Search Documents

By Gennaro G. Marino

Site conditions at several shallow room and pillar mines in Illinois are described and compared with the charac¬teristics of the subsidence profiles at the ground surface. The shape and magnitude of the subsidence profiles were found to be closely related to the thickness of the soil and rock over-burden the percent extraction of the coal, and the shape of mine pillars. The room and pillar mines were located at a shallow depth (from 112 to 220 ft), beneath flat to gently rolling terrain. Thickness of the coal seams ranged from 5 to 9 ft and at all sites was underlain by underclays. This information has been developed in order to improve techniques for evaluating the subsidence potential at sites within the Illinois coal basin. he results presented form a small portion of the work carried out by the University of Illinois with Illinois Abandoned Mined Lands Councils and the U. S. Bureau of Mines at the Minneapolis Research Center in Minnesota (Marino and Mahar, 1985). Presented in the paper are the modes of mine failures observed for Illinois room and pillar mines, an overall summary of the site geologic and mining condi¬tions, case histories of each mode of failure, a comparison of sag profiles, and then an empirical relationship between the site conditions and the maximum sag subsidence. The most ideal case histories are presented to illustrate fundamental behavior. A brief of the Paper is given in a summary and conclusions section.

Jan 1, 1984

By Robert Kimutis, Ke Yang, Yi Luo, Jianwei Cheng

"Surface subsidence processes, especially those associated with a longwall mining operations, could cause operational and/or safety problems to railroads. For railroads with normal amounts of traffic, both the limited time window between traffic and the limited space available make the efforts to return the railroad back to its original state nearly impossible. In order to ensure the safe operation of a subsiding railway, the partial lifting method has been developed and applied. This paper describes the principle and application of the method. A case of applying this method to mitigate subsidence effects on a long section of railway has been demonstrated.INTRODUCTIONMaintaining an operational railway as it is experiencing a longwall subsidence process is not an easy task. The subsidence process may induce sufficient strain and curvature to cause problems to the railroad structures. Localized subsidence-induced slope often is significantly larger than the permissible ruling gradient of 0.7% for a locomotive to haul a loaded train reliably. In order to ensure safe operation, it would be ideal to instantly lift the railroad track back to its original level as it is subsiding. However, it is often impractical to do so due to the limited time windows available between railway traffic and the available space on the railroad base.A partial lifting method has been developed to keep the railroad operational under such limitations. The subsiding railroad track is raised by only a determined, partial amount of the occurred subsidence at a given time. By making such a determined adjustment, the railroad track can be maintained on a smooth and operational profile, and the high strain and curvature on the railroad structures can be reduced as well. To define a smooth railroad track profile in a subsided section the following two conditions should be met: (1) the maximum railroad gradient should be less than the permissible ruling gradient, and (2) the recommended amount of adjustment should be able to be made by the repair crew within the available time windows between scheduled railway traffic.The subsidence effects on a long section of railroad over two longwall panels have been successfully mitigated using the partial lifting method. The railroad experienced a maximum subsidence 89 of about 5 .0 ft (1.5 m) with the average subsidence along the entire length being about 3.45 ft (1.05 m). However, the average adjustment due to lifting that was made along the entire length of the subsidence-influenced railway was only 0.5 ft (152 mm)."

Jan 1, 2010

By David Newman

The latest version of the Surface Deformation Prediction Software (SDPS) package is presented through its application to a number of case studies. The package now exploits all the benefits of the Microsoft Windows platform and has a direct interface to CAD software, thus facilitating input and output. Also, the package features advanced calibration routines to handle predictions over specific regions. The case studies presented highlight the features and capabilities of the new package.

