Search Documents

By John E. Litz, Charles W. Kenney, Wayne Carter

Refractory gold ore pretreatment processes continue to receive much attention. This paper compares the relative economics of treating ores by oxygen pressure oxidation, roasting and bacterial oxidation with or without preconcentration by froth flotation. Capital and operating cost estimates for each method of pretreatment were prepared and these estimated costs and ore sulfide grades then are used to compare the process economics. The study indicates that the most significant item affecting the economics is the amenability of the ore to flotation. The cost benefits of flotation are $10-13 per tonne ore processed (2%-4% s=, 10:1 ratio of concentration). In most cases bacterial oxidation has the lowest overall cost, especially if less than complete oxidation of the sulfides will give acceptable recovery, however bacterial oxidation has yet to be practiced on a large scale. In all situations pressure oxidation shows the highest cost. However, the cost differences between the treatments are small, less than $7 per tonne.

Jan 1, 1990

By M. J. Liesveld, D. Liesveld

For a Colorado mountain quarry, the Water Jet Channeling Method is far superior to Burning, Sawing, Drilling, or Shooting with Primer Cord, Water, or Black Powder. Throughout the life of our quarry, which was founded in 1947, we have used all the methods and turned to the Water Jet Channeler, which we invented and patented as our ideal way to remove dimension granite from our quarry. We jet the block on 4 sides and remove the block with plugs and feathers on the backside. The Water Jet uses approx 7.5 l/m (2 gpm) running at310,000 kPa (45,000 psi) to erode the crystals @ 1sm/h (10sf/h).The 0.533mm (.021”) nozzle oscillates back and forth to achieve an approx 5cm (2”) channel. Using the Jet, we do not lose corners or cause cracks in our red fine grain light class 5 granite.

Jan 1, 2004

By G. Kritikakis

Rehabilitation of sites contaminated by oil products and chlorinated organic compounds is a costly task which affects the planning of urban and infrastructure development. An integrated approach based on the non-invasive geophysical technology is utilized for subsurface characterization of contaminated land. In this approach the localized information, provided by chemical analysis of soil samples collected from bore-holes, is used for the calibration of the geophysical data. This information is subsequently extrapolated to the area under investigation by combining it with the geophysical results, providing thus information about pollution accumulation, contaminants? flow and pollution sources. Two case studies are presented from sites contaminated by heavy metals (Venice, Italy) and oil products (Athens, Greece). Resistivity, electromagnetic and seismic methods were used in this approach. Namely, electrical tomography, electromagnetic mapping, ground penetrating radar (GPR), multichannel analysis of surface waves (MASW) and seismic refraction experiments were conducted. In Italy, the sections from the multichannel analysis of surface waves imaged successfully a buried channel where the pollution is concentrated. Preliminary results are also discussed from the geophysical survey in Greece where the thickness of the oil phase located on top of the water layer is 60 cm.

Jan 1, 2006

The surface of chalcopyrite was studied in situ in aqueous solution by an atomic force microscopy (AFM). The AFM images showed that some absorbate in patches was detected on the mineral surface, after the chalcopyrite sample was soaked in 5x10-4M potassium ethyl xanthate (KEX) solution at pH 11 for 10 minutes. These patches increased in size with time elapsing. At the same time, as shown by the obtained AFM force curves, the adhesion between the AFM tip and the substrate increased greatly due to the adsorption. Rinsing with ethanol removed the absorbate from the chalcopyrite surface, as well as the big adhesion observed in KEX solution.

