Search Documents

By Tae-Hyun Kim, Shun Myung Shin, Jin-gu Kang, Jeong-Soo Sohn

We investigated about synthesis of Mn-Zn ferrite with spinel structure using sulfuric acid leaching solution of mixed spent zinc-carbon batteries and spent alkaline batteries. The waste batteries were prepared by physical treatment such as crushing, magnetic separation, and screening. After screening, the crushed batteries were separated to +8 mesh and -8 mesh powder. Among these, under 8 mesh powder was selected for leaching test. The leaching test was investigated at 2 M H2SO4, 4 vol.% H2O2, reaction temperature 60 ?, agitation speed 250 rpm, solid/liquid ratio 50 g/ 500 ml, reaction time 1 h. The leaching efficiency of zinc, manganese and iron were 99.0%, 98.9%, 58.5%, respectively. For co-precipitation of zinc, manganese and iron, 5M NaOH solution was used for pH control. Then in order to synthesize Mn-Zn ferrite powder, it was investigated according to reaction temperature, agitation speed and O2 partial pressure. We could synthesize about 20 nm of Mn-Zn ferrite with spinel structure.

Jan 1, 2008

By A. M. Alfantazi, M. Boissoneault, D. B. Dreisinger, J. Synnott

"The effects of five commercially available foaming reagents (range of 0 to 25 ppm) namely Dowfroth 250, Saponin, Yucca, Licorice and Meta-Para Cresol on acid mist control, current efficiency, polarization behavior, and deposit morphology and orientation were investigated. The deposition was carried out using a bench scale electrolysis apparatus (cell volume 3L) at 500 Nm-2 and 38°C for 3 hours from Kidd Creek zinc electrolyte. The acid mist control capability of the various reagents was studied and compared by characterizing the foam layer generated during actual electrowinning conditions and by direct quantitative measurements of acid mist levels on top of the electrowinning cells. Within the range considered, the addition of these reagents reduced the current efficiency, refined the grain size of the deposit, and changed to preferred orientation of most of the deposits. Among the reagents tested, acid mist measurements indicated that Licorice and Dowfroth 250 were the best acid mist suppressant at emissions of 0.30 mglm3 and 031 mg/m3 respectively while Yucca and MPC produced the most mist at 3.0 mg/m3 and 33 mg/m3 emission rates, respectively.IntroductionMost of the world's primary zinc is produced via a combined roast-Ieach-purificationelectrowinning process. Depending on the electrolysis conditions, several additives may be added to the electrolyte. Some (e.g. glue, antimony, sodium carbonate) are added to mainly counteract the detrimental effects caused by impurities while others (e.g. licorice, Saponin) are used as foaming reagents to prevent excessive acid mist formation. Acid mist emission is a problem in many electrolysis operations because it corrodes the equipment and is a health hazard to the workers in the tankhouse as well as it pollutes the environment. Due to recent trends towards more environmental protection and more stringent in-plant hygiene, there is an increasing need to minimize these aerosols. In order to eliminate or minimize these aerosols foaming agents are usually added to the electrolyte to produce a foam layer on top of the electrolyte, thus trapping most of the mist. The ideal foaming agent would trap all of the mist and would not interfere with the electrowinning process. It is also evident that the reagent toxicology, cost and availability are important factors that need to be considered.Review of the available literature clearly indicated that very little work has been done in the past on the subject of acid mist control in electrowinning operations particularly in the area of foaming and anti-misting properties of surfactants. Two papers [1,2] have reviewed briefly the existing technologies for acid mist control. Recently, most of the work in this area has focused on the development of special mechanical devices that could be attached to the electrodes and control the mist generation at the source before it is emitted to the cellhouse [2-5]. On the other hand, extensive body of literature exists that deals with the effects of anti-misting reagents on the electrowinning aspects [6-7]."

Jan 1, 1997

By Zviad Kovziridze

The problems related to the production and research of SiC-Si3N4 composite are presented. The technology of producing the protective casings for tips and thermocouples is developed. Optimum composition charge and technological parameters are defined. The results of casing testing at production plants are presented.

Jan 1, 2006

By Guo Xian Jian

In this paper, an alternative process to recover the value metals from polymetallic gold ore by FeCh leaching was proposed. In the process, gold was recovered by direct cyanidation from the leaching residue, the isolative electrolyte in chloride solution was selected to recover lead, the cementation with copper powder was used to recover silver and the solvent extracting was applied to recover copper and zinc. The total recovery of gold, lead, copper, silver and zinc in the process is 90.8%,96.05%,84.3%,81.98% and 54% to the bullion of gold, lead and silver and sulfate of copper and zinc, respectively. The process conditions selected for FeCh leaching are the temperature of 104°C, leaching time of 6 hours, Fe3+ content of 140 g/l and stoichiometry of FeCl3.

