Search Documents

By MARK J. VANARELLI

Estimating ground-water inflows in rock deep tunnels is critical to the safety of personnel constructing the tunnel and the cost of construction. This paper presents two case studies, including the Chattahoochee and Nancy Creek tunnels, for estimating steady-state ground-water inflows into deep rock tunnels. Statistical methods were applied to packer test data obtained from exploratory borings during geotechnical site investigations, and a semiempirical procedure was used to estimate ground-water inflows. The Chattahoochee and Nancy Creek tunnels are deep rock tunnels that exhibit radial flow conditions. For the radial flow condition, a statistical analysis presented in this paper indicates that the semiempirical procedure works well; however, variations in the procedure and/or an insufficient amount of testing could lead to underestimations of the inflow quantities. Modeling using Monte Carlo simulations was observed to be an effective tool for removing data distribution irregularities and incorporating high-end permeability data to derive reasonable ground-water inflow estimates.

By W.J. Atkinson

The first recorded discovery of diamonds in Australia was in 1851 from New South Wales. Subsequent prospecting has shown alluvial occurrences of diamond to be relatively widespread through much of the Tasman Fold Belts of Eastern Australia and production to date is estimated to be some 500 000 carats from a number of 'small alluvial fields. Despite extensive exploration though, no primary rock source carrying significant diamond contents has ever been confirmed in Eastern Australia. Conversely, diamond exploration of the older Western and Central Cratons of Australia over the past 30 years has discovered 12 fields containing 360 kimberlites, lamproites and lamprophyric volcanic pipes, dykes and other intrusives, of which 180 have been confirmed to be diamondiferous. Only one pipe however, the 1200 Ma high grade Argyle lamproite and associated near-by alluvials, has proved to be economically exploitable with current annual production of 40 million carats valued at approximately US$400 million. Production from the open-pit will be sustainable until at least 2003. This paper briefly summarizes the history of diamond discovery in Australia, principal diamondiferous provinces and deposits, current exploration activities and the potential for future discoveries.

Jan 1, 1995

By A. E. Koski

This paper will review recent developments in the area of mine planning at the Empire Mine. It illustrates how one of the largest iron mines in North America has adapted computerized mine planning to meet the unique requirements of their mining operation.

Jan 1, 1994

By Glenn A. Squibb

An example of market development is described. The market in rail-lake movement of coal is vital to a rail carrier because of its location. This market is threatened by nuclear and other competing fuel sources and by depressed all-rail unit train rates, The first step to develop the rail-lake transportation market consists of rate adjustments and tariff changes to force tighter scheduling of mines, railroad, port and boats, and thus reduce cost. The second step provides a surge pile at the port to eliminate most of the seasonal disadvantage of rail-lake movement and reduce car detention at the port to almost zero.

Jan 1, 1966

By Saverio Agresti, Giuseppe Lunardi, Donato Basta, Roberto Trapasso

"At a distance of 10 years from the first application of the Nazzano Method, the widening under traffic of a tube of an existing motorway tunnel was realized near Ancona, along the A14 Motorway in Italy. This paper describes the works for the enlargement with conventional method of the second tube, very close to that already widened under traffic.This enlargement was realized very fast, taking into account the advantages of some interesting technological improvements of the Final Design proved in the first tube.INTRODUCTION TO THE WIDENING OF EXISTING MOTORWAY TUNNELSThe widening of a twin-bore motorway tunnel usually considers the double option of creating a third bore as an alternative or closure to traffic of one of the two bores with the resulting reduction in the level of service for users.On the contrary, the extension in situ of a road, motorway, railway or underground tunnel in the presence of traffic, made possible by an inspired idea of Prof. Pietro Lunardi, enables the level of service of the infrastructure to be maintained without the need to resort to alternative routes to create new permanent or temporary bores, not always feasible because of the lack of the necessary space.This construction technique, known as the ‘Nazzano Method’, is part of the technologies refined and offered by the ADECO-RS approach to tunnel design and construction (Lunardi P., 2008) which is increasingly used in the world, leading to the industrialisation of tunnelling (meaning respect for the times and costs set out during detailed design) both in conventional and mechanised (through TBM) excavations.The first true experimentation of the ‘Nazzano Method’ was carried out between 2004 and 2007 to enlarge the two-bore ‘Nazzano’ tunnel (Italy, Milan-Rome A1 motorway) in the presence of traffic, widening it to house from two to four lanes in each direction (Lunardi P. et al., 2007). Following the success achieved in this first application, the Nazzano Method was strengthened considering all the possible suggestions arising from the previous experience and then taken up to enlarge the north bore of the ‘Montedomini’ two-bore tunnel (Italy, Bologna-Taranto A14 motorway), in situ and the presence of traffic."

