Search Documents

By Taiping Lou

The coarsening process of precipitates in non-equilibrium systems was studied, and then a physical model of coarsening was proposed. The coarsening process of CaO'TiO2 in MgO-TiO2-Al2O3-SiO2-CaO-CaF system was investigated. It is shown that the coarsening process by the model predicting is agreed with the experimental results.

Jan 1, 2000

By V. Gornitz

The Orphan mine uranium deposit, Grand Canyon, Arizona, is a cylindrical collapse-breccia pipe, 70 to 150 m in diameter and 500 m deep. Pipe fill was derived from the Supai Group, Hermit Shale, and the Coconino Sandstone. Uraninite, with Cu, Fe, Pb, Zn and Ni-Co sulfides is concentrated along the pipe boundary ring fracture (annular ring) and within the central porous sandstone matrix. There is some suggestion of vertical and lateral zonation of U with respect to Cu. Reduction of ferric oxide cement from red beds and recrystallization of carbonate, with formation of kaolinite preceded major ore deposition. Early Ni sulfides, arsenides and disseminated pyrite were followed by massive pyrite, and botryoidal uraninite, which in turn was suc-ceeded by Cu, Zn and Pb sulfides. A second, later generation of uraninite was closely intergrown with hematite and base metal sulfides. Oxidation of primary minerals may have been associated with Tertiary regional uplift. The paragenetic sequence closely resembles that of other Grand Canyon breccia pipes, except for the extensive development of the distinctive uraninite-hematite association. Mineral assemblages at the Orphan suggest possible mixing of the metal-bearing solution(s) with a more oxidized fluid, containing soluble uranyl complexes. Homogenization temperatures of fluid inclusions in calcite (GO-lIO?C) at the Orphan fall within the lower end of the range observed at other breccia pipes.

Jan 1, 1987

By Chen Wen, Li Zhao-jia, Zhao Qiang, Ning Shun-ming, Tang Sanchuan, Wang Hong-qiang

"The carbon-burdened and cold-bonded pelletizing-electrosmelting process is used to dispose low-grade manganese, and the qualified rich-manganese slag is obtained. On the condition that reduction roasting temperature was 1000?, reduction time was 45min, particle-size was -1mm, reductant dosage was 1.6%, basicity was 0.3, smelting temperature was 1410?, smelting time was 60min, it had a good effect on the melting between slag and metallographic phase, the manganese content was 32.58%, manganese recovery was 92.16% in the slag; while the iron content was 94.40%, iron recovery was 95.32% in the metallographic phase. It was proved by the demonstration tests.IntroductionManganese is an important raw material for steelmaking, which is extensively utilized in modern industry, the consumption of manganese for iron and steel industry accounts for 90% to 95%. After mining over 30 years, the high-grade manganese resources drop markedly, especially with the hypergrowth of steel industry, the domestic manganese is far from the requirement, as a result, we have to buy significant quantities of manganese overseas. Besides, the property of imported manganese is more and more complex, and the high-grade and lump manganese decrease year by year, while the fines and high-crystal water manganese are on the increase. Therefore, how to make effective use of domestic low-grade manganese and intensify the manganese’s smelting is an effective approach to reduce the cost of manganese series ferroalloy and improves market competitiveness[1-4]. It has important practical meaning."

Jan 1, 2012

By Junji Shibata

Zeolite synthesized from coal fly ash has many intelligent properties such as cation exchange, adsorption, catalyst and so on. The suitable use of the zeolite, however, is not established in an actual commercial scale yet. From the viewpoints of an effective usage of coal fly ash and the zeolite obtained from coal fly ash, we propose the new concept for environmentally friendly usage of zeolite, in which coal fly ash safely returns to the soil with growing plants and purifying wastewater. This method can make great contribution to recycle of coal fly ash, to purification of high nutritious water and to tree planting.

