Search Documents

By C. Garcia, C. L. Lin

Characterization and analysis of multiphase particles and/or particulate systems (such as the packed particle bed) are of great technological importance for mineral processing applications. In general the performance of these applications depends on the statistical characteristics of particle microstructures, such as composition distribution, surface exposure of mineral grains, pore network structure, etc. For continued technological progress in the field of multiphase particulate processes, the need for quantitative spatial analysis of multiphase particles in three dimensions has increased sign6cantly. Such quantitative information must be accurate enough that the measured values can be used as parameters for simulation models, process design procedures, and control strategies. Modern 3D image-acquisition techniques, such as X-ray microtomography (XMT), offer a unique imaging capability that can produce high-resolution (a few micrometers) three-dimensional images of the internal structure of multiphase particulate samples. These three-dimensional image data present new challenges for image analysis, image processing, and visualization. Furthermore, important issues should focus on how to use the 3D information and derive new insights into the improvement, design, and operation of mineral processing processes. In this paper, utilization of XMT for characterization and analysis of leaching process involving multiphase particulate system is discussed.

Jan 1, 2005

By Robert G. Moorhead

Fine-coal screening can be one of the most critical operations in a modern coal-cleaning plant. The yield and quality of clean coal produced in fine-coal circuits is controlled as much by how efficiently 0.15 mm (100 mesh) particles are sized as on the performance traits of the fine-coal cleaning device itself. In addition, the increased interest in effective fine-coal sizing operations indicates that many operators have also discovered its importance in affecting the quality and yield of clean coal produced in fine-coal circuits. This paper describes the three most prevalently used fine-coal screening technologies and discusses their sizing mechanism, performance, and application.

Jan 1, 1988

By Ebelia Manda, Peter RK Chileshe, Sydney Chinyanta, Abdul Samson, Victor Mwango Bowa

Buttressing is a widely employed control measure for mitigating slope failure in various settings such as openpit mines, road sections, dams, and hilly or rocky terrains. This paper presents a study on the effects of buttressing, specifically concerning slide-head toppling failure. Drawing insights from a case study of slide-head toppling in Zambia, our investigation employs both analytical (limit equilibrium) and numerical (3DEC software) modeling techniques. The analytical and numerical models exhibit notable similarities in their schematics and overall results, revealing a subtle effect of buttressing in controlling slide-head toppling failure. This study contributes valuable insights into the nuanced role of buttressing in slope stability, with implications for optimizing buttress design parameters. While the overall findings suggest a modest influence of buttressing on slide-head toppling failure, further discussions delve into the specific implications and potential refinements for practical applications.

Jan 1, 2025

By F. Rosenblum, P. Cancilla

The manual moisture determination methods employed today by mineral processing plants falls short in providing timely information required for automatic control. The costs associated with transporting and handling concentrates still represent a major portion of the overall treatment price. When considering the cash flow of a mining operation, that is governed by both the smelter contract, with moisture penalties and the quantity and quality of the concentrates shipped, an efficient method of on-line moisture content would be a welcome tool. A novel on-line determination system for ore concentrate moisture content would replace the normally tedious classic manual procedure. Since the introduction of microelectronic¬based control systems, operators have strived to reduce the treatment costs to the minimum therefore a representative and timely determination of on-line moisture content becomes vital for control set points and timely feedback. Reliable sensors have long been on the "wish list" of mineral processors since the problem has always been that you can only control what you can measure. Today, the task of moisture determination is still done in the classical technique of loss in weight utilizing uncontrolled procedures. These same methods were introduced in the earliest base metal concentrators. Generally, it is acceptable to have ore concentrate moisture content vary within a range of 7 to 9%. Many times, delays in manually achieving reliable feedback on the moisture content results in the moisture varying from 5 to 12% before corrective actions can be made. This paper first reviews the traditional and widely available methods for determining moisture content in granular materials by applying physical principals and properties to measure moisture content. All methods are in some form affected when employed on mineral ore concentrates. This paper describes a unique and promising on-line moisture sensor in two mineral processing applications, which not only automates the tedious tasks but also results in reliable moisture feedback that can be used in the optimization of the de-watering process equipment such as pressure or vacuum filters and fuel-fired driers. Finally, two measurement applications will be presented to indicate the usefulness and to summarize the measurement requirements for the proposed method of employing drag force and mechanical properties of the material itself to determine the moisture content.