Jan 1, 2016

By A. E. Hall, K. R. Mutama

The wind tunnel has been used extensively for mine ventilation research and continues to be a valuable tool. The advent of the powerful personal computer has reduced the use of wind tunnels because several flow problems car be simulated and investigated quickly. This paper describes the recent design and construction of a wind tunnel which is now being used for mine ventilation aerodynamic research and teaching purposes. The wind tunnel has a square cross section measuring 900 by 900 mm and is 8485 mm long from the entrance to where it joins the fan. The tunnel was designed as an open circuit suction type and is attached to a 7.5 kW variable pitch axial flow fan capable of producing over 6 m3/s of airflow. The entire length of the wind tunnel can be used for flow investigations and all activities are visible since the sides are made of plexiglass. Results are presented from the test program to show that even without honeycombs and screens air flow symmetry is achieved.

Jan 1, 1993

By Basar Arioglu, Mustafa Tanriverdi, Seok Jae Seo

"INTRODUCTION Istanbul is a unique megalopolis connecting two continents. Population growth and economic development require permanent solutions and continuous investments on the transportation infrastructure. While the average population growth rate in Turkey is around 1.3% per annum, Istanbul is growing at an even faster rate of more than 1.5%. Even more striking is the fact that car ownership in Istanbul is increasing 5% a year, which is four times faster than the population growth. Although Istanbul Metropolitan Municipality (IMM) has worked persistently to improve the quantity and quality of the public transportation system in the city through, in particular, extending the available rail system network, the need for extra roads has always fallen behind demand. To make things worse, Istanbul is divided by the Bosphorus Strait, the large waterway connecting the Black Sea to the north and Marmara Sea to the south, which leads to the Mediterranean. This waterway is crossed via two suspension bridges, the Bosphorus Bridge built in 1973 and the Fatih Sultan Mehmet Bridge built in 1988. Current daily traffic across the bridges is around 450,000 vehicles per day. Ever increasing cross-Bosphorus traffic demands require other routes to be in place a soon as possible. While a third bridge farther north is currently under construction, yet another tunnel crossing is coming to the end of construction and is planned to be in service by December 2016. Being implemented under a Build-Operate-Transfer (BOT) model, Istanbul Strait Road Tunnel Project (ISRTP, the Project) has been under the spotlight not only because of its distinctive technical characteristics but also because of its robust business model, exacting financial and legal arrangements, diverse stakeholders and challenging organizational management structure. The following paragraphs offer an overall view of the Project from inception to where it stands now and extend to the imminent operational phase, touching lightly on all major aspects of this challenging journey."

Jan 1, 2016

By Madan M. Singh

Section 516 of Public Law (PL) 95-87, commonly known as the Surface Mining Control and Reclamation Act of 1977 (SMCRA), requires that underground coal mine operators must "adopt measures consistent with known technology in order to prevent subsidence causing material damage to the extent technologically and economically feasible, maximize mine stability, and maintain the value and reasonable foreseeable use of such surface lands, except in those instances where the mining technology used requires planned subsidence in a predictable and controlled manner..." Implied in the constraints of Section 516(b)(1) of SMCRA is a determination of what constitutes "material damage" to surface structures, renewable resource lands, and the capacity for sequential land use following underground mining. The authors have already briefly addressed the subject of damage criteria in relation to surface structures (Bhattacharya et al, 1984). In this paper, an attempt is made to provide quantitative guidelines to ascertain material damage to renewable resource lands, although the data available to establish these criteria are considerably more limited than is the case for surface structures. Besides, many more variables influence the severity of the impact at a given site, making the task of assigning stringent ground movement limits even more complex. This often necessitated use of professional judgement and occasional reverting to a qualitative approach. Hence the reader is cautioned at the very outset that the quantitative limits presented herein are approximate and are primarily intended to serve as rough guides for ascertaining the extent of damage to the renewable resource lands under consideration, and that depending on site-specific conditions the actual damage incurred may differ significantly from that predicted by the proposed criteria. The authors, however, feel that the criteria suggested are somewhat conservative, but realistic. The actual damage observed should generally be less severe than predicted by these criteria. It may also be clarified here that the term "subsidence", as used in this paper, implies the total phenomenon of surface and subsurface effects associated with the mining of minerals and not only the vertical displacement of the surface as is sometimes inferred in the literature.

