Search Documents

By Brain W. Lawrence

Sublevel stoping generally is a large-scale open stoping method. It sometimes is referred to as long-hole or blasthole stoping. This method usually is applied to strong ore bodies that require minimal support and are surrounded by strong country rock. The ore body should be fairly regular in shape and well-defined. The dip of the footwall normally should be sufficient to allow broken ore to gravitate freely, although the method has been adapted successfully to mine some of the flatter ore bodies. Sublevel stoping is not dependent on the width of the ore body. Widths of less than 6 m (20 ft), however, make the utilization of long-hole drilling techniques more difficult. The main criteria for sublevel open stoping are competent ore and stable host rock, regular ore boundaries, and a footwall dip that exceeds the angle of repose of broken ore. Basically, the method entails providing access to the ore body at various subintervals between the main haul- age levels in order to drill and blast the intervening ore. Stope drilling is carried out from drilling drifts on the sublevels, and the ore is blasted in slices towards an open face, which generally is vertical on the downholes and may be inclined towards the open face for the up holes. The blasted ore gravitates to the bottom of the stope and is collqcted through drawpoints. Fig. 1 illustrates a typical sublevel stoping mine. The method requires extensive ore body development with relatively high capital expenditures. How- ever, much of the development is in ore, and production costs are comparatively low. Productivity rates are in the 13.6 to 27.2 t (15 to 30 st)/manshift range. The drilling, blasting, and loading operations are performed independently, and equipment utilization is high. Large outputs can be obtained with few units and limited personnel. Dilution with waste rock may occur if ore boundaries are irregular or if caving occurs, but 100% of the ore within the stope usually is recovered. Pillar recovery sometimes is a problem. It is at this point that most of the waste dilution occurs. At the time data was gathered for this report (1973), the sublevel open stoping method was used by more than 21% of the metallic ore mines in the US (9 out of 42 mines producing 1088 + t/day (1200 + stpd) and provided more than 12% of the total metallic ore production from these mines. DEVELOPMENT Access to a sublevel open stope mine is gained by a slope or shaft that is normally sunk in the footwall of the ore zone, away from any possible effects from blasting or other production operations in the stoping process. Main level interval is selected and usually varies from 45.7 to 121.9 m (150 to 400 ft), depending on the vertical extent of the ore body, the number of drawpoints required to maintain output, and the eventual stope height. The main haulage drifts are located at the bottom of the stope horizon, either directly in ore or in the footwall, with access crosscuts at intervals. Raises are driven up through the ore to connect to the level above and provide access and ventilation to the sublevel drilling drifts, which are driven horizontally in the ore for the length of the stope. Depending on the drawpoint system to be used, the stope is either undercut by a raise-and-cone system, from a scram or slusher drift, or simply provided with a drilling drift from which access is made at intervals to the main haulage level. A raise driven either at the end or in the middle of the stope (if stope access is from both ends) provides a start for opening up a vertical slot across the stope to establish a free or open face for long-hole drilling and blasting. Sublevel stoping has proved to be a relatively safe and economical system.

Jan 1, 1982

By Erich Sarapuu

Today's increasing needs for rapid excavation have stimulated efforts to break rocks without explosives. The application of electric energy for this purpose has been studied by a number of investigators. Following principles have been used in electrical rock breaking: 1. induction heating5 2. high frequency heating4, 14 3. microwave heating6 4. contact resistance heating9,12 5. resistance heating11,13 6. electron beam heating1, 3 7. plasma jet heating2, 8 8. arc heating7 9. condensor discharge energy14 In this paper the presentation of the principles of electrical fragmentation is limited to a process called "electrofracing". This technique uses electrical heating of rock by electrode contact resistance9 and resistance heating" phenomena. The electrically induced stresses inside of rock generate forces which break up the material. The fracturing of ore takes place by tensile stresses instead of compressive forces. The electric energy merely creates fractures in the rock and the separation of fractured material takes place by subsequent mechanical handling. Energy requirements in secondary breaking of iron ores have been about one to two kilowatt-hours per ton of ore. Power requirement is a function of the degree of fragmentation.