Jan 1, 1996

By P. D. Navarro

The behavior and operability of LIX 1104SM extraction was studied at laboratory scale on the Solvent Extraction at Sb3+, from high concentration sulfuric acid. In order to evaluate the reactant batch tests were made at laboratory scale as well for extraction as for re-extraction of Sb3+. Experiences achieved were: extraction kinetics, temperature effects, selectivity tests and re-extraction selectivity. A extraction kinetics was found, reaching equilibrium in 2 min, high selectivity of Sb3+ extraction in front of Cue , existing As5+ co-extraction and Fe3+ At the re-extraction stage, equilibrium was reached in 3 min, getting high Sb3+ re-extraction efficiency with HCl concentrations within 6 and 8 M. A high selectivity was achieved on Sb3+ re-extraction in front of As+5, existing Fe+5 re-extraction.

Jan 1, 1999

By Yan Fu, Chuanlin Fan, Xiujing Zhai, Yongfeng Chang, Binchuan Li

"The mechanism of the selective chlorination of nickel and cobalt in reduced limonitic laterite was investigated. Reduced ores were obtained from the reduction roasting of a limonitic nickel laterite. The thermal decomposition of related chlorides and the selective chlorination of the reduced ore were carefully studied using Differential Thermal analysis - Thermogravimetry (DTA-TG), X-Ray Diffraction and chemical leaching methods. In the temperature range of 300 - 500 °C, aluminum chloride hexahydrate was chosen as chloride agent. During the selective chlorination, reduced ore was partly chlorinated by hydrogen chloride generated from the thermal decomposition of chloride agent. Then the oxydrolysis of ferrous chloride re-generated hydrogen chloride was used to further the chlorination. Finally, iron was mostly rejected as hematite, while nickel and cobalt were selectively chlorinated. More than 91 %Ni , 90%Co and about 4%Fe in the chlorinated ore was extracted using a water leaching method.IntroductionLimonitic nickel laterite is an important nickel reserve, which is rich in iron in the form of goethite and has low contents of magnesium, aluminum, silicon, and other elements. Goethite is the main nickel-bearing mineral in the laterite [1]. Nickel is generally present in goethite in three modes: (a) associated with amorphous or poorly crystalline goethite, (b) weakly adsorbed to the crystalline goethite surface, and ( c) as lattice substituents [2]. In addition, cobalt in limonite was found to be associated with a manganese phase rich also in nickel [3]. These results indicate that the extractions of nickel and cobalt are highly dependent upon the degree of the decomposition of the nickel, cobalt-bearing minerals.For the selective extraction of nickel and cobalt from limonitic laterite, the ore is usually processed by hydrometallurgical methods, including high pressure acid leaching (HPAL) [4] or reductive roasting - ammonia leaching (Caron process). However, there are still some disadvantages in these processes, such as the expense of autoclaves and scaling problems in HP AL [ 4, 5], and relatively low overall metal recovery, large energy and reagent requirements for the Caron process."

Jan 1, 2011

By S. A. Platias

Large amounts of dunile tailings can be recycled for olivine produdion from the existing beneficiation adivity of chromite ore in northern Greece. This olivine production aims at the preparation of a material suitable for the substitution of the environmental hazardous quartz sand in the foundries of Europe In smelting of chromite ore the losses that occur ore usually of the order of 6-8% Cr that report in the slag. Most of this is in the form of oxides that cannot be recovered, but usually 30-35% is in the form of FeCr alloy that can be recovered by gravity methods. About 90% of the produced slag is sold for road construdion after crushing to a desired grain size. Finally, recycling of chromites sludges from the ferrochrome produdion plant, through the preparation of pellets, improved the total chromite yield by 2%.