Jan 1, 2010

By M. C. Stuttle

MDL Rock Lasers has undertaken successful mapping trials of abandoned mine workings using its underground cavity scanning system. The work was being performed for Kalgoorlie Consolidated Gold Mines (KCGM), Australia's largest gold producer. MDL Rock Lasers supplies underground surveying systems to the mining and quarrying industry KCGM's Fimiston Super Pit, located in Kalgoorlie, Western Australia, is Australia's largest open-pit gold operation. Fimiston's final pit design is expected to be 3.7 km (2.3 miles) long, 1.5 km (0.9-miles ) wide and 540 m (1,770 ft) deep. During the early days of Australian mining, underground operations were labor intensive. Mining was selective and generally narrow stopes were mostly backfilled. Improved processing technology and mine mechanization during the 1970s and 1980s has permitted larger scale operations to adopt less selective underground-stope operations. The "super pit" concept was a logical step for mining companies working toward economies of scale. However, the industry recognized that there was no precedent for excavating a 500-m- (1,640-ft-) deep open pit through ground previously affected by old workings. To appreciate the geotechnical challenge facing KCGM, it is necessary to consider that under the pro¬posed area at the open pit, stoping reached a level of 1 km (0.6 miles) and was supported by more than 2,000 km (1,240 miles) of development headings. The company was fortunate because plans were available for the Golden Mile underground operations. The existing plans were interpreted by the mine's geotechnical team and computer models were constructed of the underground workings. These models can be imported into three-dimensional mine planning packages, such as the Vulcan's Unix-based software, Envisage, to assist analysis and design. This prior knowledge of the workings provided the focus for investigating and confirming ground conditions using probe drilling. After several iterations of drilling, followed by detailed analysis, several decisions were made relating to the nature of the ground and the mining approach to be taken. It was recognized that the stope models were not perfect due to hu¬man error, lack of original survey information and progressive deterioration in ground conditions. It also became apparent that the sole reliance on probe drilling was inefficient in terms of time and quality of information. This was particularly true in complex areas where stopes are in close proximity. A major concern was the presence of open stopes (voids). In many cases, stopes consist of combinations of filled and void sections. The condition of pillars within these underground workings is extremely important. In time, pillars collapse and voids will propagate in upward and lateral directions. So systems needed to be developed that allowed rapid and accurate verification of ground conditions. KCGM was introduced to MDL Rock Lasers while investigating technology for underground mining. The two companies decided to use the C-ALS, MDL Rock Laser's underground laser, cavity scanning system, to improve the management of mining through affected ground. This system was to be used in conjunction with probe drilling and void mapping activities. A field test in one area of the Fimiston Mine verified the capability of the C-ALS system to quickly and efficiently assist in this decision making process. The C-ALS scanner features lightweight, carbon fi¬ber alignment rods from Measurement Devices Ltd.'s (MDL) Boretrak MKII. This is a borehole deviation system that stops the two axis measurement head rotating and lowers the system down a borehole. The scanner is deployed by a 110-mm (4.3-in.) borehole, up, down or sideways. The operator can then carry out vertical and horizontal plan section scans at any user specified ARC (an angular increment of 2°) or the distance between two points on the ARC (CHORD) increments. Windows '95 software enables the operator to control the cavity scanner remotely, surveying the area in real time. The system makes data quick and convenient.

Jan 1, 1999

By Peter E. Hart

The search for mineral deposits is a difficult high-risk enterprise whose likelihood of success is influenced by a great many factors. Among the most important of these factors are the knowledge and judgment brought to bear on an exploration problem. If, for example, a panel of expert highly experienced geologists could be convened to examine every prospect, it is at least plausible that fewer deposits would be overlooked in the exploration process. Unfortunately, whether a project is undertaken by a private company or a government agency, it is not usually feasible to convene such a panel. Our purpose in this chapter is to describe an experimental system of computer programs called PROSPECTOR that is intended ultimately to provide expert consultation on problems of mineral exploration and resource evaluation. Ideally, PROSPECTOR would serve as a surrogate for a panel of expert economic geologists. However, because the cost of computation is very low and is projected to drop by a factor of about 100 over the next two decades, systems like PROSPECTOR could be made available to the exploration enterprise at large. When consulting about a prospect, the PROSPECTOR system first gives the field geologist an opportunity to tell the program about the most significant features of the site: the major rock types, minerals, and alteration products. The system then compares these observations with a number of stored models of various types of ore deposits and forms alternative hypotheses about the types of deposits that might be present. The system next engages the geologist in a dialogue in order to obtain additional data that would be useful in resolving the multiple hypotheses. The geologist can interrupt the system at any time to obtain clarifications of questions, volunteer additional data, request the reason a particular question has been asked, or obtain a general summary of the state of the consultation process.

Jan 1, 1979

By Osvaldo A. Bascur, J. Pat Kennedy

Large metallurgical complexes have more data than a small city and much of it is "real time," changing rapidly as internal and external conditions evolve. As corporations buy and sell assets and reengineer their staff, the structures and tools that were used to understand these data are lost. The lack of an integrated approach makes the profitability of metallurgical plants lag behind that of other industries despite technical advances that have occurred in recent years. This results in significant deterioration in the ability to maintain a "smart” operation. The solution is to use the sophisticated new tools built for the Internet so as to leverage information in a familiar browser format that people can use and understand. Combining real-time infrastructure with portal technology is becoming an accepted methodology. This paper introduces real-time portals and team sites to support decision making by work- groups which require both real-time and documentary information from manufacturing assets, vendors, head office and the Internet. Workers get insight from the overall process effectiveness index based on key variables such as losses due to plant availability, performance efficiency and rate of quality. Real-time portals and smart clients are part of any real-time performance management (RtPM) solution. Three case studies in large metallurgical complexes are presented. PLANTS ARE YOUR STRATEGIC HANDICAP Information technology is arguably one of the fastest moving technologies used by the mining/metallurgical industry. However, the business model for managing that

