Search Documents

By H. Soto, J. Jara, F. Nava, J. B. Hiskey, B. J. Scheiner

Laboratory tests showed that ozone can destroy free cyanide and weakly complexed cyanide (copper and zinc cyanides). The iron cyanide complexes were resilient to ozonation but they were effectively eliminated by precipitation with Fe (II) ions under controlled pH conditions. Tests carried out with effluents from a number of gold mills confirmed the results obtained previously in the laboratory. The industrial samples contained cyanide in the form of free cyanide and also complex copper, zinc and iron cyanides. Solutions that contained up to 184 mg/L total cyanide, after the ozone treatment analyzed only 2-3 mg/L dissociable cyanide and 50-90 mg/L CN(t) (accounted for by iron complexes). After precipitation with ferrous ions total cyanide was reduced below 1.5 mg/L. For most solutions ozone consumption ranges from 3 to 6 g per g of cyanide destroyed. However, certain impurities (such as SCN and S203 ), present in some effluents, increase ozone consumption and make it more difficult to reduce copper concentration to satisfactory levels.

Jan 1, 1993

By Thys B. Johnson

This paper presents a new algorithm for solving the Controlled Flow Mine Ventilation Problem in an optimal manner - minimum power consumption. The use of booster fans and restrictions on the locations of ventilation regulators are dealt with in a straightforward manner. This new approach is based on a common Operations Research algorithm for which there are many fast computer programs available.

Jan 1, 1982

By Joseph B. Alberts, David D. DiPonio, Francis B. Manning

From 1996 to 2001, Wayne County and 13 suburban Detroit communities constructed the Downriver Regional Storage and Transport System (DRSTS) to improve area water quality, protect public health and alleviate basement flooding. The project consisted of a 10-mile long storage and transport tunnel, a pump station at the existing wastewater treatment plant, 9 miles of relief sewers (6 in tunnel and 3 in open cut). The work was separated into 10 contracts. Due to hydraulic design requirements and other constraints, the tunnel profile was located generally 65 feet below ground surface within a soft to medium clay strata which skimmed along the top of a very dense glacial till “hardpan” overlaying bedrock. Boulders within the tunnel bore were recognized as a significant, but indeterminate risk. This paper presents a case history of the owner’s contracting strategy for risk assumption and management of the boulder impacts on the project. Actual conditions encountered during construction and contractual adjustments made to address problems are reviewed, and recommendations for future contracts are included.

Jan 1, 2003

By A. M. Marabini, V. Alesse, Belardi. G.

An alternative flowsheet was designed for the flotation treatment of a complex sulfide ore from the Sotiel Mine in Spain. The ore contains 0.71% Cu, 2.24% Pb and 5.63% Zn. Two specially developed synthetic collectors, methyl-mercapto-benzoxazole (MMBO) and 6n-propoxy-mercapto-benzo-thiazole (PMBT), were examined. MMBO exerts a specific action on copper and zinc minerals after treatment with copper sulfate, and PMBT exerts a specific action on Pb minerals. Flotation operating variables (pH, frother type, frother quantity and feed particle size) were examined by means of rougher flotation tests to determine the optimum conditions for the new collectors. Once the optimum conditions were determined, a series of open flotation circuits were run on feeds of various particle sizes (obtained by different types of grinding). The objective was to obtain high-grade Cu and Zn concentrates. The results of the open-circuit tests demonstrated that a Cu concentrate grading from 18% to 23% Cu and a Zn concentrate grading from 40% to 48% Zn can be produced.

Jan 1, 1996

By Monica Pavlik, Thomas Wildeman

Water from the Forest Queen mine adit near Silverton, Colorado drains into a natural wetland. Because the pH of the water averages 5 and the iron concentration averages 18 mg/L, it was thought that the wetland might naturally treat the water. Of most concern with respect to the aquatic environment is zinc whose concentration averages 0.60 mg/L. Starting in October 1997, the surface waters, ground waters in the peat substrate, and the sediments in the wetland were sampled and analyzed four times over the course of four months. The adit water primarily remains as surface water where Fe, minor amounts of Al, and no Zn are removed. After the adit water enters the peat, then it is found that the pH rises to 5.8-6.5 and sulfate is reduced. The removal of Zn and A1 is caused by these two changes. However, Fe in its reduced state is quite soluble and may be remobilized in the reduced environment of the peat.