Jan 1, 1969

By David A. Holmes

Zeolites are crystalline, hydrated aluminosilicates of the alkali and alkaline-earth metals. Their crystalline framework is based on a three dimensional network of SiO4 tetrahedra with all four oxygens shared by adjacent tetrahedra. The alkali and alkaline-earth cations are loosely bound within this framework structure and may be exchanged, to varying degrees, with other cations or molecular water. Most zeolites can be reversibly dehydrated. At present, close to 40 natural zeolite minerals have been identified and over 100 zeolites have been synthesized. Zeolites are a family of hydrous aluminosilicate minerals whose physical properties provide unique features for a wide variety of practical applications. Zeolites have been known for more than 200 years, but it was not until the middle of this century that their economic potential and widespread occurrence in sedimentary rocks were known. Since 1950, literally thousands of articles and patents have appeared in technical literature, and commercial pro¬duction of natural zeolites may now exceed 1 Mt worldwide an¬nually. In the past 40 years, the zeolite mineral group has changed from that of a museum curiosity to one of an established industrial mineral commodity. According to Breck (1974), zeolites are characterized by the following properties: 1) High degree of hydration, 2) Low density and large void volume when dehydrated, 3) Stability of the crystal structure of many zeolites when dehydrated, 4) Cation exchange properties, 5) Uniform molecular-sized channels in the dehydrated crys¬tals, 6) Ability to adsorb gases and vapors, 7) Catalytic properties. All zeolites are molecular sieves, but not all molecular sieves are zeolites. Activated carbon, activated clays, alumina powder, and silica gels are also molecular sieves. Molecular sieves are materials that can selectively adsorb molecules on the basis of their size, shape, or electrical charge (Clifton, 1987). Commercial application of zeolites is based on the following physical properties: molecular sieving, ion exchange, adsorption, and catalysis. Potential commercial utilization includes hundreds of possible applications. The principal uses at this time, however, are as fol¬lows: -Ammonium-ion removal in waste stream treatment, sewage treat¬ment, pet litter, and aquaculture, -Odor control, -Heavy metal ion removal from nuclear, mine and industrial wastes, -Agricultural use, such as soil conditioner and animal feed supplement. An estimated 800 kt to 1 Mt of natural zeolites were produced and consumed worldwide in 1991. Eight small operators reported collective production and consumption of an estimated 18 kt of natural zeolites in the United States during 1991, mostly for feed additives and for odor control, aquacultural, agricultural, catalytic, and ion exchange applications (Eyde, 1992).

Jan 1, 1994

By III Feeley

The U.S. Department of Energy is supporting the engineering development of three advanced physical coal cleaning technologies--selective agglomeration, advanced flotation, and advanced cycloning--capable of significantly reducing the pyritic-sulfur content of U. S. coals. The objective of this activity is to provide the coal production and electric-utility industries with a cost-effective option for addressing the SO2 emission reductions required by the 1990 Clean Air Act Amendments. A secondary objective is to evaluate the potential of advanced coal cleaning for removing trace elements that are precursors to the formation of hazardous air pollutants. This paper will summarize the status of the three advanced physical coal cleaning engineering development projects.

Jan 1, 1993

By W. M. Aubrey

The use of solid fuel in shaft furnaces to indurate iron ore pellets was originally considered a necessary evil, which the industry worked long and hard to eliminate. Since then changes have taken place in furnace design and operating practices that have led us to our suggestion that solid fuel additions could again be used. In essence, what has happened is that the developments which made it possible to operate without solid fuel have also created new operating conditions favorable to the effective use of solid fuel. Because these new conditions* were brought about in part by the desire to eliminate solid fuel and because the development was a gradual one, the industry failed to reassess its position and for years neglected the possibility of returning to solid fuel.

Jan 1, 1967

By Patricio A. Espinoza, Aldo Casali, Cristian Ardiles, Guillermo González

Cluster analysis is used to design grade soft-sensors in a rougher flotation plant and a ball mill overload soft-sensor. Soft-sensors are virtual sensors which either replace unavailable actual sensors or infer measurements for non existing sensors. In the case of the grade soft-sensors clustering serves to determine clusters of related operating points. To each cluster there corresponds an ARMAX model structure whose parameters are estimated using only the points in the corresponding cluster. Thus a much better correlation is found than if all the data points were used for a global model. The problem of identifying clusters when the measurement of the real sensor is not available is addressed. In the case of the overload soft-sensor, variables were selected which are related to overload, either from a phenomenological point of view or according to operator experience. Different clusters are formed, some of which are identified as determining an overload condition or a possibility of such condition. Each of these clusters has a set of operating conditions which suggests the corrective action to be taken when necessary. Both kinds of soft-sensors are tested with industrial plant data and promising preliminary results are obtained.