Jan 1, 2002

By Leonard J. Friedman

Modern smelting systems using continuous, flash and/or oxygen smelting processes have a significant effect on the choice of sulfur dioxide control processes and system arrangements. Based on gases from an enriched air or oxygen smelting furnace and copper converters the paper reviews and analyzes alternate processes and system arrangements for recovery of sulfur dioxide. The work indicates the choice system to include a conventional sulfuric acid plant for converter gas and a liquid SO2 plant to handle the high strength smelting fur¬nace gas. The liquid SO2 plant would be used as a fly-wheel to damper the flow and SO2 concentration variations of the con-verter acid plant. Potential energy recovery alternates and product flexibility are also reviewed.

Jan 1, 1983

By Peter K. Liaw, Charlie R. Brooks, David C. Joy, Wei Zhao

In this paper, effects of oxidation, porosity and fiber-fabric stacking sequence on flexural strength of a continuous silicon carbide fiber (SiCr) fabric-reinforced SiC ceramic-matrix composite (CFCC) were studied. The failure mechanisms were correlated with flexural strengths of CFCC samples, both before and after oxidation. Microstructures and fractography were investigated using scanning electron microscopy (SEM). The chemical change after oxidation, such as Si, C, and 0, and their distributions, were detected by the SEM energy-dispersive X-ray spectroscopy (EDXS) line-scan chemical analysis technique. These effects on the strength of the CFCC can be attributed to following reasons: (i) The decrease in the flexural strength after oxidation is mainly due to degradation of the strength of Nicalon fibers and the damage of fiber/matrix interface both caused by high-temperature chemical reactions, (ii) Porosity is not too important in affecting the strength of the CFCC, when the bonding of the forced flow chemical vapor infiltration (FCVI)-SiC matrix is stronger than that of the fiber/matrix interface. However, a higher porosity content will be harmful, because higher porosity will both decrease the effective elastic modulus of the FCVI-SiC and make pore-linkage easier to occur, which is more likely to cause premature failure, (iii) The variation in the lamina stacking sequence of the CFCC changes the elastic stress distributions along the thickness direction of specimens, the magnitude of ceramic matrix-cracking stress, the effective elastic moduli of the laminate, and different crack initiation sites as well as different failure modes, and thus, leading to the scatter in the flexural strength of the CFCC.

Jan 1, 1998

By Toru H. Okabe

As part of a systematic study on the thermodynamic properties of complex nitrides, phase equilibria of the system Li-M-N (M Mg, AI, Ga) at 900 K were investigated. An attempt to determine the thermodynamic properties of complex nitrides was made by using the galvanic cell method, which utilizes LiMgN as an electrolyte under nitrogen atmosphere. The electromotive force (Emf) of the cell at temperatures between 800 and 1100 K was measured. While the Emf of the cell at 900 K was measured to be 0.137 V, data discrepancies of ±0.03 V were found. It was difficult to determine temperature dependence of the Emf. The Gibbs energy change for the reaction, 113 Li3N (s) + 1/3 Mg3N2 (s) = LiMgN (s), at 900 K was determined to be !'J.Go, (LiMgN) = -13.2 (±2.9) kJ/mol. Using thermodynamic information on the binary nitride from literature, the standard Gibbs energy of LiMgN was derived to be !'J.Go f (LiMgN)= - 121 kJ at 900 K. The thermodynamic stability range of nitride was discussed by constructing isothermal chemical potential diagrams that provide a better understanding of the stability region of the LiMgN phase. The diagram was found to be in good agreement with the isothermal phase diagram determined by the alloy equilibration method. Although the obtained data includes large uncertainties, the results provide a better understanding of the thermodynamic stability of nitrides. The potential application of this complex nitride to nitrogen chemical sensors or a medium for controlling nitrogen potential is also shown.