Jan 1, 2000

In conjunction with steady increases in production levels, longwall operators have applied greater quantities of ventilating air and spray water in an effort to control respirable dust and/or methane. Air velocities greater than 7.6 m/s (1,500 )fpm) have been measured on longwall faces. Operators have expressed concern over the potential entrainment of respirable dust at these high velocities. The greatest likelihood for entraining dust into the high-velocity airstream may occur as shields are advanced, allowing relatively dry particles to fall from the shield canopy directly into the airstream. Laboratory tests to simulate dust liberation during shield movement were conducted at the Pittsburgh Research Laboratory of NIOSH at velocities ranging from 2.0 to 8.2 m/s (400 to 1,600 fpm). Airborne dust samples were obtained with personal impactors to quantify the size distribution and concentration of the dust entrained at the various air velocities. Statistically significant increases in both total and respirable dust concentrations were measured as test air velocities were increased.

Jan 1, 2002

By S. Majumder

The longwall face supports are provided to prevent the caving of the immediate roof at the working face. The thickmess of the immediate roof may be obtained from the working height and the average bulking factor. A strong bed, capable of withstanding maximum bending moment among the beds within the above roof, can be identified. The load on the strong bed may be obtained by finding out the overlying beds that will rest on the former during sagging. The limiting span, L, for this unsupported loaded bed, as a beam with built-in ends, can be calculated. The support density required at the supported span (face to goaf edge), a, during the first fall, is now estimated with a view to have a safety factor 2 at the face end, when bending failure occurs at the barrier end. However, the above value is inadequate to provide necessary safety margin against bending failure at the face end, during the subsequent cavings as cantilever, for L/a less than 20.6. d For the latter case a separate expression is derived.

Jan 1, 1986

By Ronald E. Feltman

Most engineering firms engaged in the design and manufacture of milling components and systems have established, through the years, a relatively well defined system design procedure. The process design engineer has at his disposal several alternative approaches to the successful completion of this task. Unfortunately, while these alternatives, at first glance, appear to be rather straight Forward, any attempt to implement them into a fully integrated commuter design program becomes increasingly more complex when one addresses himself to the problem in total. This paper summarizes Kennedy Van Saun's approach to the solution of this problem through a planned system design. Following the problem definition and discussion, a detailed analysis and system design synthesis is presented; the major aim here being to provide a system design which may be programmed and run on a relatively inexpensive computer installation such as the IBM 1130 system currently in use at Kennedy Van Saun. A summary section is also included, which Provides a general outline guide to the program systems design of equipment which, while quite different from milling system functionally, nevertheless lends itself to the approach used in this paper.

Jan 1, 1969

By Satya Harpalani, Xue Zhao

This paper discusses the results of an experimental investigation to study the release of methane in coalbeds. Absolute porosity of coal samples was first determined experimentally. Following the porosity measurement, adsorption/ desorption tests were carried out to determine the gas content of coal and the rate at which it is released. Finally, micrographs were obtained using electron microscopy and the use of a physical model, developed to explain the gas flow behavior of coal, was justified. The results of this study indicated that the measured absolute porosity of the coal sample was between 5 an 6%. This was significantly lower than the porosity estimated by comparing the micrograph area occupied by the pores and the area of observation for several micrographs, suggesting that coal has a large number of pores with a very small volume. The micrographs also clearly indicated that coal has a large interconnected network of cleats and microfractures. The adsorption/desorption experiments showed a hysteresis between the adsorption and desorption isotherms. Also, the rate of desorption was found to be strongly dependent on the particle size of the specimen.