Jan 1, 1995

By Jean Dupere

Mr. Chairman, Ladies and Gentlemen, I'd like to take just a moment of your time before we examine the current position of the asbestos industry and its market outlook to take a searching look at the product itself. I feel that if we are to understand the problems that beset this basic mining and manufacturing industry and, more important, if we are to appreciate the solutions to these problems that I plan to put forward in a few moments' time, then we had better look at asbestos from the proper perspective. Asbestos has a unique combination of properties - properties not found in any other natural substance or man-made material. This has resulted in asbestos finding its way - in fact, being welcomed - into literally hundreds of applications.

Jan 1, 1984

By R. R. Klimpel

This paper demonstrates, using the results of an unusually complete industrial test sequence, what the various interactions are between grind size, collector dosage, and frother type. While particle size is universally acknowledged to be important in optimizing industrial copper sulfide rougher flotation circuits, many of the various interactions that do occur at the industrial level with particle size are still being identified and/or quantified. This study also presents, in a consistent manner, the changes in flotation kinetics that occur as a function of particle size, in a typical industrial circuit along with some insights as to how flotation operators can optimize rougher circuit performance.

Jan 1, 1993

By John B. Goddard

The discovery of rhenium on the ion exchange resin used at the uranium in-situ leach operations at Palangana (Texas) led to a laboratory study on the possible methods of recovery. Rhenium, present in small amounts in the ammonium carbonate leach liquors as the perrhenate anion, Re04-, concentrated on the anion exchange resin, which was a factor of ten more selective for rhenium than for uranium. Various elution systems were investigated for stripping the rhenium from the columns after the uranium had been eluted with chloride or nitrate solutions. Although the perchlorate ion was most efficient on a molar basis, nitrate ion combined the benefits of efficiency and low cost. A 3[N] or stronger concentration of nitrate containing up to 0.5[N] H+ was found to be the system of choice. A rhenium sulfide concentrate containing up to 14% Re was obtained from these effluents by hydrogen sulfide precipitation. Preliminary experiments were run to produce rhenium metal powder by oxidation of the concentrate to NH4Re04 followed by hydrogen reduction at elevated temperature.

Jan 1, 1982

By Otto Schumacher

Shortcut methods are commonly employed for estimating mining costs for prefeasibility studies. Most of these methods, however, are suitable for earliest stage studies or for internal discussion purposes only. The experts at InfoMine?s CostMine division recommend that any cost estimate completed for purposes of significant decisionmaking or for compliance with Canada?s NI 43-101 requirements be completed using a determinative itemized method. The same basic principles apply for an early stage, intermediate stage, or advanced stage estimate. The only difference is in the level of detail and effort employed. ? Based on the results of a completed resource estimate, an itemized cost estimate begins with development of a conceptual mine plan. Using a surface mine as an example, four elements are crucial no matter what level of study is initiated. Basic geometry of the ore deposit and waste material, with a determination of the expected ratio of waste to ore, a reasonable pit slope angle, possibly requiring the completion of geotechnical studies to predict the waste-to-ore ratio with certainty. ? Determination of the assumed ore and waste production rates. ? Locations of all ore stockpiles and waste dumps. ? Segmental haulage distances and gradients for ore and waste.