Jan 1, 2003

A comprehensive numerical capability for the analysis of Thermal Spray (TS) systems consisting of a three-dimensional compressible, turbulent flow Navier-Stokes model and a multi-phase particle flow model in Lagrangian formulation, was developed. This capability is validated for a set of flow conditions typical for TS. The developed methodology is used for analysis of the JP-5000 TS gun gas and coating powder flow conditions. Modeling and analysis of particle/turbulent eddies interaction is performed. Details of gas flow field, particle temperature, and particle velocity histories, and particle temperature, velocity profiles in the system are presented. For the validation of numerical analysis, the computed results are compared with available experimental measurements. The flow phenomena for different flow parameters are analyzed and explained as the results of gas dynamics and heat and momentum transfer between the gas and particle phases. This methodology can be used for process control and reliability improvement, and has the potential to significantly improve TS gun performance through control of its parameters.

Jan 1, 1996

By Karl A. Gschneidner

The magnetocaloric effect has been known for 120 years and has been utilized for cooling about 70 years. But in the last four years significant advances have been made to show that magnetic refrigeration is a viable and competitive cooling technology. Most of the work has focused on reciprocating devices, but rotary apparati are being developed. To date the magnetocaloric properties have been characterized for more than 200 materials. The magnetocaloric effect behaviors have been classified into three types of behaviors. The most common one is found in magnetic materials which exhibit a second order magnetic phase transition. Magnetic materials which exhibit a first order magnetic phase transition account for the second group of materials. Materials which exhibit multi-magnetic phase transitions make up the third group. The best candidate materials for magnetic cooling over the range from -4 to -1 350 K are also presented.

Jan 1, 2002

By Onwukamike, Onyedika G. O, Ogwuegbu M. O. C., K., Onyenehide C

A detailed mineralogical and elemental characterization of a lead (Pb) ore deposit from Ishiagu, Ebonyi State, Nigeria was carried out with XRD, SEM-EDX, and ICP-OES based mappingtechniques. The results show that the most dominant and valuable metal is lead (Pb = 95.02%, mass fraction). The main mineral is galena. Ilmenite and sphalerite occur as minors, which account for 2.71% and 0.80% respectively. Elements like Al, Ca, Mg, Ti, Na, Mn, Si and Sn occurred in trace amounts and are disseminated in the entire ore body.The surface and interrelations of the crystals were examined with x-ray mapping and the result shows the pattern of dissemination of the minerals within the ore body.

Jan 1, 2015

By D. H. H. Quon

Results of a study conducted to determine the properties of iron ore pellets made from Mount Wright and Carol Lake ore concentrate fines with partial and full substitution of bentonite by several organic binders are presented. Carboxy methyl celluloses 7H and 6TL, hydroxy ethyl cellulose (natrosol) and modified guar gum all produce pellets of acceptable wet, green and dry strength. However, when fully substituted, an inorganic binder such as calcium carbonate is required for satisfactory strength development after induration. Mixing the Carol Lake ore with Mount Wright ore in a 50-50 ratio also achieves the same result. The failure of the Carol Lake ore in the pelletization process is attributed to the low hematite content of the ore. The results are very similar to those from the extrusion studies reported earlier (8).

Jan 1, 1989

By Masahiro Sasaki, Wu Kepeng, Chang-Yong. Kang, Kohji Okada, Naohiro Igata, Kazuya Miyahara

"The damping capacity of the Fe-12 mass % Cr-6 to 30 mass % Mn alloys has been investigated. Particularly the effects of microstrucutre composed of the phases of a , a ' , y , and e on the damping capacity have been clarified. Various fraction of these phases were formed depending on the Mn content and cold work degree. The combination of 22 mass % Mn and 50% cold rolling formed the largest volume fraction of e martensite and showed the highest damping capacity. The other phases of a, a' and y had very small effect on the increasing of damping capacity.IntroductionFe-Mn alloys are known to be one of the high damping capacity materials [l-3]. In the present research, the damping capacity of the Fe-12 mass % Cr-6 to 30 mass % Mn alloys, in which 12% Cr is added for the improvement of corrosion resistance of the Fe-Mn alloys, has been investigated. Particularly the effects of microstrucutre composed of various phases of a (bee), a ' (bet martensite), y (fee), and e (hcp martensite) on the damping capacity have been clarified. The results of preliminary research on Fe-Cr-Mn alloys are reported by Igata et al. [4] Various volume fraction of these phases were formed depending on the Mn content and cold work degree. The combination of 22 % Mn and 50% cold rolling formed the largest fraction of e martensite and the measurement indicated clearly that e martensite had the largest effect on the damping capacity. The other phases of a ' y and a I had very small effect on the increasing of damping capacity."