Jan 1, 1989

By J. D. Goodrich

Success of The Carter Mining Company's safety program can be primarily attributed to "total immersion" of all operating and staff personnel in program design and implementation. Currently, the Company operates two surface coal mines in Campbell County, Wyoming. Total employment is about 440 and current annual production is about 15 million tons. The safety program has evolved from one which was administered primarily by staff personnel (the Safety Department) to one which requires active participation by line management and operating personnel. Lost time accident frequencies have declined from a high of 1.86 per 200K hours worked in 1978 to zero in 1982. Reportable accident frequencies have declined from slightly over 5 to slightly over 2 during the same period. Analysis of program results indicates that the most important achievement by the company has been to gain strong commitment to safe operation by all employees. It is important that program format and content be frequently changed and modified so that: 1) The requirement for safe job performance is communicated well and often, 2) The safe job performance message is trans- mitted in new and interesting ways, and 3) Operating personnel participate in design and implementation of the program.

Jan 1, 1983

By Arland R. Krueger

You have asked me today to tell you how quarried stone is meeting the challenges of contemporary architecture. The new position of stone, the oldest building material, in contemporary architecture, was described to me very concisely the other day by a very distinguished avant garde architect. He said rather wryly, "Do you know, if quarried stone had only just been discovered, we would all be calling it the most miraculous of all the modern miracle building materials." His prognosis was, I believe, much more than a witty quote. It echoes the surprise and. enthusiasm with which a considerable segment of the architectural profession is rediscovering stone as a most modern building material that offers unsurpassed values in beauty and practicality - well deserving of the term "miracle".

Jan 1, 1960

By S. K. Kawatra, H. J. Haselhuhn

"Fine-grained hematite ore can be concentrated by the process of selective flocculation and dispersion, which relies on proper reagent selection and control of water chemistry. While many previous studies have been performed analyzing the effects of different reagents on this process in a laboratory environment, this paper focuses on investigating the water chemistry within the process in a pilot-scale continuous deslime thickener.The pH, sodium concentration, calcium concentration and magnesium concentration were varied to determine their effects on the iron concentrate grade and recovery, and the phosphorus concentrate grade and rejection in the pilotscale selective deslime thickener. The ideal pH for the iron grade and recovery of the process using a starch selective flocculant was found to be 10.5. Phosphorus rejection, however, was increased at lower pH values. Minimization of sodium concentration was shown to improve iron grade, iron recovery and phosphorus rejection. Calcium acted as a nonselective flocculant showing higher iron recovery, lower iron grade and lower phosphorus rejection with increasing concentration. Conclusions could not be drawn from the experiments that varied magnesium concentration.The zeta potential of the solid-liquid interface of particles in each sample taken was also analyzed to show relationships between zeta potential and process performance. In all cases, a maximization of the magnitude of zeta potential correlated with increased iron grade and recovery. This supports the hypothesis that a higher level of dispersion enhances the selective flocculation and separation process.IntroductionThe United States produced 53.2 million metric tons out of the 3,000 million metric tons of concentrated iron ore produced worldwide in 2012 (Tuck, 2013). With this in mind, there has been a large increase in iron ore processing research (Bolen, 2014; Carlson and Kawatra, 2008, 2013; Halt and Kawatra, 2014; Halt et al., 2014; Haselhuhn et al., 2012a,b, 2013a,b; Liu et al., 2014; Manouchehri, 2014; Sandvik and Larsen, 2014; Semberg et al., 2014). Of the 53.2 million metric tons produced, roughly 8 million metric tons of hematite (Fe2O3) concentrate were produced using a process known as selective flocculation and dispersion (Cliffs Natural Resources, 2011). This process is the only economically viable method for concentrating low grade (< 40% Fe) fine grain (< 25µm liberation size) hematite ores. It is scarcely used due to difficulty in controlling the surface chemistry of the ore and high reagent costs (Department of Energy, 2001; Haselhuhn et al., 2013a). The process is highly dependent upon both reagent selection and precise control of the water chemistry during separation. This study shows the dependence of the process performance of a pilot-scale deslime thickener on the water chemistry in the feed slurry."