Jan 1, 2004

Mineral processes are relatively simple and metallurgical accounting would also be simple if it were not for the nature of the raw materials and the large scale of operations. Essentially the balance between input and output requires only weighing and assaying of the feed, salable products, and waste. but because of complexities to be described in the following pages there are few plants that do not encounter difficulties that cause some sacrifice of precision for economy and practicality. In arriving at a sound compromise, capable

Jan 1, 1985

By D. Elsworth, M. Bai

The influence of mining on the hydro-geo-mechanical environment can be greatly modified by alternating mining geometries. The limiting magnitudes of surface subsidence and groundwater flow over the mining area, as a result of mine geometric changes, can be reasonably predicted through the coupled finite-element model introduced in this paper. The model has been verified using real and conceptual case studies which reveal that changes in strata conductivities are strongly related to the strata deformation induced by mining. The greatest modification of hydraulic conductivities occurs within the caving or severely fractured zones. The study indicates that narrowing the panel face width will substantially reduce both the intensity and extent of mining damage to the overlying strata, limit surface subsidence and constrain the change in hydraulic conductivity to a reduced scale and smaller extent, particularly as mining depth increases.

Jan 1, 1995

By Harry H. Posey, John Woodling, Miriam L. Renkin

Natural acid drainage is generated from pyritic rock underlying 17 percent of the upper Alamosa River basin. About one-third of these acid producing rocks have nil carbonate buffering capacity; there the streams carry significant acid plus dissolved Al, Cu, Fe, and Zn. In part of the basin, aquatic life is limited by the natural acid drainage. In the four miles where the Alamosa flows through pyritic rock the river grows toxic to trout. Inhospitable conditions continue downstream for at least another four miles. The waters become refreshed, naturally, through metal dilution, metal oxide and hydroxide precipitation, and acid neutralization. Water quality fluctuates in seasonal cycles. Dissolved metals and acid, which are generated year-round by weathering, are stored over winter in the unsaturated zone in the retained water and in soluble metal- sulfate minerals that form by evaporation of acid-metal waters. Seasonal discharge variations cause metal concentrations and pH to shift in the trunk stream; the acid drainage source streams, however, shift only slightly by season. In early spring, metal concentrations and metal loads increase as metals and acid are flushed from the unsaturated zones by melting snow. Peak metal loads occur at this time, and precede peak flow by up to two months. Other metal load peaks occur during peak flow and monsoon flow, even though metal concentrations are diluted at that time by precipitation. In late spring and thereafter, discharge of neutral pH water wanes, so trunk stream pH falls and metal concentrations return to previous high levels. Metal concentrations appear to be low from November through January when dilution from precipitation is lowest, but rise in February to near peak yearly concentrations. In years with high monsoonal flows, metal-laden waters apparently flush from the unsaturated zone and metal concentrations remain low from about October through January. In years with low monsoonal flows, however, metal concentrations in October and November at least are higher.

Jan 1, 2000

By Aditya Rana, A. K. Mishra, M. M. Singh, N. K. Bhagat

Many cases of derailments, train accidents and traffic interruptions due to the slope failure and rockfall have been reported in the past on Konkan Railway trackline because of unstable rock slopes. The authorities installed stability enhancement measures such as wire netting, rock bolting and shotcreting which were found insufficient. The failed geotechnical measures prompted authorities to excavate the unstable slopes. Rock blasting is generally not preferred for the excavation of slopes along the transportation route. Stabilisation and widening of slopes by blasting need closure of the route for a considerable time. Discontinuing traffic on Konkan Railway route was undesirable as it connects two important port cities Mumbai and Mangalore. The paper presents an innovative directional controlled blasting (DCB) technique for excavating three unstable slopes (i.e. cuttings) in hilly terrain without disturbing the traffic. New empirical formulae for small geometry blasting to estimate burden and throw have been developed. A unique sequence of firing and excavation with powder factor varying between 0.04 and 0.39 kg/m3 irrespective of the actual free face was used for rock blasting. The process controlled the throw of blasted material over the track and resulted in a smooth and stable wall. The slope angle has been changed from 80 to 82° to 45–47° and probability of wedge, planar and toppling failures was eliminated. About 100 such accident-prone slopes (52 km cumulative length, 7% of total route) situated at discrete locations along Konkan Railway route were stabilised using the technique. No incident of rockfall and slope failures along these slopes has been observed after the stabilisation.