Jan 1, 1984

By Frederick J. Hoppe

The productivity or usefulness of a Front End Loader rises rapidly with its size. Loading is more aggressive. Mother Nature is defeated more easily. Larger tires get a better grip on the ground. Hauling equipment can be loaded more quickly. The productivity or usefulness of a Front End Loader is proportional to its working speed, both automotive and hydraulic. The price of speed is horsepower, which rises rapidly with speed. Horsepower saved shows up as increased productivity. This paper covers the development of the D600, KW-Dart's articulated loader, which combines massive size with new concepts to increase its working speed. Featured is a discussion of the horsepower saving, "Balanced Boom."

Jan 1, 1969

By Dennis Z. Mraz, Maurice B. Dusseault

INTRODUCTION In 1982 and 1983, as part of the mine design program for a New Brunswick potash mine, series of laboratory tests were conducted on potash and salt samples obtained during the mine exploration program. Concurrently, two rock mechanics monitoring programs were initiated in-situ the short term test at site A, and the long term test at site B (figures 1 and 2). SHORT TERM TEST (FIGURE 1) The purpose of this test was to obtain a quick confirmation of laboratory data and comparison of the rock response to excavation with the data available from Saskatchewan potash mines. Instrumentation in the main drift was installed on Day 4 after excavation, and the pressure cells were pressurized on Day 33. The packer type cells in the east crosscut were pressurized on Day 25. Excavation of the west cross-cut was begun on Day 71. This "mine by" test has provided important information required for calibration of laboratory tests, as will be shown later. The test data recorded are shown in a series of diagrams: a. initial room closures, main drift-figure 3; b. convergence graphs, main drift-figure 4; c. stresses recorded, main drift-figures 5 to 8 and, d. stresses recorded, east crosscut - figure15 Three types of instruments were used in this test. In the main drift. Saskatchewan Research Council water type hydraulic inclusions. encapsulated in potash, were used to measure lateral and vertical stresses. In the east crosscut a home-made packer type hydraulic inclusion was used to record radial stresses. The convergence stations consisted of end-grouted bars of reinforcing steel. LONG TERM TEST (FIGURE 2) The purpose of the long term test was to study the steady-state behaviour of a single opening in potash. Site B was placed in a remote area of the mine, well away from any anticipated early mining activities. To assure homogeneity of rock mass, the site was placed within a 30 meter thick vertical limb of a syncline-shaped ore body contained within a 360 metre thick vertical section of salt rocks. It was excavated mechanically as close as possible to the designed square cross-section for the entire length of the room. The square cross- section was chosen in order to achieve a comparable geometry in vertical and horizontal directions; that is, to eliminate any undesired effects of geometry interaction with lithostratigraphy which might have generated non-homogeneous behaviour. The site was extensively instrumented. As in site A, the convergence stations consisted of end-grouted bars of reinforcing steel. However, in order to avoid any measurement inaccuracies which would be associated with the brittle yield zone in the opening walls, bars were placed to the same depth in opposite sides of the opening. This allowed the convergence measurement to be obtained as the absolute convergence between two points, rather than the convergence of a single point with respect to a potentially unstable reference. For stress measurements the Saskatchewan Research Council cells were placed vertically, laterally and radially. Unfortunately, due to cost considerations, it was decided to use a compacted sand, rather than grout, to encapsulate the cells in the boreholes. Due to the extremely small strain rates, only radial ly placed cells could be adequately pressurized. The rest of the cells did not perform adequately, and are currently being replaced.