Jan 1, 2015

By Y. Guan

The dissolution behavior of silver and copper from silver/copper alloys in ammoniacal solutions has been investigated using a rotating disc. Oxygen was used as an oxidant. The effect of composition of alloys, concentration of lixiviants, stirring speed and temperature on the overall dissolution kinetics has been studied. Silver / copper alloys of three compositions were used in this study. The atomic percents of silver in these alloys were 76.9, 46.9 and 24.1. The results on the rate of dissolution obtained for these alloys have been compared with that of pure silver and copper under the same testing conditions. A particular emphasis has been given to the galvanic effect on the overall dissolution rates.

Jan 1, 1993

By D. V. Professor Keller

The production of premium coal-based fuels (<3% ash) and ultra clean coals (<1% ash) using the process of selective agglomeration requires proper selection of raw coal, rough preparation procedures, milling equipment, product coal size distribution, water purity, agglomerants, agglomeration equipment and operational procedures. Each of the variables can contribute a small fraction to the impurity load in the product coal or limit the ability of the process to separate mineral matter-free coal. Each of the variables and their importance will be examined from data produced at the bench by batch and continuous agglomeratons as well as the results from pilot plant and tonnage production units. The results are discussed which have indicated that some standard commercial coals can be produced with ash contents as low as 0.2 % ash (batch/bench) and several tonnage lots of 0.6% ash in as 200 lb/hr pilot plant. In most cases iron pyrite released from the coal matrix and with proper pH control is rejected from the product coal agglomerates.

Jan 1, 1995

By C. Tom Blevins

LADIES AND GENTLEMEN : This presentation is to discuss production and roof control problems associated with directional lateral stresses in an in situ stress field and the approach that Inland Steel Coal Company made in trying to cope with them. Before proceeding, a brief description of the mine location, product, geology, restraints, and mine history is in order.

Jan 1, 1982

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

GENERAL HYDROLOGIC REGIME The total hydrologic cycle must be considered when evaluating potential ground water problems in a mining environment. Precipitation is the ul¬timate source of all surface water and essentially all ground water. Stream flow during low flow periods often orig¬inates as seeps or stream gains (base flow) where the water table intersects the land surface. A stream that is higher in elevation than the ground water system may lose flow, thereby recharging the ground water system. The magnitude of stream gain or loss is dependent upon the hydraulic conductiv¬ity and related properties of the underlying hydrostratigraphic units. Ground water moves constantly from recharge areas to discharge areas (streams and springs) usually at very slow rates. Large quantities of ground water may be in¬tercepted in many underground mining environ¬ments. Construction of an underground mine in saturated formations may encounter ground water inflows ranging from very small to very large and from continuous to intermittent depending upon the hydraulic properties of the hydrostratigraphic units penetrated. SURFACE WATER VARIABLES Precipitation occurs in different forms, varying amounts, and with a wide assortment of temporal and areal distributions in the various mining dis¬tricts within the United States. Mine inflow can be affected in a matter of hours by precipitation events where there is a direct hydraulic interconnection between the mine and the surface through fractures or a mine opening. The timing, form, amount, and distribution of precipitation should be evaluated in a mine inflow study. A portion of the precipitation that falls in a topographic basin moves as sheet flow to runoff channels (Fig. 1). Some of the precipitation infil¬trates the unsaturated soil zone where it can either move laterally as interflow to the surface system to augment stream flow or move downward as re¬-charge to the ground water system. The unsatu¬rated zone (called the zone of aeration or vadose zone) can range in thickness from essentially zero to a few hundred feet. The saturated zone or ground water system occurs below the water table (zone where hydrostatic pressure is greater than atmos¬pheric pressure) where all the pores are filled with water (Freeze and Cherry, 1979, p. 44). Moisture can be lost from any of the systems (surface water system, unsaturated zone, and ground water sys¬tem) by the processes of evaporation and transpir¬ation which return moisture to the atmosphere. Stream flow consists of runoff and interflow components plus an additional base flow compo¬nent (Fig. 2). Base flow constitutes ground water discharge to a stream. Base flow plays an increas¬ingly significant role as total stream flow declines. Base flow is important because it constitutes much if not all stream flow between periods of precipi¬tation when runoff and interflow have largely dis¬sipated. INTERACTION OF SURFACE WATER AND GROUND WATER SYSTEMS Recharge from a surface water system to ground water systems can occur via unsaturated or saturated flow. The amount of recharge is depen¬dent primarily upon the vertical hydraulic conduc¬tivity of the formations underlying the stream and the availability of water. Streams that flow over low hydraulic conductivity formations lose little water even if the ground water levels are significantly lower than the stream. A ground water system may contribute flow to a surface water system but nor¬mally only by saturated flow. This contribution usually takes the form of seeps, springs, and the base flow of streams. GROUND WATER VARIABLES Introduction The variables that affect ground water flow are discussed in increasingly complex theoretical situ-