Jan 1, 1996

By Greg Dowling, Jun Ge, George Shannon, Shufeng Yang, Yongfeng Chen, Lifeng Zhang

"Inclusions in 316L stainless steel ingots poured using two different upgate designs – a traditional upgate and a swirl upgate - were investigated using SEM and ASPEX automated inclusion analysis. The main inclusions were high SiO2 inclusions, MnS inclusions and SiO2-Al2O3-CaO inclusions. More inclusions were detected at the top of the ingot than other places in vertical direction, and more inclusions were at the edge of the ingot than other place in the radial direction. With swirling upgate there were more K- and Na- bearing inclusions than that with the traditional upgate indicating possible more serious flux entrainment with the swirl upgate.IntroductionIngot casting still is very important for production of special steel grades including high carbon chromium bearing steel, thick plate, seamless tube, forgings, bars, and wire rods [1] . During the bottom teeming process, molten steel enters the trumpet and passes through the spider into the runners. Molten steel then enters the ingot mold through an upgate near the end of the runner. In the early stages of filling a mold, a mold flux bag hung in the mold were burnt and the mold flux will cover the top of the rising steel to protect the steel from being reoxidized, acting as well as act as a thermal insulator. So far, some efforts on studying inclusions characteristics in the ingot have been reported. A review paper on the control of inclusions during steel ingot casting was published by Zhang et al. [2] Zhang also studied Inclusions in bottom-teemed ingots of plain carbon steel and found that the >20µm inclusions originated from either the entrainment of mold flux of the reoxidation during teeming process. [3] The results of Nagendra and Du showed that there were more inclusions in the centre part of the ingot [4]. Eriksson et al reported that the composition of inclusions was more complex in the mold samples in comparison to the ladle samples, and more inclusions in the mold were found than in ladle because of the reaction between the mold flux and the molten steel [5]. It was reported that SiO2-CaO-Al2O3 inclusions originating from mold powder with reoxidation product Al2O3 as a part, and there were more inclusions close to the side wall than the center of the ingot in the radial direction. [6]. A more recent investigation showed that four main types of inclusions in runner samples were classified: oxides, sulfides, complex and carbon-nitrides. [7] The flow pattern in the mold during filling has been found to be an important factor regarding inclusions in the ingot. In the early stages offilling a mold, steel enters the mold through the entry nozzle at a high velocity. The effect of the resulting turbulence on the meniscus can lead to the entrainment of mold flux. Efforts have been paid over the years to find methods to reduce the velocity of the molten steel entering the mold, such as using opening angle of the inlet nozzle [8], using swirl blade at the runner [9], using a divergent nozzle combined with a swirling flow generated in the nozzle [10-11]."

Jan 1, 2012

By Toshiyuki Hiranami, Keizou Uematsu

"AbstractionSpray freeze drying method was proposed to fabricate ·ceramic: powder granules for high performance ceramics. Obtained granules and their green compact were characterized by SEM and immersion liquid technique. Granules have a spherical shape of about l 00 µ m in diameter, ·and no binder segregation was found with the immersion liquid technique. The granule had sufficient strength for usual handling, while the strength was much lower than that of granules prepared by conventional spray-drying. Unlike the conventional green compacts, granule interfaces were not observed in the green body made with the spray-freeze dried granules.IntroductionIt was well kn9wn that spray-dried granules have binder segregation layer on their surfaces. The trace of this segregation layer survives in the later processes i.e. compaction and firing, and behaves as fracture origins in the sintered bodies. The origin of this problem is solvent drying process from slurry droplet surface in spray drying system. As alternative method we propose a freeze drying process for granule preparation, in which solvent is remove by sublimation though the process, binder segregation can be prevent.In this study, we applied spray freeze drying method to fabricate alumina powder granule, and characterized the obtained granules, and their green compacts and sintered bodies.Experimental procedure.Alumina powders and additives aqueous solution were mixed for 24 hours using a ball mill to· prepare the slurry for spray freeze drying. .The solid loading of the slurry was 30vo1%. Deflocculant (PAA-NH4 type) was added 0.5mass%, and the binder (PVA). 1.0, 2.0 or 3.0mass% of alumina. Obtained slurries were sprayed into liquid nitrogen to make frozen granules. The granules were freeze dried.For the characterization of the granules, immersion, liquid technique observation and single granule strength test were carried out. Strength of individual granule wa5 measured using micro compression testing machine (MCTM, SHIMADZU). Granule strength was calculated from following equation."