Oct 1, 2013

By C. J. Monahan

INTRODUCTION With the introduction of large diameter hole drilling to underground mining, a need for the development and utilization of new blasting technology has arisen. This new technology has resulted in more efficient blasting and in easier and cheaper mining. The application of spherical charges to the crater blasting method is an im¬portant part of this technology. Spherical charges, or their geometric equivalent, make for highly efficient use of explosives in the cratering application. Their geo¬metrical configuration, normally a length :diameter ra¬tio of <6:1, limits their charge weight size. For exam¬ple in a 165-mm (61/2-in.) hole a spherical charge weighs approximately 34 kg (75 lb). These dimensional and weight restrictions require careful engineering design and control in the production application. Strathcona mine, a large tonnage mechanized cut¬and-fill and blasthole stoping operation located on the north rim of the Sudbury Basin, has successfully em¬ployed the crater blasting method in production blasting for the past two and a half years (as of 1979). As a result, this method, using spherical charges, has made possible the development and implementation of a verti¬cal retreat blasthole mining method which is being used for rib pillar recovery. The crater method used at Strathcona essentially in¬volves blasting off horizontal slices of ore into an under¬cut while retreating vertically to the pillar overcut elevation. Loading and priming of the holes is achieved from the overcut and the blasted muck is recovered by load¬haul-dump (LHD) units through a drawpoint system. Valuable experience on the behavior and performance of explosives in large diameter holes has been gained in both the operating and engineering fields from the appli¬cation of this blasting method. It has been used in drop raising and is currently being evaluated for use in pri¬mary stoping operations. Also, serious consideration is being given to its use for the recovery of post pillars in mined-out and backfilled cut and fill stopes. The method has significant advantages over conven¬tional methods of pillar recovery from economic, ground control, and safety points of view. These include cost benefits due to a minimum stoping development, less ground support, reduced labor requirements, and faster mining rate. Research on the blasting mechanism indi¬cated the method should result in less damage to fill walls than would be normally expected with conven¬tional longhole or large diameter hole cylindrical blast¬ing (benching). This is primarily due to the limited charge weight per delay because of the size dimensions of a spherical as compared with a cylindrical charge and also because the large diameter holes experience less de¬viation than standard-sized longholes. Experience has shown that wall damage has been minimized with the use of this method. The safety aspects of the working environment are also improved as there is no require¬ment for manpower to go under exposed backs after blasting, which is a significant improvement over the cut-and-fill method. CRATERING THEORY General The term cratering, in blasting, is applied to the for¬mation of a surface cavity in a material as the result of detonating an explosive charge in that material. This blasting concept was initially used as a tool in the eval¬uation of explosives performance; however, it has been utilized more recently on surface and to a lesser extent in underground blasting operations. Explosive charges used in crater method are nor¬mally spherical or the geometric equivalent, as research into the application of this breakage mechanism to rock indicates that spherical charges or their equivalent pro¬duce optimum results. In blasting practice, spherical charges have been defined as having a length to diameter (L: D) ratio of 4:1 or less, and up to, but not exceeding a L: D = 6:1. Thus, for holes 165 mm (61/2 in.) diam, a charge 165 mm (61/2 in.) diam, and 990 mm (39 in.) in length would constitute a spherical charge. Crater Testing Crater testing for underground application is nor¬mally accomplished by drilling smaller than production sized horizontal holes into drift walls, placing relatively small charges of explosives in the holes at various depths of burial, firing the charges, and measuring the results. The results are scaled to develop charge weight size and depth of burial parameters for production hole sizes. In theory, this procedure is valid and is appli¬cable for surface blasting; however, in underground applications where the craters are inverted, there is some question as to whether extrapolation of the test results is appropriate. As well as the fact that craters are in¬verted with resultant gravity stresses, testing is often done in a waste rock drift where the properties differ from those in ore rock. There is also some question as to whether a 51 or 76-mm (2 or 3-in.) diam charge behaves similarly to a 165-mm (61/2-in.) charge in a confined borehole. Crater testing at Strathcona involved drilling 76-mm (3-in.) diam holes at various depths ranging from 1 to 3 m (3 to 10 ft). The test holes were drilled in the wall of a predominately waste drift as well as in a stope wall. Charges were placed at various depths of burial, were confined, fired, and the results measured. Although the results were somewhat erratic, possibly because of the aforementioned reasons, they did provide guidelines for basic design for production application. MINING METHOD APPLICATION FOR PILLAR RECOVERY Following initial crater testing, assessment, and tech¬nical evaluation, it was decided to use this blasting tech¬nique in a production application, and to incorporate