By Colin Irwin, Adrian Naranjo-Castillo, Christopher Petta, Eric Zarobila

The Shoreline Consolidation Sewer is a CSO control project in Cleveland, Ohio that requires the installation of 5,000 feet of 72-inch inside diameter pipe using microtunneling methods. After award, the contractor submitted a value engineering proposal to eliminate two deep shafts and install the tunnel in two drives instead of four. In an example of successful collaboration, owner, contractor, and engineer worked together during the initial construction stages to modify the design and update the contract documents. This paper examines the importance of exible requirements in contract documents and a collaborative environment between all parties to successfully deliver a project.

Jun 23, 2024

By Hesam Dehghani, Farid Alimohammadnia, Nima Babanouri, Mokhtar Kalhori

In open-pit mining, blasting pattern design is performed to achieve a desired degree of fragmentation for loading, hauling, and crushing operations. Inappropriate fragmentation of rock will result in numerous problems such as incurring extra costs for secondary blasting, production interruption, etc. Wetness of the blast holes is one of the most important factors, which can cause the inappropriate rock fragmentation. Lowering ambient temperature in the vicinity of the explosion, the presence of water in the hole adversely affects the quality of the explosive while dissipating part of the explosion energy, ending up with inappropriate fragmentation problems. In the present research, in order to study blast-induced fragmentation conditions in Baba-Ali Iron Ore Mine, three scenarios were considered: explosion of ammonium nitrate with fuel oil (ANFO) in dry hole, explosion of ANFO in wet hole, and explosion of the emulsion in wet hole. For this purpose LS-DYNA, a numerical simulation code was used. Results of the present research showed that, compared to the explosion of ANFO in wet hole, the explosion of the emulsion produced more uniform distribution of fragment size, while the explosion of ANFO in dry hole resulted in fewer large fragments.

By Thomas H. Koenning

The number of spontaneous combustion incidents in the U.S. is expected to increase as the consumption of lower rank coals and the use of longwall mining becomes more prevalent. A spontaneous combustion incident holds the potential for substantial loss of life from a mine fire or explosion if not prevented or controlled at an early stage. Laboratory tests have been developed which are useful in ranking the susceptibility of various coals to spontaneous combustion. Ventilation circuits and mining methods can be designed to minimize the risk of spontaneous combustion. Early detection of spontaneous combustion is possible with the combined use of continuous monitoring, periodic gas sampling, and inspection.

Jan 1, 1989

By D. Morin, J. Villeneuve, S. Foucher

The development of new processes has to follow "best practice" rules in order to be technically and economically as efficient as possible. However, innovations, new process routes and new rules are continuously emerging to minimize financial risk and maximize environmental compliance. Process simulation, which offers a complete overview of the flowsheet, makes it possible to cope with this new challenge-minimizing waste production and water consumption. Furthermore, simulation provides an estimate, at the early stage, of the cost of alternative technical routes. Four examples involving biotechnological circuits are presented, both at the design and commissioning stages.

Jan 1, 2000

By B. Mather

I was very glad to see an article on alkali-silica reactivity of concrete aggregate in Mining Engineering. It is a topic that should be reexamined every 45 or 50 years. The last paper (that I am aware of) that examined this topic in Mining Engineering was Rexford (1950), who, at the time, was chief of the Petrography Section, South Pacific Division Laboratory, Corps of Engineers, Los Angeles, CA. The paper was presented at the AIME meeting in Los Angeles in October 1948. Professor Leming's discussion generally reflects the current state-of-the-art; but it provides no references for more detailed information. I wrote a paper titled "How to avoid excessive expansion of concrete due to alkali-aggregate reaction," which was included in the Proceedings of the Second International Conference on Alkali-Aggregate Reactions in Hydroelectric Plants and Dams (Mather, 1995). In it, I emphasized that it was the hydroxide ion (not the alkali ion) that caused the pore fluid in the concrete to dissolve reactive silica, producing alkali-silica gel capable of taking up water, thereby, causing swelling and rupturing of the concrete. Excessive expansion will not occur unless there is a sufficient amount of potentially expansive alkali-silica reaction product and water. However, this will not occur unless there is a sufficient quantity of reactive aggregate and unless there is a mechanism by which the pH of the pore fluid can get well above the normal value of about 12.6. In many cases it is sufficient that the cementitious medium not only contains portland cement but also contains ground granulated blast-furnace slag (GGBFS) or a pozzolan such as fly ash, silica fume, metakaolin, volcanic glass or calcined shale - any of which may have been included for economic reasons. If, however, the person selecting the ingredients for concrete knows that the aggregate is reactive (with no alternate nonreactive aggregate available) and if the person knows that the only available portland cement has a high alkali content (i.e., more than 0.6% Na2O.; Na2e = % Na20 + 0.658 x % K20), then it becomes irresponsible not to establish what reasonable precaution one should take. Professor Leming suggests using one of the following: 30% Class F fly ash, 50% GGBFS or 7% to 10% silica fume. My view is that one should prepare test specimens with the cement and aggregate to be used and then expose these both with and without at least two dosages of each of the various alternative materials (slag, pozzolan and lithium salts), so that the required dosage. to control the expansion is established. Then, economic considerations can dictate the final selection. I would point out to the author that GGBFS is not a pozzolan and is not an admixture, but, rather, it is a latent hydraulic cement. An admixture is, by definition, a material other than hydraulic cement. I commend him for suggesting that aggregate producers should become more active in knowing about the reactivity of their products and the precautions needed to permit those products to be safely used in concrete.