Jan 1, 2002

By William Gleason

During the past five years, mining operations have had access to press technology for piping and joint fittings that can save owners a significant amount of time when installing or replacing pipes by eliminating the need for welding or threading. Viega, with North American headquarters in Wichita, KA, entered the mining sector in 2009, adding to its already expanding industrial sector. Since then, the company?s global engineering department has paid considerable attention to its industrial division, bringing its expertise in plumbing solutions for residential and commercial buildings to the mining and mineral extraction industry. ?We have a lot of applications in the mining industry.?We have a lot of applications in the mining industry throughout the United States, Canada and Mexico and continue to expand in the mining industry,? Tom Shields, Viega?s director for industrial accounts explained. ?Since we made the decision to increase our presence in the industrial markets, we have been aggressive and more than 240 applications have been approved by our engineering department in Germany.? Getting approval from Viega?s engineering department is no small feat. During a tour of the manufacturing facilities in Ennest and Großheringen, Germany, Mining Engineering, as well as a select few other publications and clients, were shown Viega?s manufacturing process. At the Ennest facility, hundreds of millions of fittings are produced, and each one is inspected mechanically and with a laser at the end of the production line. With four production facilities in Germany and one in the United States, Viega is able to ship to anywhere in the world. The company distributes everything from fittings to stainless steel pipe.

By Michael J. Sapko, Robert A. Cortese

A flame powered trigger device has been developed to explosively activate suppression barriers to quench gas and coal dust explosions. The important feature of the device is a silicon solar panel, which collects 0.3 p to 1.1 D wavelength radiation from the developing explosion, and generates electrical energy to initiate a detonator, which in turn causes the rapid explosive release of an extinguishing agent into the advancing flame front. Solar panels that are rated to produce 20 w of electrical power when exposed to the sun light are producing about 200 w when exposed to full-scale dust explosion propagating in the U.S. Bureau of Mines' Lake Lynn Experimental Mine. The solar panel is electrically isolated from the detonator by a pressure sensitive switch until the arrival of the precursor pressure pulse, which always precedes a deflagration. This combination of pressure arming and flame powered photo generator prevents false barrier activation and requires no external power supply.

Jan 1, 1991

By H. F. Haller

Large volume sand plugs are placed in tunnels to stem underground explosions at the Atomic Energy Commision's Nevada Test Site. Placement through long, narrow accessways is like stemming coyote holes and blast chambers in mining and construction. Experience with several other methods showed that pipeline conveying could be preferable. Small scale tests justified predicting a placement rate of 20 y. p. h. at 1000 feet, with a modified gunite placer. The initial production trial placed over 2000 c. y. and was estimated to effect a small cost saving after paying for new equipment. Initial problems included duct replacement and supply delays, dust, and other personnel hazards. Operations analysis and SOP'S reduced delays during the second field trial, minimized hazards, doubled production. Re cent re search and operations analyses produced data on abrasion resistant ducts, identified minor equipment modifications which can improve production, developed techniques for impact compaction to 90% ?maximum? and for extension of the practical range to 2000 feet. Twenty-two illustrations include an air consumption-distance chart.

Jan 1, 1967

By V. Rajaram, D. P. O’Connor, L. Sakamoto

In 1988, the Metropolitan Water Reclamation District of Greater Chicago (MWRD) imposed a no-blasting specification (blasting is restricted to the construction shaft and shaft bottom or boot) on the Deep Tunnel project. This was prompted by numerous complaints from residents in the vicinity of the project and controversies experienced on previous projects from blasting the rock overlying the tunnel. This paper will describe the methods used by two major contractors driving 20 km (12.5 miles) of tunnel, and drilling more than 36 shafts under this restrictive specification. The impacts are detailed on design, construction, schedule, cost and the environment.