Jan 1, 1982

By M. A. Rodrigues da Silva Enríquez

One of the rare consensual points among different resource-based economic analytical approaches refers to the strategic role of rent from mineral extraction, as a decisive tool to ensure that the temporary wealth generated in the present can turn into permanent income in the future. For this reason, evaluation, distribution and use of mining rent plays a central role in the sustainable development of mining cities. Brazilian legislation provides for this at the municipal level by means of participation in the financial results of mineral extraction accomplished in these municipalities, with the Financial Compensation for Mineral Exploration (CFEM). CFEM is a type of ad valorem royalty, which charges taxes of up to 3% of the net revenue of mineral production. However, legislation does not establish how these resources should be used. Therefore, there is wide variation in the use of CFEM income among Brazilian mining cities. A study from a sample of the 15 largest mining cities in eight Brazilian states made possible identification of two main patterns with regards to the use of CFEM which were labeled "sustained use" and " the pitfall of the single treasury." In that regard, this article discusses the pressuring factors that contribute to these patterns, as well as the institutional arrangements which may be more favorable to inducing more sustained use of CFEM.

Jan 1, 2011

By R. F. Davis

The evaluation and selection of coals for producing metallurgical coke is indeed a com- plex process simply because coal is a complex and variable substance which is sensitive to how it is treated from the time it is mined until it is transformed into coke. A review of the the more common evaluation tests made on coal and how the test results are applied in commercial practice. Parameters used to select coal blends for wet and preheated charges should also be of interest.

Jan 1, 1980

By B. A. Ferguson, P. W. MacMillan

INTRODUCTION Jack Spalding in Deep Mining, Chapter 3, states: "In deep mining, to start stoping an orebody without a definite plan of operations covering the whole extraction from beginning to end is to invite serious trouble. Any stoping without plan is bound to leave, toward the end, a number of pillars, remnants, or promontories, which, as they are reduced in size, are liable to fail and cause a general collapse. The object of stope planning is so to mine an orebody that at no stage in the operation is a remnant left. Definition: `When a block of ore is stoped in such a way that eventually a small piece is left entirely surrounded by stoping, that piece is termed an island remnant.&apos; The design of and adherence to a plan of stoping is of greater importance in preventing rock bursts than the type of ground control adopted." This, of course, is just an example of the old axiom that an ounce of prevention is worth a pound of cure. And in this context, mining does not have to be very deep before poor ground conditions, made worse by lack of good planning, force a mining company to resort to more expensive methods of ore recovery. At all times when rock pressures become excessive, stoping plans must be devised to avoid the creation of pillars or promontories. This is most readily recognized when mining deep narrow ore veins by open methods. It would be a little more general to say that stoping systems should seek to avoid or minimize localized concentrations of rock stress. Ore bodies, and particularly those at Falcon¬bridge, can reach large widths and leaving pillars for extraction at a later time cannot be avoided. However, good planning can reduce the effect of factors which create bad ground conditions. The necessary ingredients of planning are time and information: time to formulate and revise ideas; information, gained in exploration and early development, to provide the fullest knowledge of the ore body. In this way, plans become meaningful. It must always be kept in mind that the long-term results of good planning often require decisions not compatible with reaching earliest full production. PLANNING FOR DEEP MINING At Falconbridge Nickel Mines ore bodies presently being found and prepared for production lie at depths in excess of 610 m (2000 ft) below surface. Current un¬derground exploration is being directed towards favor¬able locations below 914.4 and 1219.2-m (3000 and 4000-ft) depths, at most mines. The Onaping Deep ore body has been traced to a depth of 1508.8 m (4950 ft) and at Falconbridge mine the ore body is under develop¬ment below the 5000 level. Planning for more efficient ground control has therefore become an important con¬sideration of future mining. HYDRAULIC BACK FILLING AND CUT-AND-FILL STOPING The advent of hydraulic back filling has led to the increasing use of flat-back cut-and-fill stoping methods during the last ten years, until it has probably become the commonest method of mining deep ore deposits in Canada. These methods account for almost all the pro¬duction from Falconbridge Mines at this time. The ad¬vantages claimed are: safety-a minimum of open ground; very little supplementary ground support (except rockbolted backs and walls); greater selectivity and flexibility in extraction (horizontal extension of the vein, high grade ore stringers going out into the walls); and high productivity and increased mechanization in larger ore widths. There is some difference of opinion as to whether hydraulic classified tailing back fill provides any great resistance to initial closure of the stope walls. The evi¬dence available suggests that it does not. Addition of portland cement to the back fill just prior to placement has produced a material having the properties of a weak concrete. It is confidently expected that this material will assist greatly in the efficient mining of pillars and generally in giving increased ground support to oppose closure. PRINCIPLES OF STOPE PLANNING BY LONGITUDINAL FLAT-BACK CUT-AND-FILL Again quoting from Spalding: "The practice of con¬trolling output by stopping and starting stopes is bad¬stopes once started should proceed without interruption, and control must therefore be obtained by altering the rate of stoping. It is therefore necessary that faces should normally advance at a medium rate which can be boosted, if required, to give temporarily a greater output. Modern high productivity stoping methods, however, generally aim to achieve and maintain the maximum output possible from a stope. Control of tonnage and grade, therefore, becomes a more complex problem requiring very careful scheduling and organiza¬tion. With the basic method of flat-back overhand stoping using hydraulic fill, it is not usually possible to mine in such a way as to avoid creating pillars." Consider an ore body as illustrated in Fig. 1. It is 274.3 m (900 ft) high by 228.6 m (750 ft) long on strike and averages 4.6 m (15 ft) in ore width. It rep¬resents approximately 907 000 t (1,000,000 st). The ore body could be mined by advancing one long single face through all the levels from bottom to top. A total face length of 228.6 m (750 ft) would accommo¬date five 45.7-m (150-ft) stopes. See Fig. la. Each of these stopes would produce approximately 1814 t/m (2000 stpm) and the ore body would require a period of ten years for complete extraction. A possible im¬provement to this scheme might be to stagger the indi¬vidual stope faces. See Fig. 1b. Problems of hanging wall failure can be reduced by this arrangement. From the point of view of reducing travelway maintenance, it is good practice to employ a stoping system of retreat. Stopes farthest from the shaft are mined first so that on completion, haulage drifts below can be aban