Jan 1, 2001

By B. (Mamas) Das

A project to evaluate the suitability of point Load strength tests for testing and classifying coal measure rocks for coal mining application was initiated by Canada Centre for Mineral and Energy Technology (CANMET). A summary of this study with emphasis on the important findings is presented in this paper. The instrument as used in this study is a Robertson Research Rock Strength Index Log. Because of the variation in the correlation ratio between uniaxial compressive strength and point Load strength index for hard rocks and soft rocks it was decided to establish this corre¬lation initially on cement concrete specimens specially prepared for this purpose following ASTM specifications. These specimens are expected to represent soft rocks and at the same time would be of uniform quality. Once a general trend of this correlation was established tests were performed on coal and rock samples from the sub-bituminous and bituminous coalfields in Canada. The most important results may be stated as follows: (i) Generally, the common value of the ratio between the uniaxial compressive strength and the point load strength index ranges between 8 to L4. (ii) The Robertson Research Rock Strength Index Log proves to be quite suitable for testing sandstone, siltstone and some coals from the bituminous coalfields but problems have been experienced when testing weathered samples or samples from the sub-bituminous coalfields. (iii) In some cases tests were successful if Larger samples from weathered zones or from sub-bituminous coalfields were used. However, a magnified load gauge for 0-3KN or 0-5KN is expected to be the best solution for soft and weathered rocks in most of the cases. Some mudstones and some rocks from weathered zone do not appear to be suitable for these tests. This aspect of the study is still under investigation. (iv) Deterioration of rock properties due to weathering has been determined through tests on samples collected from weathered and unweathered samples.

Jan 1, 1984

By Asmaa Yassien

Finite element models were developed to study the effect of tensioned and fully-grouted bolts on the stability of the mine opening in a three-entry development system using a typical geological column for the Pittsburgh Coal Seam. The models were used to study the effect of each bolt type on the stress distribution in the immediate roof, yield zone development and the vertical deformations. Comparison of all of those features show that the effect of a tensioned bolt on the stress distribution in the immediate roof is restricted to limited areas, whereas the fully-grouted bolt has a much wider effect on the stress distribution. Both types of bolts can reduce the yielding and deformation in the immediate roof to different degrees. The fully-grouted bolt reduces the sliding along the bedding plane more than the tensioned bolt. Both types of bolts were able to maintain the bedding planes without separation. The induced forces in both types of bolts are analyzed. A rapid increase in the shear force and bending moment occurred in the fully¬grouted bolt due to the relative motion of bedding planes.

Jan 1, 2002

By Axel Preusse

In the Ruhr district, pipelines of public and private infrastructure are made of cast iron, steel, plastics or asbestos cement. Legal framework, technical regulations and normative standards define which pipeline materials may be used for the transmission of which kind of product Thus ground water endangering substances as well as inflammable or explosive products are only permitted to be transported in steel-made pipelines. Ground movements, due to underground mining, are transmitted via the soil to the pipeline and cause extra strain within the steel pipeline (Figure I). In extreme cases durable deformations may occur, characterized by an oval profile or a fold in the pipeline. To avoid or minimize damages, balancing elements are installed into the concerning pipeline, reducing the ground movements which might otherwise cause damages. [ ] The distance between the balancing elements is not arranged by random, but by a calculation method developed in a doctoral thesis [Spielberg, 1999] which represents the actual available standards in science and technology. The calculation method considers all relevant influencing variables with impacts on the movement behaviour of steel pipelines in mining areas, such as technical data of pipeline design (e.g. steel grade, wall thickness, weld seam quality), soil conditions (e.g. friction), laying depths of the pipelines, the operational impacts (working pressure, corrosion) and the mining impacts. As of today, mining has caused no damages to steel pipelines protected by this calculation method.

Jan 1, 2004

By Abdolreza (Reza) Osouli

Determining the roof stability condition of underground coal mines in the Illinois Basin is sometimes very challenging. The roof stability of Illinois mines are mostly affected by two types of shales: Anna Shale and Energy Shale. These layers are sometimes weak in parallel bedding when subjected to horizontal stresses. The roof rocks in the Illinois Basin are are typically more moisture sensitive than the other coal fields. In this study the geotechnical properties of some of the shale units as well as limestone layers will be presented. The geotechnical properties of roof rocks consist of moisture content, unconfined compressive strength, slake durability, indirect tensile strength, and point load tests (Axial and Diametral). The correlation of indirect tensile strength versus diametral point load strength as well as unconfined compressive strength versus axial point load test are explored and discussed. These correlations will help in identifying the roof mass index and planning appropriate roof control measures. This study also evaluates the application of CMRR rock mass index for an Illinois coal mine.