Jan 1, 2000

By M. Omneya El-Hussaini, M. Galal Abdel Wahab, A. Mohamed Mahdy, M. Fathi El Shahat

"Lead-zinc mineralization is distributed in Egypt along the Red Sea coast between El Qusier and Ras Banas. A representative sample from Um Gheig was collected and ground to -60 mesh for the mineralogical study. It contains hemimorphite (Zn2SiO4.H2O), sphalerite (ZnS), galena (PbS), calcite (CaCO3) and dolomite (CaMg(CO3)2) beside the gangue minerals gypsum (CaSO4.2H2O) and hematite (Fe2O3). Cadmium seems to be incorporated in the crystal structure of the zinc-lead minerals. The chemical analysis of Um-Gheig representative sample revealed that, it contains 16% zinc combined with 0.1% cadmium, 2.3% lead and 0.1% boron beside other elements.Pug and agitation leaching were performed on samples ground to -200 mesh to achieve the maximum dissolution efficiency of cadmium with respect to other elements. Cadmium leaching efficiency reached 90% by using 40% H2SO4 at S/L ratio 1/2 and stirring time 2 hours at 80o C. Cadmium was then separated as yellow precipitate of CdS from the sulfate leach liquor containing 0.9 g/l Cd, 145 g/l Zn, 0.15 g/l B and 0.01 g/l Pb. Separation of cadmium was carried out by direct precipitation using Na2S as well as H2S. The recovery of 94% cadmium free of zinc was achieved.IntroductionLead-zinc ores occur in Egypt in a few localities distributed along the Red Sea coast between El Qusier and Ras Banas. Um-Gheig Pb-Zn ore is a replacement deposit in limestone and calcareous sandstone in the basal series of the Middle Miocene rocks. The reserve of the ore deposits has been estimated by Soviet and German Experts to be about 900,000 Ton, Bishai [1]. As has been mentioned, zinc is a common element and cadmium is comparatively rare in almost zinc minerals. It was estimated that zinc is 200 times as abundant as cadmium. According to Bodas [2] about 2.1% of cadmium was carried by the Zn mineral hemimorphite (15.3% Zn) in Thailand. Also, Onal et al., [3] found that 164 g/t Cd was carried by Pb–Zn ore sample containing 10.17% Pb and 10.98% Zn from Aladag in Turkey. Cadmium metal has gained great importance due to its wide applications in civil and navy purposes as well as in nuclear field. It is characterized by its ability to absorb thermal neutrons during the chain reaction inside the nuclear reactors. It is also used in the manufacture of sheets which directed the chain reactions [4]."

Jan 1, 2008

By Andreas H. Vassiliou

Organic materials are major constituents of the ore in several uranium deposits. Some of these deposits have been described as "urano-organic" because, the organic materials are believed to have provided the dominant control for the accumulation and deposition of uranium and are directly and intimately intermingled with the uranium. The nature of these urano-organic deposits has been problematic in terms of (a) the origin of the associated organic materials and (b) the specific form of' occurrence of uranium. The organic materials in urano-organic deposits have been genetically related to both coal and petroleum or their progenitors or deriva-tives. Analytical data presented here (infrared, chemical. D.T.A.) suggest that coaliferous materials or related plant derivatives represent the main source of the organic fractions in practically all major urano-organic ores analyzed from the Colorado Plateau and other areas. Recognition of the specific form of occurrence of uranium in urano-organic deposits has been problematic mainly because the uranium is usually in an extremely fine-grained and disseminated state in the organic matrix. Electron microprobe and X-ray diffraction analyses presented here show that fine-grained uranium minerals, specifically uraninite or coffinite. are disseminated in the organic matrix as the predominant form of uranium in most major deposits; however. the presence of true organo-uranium compounds is also suggested for some deposits.

Jan 1, 1981

By Gustavo E. Lagos

Mining is one of the oldest and most important productive activities in Chile. In the latter half of the 80's &d during the 1990's Chilean mining has experienced explosive growth fundamentally due to legislative changes which have encouraged an influx of foreign capital. Fine copper production has grown from 1,4 million tons in 1987 to 3,4 million tons in 1997. Gold production has increased from 17.03 tons in 1987 to 49.46 tons in 1997. In both cases private investment has driven this growth. The direct impact of mining on the Chilean economy has been considered one of the fundamental pillars of the growth of the country in the last years. The indirect impact that has generated on the other sectors of the Chilean economy and in particular the regional economies, has not been analyzed. This paper outlines a methodology for estimating the impact of mining investment and mining operations in different sectors of the Chilean economy at both regional and national levels. It applies this methodology to the case of Minera Escondida, the largest copper mine in the world, analyzing its economic impacts on the regional and national levels.