Jan 1, 1986

By R. C. Bunge

The selective flotation of semi-soluble salts with fatty acids is often negatively affected by the interaction of the potential determining cation with the ionic surfactant in bulk solution. This problem can be avoided by floating at low pH which involves the emulsification of the collector. The research presented here focuses on the influence of the Ca2+ ion on the flotation of fluorite with palmitic acid at low pH. Our results show that the surfaces of collector emulsions are dominated by precipitation phenomena similar to those encountered in bulk. In turn, fluorite in palmitic solution at intermediate pH displays surface properties similar to those of the collector by itself. This may be due to two alternative mechanisms (i) adsorption of bulk precipitate on the fluorite surface or (ii) the formation of a bilayer of surfactant ions on fluorite. Possibly, both mechanisms occur simultaneously.

Jan 1, 1993

By R. S. C. Rogers

A mathematical model is proposed as a general formulation for the analysis and simulation of once-through crushing machines. Methods are described which can be used to estimate parameters of the proposed model from experimental data, thus minimizing reliance on backcalculation. The applicability of the model is demonstrated in the analysis and simulation of laboratory and full scale double roll crushers, and with evidence given for a laboratory scale cone crusher. An extension of the model for closed circuit crushing is also described.

Jan 1, 1984

By George G. Reed

Approximately 200 samples of iron ores and other iron- bearing materials have been tested for amenability to treatment by the R-N process in bench scale laboratory work. Twelve large lots, ranging in size from 900 net tons to 18,500 net tons, but generally 3,000 to 4,000 tons each, have been processed in the R-N demonstration plant. The ores tested in the demonstration plant ranged from 27 to 70 percent iron content and gave excellent results. (1) The demonstration plant has a nominal daily capacity of 50 tons of high quality iron briquettes and has now operated for over five years. A continuing program of process improvement is carried on between demonstration on potential licenses ores. An important development is the complete elimination of any secondary products which, in the past (2,3,4,5), resulted from treatment of certain low-grade ores.

Jan 1, 1960

By Timothy C. Smith, S. Andrew Jacobs, Douglas E. Gonzales, Sandy J. Schexnailder, Carl Urban

At the Schwartzwalder Mine (Cotter Corporation, Golden, Colorado) ion exchange resins have been used in mine water treatment experiments. The experiments, initiated in October 1979 and currently in progress, demonstrate that mine water uranium values can be reduced to levels as low as 10 ppb. Duolite® A-101D, a strongly basic anion exchange resin, was tested in laboratory-scale columns (1 inch diameter) initially and then in pilot-scale columns (4 inch diameter), using both co-current and counter-current operational modes. Observations and conclusions resulting from these studies can be summarized as follows: (1) Duolite® A-101D appears to have successfully extracted uranium at influent levels of approximately 2.0 ppm over multiple loading and elution cycles, consistently producing effluent concentrations as low as 10 ppb uranium. (2) Based upon present test data, counter-current regeneration appears to be the key to successful operation. Upflow loading and downflow elution are the preferred modes for service and regeneration, respectively. (3) Filtration is a necessary pretreatment to remove fine clay and inorganic precipitates that will foul the resin, causing excessive pressure drop and poor loading and elution kinetics. (4) This waste treatment application is unique in that it offers the opportunity to recover some or all of the capital investment in the treatment facility