Jan 1, 2000

By Alan J. Hurd

"New insights into the development of microstructure in sol-gel films have recently been revealed by several diagnostic techniques, including imaging ellipsometry, ""chemical imaging"" by fluorescent tracers, light scattering from capillary waves, and finite-element modeling. The evolution of porosity during the continuous transition from dilute sol to porous solid in restricted geometries such as films and fibers is becoming clearer through fundamental understanding of evaporation dynamics and capillarity.IntroductionWith sol-gel processing, the full flexibility of solution chemistry can be exploited to make ceramic films and fibers with well controlled compositional characteristics. No less important is the ability to tune porosity and connectivity for specific applications such as optical and electrical coatings and membranes. Since the chemical and physical factors that determine the microstructure are not entirely understood, new diagnostics applied to sol-gel processing are welcome.Sol-gel films and fibers are distinguished by processing that takes a sol through continuous stages of increasing concentration and connectivity of a solid precursor. The liquid carrier is usually volatile or, at least, volatilizable through heat treatment. During deposition through states of increasing solids concentration, this sol might gel, as in bulk sol-gel processing, however, the gel state may be a fleeting transient that quickly empties of liquid. Nevertheless, the structures formed in solution during this stage influence the structure of the final solid. In particular, porosity is likely to be a remnant of networks formed in the sol-to-gel transition. Here we report on experiments whose goal is to discover the factors involved with porosity development."

Jan 1, 1994

By V. Ramachandran

In view of the increasing environmental regulations that have been promulgated in the last 30 years, non-ferrous smelters and refineries have learnt to handle effectively the process waste streams that need to be bled from the system for impurities' control The cations of concern are copper, lead, zinc, cadmium, mercury, thallium, nickel, silver, sodium and potassium. Anionic species of arsenic and selenium also need to be addressed, Sulfates and chlorides-not a major concern at present-have come under scrutiny in the recent past. The current paper reviews several treatment options with reference to a) types of waste streams processed b )process chemistry c)discharge options and recovery of treated water and d) sludge disposal The long term goal of any smelter and/lor refinery should be to achieve zero liquid discharge from the plant. Methods to obtain zero discharge are discussed.

Jan 1, 2003

By Leonard Harris, Rosa H. Harris

"It is becoming increasingly obvious to mining and exploration companies, when operating overseas, that their activities should not conflict with the interests of the surrounding communities. The world's largest gold heap leach operation, Minera Yanacocha has installed community assistance programs in Peru concerned with health, education, electrification, agricultural assistance and road improvements. The programs are conducted with joint venture partners consisting of the company, the community people, the contractors and suppliers, government and non government organizations and a ladies association composed of the employees' wives and female staff.IntroductionThe l 990's is the decade highlighted by enormous investments in mineral exploration and mining projects in the developing world. Figure 1 illustrates the distribution of exploration spending by mining companies in 1995."