Jan 1, 2014

By Anthony T. Iannacchione

Underground bituminous coal mining is a large and significant industry within the Commonwealth of Pennsylvania, and it has a legacy of environmental consequence. For example, in 2008, 13.5 acres (5.5 hectares) of land were undermined by longwall mining every day. Laws and regulations have been promulgated requiring companies involved in this industry to remedy mining damage caused to homes, businesses, and land; replace impaired water supplies; and repair impacts to streams and wetlands. The regulations and technical standards set by the Pennsylvania Department of Environmental Protection (PA DEP) have been put in place to assure that coal operations comply with ACT 54 of the Bituminous Mine Subsidence & Land Conservation Act and other related legislation. These regulations and standards require operations to address impacts when a mining permit is submitted and as permits are modified and extended. One of the special provisions of ACT 54 is the requirement by the PA DEP to produce an assessment of the surface impacts of mining every five years. The University of Pittsburgh was contracted by the PA DEP to perform the 3rd assessment, which spanned from August 21, 2003, to August 20, 2008. This paper details the findings related to surface structure undermined during this period. A total of 3,735 structures were tracked. Four-hundred-fiftysix reported effects were found, and each required additional information and analysis. The majority of the reported effects were associated with eight longwall mines. Characteristics of the structures were analyzed and discussed, with special attention to those with reported effects. The number of undamaged and reportedly damaged structures (i.e., dwelling, barn, commercial building, etc.) undermined during the assessment period were listed. Lastly, the resolution status and type of resolution were analyzed for all structure reported effects.

Jan 1, 2011

By Kevin Beauchamp

In many cases traditional support designs cover the many variations in ground conditions and bolt performance by a conservative factor of safety. The result is that most bolts are ineffectual most of the time and yet the response to occasional roof collapses is an even more conservative design. The probabilistic analysis presented in this paper takes several important parameters of a support design into account such as span, bolt strength, bolt length, water pressure, seismic accelerations, joint orientation, bed thickness and joint strength and allows the effect of variations in these parameters to be evaluated simultaneously. The analysis demonstrates the application of the probabilistic approach to both blocky, wedge-dominated conditions and bedded deposits dominated by laminations. All mine excavations have a designed stand-up time. By taking into account of the possible variations in the design parameters explicitly, it is possible to produce a support system designed to ensure stability over a given period of time. Rather than use a factor of safety criterion, the approach uses a percentage reliability or probability of failure. By understanding the probability of failure of the support system, it is possible to improve the performance of ground support without any increase in cost or conversely to decrease the cost while maintaining the performance of ground support. This approach reduces reliance on empirical experience and leads to a better understanding of the key factors that influence stability and can provide a much more accurate and optimized assessment of support design and performance. The result is a more cost-effective support system and we hope that a broader application of this approach to ground support in underground mines will lead to a greater acceptance in the industry of probabilistic analyses and of terms such as Probability of Failure and Reliability of Support.

Jan 1, 2003

By Madan M. Singh

Mining under bodies of water such as oceans, lakes, rivers, streams, ponds, and other impoundments, is not a new technique. However, in the United States it has been fairly restricted to date. In order to recover the maximum amount of the nation's reserves, in the future, it is important that further mining under such bodies of water be planned. However, it is imperative that this is not done at the expense of danger to the nation's miners or appreciable property damage. If all the bodies of water are considered large, and it is assumed that these constitute a hazard when mining in their vicinity irrespective of their size and geometry, a significant percentage of the coal reserves are likely to be sterilized. How- ever, by adopting special mining plans and procedures, it may be possible to release reserves for exploitation that would otherwise be unmineable since the surface of bodies of water below which they lie are relatively small in size. In 1977, the Bureau of Mines issued Information Circular (IC) 8741, entitled "Results of Research to Develop Guidelines for Mining Near Surface and Underground Bodies of Water". This document was based on the work done by Skelly and Loy (under Contract No. H0252083) and K. Wardell and Partners (under Contract No. H0252021). How ever, these guidelines have limited application, because these did not (1) define the bodies of water of concern, and (2) take into account the nature of the strata being encountered. These guidelines assumed that all bodies of water which would be undermined were large. For the purposes of this discussion, water bodies may be divided into three categories, depending upon their potential to cause damage to the underlying mining activity: ? catastrophic ? major ? limited Bodies of water which pose the threat of catastrophic destruction in the mine, should there be an inrush, include oceans, large lakes, big inland reservoirs, and rivers that could flood the mine complete- ly in a short period. Those with major potential for damage would include lakes and streams which might present a danger to both life and property if not considered in the mining plans. Finite bodies of water which have a volume considerably smaller than the mine volume offer a limited potential for damage in the case of an inrush. These include flowing streams which have a relatively small rate of replenishment and which can be dealt with by pumping or isolation in the event of a breakthrough into the mine. Such bodies of water may be inconvenient and cause a temporary disruption of production, and could even cause some damage to equipment, but only in rare instances would personal injuries occur. The scope of this paper is limited to the exploitation of stratified mineral deposits with overlying -face bodies of water. Vein and dessiminate ore deposits are not discussed, nor are breakthroughs into adjacent mines in the same horizon. Overlying, water-logged strata also pose a serious threat to mining, but are not treated in this discussion. Pending further investigation these strata may be considered as bodies of water with catastrophic potential for damage, with the base of the strata being considered the bottom of the water body. When the body of water is large, so that it may cause catastrophic damage to the mine in the event of an inrush, the guidelines suggested in IC 8741 are applicable. In order to develop criteria and procedures for mining under smaller bodies of water, however, it is necessary that the nature of the strata disturbance due to underground mining be examined.