Jan 1, 1980

By D. C. Ridenour

The pressure system of ventilation with large diameter bore holes has been very effective in the ventilation of two gaseous mines, the Olga No. 1 and No. 2 Mines in McDowell County, West Virginia. The No. 4 Pocahontas Coal Seam on the Olga property lies 580 feet below the valleys. The seam is very gaseous as well as dry and dusty, which makes good ventilation all the more essential. Irregular and often extensive areas of the coal seam have been replaced with impervious shales and sandstones in "Fault" or "Want" areas. The replacement materials have sealed the methane in the coal seam and thus increased the quantity of gas that must be handled as mining is done. Often the No. 5 Pocahontas Seam comes down to meet the No. 4 Seam at the Faults and considerable methane is sometimes released from the upper seam. The factors mentioned, together with the irregular and unpredictable lateral shape' of the faults, result in long narrow stringers of coal that are very gaseous and difficult to mine. So far as the Olga Coal Company is concerned, the most effective ventilation under the conditions outlined has been the use of large diameter bore holes with a pressure ventilation system. The ventilation of a mine can be accomplished in two fundamental ways. The mine atmosphere maybe reduced below atmospheric pressure by an exhaust fan; or it may be raised above atmospheric pressure by a pressure fan. In either case, the coursing of the air is so planned as to have the haulage and traveling ways on intake air. While the majority of the coal mines in the United States, no doubt, use the exhaust system of ventilation, there are several advantages of the pressure system which are extremely beneficial.

Jan 1, 1960

By D. Malhotra

Most primary-molybdenite producers use a selective-flotation process in which molybdenite is floated from the ore while other sulfide and non-sulfide gangue minerals are depressed in the same step (Figure 1). The process was developed at the Climax mill. Reagents used in the rougher-flotation stage include vapor oil (collector), syntex (surfactant), pine oil (frother) and occasionally sodium cyanide and Nokes reagent (depressant). Rougher concentrate is upgraded by cleaner flotation to produce market-grade molybdenite concentrates. Reagents used in the cleaner flotation stage are Dowfroth 250, vapor oil, sodium cyanide and Nokes reagent. The development of the flotation reagent scheme at Climax and the role of the reagents have been well described by Born, et al, (1976) and Malhotra, et al, (1976, 1977a, 1977b, 1977c, 1980). The hydrocarbon collector, vapor oil, accounts for approximately 50 percent of the total molybdenite-flotation reagent cost. Because vapor oil sources are limited, and the cost of vapor oil has increased significantly over the last decade, several studies have been done to evaluate alternate oil-based collectors and/or blends of collectors which would produce similar metallurgical results at a reduced cost, or increase the overall molybdenite recovery at the same cost (Smit and Bhasin, 1983; Hahn, 1969; Smith and Bhappu, 1971). The approach taken in the present study was to evaluate alternate non-oil based collectors and collector systems that are less expensive than vapor oil.

Jan 1, 1985

By R. W. Henn

Introduction Shotcrete, by the American Concrete Institute definition, is mortar or concrete pneumatically projected at high velocity onto a surface. The term gunite is still common in literature. It is a trade name established by Cement Gun Co. of Allentown, PA, around 1911 for a dry mix of fine aggregate material, hydrated at the nozzle, and pneumatically projected at high velocity onto a surface. This article will discuss shotcrete applications, ingredients, mix proportioning, batching and mixing, admixtures, testing, and steel fiber vs. conventional shotcrete. Applications Shotcrete is used primarily by the mining and underground construction industries to temporarily stabilize an excavated rock surface until a permanent cover can be installed. It may also be used as the permanent covering material. Other uses include refractory material, architectural finishes, slope stability, wearing surfaces, repairing existing concrete structures, fireproofing, and corrosion protection of steel. Wet Versus Dry Process In the wet process, all ingredients, including water but not accelerator, are mixed the same way as normal concrete before its placement by pneumatic projection. The accelerator is added in a liquid state through the nozzle at the point of placement. In the dry process, all ingredients, including acceleration in dry form but not water, are mixed just before placement by pneumatic projection. Water is added through the nozzle at the point of placement. Liquid accelerator may be added at the nozzle in the dry process. Ingredients Shotcrete consists basically of the same ingredients as concrete with some limitations. Type I, II, and III cements are used. However, Type II seems to be used most in underground applications. This can be attributed to ground water at most sites having slight to moderate concentrations of sulfates. Air-entraining cement or air-entraining admixtures are generally not used in dry mix shotcrete. It is generally agreed that it is impossible to entrain air due to the absence of the usual concrete mixing action, and the high velocity of impingement of the material on the application surface. Air-entraining cement or air-entraining admixtures are used in wet mix shotcrete. Their use, however, is not widespread due to the placement method and the fact that high velocity air drives off most of the entrained air. Test results are not conclusive in showing any durability increase of shotcrete to freezing and thawing by using entrained air. In spite of current practice, the trend is toward additional research, with more agencies and owners requiring the use of entrained air. The philosophy behind this is that some entrained air is better than no entrained air to increase durability to freezing and thawing. The aggregates used in shotcrete are the same as those used in concrete. However, the largest coarse aggregate presently used is 19 mm (0.75 in.). A typical gradation requirement is shown in Table 1. The water quality requirement for shotcrete is the same as that for concrete. Accelerators are by far the most important admixture in shotcrete.