Jan 1, 1997

By V. Montenegro

Smelting of copper concentrates in Teniente Converter produces highly oxidized slag, containing from 4 to 10 % Cu and from 15 to 25 % of Fe304. Copper recovery requires magnetite reduction at a level of 5%, determining the degree of cuprous oxide co-reduction and the liberation of copper matte inclusions. The rate of slag reduction is controlled by the mass transfer to the reaction interface. Slag stirring affects the rate of reduction and enhances coalescence of mechanically entrained copper matte inclusions. Slag reduction and sedimentation in the AC electric furnace is a commonly used method of slag cleaning. Utilization of DC electric furnace creates beneficial conditions introducing slag electrolysis additionally to chemical reductions with carbon of coke and electrodes. Application of external magnetic field, interacting with a direct current in an electric furnace, induces magnetohydrodynamic phenomena, such as intensive stirring and electromagnetic buoyancy force acting on inclusions. Laboratory scale research in simulated DC electric furnace with a superimposed magnetic field showed a significant acceleration of the rate of slag reduction and copper removal. Continuous measurement of gas flow and composition allowed for determination of the reduction rate along the time. Application of external magnetic field in the reduction of the industrial slag in a crucible simulated DC electric furnace results such as the increase of the reduction rate from 2 to 3 times, compared with the identical conditions in the AC electric furnace. Interaction of non-homogeneous electric field with crossed permanent magnetic field induces vigorous slag stirring, enhance mass transfer and accelerate the rate of the slag reduction. Additional participations of the slag electrolysis in the magnetite and cuprous oxide reduction as well as the acceleration of the settling of the inclusions by the electromagnetic buoyancy force affect the slag cleaning intensification.

Jan 1, 2003

By S. W. Ip

Over the years, the importance of surface and interfacial phenomena has been neglected by the copper-nickel industry. As a result, little data on the surface and interfacial tension of the Ni matte and slag system are available in the literature. In view of the scarcity of information in this area, the surface tensions of the Ni-Fe-S system together with the Ni-Fe-S and fayalite type slag system were measured using the sessile drop technique. Drop images were obtained by X-ray radiography. For the Ni-Fe-S system, the results showed that the surface tension of the matte increases with matte grade. The surface tension behavior with changing matte grade showed a slight negative deviation from ideality. This indicated that FeS is slightly surface active in the nickel matte system. Results also indicated that small increase in sulphur content in the matte can decrease the surface tension quite significantly. The measured surface tension of the Ni-Cu-S system showed a linear relationship with the Cu2S content in the matte. The surface tension decreased with Cu2S content. Interfacial tension measurements showed a similar trend. That is, interfacial tension increased with increasing matte grade. The presence of MgO (-1.5%) and A12O3 (-6%) in the slag does not affect the interfacial tension value. Effects of matte surface tension on phenomena such as entrainment of matte in slag and infiltration of matte into refractory pores are discussed. The calculated flotation coefficients indicated that flotation of nickel mattes cannot be avoided by changing the matte grade. Filming of matte on bubbles can occur below a matte grade of about 19% Ni3S2. As for infiltration, refractory bricks containing high Cr2O3 will be easily wetted by matte regardless of matte grade. Therefore, bricks containing high Cr2O3 can easily be infiltrated by liquid matte.

Jan 1, 1993

By Jamil M. Khalifeh, Shadia J. Ikhmayies, Bothina A. Hamad

"We computed the optical properties of the cubic niobium nitride (o-NbN) compound using the full potential linearized augmented plane wave (FL-LAPW) method within density functional theory (DFT). The complex dielectric function and optical constants, such as optical absorption coefficient, refractive index, extinction coefficient, energy-loss spectrum, and reflectivity, are all calculated and compared with experimental results. The behavior of the computed quantities is similar to that obtained experimentally, but the optical positions are shifted to lower energies. This shift was related to the strong interband transitions, which are located at energies higher than 5 eV for NbN- as they are for IV B transition-metal mononitrides- and they appear in the computed spectra and not in the experimental spectra. These interband transitions simply shift the position of the reflectivity edge or the screened plasma frequency to the longer wavelength side.IntroductionIn recent years, NbN, as a transition metal nitride, has become a very popular material due to its high hardness, melting point, wear resistance, chemical inertness and temperature stability, which makes it suitable for use as emission cathodes in microelectronics and sensors, optical films and micro-mechanics etc [l]. Niobium nitride has long been known as highly polymorphic material, for which several crystalline structures have been reported in the literature [2]. These structures include the well known super-conducting rock-salt (Fm-3m, or Bl) structure (o-NbN), the hexagonal structure with space group p63/mmc and prototype Fe2N (18fuN), the hexagonalstructure with space group p63/mmc and prototype NiAs ~-NbN) and others.There has been a lot of computational studies for the structural and electronic properties ofNbN [3, 4-7], but according to our knowledge there is not any computational work that has been devoted to study the optical properties of this transition metal compound. At the same time a number of authors had performed experimental work in this direction. For example, Xin-kang et. al [l] studied the microstructure and optical properties of magnetron sputtered NbN thin films. Torche et. al [8] studied the composition, structure, electrical and optical properties of nonstoichiometric niobium nitrides. Newport et. al [9] investigated the reflection and transmission spectra of cubic niobium nitride films, and Tanabe et. al [10] had investigated the optical parameters and reflectivity of reactively sputtered NbN thin films by using in situ ellipsometry."