Jan 1, 1981

By John Latilla

Following its introduction on underground collieries, the mandatory Code of Practice to Combat Rockfall Accidents (CoP) was applied to all opencast operations of lngwe Collieries (the South African division of BHP Billiton Energy Coal). The CoP includes, but is not limited to, requirements to assess hazards, manage them and monitor compliance. Information on methods to measure highwall conditions and compliance with control measures on opencast strip mines, as opposed to open pit mines, was found to be anything but freely available. However, on the Ingwe underground mines, a system of rating physical conditions in each section and how well production personnel were managing the situation, has been used with success for some time. It was decided that a similar approach would be taken, and, as with the underground rating system, the resultant rating forms should not be aimed at rock engineering specialists only but should be able to be used by production personnel as well. This paper discusses the highwall risk rating method as evolved over a couple of years and highlights that it is a flexible tool that can easily be changed to suit an individual mine's requirements. It also shows how operational aspects are being measured to determine how well the identified hazards are being managed. Allied to the method is a relatively easy, and certainly "low capex," mapping technique which allows between 500 and 1000m of highwall to be covered in a day. Features generally recorded include lithology, bench height, work still to be completed, coal losses or "toes", presence of water, dolerite intrusions, existing and potential failures, prominent joints, declared special and cautionary areas, cracks on upper benches and condition of spoil piles. Highwall mapping and photography as well as basic geological data collection, enable highwall risk and operational ratings to be determined. The same rating sheets may also be completed by production personnel, but without detailed mapping.

Jan 1, 2002

By André Zingano

Pillar collapses have been studied for several years and can be classified into two types: nonviolent squeeze or violent pillar collapse, i.e., controlled or uncontrolled pillar collapse. Underground coal mines in Brazil are considered shallow mines, because the overburden thickness varies between 20 and 400 meters. For this reason, the coal pillars should be designed as permanent pillars to avoid subsidence and groundwater problems. In the last two years, various pillar collapses occurred, one being a violent collapse and the others being squeeze collapses. All these collapses were considered massive pillar collapses because many pillars were involved. In the violent pillar collapse case, the width¬to-height (w/h) ratio was less than three; although, the pillar safety factor (SF) was more than 1.3. There was a collapse of about 100 pillars in less than three hours. The objective of this study is to determine the mechanism of pillar collapse for this violent pillar collapse. Convergence monitoring and numerical modeling were applied to combine field data and theory to simulate the pillar collapse. Convergence field measurements introduce the arc-effect behavior for the roof. The results showed that other factors besides pillar geometry caused the pillar failure. Other parameters, mainly dip of the coal seam and presence of fractures and faults may affect the strength and failure mechanism of a pillar.