Jan 1, 1993

By Michael Li

Unsaturated flow and solute transport were studied in three large columns measuring 1.5 m diameter x 2 m height, loaded with up to 3.7 t of oxidised waste rock, which was excavated from the Stratmat pile at Heath Steele Division, Noranda Inc. and contained elevated concentrations of zinc in the pore water. The bottom of each column was partitioned into 37 squares, each of which was drained independently. Following rain simulations at the top of the rock bed, the drainage in each drain port was monitored for volume and physicochemical parameters at pre-determined intervals. This paper describes some of the observations resulting from the experiments. The main conclusion of the study is that unsaturated flows in waste rock are heterogeneous, and flow channelling is ubiquitous. The results imply that the transport of solutes from oxidised waste rock to its toe drainage is subject to various controlling mechanisms, including geochemical equilibrium control and successive pore water dilution control.

Jan 1, 2000

By D. Kang, K. N. Han

The adsorption behavior of silver in ammoniacal solutions on activated carbon was studied. In addition to the concentration of ammonia, the parameters that affect adsorption include temperature, degree of agitation and anion and cation concentrations. In the study, it was found that the adsorption of silver from ammoniacal solutions is dependent on the initial silver concentration in the solution. It was also found that the recovery of silver from ammoniacal solutions is not as effective us gold. The adsorption rate was relatively slow overall, despite a rapid initial adsorption. The apparent activation energy ,for the adsorption was measured at 30.2 kJ/mol. It was believed that the kinetics of the silver adsorption on activated carbon was limited by a mixed control mechanism.

Jan 1, 1999

By J. W. Merks

Applied statistics provides scores of powerful tests and techniques that are widely used and abused in science and engineering. The variance is the basic measure for variability, precision and risk. The formulas for the variances of the arithmetic mean and the weighted average are derived from the variance of a general function, as defined in probability theory. The requirement of functional or mathematical independence in probability theory translates into the concept of degrees of freedom in applied statistics. Geostatistics is the only variant of statistics in which functional dependence and degrees of freedom are irrelevant. This paper examines whether such basic elements of probability and statistics can be ignored with impunity.

Jan 1, 1997

By R. J. Lutton

The U. S. Army Corps of Engineers is seeking empirical slope data from mining companies and other organizations to help establish guides for engineering Judgment in crater excavation for canals and other civil works. Slopes from about 100 open pits and other excavations range in heights to greater than 1000 ft. Factors known or expected to affect stability (and optimum slope inclination) are: geological structural orientation, geological structural ordering, method and technique of blasting, design life of slope, groundwater conditions, depth of excavation, climate, and height. These and other more subtle factors appear to combine and produce an overall effect brought out best on a family of empirical curves relating slope height and inclination.

Jan 1, 1968

By S. Hodgson

Introduction The Red Dog zinc/lead deposit in northwest Alaska is the second largest zinc deposit ever discovered. Being developed by Cominco Alaska, with startup scheduled for early 1990, it will ultimately be the largest zinc mine in the Western World. Table 1 shows the reserves of the deposit. Bob Baker, a local bush pilot, discovered Red Dog in 1968. The US Geological Survey assessed the find. But the Red Dog site had been withdrawn from staking by provisions in the Alaska Native Claims Settlement Act of 1971 (ANCSA). Under the terms of ANCSA, the deposit was selected by the NANA Regional Corporation, one of 13 native corporations established by the Act. Then, in 1980, the US Congress confirmed this selection, in the Alaska National Interest Lands Conservation Act. In 1982, Cominco and NANA reached an agreement that has led to the development of the mine. Under the agreement, Cominco leases the property from NANA, develops and operates the mine, and markets the concentrate produced. In return, NANA receives royalties and, after capital recovery, participates in the net proceeds from the operation. The Alaska State Government is also playing a role in the development of the mine. Under the auspices of the Alaska Industrial Development Authority (AIDA), the state will construct, own, and operate the DeLong Mountains Regional Transportation System. This consists of a 84-km (52¬mile) road from the minesite to the Chukchi Sea. Located here are the port facilities necessary to store and ship the annual concentrate production and receive the mine fuel and supplies. For using this transportation system, Cominco will pay an annual toll fee. Over the anticipated 50 year life of the operation, the fee will provide a 6.5% return to the State of Alaska. In late 1986, Cominco's Board of Directors approved the Red Dog project. And, during the summer of 1987, road construction began. In February 1988, initial stripping began at the ore body and construction started at the millsite. Project setting The project site is approximately 1000 km (600 miles) northwest of Anchorage, 84 km (52 miles) east of tidewater on the Chukchi Sea, and 192 km (120 miles) north of the Arctic Circle (Fig. 1). The countryside consists of low, rolling hills that lead into mountains north and east of the deposit. The vegetation is typical tundra mat. And the site is in an area of permafrost. However, the permafrost is relatively warm and some areas have been found to be thawed. Examples would be creek bottoms and the site of the main waste dump.

