develop a control strategy for the size distribution of a grinding circuit. The third section describes the method used to simulate the ore stockpile operation and the last section describes the preliminary development and assessment of a control strategy of size distribution of the ore feeding a SAG mill."

Jan 1, 2013

By Xiao-hui Fan, Li-shun Yuan, Xu-ling Chen, Wei Lv, Min Gan, Yi Wang

"As the amount of ferrous scrap increases every year, it becomes more and more urgent to deal with this iron-bearing resource properly. This paper puts forward a method on resource-oriented utilization of ferrous scrap (cold-bonded pelletizing), and these cold-bonded pellets can be used as coolant in a converter. The influence on the pellets qualities by using different kinds of chloride as rust agents is studied, and results show that the strength of cold-bonded pellets increases significantly by using a combination of the three kinds of chloride -NaCl,MgClz,FeCh, their best dosages are 1.2%, 0.2%, 0.1% respectively. Other iron-bearing materials also have an effect upon the pellets strength, by adding 5% iron powder and maintaining for 48h, the compressive strength of the clumps surpass 2500N/A, dropping strength surpass 4 times/ A, and 10% iron slag or 20% steel slag can replace 5% iron powder while obtaining the comparative quality. The influence of different ratios of three ferrous scrap (converter mud, iron scale and dust) is further studied, and results show that when the ratio is 30% : 30% : 40%, the pellet strength reaches the maximum. After maintaining for 24~48h, the clumps can meet the mechanical as well as the physical-chemical requirements as BOF steelmaking refrigerant.IntroductionGreat amounts of converter mud, dust and iron scale are produced in steel production process. These materials are of great values, and their accumulation not only leads to environmental pollution, but also wastes the precious resources, which restricts the sustainable development of the steel industry [1,2] The main approach at present to dealing with the ferrous scrap is to add them into sintering. But in this way, the utilization factor of sintering and the quality of sinter decline while the energy consumption increases [3].Therefore, more advanced and efficient technology is needed to make the best of these iron resources. Cold consolidation of ferrous scrap is a simple process that has many advantages such as less investment, quicker effect, lower energy and lower cost [4-5] But the conventional maintaining period is too long, usually up to four-six weeks, and the pellet strength is low. Therefore, the key points of the cold-bonded pelletizing are to develop a new adhesive [4,5] to shorten the natural maintenance cycle and to improve the strength of the pellets. A method on resource-oriented utilization of ferrous scrap (cold-bonded pelletizing) is brought forward, and these cold-bonded pellets can be used as coolant in converter. After maintaining for 48h, these cold-bonded pellets can satisfy the mechanical requirements to replace the converter coolant [6]."

Jan 1, 2013

By W. L. Saunders, Richard T. Dana

The dynamites are graded according to the percentage of nitroglycerin that they contain. Thus a “40% powder” would be one in which the sticks, weighing one-half pound each, would include one-fifth of a pound of pure nitroglycerin. Dynamite is usually packed in paper cartridges weighing about one-half pound each which will vary in diameter. When ordering, it is customary to specify a size of cartridge that will as nearly as possible fill the drill hole, the commonest size being 1 ¼” in diameter by 8” in length. It is nearly always shipped in 50-lb. boxes, which have a volumetric capacity of 3/4 cu.ft.

Jan 1, 2013

By M. G. Maruma

The effect of the amount of cold reduction and annealing temperature on the evolution of the texture of AISI 441 steel is reported. The steel was cold rolled by 62%, 78%, and 82%, followed by isothermal annealing of each sample at 900°C, 950°C, and 1025°C for 3 minutes. The crystallographic texture was determined by Phillips X?Pert PROMPD texture diffractrometer. Microstructures were characterized using optical microscopy and scanning electron microscopy (SEM).The results show that sample that received 78% cold reduction and annealing at 1025°C presented the highest Rm-value and lowest ?R-value, which would enhance its deep-drawing capability. In addition, this sample showed the highest intensity of shifted ?-fibre, notably {554}<225> and {334}<483>. It can therefore be concluded that the ?-fibre, which favours deep drawing, is optimal after 78% cold reduction and annealing at 1025°C.

Jan 1, 2013

By S. C. Gaillard

Tailings are made of ground rock that is left over from removing valuable minerals. The tailings are usually fine particles that cause environmental issues for storage and disposal. Disposal of tailings is a growing concern, as more tailings are produced from the increasing demand for mined material (ITRC, 2008). This project proposes a way to convert the mine waste to a useful product. Tailings were selected from a South Carolina crushed stone quarry, the products of which are used for road beds, sidewalks, asphalt and driveways. These tailings were processed to generate synthetic aggregates for construction applications. The synthetic aggregate creates a product that could be used for many purposes, including aggregate for sidewalks, driveways, roads and building materials. Testing methods followed the North Carolina Department of Transportation (NCDOT) guidelines for physical testing of coarse natural aggregate, which are sieve analysis, Los Angeles abrasion, absorption, specific gravity and soundness test. The synthetic aggregate produced passed all tests for NCDOT and, in some instances, rated better than a natural aggregate. Using the tailings from the crushed stone and mining industry would convert the waste into a valuable, marketable product.