Jan 1, 2004

By M. Karmis

mining factors and representative ground movement parameters. Based on this analysis, the previously developed prediction methods were modified and tested for their applicability in the Appalachian coalfield. Finally, in order to facilitate the implementation of the prediction methods, as well as the data processing of the monitoring program, a number of computer software were developed and will be discussed in the paper. Surface deformations above underground mines and their prediction and control have been the topics of an extensive research effort by Virginia Polytechnic Institute and State University over the past few years. During the initial stages of this research, a number of case studies were collected from the literature, the mining industry and various government and state agencies and, based on the analysis of this information, appropriate prediction methods were proposed (Goodman, 1980; Webb, 1982; Hasenfus, 1984; Karmis et al., 1984). Although the prediction methods were based on sound concepts, it became evident that their accuracy and implementation were a reflection of the size and quality of the collected case studies. In this respect, the data bank was rather insufficient and posed certain questions regarding the development of subsidence information due to inappropriate length and spacing of monuments used in subsidence surveys, density and accuracy of such surveys, lack of monitoring horizontal movements, etc. In an effort to alleviate these problems, a comprehensive monitoring program was initiated in the coal mines of southwest Virginia, which included: - Two longwall and five room and pillar mines. - In total, seven longwall and sixteen room and pillar panels. - Monitoring lines in excess of 35,000 feet. - Vertical as well as horizontal measurements. A high accuracy digital computer tacheometer was used in all surveys and the type and spacing of all monuments were in accordance with well accepted guidelines. The data from this monitoring program completed the initially collected data bank and, thus, enabled a much needed statistical analysis between

Jan 1, 1987

By Amirhossein Molavi Tabrizi

In this paper we introduce a realistic model for mine openings that explicitly considers the effects of local irregular topography. Also, we consider the effect of entry orientation and rock anisotropy on the induced stress fields around mine openings under the given in-situ stress field. A triangular mesh formulation is derived for representing complicated irregular surface topography and underground openings. Each element contains three internal collocation nodes. Parts of the surface which are far from the mine openings are discretized by infinite elements. The rectangular infinite elements with three internal nodes are introduced specifically for this problem so they are compatible with the triangular elements. With the corresponding boundary element method (BEM) formulation, we then investigate the combined effect of the topography and entry orientation on the stress fields induced by openings in anisotropic rocks under in-situ stresses. A single rectangular opening in the anisotropic ground with topography and in-situ stresses is simulated using data from the Carroll Hollow mine in Ohio. The results of these simulations show that topography, rock anisotropy, orientation of the regional stress field and mine opening geometry all have appreciable effects on the stress fields around underground openings, yet these factors can all be accounted for in an efficient code with no need to discretize the model domain. Future applications using this new BEM formulation will provide useful guidance on selecting the optimal opening orientation in the mine in order to minimize undesirable stress concentrations around underground mine workings.

Jan 1, 2014

By D. L. Price

This paper presents a method of measuring field power consumption of shearers and deriving specific energy consumption versus shearer haulage speed performance curves. A description of a computer program which simulates the cutting action of a shearer drum is presented. A comparison between the field specific energy curves and the computer simulation results is made. The simulation results compare well with the field data where all the coal seam is being cut by the shearer. The computer simulation results give hack-calculated field pick force cutting characteristics, which allow the performance of the shearer to be predicted for other operating conditions, e.g. effect of changes to pick lacing, effect of changing the drum rotational speed, allows the calculation of power requirements for a particular production rate.

Jan 1, 1992

By Clarence O. Babcock

Since Vicat in 1833, the width to height ratio of a mine pillar has been taken as the fundamental variable in pillar design. From work in the laboratory by many investigators testing rock, Coal and concrete samples, it has been concluded by some that pillars with a width to height ratio of 10 to 1 are indestructible. It has also been concluded that a constrained core exists within the pillar which increases the pillar strength. The role of the roof and floor, if mentioned at all, is often noted in an incidental way. In the present work on laboratory testing of model pillars on concrete, coal, and rock instrumented with special strain gages, it was concluded that the end constraint and not the width to height ratio is the significant variable in determining the pillar strength. In tests where the end constraint is steel, a large compressive stress is produced on the horizontal plane of the pillar, and this effect increases as the width to height ratio is increased, resulting in an increase in pillar strength. If the end constraint is not steel but something with a small Young's modulus, the state of stress in the horizontal plane may be tensile, increasing as the width to height ratio increases, resulting in a decrease in pillar strength. Related to mining, the results are that a large width to height ratio pillar is strong for strong roof and floor and weak for weak roof and floor. That is, the roof and floor and not the width to height ratio determine the pillar strength. The confined core condition should be verified by testing if large pillars are to be used. If there is no confined core or the pillar is in tension, smaller pillar sizes should be used. The final conclusion is that the geometry alone is meaningless in pillar design.