Jan 6, 1984

By G. M. Matheson

Mining in the Colorado Springs coal field took place from the 1880's to 1940's. The depth of mining in the coal field varied from about 10 meters to over 150 meters. Review of sequential historical aerial photographs from 1937 to 1960 indicated about 2400 chimney subsidence sinkholes had developed throughout the study area. Statistical analyses of the location and size of these sinkholes with respect to the time since mining, depth of mining, mined thickness and type of mining indicated definite trends in the time of occurrence, size, and location of these features. This data is valuable in the assessment of potential future subsidence in this and other areas of similar mining conditions.

Jan 1, 1985

By Keith G. Papke

Industrial-mineral mining started early in the history of the State when salt was extensively mined for use in processing gold and silver ores, and borates were produced to meet most of the world's needs. After this start, industrial-mineral production grew slowly until World War II, mostly because of the remoteness of the State and the small population. Nevada now has a large and varied industrial-mineral industry. In 1983, 14 principal commodities were produced from 48 deposits; the total value of these materials was 168 million dollars. Nevada ranks first in domestic production of barite and magnesite; second in diatomite, gem stones, and lithium; third in fluorspar; and sixth in gypsum. Other materials produced are carbonate rocks, cement, clays, decorative and crushed stone, light- weight aggregate, perlite, pyritic soil additive, salt, sand and gravel, and silica. From 1978 through 1982 barite was the most important commodity; in 1983 diatomite surpassed barite in value of production. Most of the Nevada production consists of high-value commodities that are consumed out of the State. Approximately 430 significant deposits with 20 principal commodities are present in Nevada. This abundance can be attributed to the numerous and diverse geologic processes that have been operative. Seven major modes of origin have been identified: hydrothermal activity, sedimentation, combined hydrothermal activity-sedimentation, evaporative precipitation, brine formation, extrusion of igneous rocks, and alteration by ground water. The hydrothermal type accounted for 39 percent of the deposits, the combined hydrothermal-sedimentary type for 28 percent, and the sedimentary type for 13 percent. Nevada diatomite production is about 200,000 short tons/year valued at 30 million dollars. In 1984 three companies operated in Nevada producing diatomite from six open pits and processing it at four plants - one plant producing filter-grade materials and the others adsorbents and fillers. The diatomite occurs in about 60 areas, almost all in the western one-third of the State. The diatomites were deposited in long-lasting, fresh-water lakes in topographically closed valleys formed by basin-and-range faulting. About 85 percent of the barite mined in the United States is produced in Nevada. In 1981 the high point of production,-2.5 million short tons of bedded barite was produced from about 30 open-pit mines. About 120 significant bedded-barite deposits are known in Nevada; 38 of these have had past production of more than 25,000 short tons. The deposits are associated with marine siliceous rocks of Cambrian through Devonian age and occur in a zone about 300 miles long and 60 miles wide. Abundant evidence supports the theory that the bedded barite is of exhalative sedimentary origin.

Jan 1, 1987

By Francesco Chiappalone, Marco Invernizzi, Franco Gasperin, Fabrizio Fara

As part of the Ship Canal Water Quality Project, 2.7-mile Combined Sewer Overflow tunnel is excavated with a 21.5-foot diameter EPB Tunnel Boring Machine. Due to the difficult geological and hydrogeological conditions, the tunnel is excavated maintaining a ground support pressure between 1 and 3 bar imposing significant challenges to the projects. The first part of the paper describes the general characteristics of the project while the second part focuses on the challenges and technical details of the pressurized breakthrough that took place in a deep shaft excavated in urban environment as part of the project.

Jun 23, 2024