Jan 1, 1997

By J. Kemeny, K. Girdner, M. A. Lowery

A strategy for proactive blast planning to improve the postblast fragmentation size has been implemented at the Phelps Dodge Morenci Mine. This strategy was developed in specific phases that include stabilization of blasting practices, systematic changes in blast design and quantification of the size distribution of blasts. Implementing this new strategy would not be possible without an accurate method for quantifying the postblast fragment size distribution. The Split image processing system is now being used to assess fragmentation size using muck pile digital imaging taken on a daily basis and an online fragmentation analysis system installed at the primary crushers. Drilling and blasting variables and fragmentation size are entered into a database, spatially evaluated in a geographic information system and subsequently utilized for mine planning purposes. Using this strategy, significant improvements have been made in postblast fragmentation and continued improvements are expected in the next several years.

Jan 1, 2002

By Michael Schmalzel

Freeport-McMoRan Copper & Gold, Inc. (FMI) will soon begin copper production from the Dos Pobres and San Juan deposits near Safford, Arizona. Ore reserves total 615 M tons grading 0.36% copper, predominantly as chrysocolla. Copper extraction will be by leaching with sulfuric acid. Fluor Canada Ltd. provided EPCM services to design an ore handling and conventional SWEW facility capable of producing a nominal 240 million pounds per year of cathode copper. The ore handling facility will process 114,000 tons per day of ore through three-stage, open-circuit crushing followed by agglomeration and product placement on the permanent leach pad. Stacking of ore on the leach pad will utilize Terra Nova Technologies' "Super Portable" mobile stacking system. The stacking system fleet consists of 13 self- propelled, crawler-mounted mobile conveyor units, each with 72-inch-wide belting and a capacity of 6,800 tons per hour, including ten 250-foot-long portable conveyors, a horizontal feed conveyor, a 285-foot-long horizontal conveyor and a 220-foot-long radial stacker. PROJECT BACKGROUND Project History The Safford Leach Project is located in the Safford mining district in Graham County, Arizona, approximately eight miles northeast of the town of Safford and 170 miles east of Phoenix. The 3,360-acre property is located in the Gila River Valley, immediately south of the Gila Mountains, at elevations between approximately 3,000 and 5,400 feet above sea level. The Safford Leach Project is comprised of the Dos Pobres and San Juan deposits, two of five known copper ore deposits in the Safford mining district.

Jan 1, 2008

By B. J. Scheiner

The presence of organic materials in gold ores cyanidation. The presence of organic materials interferes with gold extraction by The carbon contained in the ore has been shown to adsorb gold cyanide complex from solution. Removal of the carbon content by roasting or chemical oxidation prior to cyanidation results in gold extractions of 85 to 95 pct. This paper by the Bureau of Mines, U.S. Department of the Interior, discusses how the mineralogy of the carbonaceous gold ores affects gold recovery by cyanidation. It also discusses the advantages and disadvantages of roasting and chemical treatment to render the ore amenable to cyanidation.

Jan 1, 1987

By Steven T. Mitchell

The introduction of Vertical Crater Retreat (VCR) Stoping at the Homestake Mine in Lead, SD, constitutes a major advance in Homes take Mining Company's efforts to improve productivity and reduce costs through underground mine mechanization. The work to date indicates that Vertical Crater Retreat Stoping is one of the safest methods of underground hardrock mining today, and is competitive with all other forms of stoping in terms of cost and productivity. Homes take anticipates that VCR stoping rill account for approximately 30% of the total mine production in 1980.

Jan 1, 1980