Jan 1, 1999

By Hector M. Henao

In order to provide the thermochemical data regarding the slag system, which are of importance for sulfide smelting and metallurgical processes but still lacking, an experimental study was carried out on the phase relations and activity of iron oxide in the FeOX-CaO-SiO2 system at temperatures between 1300 and 1400 °C and partial pressures of oxygen between 10-9 and 10-4atm. First, the solubility of CaO and SiO2 in the solid FeO were obtained and the tie lines connecting between the solid wustite (FeO) or magnetite (Fe3O4) phase and the liquid phase were determined. Secondly, iso-activity lines for FeO in the homogeneous liquid region were determined, based on the activity of iron in the Pt-crucible used in the equilibrium experiments. The activity coefficient of FeO in this region was also derived from the composition of FeO and FeO1.5 in the liquid region. Finally, the effect of (CaO/SiO2) ratio in the system and partial pressure of oxygen on these thermochemical quantities is discussed.

Jan 1, 2006

By Wei-ling Wang, Ryosuke O. Suzuki, Xiang-ning Meng, Miao-yong Zhu

"A finite-element thermal-stress model of continuous casting mold is conducted to predict deformation of copper plates and its change with different cooling structure. The results show that deformation behavior of copper plates is mainly governed by cooling structure and thermal- mechanical conditions, deformation amount is related to structure geometry, and a small deformation mutation occurs in cooper-nickel boundary due to different properties. The maximum deformation of hot surface centricities of wide face locate at 100 mm below meniscus and that of narrow face locate at meniscus and terminal of water slots and significant curvature fluctuations on both sides of copper-nickel boundary. The maximum deformation of centricities is increased up to 0.05 mm with thickness increment 5 mm of copper plates, and maximum deformations are only depressed 0.01 mm and 0.02 mm with increments of 1 mm nickel layer thickness and 2 mm water slot depth respectively.IntroductionIn conventional continuous casting of steel, a large amount of sensible and latent heat of molten steel dissipate in primary cooling zone and make continuous casting mold under enormous heating load giving rise to thermal stress, deformation, high-temperature fatigue and creep not only depress mold life-span, but reduce casting stability [1] Many studies focused more on heat transfer, solidification and shrinkage of solidifying shell to provide inverse proposals for optimizing cooling system and even designing new taper of mold [2,3], but it is generally useless to those of having been manufactured or being put into production. Therefore, mold-related forward problems show necessity to be discussed deeply, and stress and deformation distributions based on special thermal conditions in mold should be analyzed in order to explore suitable cooling structure of mold directly. Samarasekera et al. [4] examined heat flow and distortion of two-dimensional longitudinal sections and investigated effect of cooling water velocity, copper plates thickness and carbon content on formation of rhomboidity and longitudinal comer cracks. O'Connor et al. [5] developed a three-dimensional mathematical model to compute thermo-mechanical state in thin-slab mold and calculated temperature and deformation of mold wall to assess roles of various process parameters on impacting mold life. Thomas et al. [6] predicted temperature, distortion and residual stress in mold and indicated increased distortion requires increased remachining, which reduces mold life and increased residual stress increases the probability of a catastrophic crack failure. Park et al. [7l determined heat-flux profiles in funnel-shaped and parallel thin-slab molds based on an inverse heat conduction model and thermocouple temperature measured in-plant and put them into three- dimensional finite-element thermal-stress model to predict temperature, distortion and residual stress of mold wall. Korie et al. [SJ focused on prediction of temperature, distortion and residual stress in mold and in particular to clarify that mold life is significantly affected by temperature and its rigidity, but little effect by mechanical including clamping force, bolt prestress, friction and ferrostatic pressure. Meng et al. [9l predicted temperature and thermal stress in a slab mold and analyzed effect by cooling system geometry and casting speed quantitatively. In present study, a three-dimensional finite-element thermo-mechanical model with type-switched element is transformed from previous heat-transfer finite-element model [9l, and mold deformation is simulated in order to shed light on thermo-mechanical behavior with special thermal conditions and different mold geometry at high casting speed."

Jan 1, 2013

By R. M. Luna-Sánchez

Electrochemical studies, particularly Evans? diagrams, have been employed in hydrometallurgy to simulate and explain the redox phenomena that take place at mineral and metal surfaces during operations such as leaching and cementation. However, despite their utility, in some cases, the combination of the cathodic and anodic branches, determined separately, does not reproduce the chemical environment present when both processes occur simultaneously on a specific surface. In the present paper, limitations of Evans? diagrams are analyzed through two examples: silver sulfide cyanidation and gold cementation on zinc. In both cases, the surface kinetics are sensitive to the local pH and cyanide levels. When the electrochemical oxidation of silver sulfide or the reduction of gold are performed in the absence of its corresponding redox reaction, the local pH obtained does not simulate the real situation and the combined reaction kinetics may be very different from those determined from the Evans? diagrams.