Jan 1, 1982

By R. R. Klimpel

The grinding of coal-water slurries has received increasing industrial attention during the last decade. In particular, there is long-term interest in the use of pulverized coal-water slurries to replace oil in combustion equipment and the development of coal gasification/liquefaction processes which require coal-water slurries as feed. More specifically, the use of coal-water slurries in gasification requires grinding a high density slurry containing the smallest amount of water consistent with slurry pumping and spraying. As part of a fundamental engineering research support program aimed at the industrial implementation of dense coal-water slurry grinding, this author has published several papers on how specific rates of breakage vary as a function of slurry rheology, Klimpel (1982, 1982/83). These papers demonstrated that there is a consistent pattern of change in specific rates of breakage of coal in dense slurries with controlled variations in slurry rheology. By matching rheological data with laboratory grinding results, it was possible to identify directly slurry conditions that correspond to: (1) slowing down of breakage rates, (2) the occasional acceleration of breakage of some sizes, and (3) conditions where chemical additives will increase rates of breakage.

Jan 1, 1990

By G. W. Luxbacher

Coal mine infrastructure is rarely designed solely on the basis of ventilating the underground workings. Instead the optimization of a mining sequence, the minimization of coal quality variation, reduction of coal losses by adapting to property boundaries and geologic structure (seam inclination, roof conditions, coal thickness, etc.) or other similar considerations have formed the objective for mine plant design and layout. Infrastructure development may also reflect a desire to maximize production early in the life of the mine or to permit flexibility in mining according to market conditions. Requirements for coal mine ventilation, established by the 1969 Coal Mine Health and Safety Act, have mandated changes in the traditional concepts of mine plant design in the United States. Mines, in operation prior to the passage of the Act have experienced severe limitations when attempting to adapt the existing mine infrastructure to meet the requirements of the law. In addition the increased quantities of air required, velocity limitations on trolley haulage and belt lines, the establishment of separate intake escapeways and gob area ventilation have com- pounded the inherent complexity in planning mine ventilation systems. Past practices in mine ventilation planning and design are no longer adequate. Given the complexity of today&apos;s ventilation systems, effective planning and design approaches are required. As such, the interrelationship between the overall coal mine plant design and ventilation system design is examined. An approach to ventilation system design constrained by global considerations of mine plant design, is presented. The proposed approach is, however, applicable to the design of new mine ventilation systems as well as to the modification of existing systems.