Jan 1, 2013

By James D. Pile

Following a methane ignition in the active panel of a longwall coal mine, the affected panel was successfully isolated from the rest of the mine. This allowed for the remainder of the mine to return to regular operation, and the conventional practice of having to seal the portals for a defined period of time was avoided. After the affected panel had remained isolated for a regulatorily mandated period of time, it was reopened in preparation for longwall face recovery. As it was not possible to move the shields from their existing positions to facilitate the installation of recovery mesh prior to shield recovery, alternative methods had to be considered to stabilise the gob and minimise flushing, thereby improving operator safety. The objective of the paper is to show how stabilisation of the gob was achieved during shield recovery, thereby minimising flushing, and improving operator safety. Phenolic foam was chosen and injected from between the shields into the gob behind them. This is a technique that has been used to great effect in Germany, to a lesser extent in Australia, but not knowingly to date in the United States. To ensure nothing was left to chance and thereby guarantee the project?s success, the procedure used in Germany was employed, down to the application of equivalent hardware, which was sourced through the North American supplier.

Jan 1, 2013

By Ryan Garvey

A numerical investigation is made into unstable failures of coal pillars (i.e. coal bumps) using the finite difference software FLAC3D. A static energy balance is first derived to calculate the excess energy released as a consequence of unstable failure in rock. Two- and three-dimensional mining layouts are then assessed on their bump-potential based on the magnitudes of excess energy released during simulated pillar failures. A three dimensional pillar model is developed to represent tributary area loading of an infinite room-and-pillar layout. Pillar strength and brittleness characteristics are calibrated using a Mohr-Coulomb strain-softening constitutive law to simulate width-to-height ratio coal pillars ranging from 1:1 to 5:1. Width-to-height ratio pillars 1:1 to 3:1 release large magnitudes of excess energy as the pillars fail, representing massive collapse of room-and-pillar layouts. The larger pillars maintain their residual strength during failure; however significant excess energy is still released during temporary reductions in pillar strength. A two-dimensional model is then constructed of a gate road pillar failing due to elastic rebound of the surrounding rock mass. Soft loading conditions initiate unstable failure for all pillar widths, while the total magnitudes of excess energy increase with the size of pillar being modeled. The results from these tests indicate that excess energy may be used as a direct assessment of the bump potential of simulated mine layouts.

Jan 1, 2013

By Gordon J. Hughes

The ldaho Cobalt Belt represents a unique geologic environment containing some of the largest known reserves of cobalt in the United States. Stratabound cobalt-copper-gold deposits formed within a sedimentary basin that was generated by the rifting of an Archean cratonic block. Host rocks for these deposits are the Early to Middle Proterozoic Yellowjacket Formation comprising a suite of clastic sediments, volcaniclastics, and mafic tuffs that accumulated in the intracratonic rift basin about 1.7 b.y. ago. Rifting was probably initiated during a regional heating and doming event that may date back to 1.8 b.y. ago. During this time, other rift basins were likely to have formed in the region. They probably represent the precursors of a much larger depositional environment having characteristics of an Atlantic- type or passive continental margin where younger formations of the Belt Supergroup were deposited. The Yellowjacket Formation has been subdivided in the Idaho Cobalt Belt into three genetic units representing various subenvironments of a deepwater clastic fan complex. A northwest- trending deep-basin structural trough accumulated fine-grained muddy sediments that were periodically interrupted by distal turbidites of the subaqueous fans. Subsequent progradation caused the deposition of coarser-grained clastics of the more proximal portions of the fan complexes. Submarine fan lobes were built across northwest-trending tectonically active basin growth faults. These in-basin structures caused a great deal of penecontemporaneous deformation within the Yellowjacket sequence. Northeast-trending fault zones formed an orthogonal set of fractures that controlled the shape and size of sub-basins, and were also an influence on lateral migration of dominantly fine-grained clastic material. The eruption of mafic tuffs at about 1.7 b.y. ago added a new component to the Yellowjacket sedimentary sequence. Around the Blackbird mine area these tuffs commonly occur either near the base or within some of the sandier sequences. Since most of the sand influxes were largely controlled by basinal tectonism, the tuffs were probably erupted during tectonically active periods of basin development. The dynamic nature of the sedimentary environment probably caused much of the tuffaceous component to be mixed with other clastics and even resedimented as volcaniclastic material. In time, the change to a higher energy sedimentation regime resulted in such a dramatic clastic dilution of the tuffs that they could not survive in the areas of the vents, and, if present, they must have been distributed elsewhere in the basin.

Jan 1, 2013