Jan 1, 2003

By U. Meyer, A. Alonso, P. Banios

The sampling of cathodes has changed with the introduction of the ISA-process in copper refineries. A Jernkontoret joint working group of refineries and rod plants from both primary and recycled copper plants has been investigating whether the actual sampling of cathodes is representative for this type of cathodes. As a first stage, samples were sent to the members of the working group with the objective to find an easy basis for a comparison of the results of the next stages. All samples show the same tendency for nearly all elements. In some cases, there may exist differences in calibration and for some elements the detection limits are too high, especially when Optical Spectrometry is used. In the second stage, discs were compared with melted samples to answer the question whether the punching of discs is sufficient for the quality control of the cathode. The analyses of the discs represent fairly well the cathode quality. There are differences between cathodes from different crops. Three punches are sufficient to determine the cathode quality. Finally, samples from various lots of cathodes were compared with samples from the rod produced from these cathodes. The impurity content of the rod corresponds to the impurity content of the cathode.

Jan 1, 2000

By Weyman Dunaway

This paper will present a description of the development and commissioning of the world?s most efficient process for manufacturing high purity aqueous zinc bromide. The method for making aqueous zinc bromide from metallic zinc and bromine comprises contacting zinc with bromine dissolved in a reaction solvent containing a metal halide salt. The reaction temperature is maintained at less than 60°C. The reaction solvent preferably comprises an alkali, alkaline earth, or transition metal halide; the halide salt preferably comprises a chloride or a bromide. One preferred method includes the step of recirculating the zinc bromide product stream back to the reaction vessel. The reaction vessel can be either a one stage or a multiple stage reactor. The resulting product stream is a high density aqueous zinc bromide solution. The process is so novel that Tetra Technologies, Inc. was awarded US Patent Number 6,036,937.

Jan 1, 2006

By Murray Johnston

New measurements have been made on the equilibrium distribution of selenium and tellurium between molten slag and metal phases. Distribution coefficients of Se and Te between magnesia-saturated calcium ferrite slag and copper or silver alloys were measured over the temperature range 1473 and 1673 K under controlled oxygen patrial pressures of 10-11 to 10-0.68atm. The results demonstrate that the minor elements are present in the calcium ferrite slag as the selenide (Se2-) and telluride (Te2-) respectively, up to a PO2 of 10-6 atm. As conditions become more oxidising, Te undergoes a transition to the divalent oxide whereas Se does not. Increasing the temperature was found to enhance partitioning of the minor elements to the slag. In terms of activities, at 1573 K, Se showed strong negative deviation from the ideal behaviour in the slag, while Te showed only slight positive deviation.

Jan 1, 2006

By Wantae Kim

In order to establish the optimized recovery process for heavy minerals from Korean beach sand, we investigated the several physical separation methods such as gravity and magnetic separation followed by mineralogical characterization. There was clear relationship between the particle size and heavy mineral content that heavy minerals were mostly concentrated in the particles below 100mesh. Gravity separation using the spiral and shaking table separators made it possible to concentrate heavy minerals by rejecting the light and coarse particles consist mainly of quartz and other non-valuable minerals. The high-intensity magnetic roll separator and subsequent induced magnetic separator were applied to fractionate magnetic particles according to their magnetic susceptibility. The content of TiO2 of high susceptible ilmenite-rich fraction was 43.98wt.% while those of ZrO2 of non-magnetic and magnetic residue were 6.78wt.% and 3.11wt.%, respectively.

Jan 1, 2006

By Dengfu Chen, Yunwei Huang, Mujun Long, Kui Lv, Pei Xu, Lin Bai

The surface temperature of continuous casting slab in the secondary cooling zone is a key parameter of production control. However, the accuracy of radiation temperature measurement of high temperature casting slab is greatly affected by the environmental factors, such as water vapor, spray, water film and other participational medias during continuous casting process. In this paper, the radiation characteristics of water vapor and its influences to radiation temperature measurement of continuous casting slab were investigated. Based on the database HITRAN 2004 and the measuring principle of monochrome thermometer & colorimetric thermometer, the measuring errors under different operating infrared spectral wavelength were compared. Results showed that spectral region with wavelength nearby 1.0μm or 1.6μm would be the optimum for high temperature infrared thermometer used under the conditions with moist steam, water spray and water film at the secondary cooling zone in steel continuous casting.

Jan 1, 2016