Jan 1, 1984

By K. Biswas

So far, all pillar design methods or approaches consider the coal seam as a uniform structure From some mine visits in northern Appalachian Region. it is found that some coal seams have binder or parting material within the coal scan with varying thicknesses and numbers- And it has also been found that these kinds of hinder materials tire prone to weathering when exposed to ambient mine moisture In this paper an attempt has been made to study the weathering susceptibility of parting materials and coal when exposed to moisture and a two dimensional finite element analysis has been carried out to study the effect of the presence of partings on the structural integrity of the coal pillar in terms of short-term and long-term stability.

Jan 1, 1995

By Jeffrey K. Whyatt

Estimation of the initial vertical stress carried in a coal seam is an important first step in virtually all methods of evaluating the required size of pillars in coal mines. Such estimates are a trivial exercise in coal fields overlain by gently undulating topography. The LaModel program is easily and routinely applied in such cases to efficiently estimate mining-induced stresses throughout the coal seam. However, application of LaModel to coal mines operating under rugged topography and/or in tectonically disturbed regions is more difficult. LaModel estimates stresses in a twostep process. Topographic and multi-seam mining effects on insitu stresses are estimated in an initial step, and then mininginduced stresses are estimated in an independent second step. A LaModel program function has recently been introduced that decouples these two steps, allowing in-situ stresses to be directly entered from a file rather than calculated. One application of this function is to streamline sensitivity studies by avoiding repeated recalculation of in-situ stress. The function also allows importation of in-situ stress estimates developed by other means. There are no constraints on the imported stress field, which may include significant stress perturbations due to topography, faults, etc. Hence, the range of geologic environments that can be examined by LaModel is significantly increased. This study uses the new decoupling function in an exploration of in-situ stress estimation in mountainous terrain. One option is to use the topographic stress estimation feature included within the LaModel program, and the influence of important parameters in this routine is explored. Another option explored is importation of results from a detailed volume element model. Results of this study suggest that the method used to estimate in-situ stress, and the details of its execution, can have a significant impact for mines in mountainous terrain with strong overburden. More generally, decoupling is an efficient and flexible function that should be considered for most design studies.

Jan 1, 2011

By Frank E. Chase

A massive pillar collapse occurs when undersized pillars fail and rapidly shed their load to adjacent pillars which in turn fail. This chain reaction-like failure may involve hundreds, even thousands, of pillars and the consequences have been catastrophic. One effect of a massive pillar collapse can be a powerful, destructive, and a potentially hazardous airblast. On eleven recent occasions, massive pillar collapses have occurred in six southern West Virginia coal mines. Two other instances of massive pillar collapses in U.S. mines have been documented in the literature. Research was conducted at four mines where massive pillar collapses occurred. Geotechnical evaluations of roof rock, coalbed, and floor conditions were made. Evidence indicates that in each case a massive and competent roof rock unit was able to bridge a relatively wide span, creating a pressure arch. Eventually, the pressure arch apparently broke down, and the structural characteristics of the pillar system were such that sudden, massive pillar failures occurred. Data collected at the failure sites also indicates that all the massive collapses occurred where the pillars width-to-height ratio was 3.0 or less. Numerical modeling, performed with a modified version of the MULSIM/NL computer program, supports the conclusions that the extent of the mined-out area, the bridging capability of the main roof, and the width-to-height ratio of the pillars are probably all significant factors in the occurrence of massive pillar failures.

Jan 1, 1994

By Morgan Sears

The LaModel program (Heasley, 1998) is a displacement discontinuity, boundary element model (BEM) for analyzing stresses and displacements in single and multiple-seam coal mines. After the Crandall Canyon mine collapse, the need for better design guidelines for LaModel was observed and a new calibration method for deep cover pillar retreat was developed (Heasley et al., 2010). However, the scope of this initial calibration was limited to single-seam mines deeper than 750 ft. This limited application of the initial calibration method lead directly to the research presented in this paper, which attempts to define appropriate LaModel calibration guidelines for pillar design where shallow cover and/ or multiple-seam mining scenarios are encountered. As part of this research, a database of shallow cover case histories has been developed, and this database is used to help validate the shallow cover calibration method. By adding the shallow cover database to the previous deep cover database, the LaModel calibration method has now been extended to the complete range of mining depths, as well as to multiple-seam cases. With this shallow cover calibration, the utility of the LaModel program continues to increase.

Jan 1, 2013