Jan 12, 1988

By Richard M. Tinlin

Some of the practices of the mining industry that may place an undesirable stress on the groundwater environment are coming under increasing scrutiny from legislators and regulatory agencies. Among these practices are mine dewatering, the use of tailings ponds, land rehabilitation, and technological innovations such as in situ leaching of waste clumps and ore deposits. Pernichele, noting that 24 states have enacted legislation controlling to varying degrees the environmental effects of mining, has emphasized the importance of assessing the potential for damage to groundwater when evaluating, planning, and designing mining projects. 1 Illinois has enacted legislation requiring anyone opening, operating or abandoning a mine site to obtain a permit from the Illinois EPA. The law is one of the first to require regular monitoring and reporting to a control agency. Legislation has also been recently enacted at the national level that will have a significant impact on the mining industry; e. g., the Federal Water Pollution Control Act Amendments of 1972 (Public Law 92-500). The stated objective of this Act is to restore and maintain the chemical, physical and biological integrity of the nation's waters. Specifically, according to Sec. 102(a), the Administrator of the U.S. Environmental Protection Agency (EPA) is required to prepare or develop comprehensive programs for preventing, reducing or eliminating the pollution of the navigable waters and groundwaters and improving the sanitary condition of surface and underground waters. The definition of the terms "pollution" and "pollutant" is of particular significance to those who must comply with PL 92-500. The definitions are quite broad and include most of the adverse water quality effects of man's activities. As defined in Sec. 502(19), "pollution means the man-made or man-induced alteration of the chemical, physical, biological and radiological integrity of water." Within the Act, the list of pollutants includes dredged spoil, solid waste, incineration residue, chemical wastes, radioaetive materials, heat, wrecked or discarded equipment, rock, sand, cellar dirt, and industrial waste discharged into water.

Jan 1, 1973

By M. Liu

In-situ soil washing using surfactants shows great potential to remove hydrophobic organics from subsurface environment. Lab scale soil washing experiment were performed using Sodium Dodecylsulfate (SDS), an anionic surfactant, and anthracene, a highly hydrophobic compound. The results of this research show that solubility of anthracene increases linearly with an increase in SDS concentration above the critical micelle concentration. Furthermore, SDS can be effective in removing anthracene from contaminated sand.

Jan 1, 1992

By Nikolay M. Sirakov, Michael L. Feves, Rumen P. Mironov, Daniel R. Hack

Subsurface investigation of sand and gravel deposits has generally been limited to test pits and borings. These techniques are problematic in terms of the accuracy, usability, and cost of the final data. Innovations in the application of geophysics have been gaining acceptance in the aggregate industry, especially to determine depth to bedrock and the extent of uneconomic inclusions. This paper presents a system to optimize the processing and evaluation of electrical resistivity data. The system uses 3D separation, geometrical reconstruction, and visualization of subsurface objects.