Jan 1, 2013

By Mario H. Castro-Cedeno

"A design for a handheld MEMS chemical detector is proposed. The detector will be used to detect trace amounts of chemicals in air. It can detect drugs, toxic chemicals and/or explosives. The proposed detector will use ion mobility spectrometry (IMS), a technique that is well known for accuracy and has been used in the past in suitcase sized chemical detectors. The separation and detection of the chemicals occurs in the drift channel and the process was modeled using the finite element method and CoventorWare modeling software. A manufacturing process sequence for the drift channel is proposed and was demonstrated.IntroductionThe goal of this effort is to design, mode~ and prototype a MEMS chip that will be the key component in an ion mobility spectrometer (IMS). This technique uses and asymmetric potential to separate the various ion species in a stream of incoming air [1-4]. One advantage of IMS is its ability to separate chemical species from air at atmospheric pressure and temperature. This is a requirement for a simple to use handheld drug or chemical detector. IMS can be used to detect drugs, toxic chemicals and explosives and it is well known for accuracy in detecting very small amounts of chemicals. This chemical detection technique has been used in the past, but not in handheld detectors.One variant of IMS is the high-field asymmetric waveform ion mobility spectrometry or FAIMS [3]. The FAIMS process, shown in Figure l, works as follows: a gas sample is admitted into the instrument where gas molecules are ionized, typically by a weak radioactive isotope source, ultraviolet light source; and more recently through field emission. The ions move along the length of a channel while they are separated in the transverse direction by an asymmetric electrical potential. The potential, in the form of an asymmetric waveform, causes relative motion between the various chemical species. The species that hit the charged top and bottom plates are neutralized and only those ions that move along the center are detectable as charged chemical ions at the end of the channel."

Jan 1, 2004

By John A. S. Green, J. Gilbert Kaufman, Subodh K. Das

"The aluminum industry is a leading proponent of global sustainability and strongly advocates the use of recycled metal. As the North American primary aluminum industry continues to move offshore to other geographic areas, such as Iceland and the Middle East, where energy is more readily available at lower cost, the importance of the secondary (i.e., recycled metal) market in the U.S. will continue to increase. In the past, the recycling industry had been synonymous with the collection of aluminum beverage cans. However, as the opportunities for aluminum recycling have multiplied in motor vehicles, building and construction, and aerospace, these market are getting additional scrutiny for optimization of recycling strategies.Accordingly, the secondary industry can now draw upon a much wider range of product forms and alloys for its raw material, but this in turn brings issues of alloy sorting, impurity content, and control as the material is remelted and recycled into new product forms. The purpose of this paper is to take an integrated, industry-wide approach to look at the recovery of material from demolished buildings, shredded automobiles, and aging aircraft, as well as from traditional cans and other rigid containers. Attempts will be made to assess how the different alloys used in these separate markets can be recycled in the most energy efficient manner.IntroductionIn his recent book “Aluminum Recycling”[1], Mark Schlesinger points out that in traditional extractive metallurgy, the raw material used to produce a metal is mined from the earth and then is separated from other gangue minerals and impurities. In aluminum recycling, however, the ore body consists of scrap metal found on the ground, rather than in it. He further notes that scrap comes with its own variety of gangue and impurities such as painted coatings, other metal attachments, and even dirt and other contaminants. So, while the recycling process still requires some refinement and expenditure of energy, the effort and energy involved is much less than traditional mining."

Jan 1, 2008