Jan 1, 1980

Capital budgeting and investment analysis have, to this point, been beyond the scope of this text. However, a recent conceptual development by John K. Shank and Vijay Govindarajan in the capital budgeting literature is of interest to operations managers because it (1) employs some of the cost management tools outlined earlier in this text and (2) provides a useful framework for using cost management techniques to improve the competitive position of the firm. ft Shank and Govindarajan present a method of analyzing proposed expenditures that is not based on discounted cash flow measures. Their approach employs a combination of three analytical tools: value chain analysis, strategic positioning analysis, and cost driver analysis. In each of these, cost and revenue information is used in ways normally not associated with conventional budgeting. Using this framework, capital projects are selected based on their ability to improve the firm&apos;s strategic position. Shank and Govindarajan have termed this approach "strategic cost management."

Jan 1, 1999

By W. E. Benton

Diatomite or diatomaceous earth is a siliceous sedimentary rock principally made up of the skeletal remains of the diatom, a microscopic, single-cell aquatic plant related to algae. The unique structure, chemical stability and physical properties are the major attributes of diatomite not met by other forms of silica. The production of diatomite was down in 1982 vs. 1981, reflecting the worldwide recession. The principal markets for diatomite products continue to be basically filtration and fillers. The outlook is for small but steady growth into the 1990s.

Jan 1, 1983

By Keith G. Wallace, Oscar Codoceo

This paper describes the ventilation planning that was per- formed at the Barrick Gold Corporation, El lndio Mine. The El lndio Mine is located at an elevation of approximately 4,000 m in the Andes mountains east of the coastal city of La Serena, Chile. The ventilation planning program consisted of a detailed ventilation survey of the mine and the establishment of a correlated com- puter model. A series of network simulations were conducted to determine the optimum position, size, and configuration of new ventilation raises and main fan exhaust system. Modifications to existing mine infrastructure including; driving of drifts, slashing of airways, and positioning of ventilation controls were examined. Detailed costing information was developed to optimize the location of the new main exhaust raises and fan system. The final ventilation system is expected to increase the mine airflow from the existing 157 m=/s to over 315 mls. This increase was necessary to accommodate an expansion in mine production, diesel equipment utilization, and deeper mine development. Furthermore, the increased airflow was required because of the de-rating of diesel equipment and large air volumes necessary to dilute diesel exhaust at high elevation.

Jan 1, 1997

By Olivia Perkins, Shawn Sismondi, Adrian St. John, Vicky Potts

"INTRODUCTION An inherent aspect of any tunnelling project is ground risk: how it is identified, quantified and managed throughout the various stages of a project. Early identification of these risks, such as adverse ground conditions or potential obstructions is crucial; however specific identification of all risks will inevitably be limited by the extent of the desk study, ground investigation and accuracy of as-built information available, particularly in a densely populated urban environment such as London with a long and varied history of development. It is therefore crucial to have suitable plans and procedures in place for dealing with potential ground risk scenarios if they occur during construction work to ensure the safety of the workforce and to protect nearby critical assets. A number of experiences of potential ground risk were encountered during the Sprayed Concrete Lining (SCL) works on Crossrail contract C300/410 which was constructed by a joint venture of BAM Ferrovial Kier (BFK). The C300/410 works, undertaken in the heart of London, comprised of over 2.5km of SCL tunnels for Bond Street and Tottenham Court Road Stations and the Fisher Street crossover, as well as two 6.2km TBM tunnel drives between Royal Oak and Farringdon. BFK appointed Donaldson Associates as their SCL designers for the works; together they were responsible for excavation stability up to the point of ring closure. Despite the majority of SCL tunnelling works at Bond Street and Tottenham Court Road being through the favourable medium of London clay, there remained areas of local geotechnical challenges. Some of these were expected from the outset, some became apparent as works progressed from records of other nearby excavation works, and some were only encountered during tunnel excavation. Being located in the centre of London meant that there always remained a possibility of meeting some form of obstruction from previous structures. However, identification of all potential issues prior to the commencement of the works was challenging and proved to not be entirely possible. Through a series of case studies, this paper documents incidents where obstructions or adverse ground conditions arose. These scenarios all had the potential to cause safety risks, impact the tunnel design and/or construction methods and ultimately add time and cost to the works. The paper discusses how these challenges were overcome which utilised in part, a progressive risk reduction cycle, feeding back knowledge gained at all stages of construction into the approach for undertaking the works. It also examines what could be done in future to further reduce the ground risk through early identification, communication, education and appropriate contingency measures."

Jan 1, 2016