Jan 1, 2002

By James D. Hervol, Josepph W. III Leonard, Barbara J. Arnold

INTRODUCTION Dry concentration or pneumatic cleaning uses air currents as the separating medium. Pneumatic cleaning in the United States today is limited to three or four operations. In fact, the quantity of bituminous coal cleaned pneumatically has declined from its peak in 1965 of about 25.4 million tons (23.1 Mt) to its current level (1988) of less than 4 million tons (3.64 Mt) annually, as shown in Fig. 7-9 1. In 1940, pneumatic methods accounted for 15% of the bituminous coal and lignite cleaned in the United States as given in Table 7-32. Currently, pneumatic methods account for less than 2%. The largest air plant was built in Pennsylvania about 1968 with 14 units processing 1400 tph (1280 t/h) of 3/, in. X 0 (19 mm X 0) raw feed and two additional units retreating middlings. This same plant is one of only three or four plants still operating air-cleaning devices in the US. A wet plant was added in 1985 to increase the efficiency of cleaning the fines. The air plant is still used as a scalping operation for the coarse material. Five additional operations are either no longer in production or have discontinued the use of air tables within the last year. Wet cleaning methods are now being employed at the facilities that have discontinued air table operation. he advantage of dry cleaning techniques is the low moisture content of the clean coal product. However, to decrease respirable dust, mining operations must use water sprays on modem mining equipment. This water adds to the moisture content of the run-of-mine coal and decreases the effectiveness of dry cleaning processes that rely on low surface moistures in the feed to allow for good separations. Wet cleaning methods are preferred, especially since they also allow for much sharper separations. The advantage of dry cleaning techniques is the low moisture content of the clean coal product. However, to decrease respirable dust, mining operations must use water sprays on modem mining equipment. This water adds to the moisture content of the run-of-mine coal and decreases the effectiveness of dry cleaning processes that rely on low surface moistures in the feed to allow for good separations. Wet cleaning methods are preferred, especially since they also allow for much sharper separations. Despite dry concentration's drawbacks, research has continued into dry concentrating methods, including both electrostatic and magnetic separation techniques. The real application for future dry cleaning processes is probably at the power plant between the pulverizer and the boiler feed where particles are already dry and ground to fine sizes (- 200 mesh [ -0.075 mm]), increasing the effectiveness of the separation and also, possibly, increasing the liberation of clean coal from finely disseminated impurities. From a utility's viewpoint, pneumatic cleaning offers the best delivered Btu cost, based on the premise that a percent of moisture is just as detrimental as a percent of ash. Additionally, several other advantages are inherent in dry concentration techniques. The main advantage is that dry concentration re-