Jan 1, 1986

By Louis W. Cope

In the early 1900s, vat leaching was a common process for treating gold ores. It was, however, labor intensive and was abandoned in the 1930s. Technology advances in recent years, though, have caused vat leaching to once again become a viable alternative in precious metal processing. At least three plants have been built. Others are being considered as alternatives to agitation and heap leaching. What is vat leaching? Vat leaching is a process in which ore is crushed and screened to a size of between 6 to 12 mm ( 0.25 to 0.5 in.) This crushed ore is placed in a large, boxlike container where an alkaline-cyanide solution is added and later removed. The process might be likened to indoor, controlled heap leaching. The ore does not require fine grinding in a ball mill. Therefore, capital and operating costs are lower than agitation treatment. But the extra handling causes costs to be slightly higher than heap leaching. If any amount of fines is present, the ore should be agglomerated.

Jan 1, 1991

By Chris Crowl

Employee involvement does not directly correlate to performance improvement. A key ingredient is the introduction of new Human Resource Systems that promote both performance improvement and employee involvement. Many organizations have tried to use employee involvement as the &apos;&apos;fixer" of performance issues-and seen their performance deteriorate further. They failed to realize that the entire human resource strategy must be connected to the goals of performance improvement and that greater employee involvement is only one tool in that strategy. So what are Human Resource Systems? These are systems that all managers use to get work done. Most of us are familiar with basics such as planning, assigning work, checking progress (auditing), completing assignments. We also commonly think in terms of staffing, training, compensation, or corrective action. All of these are human resource systems. All must be designed to support what you are trying to accomplish with your people. We call that the Human Resource Strategy. Let&apos;s examine one part of a total strategy intended to support more employee involvement at Kennecott Utah Copper-the hourly job structure. The design of hourly jobs directly affects how many employees of different capabilities are required to get the work done. It begins to answer some fundamental questions: • What are the roles and accountabilities of each employee? Do they have enough information to make decisions, to take responsibility for their work?

Jan 1, 2004

By Colin Connors

Cemented rockfill is a key component in the success of underground mining at the Jerritt Canyon Joint Venture. The Murray and SSX mines are characterized by relatively poor rock mass quality, and the goal of complete mining recovery makes maintaining a high quality backfill product vital to the safety and efficiency of the mining operations. A large portion of the ore production from the Murray mine originates from drifting under backfill. Modelling studies performed to investigate induced loading of the backfill were used to develop engineering specifications for the backfill material. Operations history has shown an almost 100 percent stability of the backfill when mining is carried out beneath it. The volume of backfill required each year (approximately 300,000 tons) and the required cement content have a significant impact on the total mining costs. The potential for cost savings associated with higher replacement of cement with Type "C" fly ash and the implementation of a backfill strength management strategy were therefore evaluated.

Jan 1, 2001

By W. J. Garmoe

The Carr Fork mine is located approximately 50 kilometers southwest of Salt Lake City, Utah, in the Bingham or West Mountain District, adjacent to the Bingham open pit copper mine. Applied geology at Carr Fork, by Anaconda Minerals Company personnel, includes detailed geologic mapping and sampling of underground workings, logging and sampling of drill core and cuttings, and the preparation and posting of geologic maps and cross sections for geologic interpretation, ore reserve calculation, mine operations, and long range planning. Accurate and easily understood graphic recording of Carr Fork geology is essential for optimum use by operating and engineering personnel. The design and implementation of exploration, development and definition drilling programs, research into geological spatial relationships, and analysis of structural complexities of the Carr Fork deposit are also integral parts of the applied geology program.

Jan 1, 1992