Jan 1, 1991

By C. D. Mann

INTRODUCTION The sublevel stoping mining method is usually applied to a relatively steeply dipping, competent ore body, surrounded by competent wall rock. Ore is produced by drilling and blasting longholes, which can range from 50 mm (2 in.) to 200 mm (7% in.) diam, with lengths up to 90 m (300 ft). Longholes can be inclined in any direction, but the ring or pattern usually forms a plane, and the holes are blasted as a unit. Recently developed mobile drilling and loading machinery, as well as new explosives products, blasting techniques, and cemented sand and rock fill have made sublevel stoping a highly efficient and versatile mining method. When designing a sublevel stoping production sys- tem, it should be kept in mind that production rates from conventional sublevel stopes vary widely through- out the life of the stope. Early production is at a low rate, coming only from the drawpoints near the slot, but increases as new drawpoints are reached by the stope face. As the stope nears completion, again, fewer drawpoints are productive. Enough drawpoints must be available at any time to provide required production. Drawpoint availability should be compared to equipment availability; plan for more drawpoints than are needed at any one time. Accurate, realistic scheduling is essential to smooth production rates. Also, initial recovery of ore in a stope/pillar block is normally from 35% to 50% in sublevel stoping. Planning of pillar recovery, representing the majority of ore tonnage in a production block, must be done during early mine planning. Since much of the development already done for primary stoping (access for drilling, drawpoints, and haulageways), can be used for pillar recovery, early production from pillars is highly desirable. The following description of components of the system is an attempt to highlight some of the most important features and requirements of mechanized sublevel stoping methods. Similar comments would apply to the use of older equipment (column-and-arm drill setups, slushers, etc.) in similar methods. As in any good mining system, maximum economic recovery of the resource in the ground is the primary consideration. STOPE DESIGN CHARACTERISTICS Length and Width The following are some of the factors which affect sublevel open stope length and width dimensions: ore body geometry, principal stress directions, competence of stope back, optimum drill pattern, and drilling drift layout. In new mines initial stope layout design may occur before the ore body is actually intersected by mine workings. Stope dimensioning is a critical decision, and assistance from as many knowledgeable people as possible at this stage is essential. Operators with past experience in similar ore bodies, rock mechanics experts, and others with mine design experience should participate at this stage of stope planning. Height The following are some of the factors which must be considered in determining stope height: competence of stope pillar and stope/fill walls; slenderness ratio of adjacent pillars; ore body dip; ore body thickness; hole depth capability of the drilling machine; fragmentation characteristics of the ore; and level intervals in existing mines. In competent ground, drill-hole length and accuracy are the most important determinants of stoping height. Frequently entire drilling sublevels can be eliminated because of the depth capability of sophisticated drilling equipment, resulting in significant development cost savings. Drawpoint Location and Design Some of the most important considerations of a good drawpoint system are optimum spacing of draw- points, within the constraints of stope dimensions, for uniform drawdown and maximum recovery; excavations designed for stability for the life of the ore block to be drawn-primary stope ore as well as subsequent pillar ore; floor or roadway design including type of surface, reinforcing, grade for water runoff; orientation with respect to the main haulageway, for optimum loader maneuverability and ground stability at the inter- section; and length, to allow articulated front-end loaders to work in a straight configuration. Careful drawpoint design and construction are keys to successful production. Extra care in development, such as smooth wall blasting, rockbolts or grouted rebar, wire mesh, and shotcrete usually will ensure long draw- point life. Human exposure during production loading is of longer duration than during development or production drilling, and consequently preparation of draw- points is easily justified, particularly when pillar ore can be drawn through the same drawpoints. Secondary blasting of boulders can weaken drawpoints, also justifying good ground control techniques. A smooth draw- point floor of poured, reinforced concrete, on a grade of +3% or +4% toward the ore pile facilitates water flow out of the drawpoint, and ease of loader bucket penetration into the muck pile. Slot Raising, Slotting A slot or other space for rock expansion is necessary in conventional sublevel stoping where vertical rings or rows of holes are blasted. The slot can be started at a slot raise driven by conventional raising methods, raise boring, drop raising (predrilling and blasting a raise from the top, using small diameter-less than 200-mm (7%-in.)-holes for relief), or crater blasting (similar to drop raising, but without relief holes). The slot usually extends from the extraction level to the back of the stope. It is normally expanded to full stope width by

Jan 1, 1982

By BO HYUN KIM, MARK K. LARSON

The floor-heave and no-floor-heave phenomena at a western U.S. coal mine could not be properly simulated in numerical models using conventional shear-dominant failure criteria. Although the previous numerical study using FLAC3D very reasonably demonstrated these phenomena, 3DEC modeling in conjunction with the discrete fracture network (DFN) technique was performed to better understand the true behavior of floor heave associated with underground mining in an anisotropic stress field. As a result, the latter models predicted floor heave that agreed with relative amounts of observed heave from each gateroad system, but the cause of heave was mainly related to the degree of anisotropy instead of the size of the pillar.

Sep 1, 2022

By A. S. Ibrado

The adsorption of silver on activated carbon from cyanide solutions was studied as a function of concentration, ionic strength and pH. In cyanide solutions, silver exists mainly as the linear Ag(CN)2 complex and adsorbs on activated carbon following the Freundlich isotherm. The uptake and rate of adsorption increase with the addition of KC1 and KNO3 but changes only slightly with pH. In contrast, the adsorption of Cu(I), Zn(II), Cd(II), and Hg(II) shows marked changes with pH, closely following the predominance profiles of their neutral and singly-charged cyano complexes. Clearly, multicharged negative complexes are repelled by the negatively-charged carbon surface. This sensitivity of activated carbon to the charge of the adsorbing species indicates that silver adsorbs as an anion, not chemically bound to the co-adsorbing counterions. For the same reason, activated carbon is selective to metals that form neutral and Singly-charged cyano complexes, namely gold and silver.

Jan 1, 1988