Search Documents

By John F. MacDonald, John W. Critchfield

This paper describes the shield excavation of twin transit tunnels, through soft ground, in downtown Seattle. The tunnels are 6.5 m (21.25 ft) diameter and 1525 m (5000 ft) long. Initial support consisted of expandable precast concrete segments, followed by a final lining of cast-in-place concrete. Waterproofing was provided by a PVC membrane installed between the initial support and the final lining. During the course of the excavation a variety of methods were used to control the ground and limit settlement. These included deep wells, vacuum well points, eductor wells, chemical grouting, compaction grouting, jet-grout underpinning, and extensive instrumentation.

Jan 1, 1989

By Y. Lv, H. Ye, D. Du

Electrolytic manganese residue (EMR) is a kind of industrial solid waste with high silicon content that contains harmful metal elements such as chromium (Cr), copper (Cu), lead (Pb), cadmium (Cd), nickel (Ni) and cobalt (Co). Developing a highly effective and environmentally friendly process to treat EMR is important, both for the reutilization of metal resources and for environmental sustainability. In this study, the bioleaching of available silicon from EMR using silicate bacteria is investigated, with flask experiments conducted to optimize the parameters in the bioleaching system. For metal ions, the concentrations of manganese (Mn), Co, Ni and Pb in solution were measured to determine the environmental safety effects before and after bioleaching. The results show that the bioleaching rates of available silicon in the slag were mainly affected by the temperature, pH and pulp density. Under the optimal conditions of temperature of 30 °C, pH of 7.0, pulp density of 5 percent, shake flask rotational speed of approximately 210 rpm, particle size of approximately 0.150 mm and leaching time of 16 d, the concentrations of available silicon in the bioleaching system rose to approximately 110 to 140 mg/L. The metals remaining in the residues were mainly bonded in stable fractions, with concentrations lower in the leachate after bioleaching. This study demonstrates that silicate bacteria can be used to increase the contents of available silicon from EMR, and that bioleaching technology can realize the harmless resource utilization of EMR.

By Bryan A. Bartley

About 1,000 machines around the world are breaking rock and hard abrasive materials by a very economic, high intensity, autogenous process, but this method is largely ignored by the mining industry. This vertical shaft autogenous impact crusher has impact velocities around 70 m/s, which compare with those of Cascade and SAG mills of up to 10 m/s. The autogenous impact, breakage processes are all at higher intensity levels and the products reflect this difference. The topic of liberation is breifly considered. A series of tests with a laboratory scale machine are reported to illustrate a number of the characteristics of the process. This paper highlights topics for further evaluation and research.

Jan 1, 1992

By C. J. Pritchard, A. B. Cecala

An evaluation was performed on a district recirculation system at a trona mine in Granger, WY. A 1.52 m-diam (5 ft-diam), 37.3-kW (50-hp) vane axial fan was installed in a crosscut between the intake and return airways and recirculated about 31.4 m3/s (66,578 cfm) of air back into the intake. This amounted to a recirculation factor of about 20% of the return air. This air was part of the primary ventilation to three different continuous miner sections at operating distances of between 610 m (2000 ft) and 1829,m (6000 ft) from the recirculation fan. The mine environment was constantly monitored for respirable dust, methane and carbon monoxide in the operating sections and in the main intake and return entries. In addition, air samples were taken with and without the recirculation system during the evaluation and analyzed using gas chromatography. The results of this study showed only small increases in dust, while all other mine contaminants remained at such low levels that it was impossible to determine any relative changes from the recirculation system. Because of this, a brief SF6 tracer gas analysis study was subsequently performed to more precisely determine an increase in a mine contaminant with the recirculation system.

Jan 1, 1992

By William A. Kneller

Fifteen samples of chert from seven localities in Ohio were tested for potential durability and reactivity in concrete. The tests determined are porosity, pore-size distribution, relative degree crystallinity, specific surface area, and degree of dissolution according to the ASTM C289-71, Potential Reactivity of Aggregates, Chemical Methods. The results of these tests were compared with petrographic, electron optical, physical-chemical, and engineering properties of the chert samples. Based on these tests, the important properties that affect the durability and reactivity of chert in concrete were observed to be: (1) porosity, (2) pore-size distribution or pore spectra, (3) relative degree of crystallinity, (4) grain size, (5) specific surface area, (6) impurities, and (7) amount and species of quartz present-all of which are functions of original composition, time (geologic age), depth of burial, tectonics, and diagenesis. Preliminary results of this study indicated that the geologic history and physical-chemical properties of chert vary from one sample to another, and any one or combination of these parameters affect the performance of the chert in concrete. These complex interrelationships are difficult to ascertain; if the performance of the chert in concrete is to be predicted, it is necessary to study in detail this enigmatic material.

Jan 1, 1978

By M. Quamrul Ahsan, Andrew Griffiths, Edward P. Jucevic

Heap leaching of precious metal ores using the cyanide process is extensively used in the Western U.S.A. for extracting gold. Consequently, the impact of cyanide in the spent heap is closely examined by environmental agencies and permitting authorities. Currently, many states require that all decomnissioned heaps be detoxified before abandonment. This paper describes a case study for detoxification of spent heaps at the ACH-Dayton Project using hydrogen peroxide. The chemistry of cyanide detoxification by hydrogen peroxide, together with simplicity of a detoxification operation, is discussed.

Jan 1, 1989

By Young C. Kim

Use of geostatistics to solve mining problems is gaining importance as the cost of developing new mines is increasing and there is a need to mine more marginal deposits. But, until recently, coal companies have shown little or no interest in geostatistics. However, the stringent quality controls on coal burning has led to a surge in interest in improved methods for estimating clean coal characteristics. Until now, most of the geostatistical applications have centered on the problems of estimating in-situ coal characteristics (Sabourin, 1975; Wood, 1976, 1979; Fang and Stark, 1976; Pauncz and Nixon, 1979; and Knudsen et al., 1980). Little work has been done in applying geostatistics to coal washability, except that by Armstrong (1980). Applying geostatistics to coal washability basically means the estimation of cleaned coal characteristics, with the aid of geostatistics. Cleaned coal estimation plays a very important role in overall emission control strategy, as can be seen by the general flow diagram of such a strategy shown in Figure 1. The scope of this paper is limited to one aspect of the overall emission control strategy shown in Figure 1; namely, the prediction of cleaned coal characteristics using geostatistics.

Jan 1, 1982

By C. P. Mangelsdorf, Richard A. Allwes

At the request of the U.S. Department of Labor, Mine Safety and Health Administration (MSHA), the U.S. Bureau of Mines evaluated the suitability of using tri-sets for protecting mine personnel in roof-fall prone areas. A steel-set arch provided by MSHA served as a basis for evaluating the performance of the tri- set. All tests and analyses were conducted according to the arch canopy test and design procedures developed by the Bureau. Theoretical resistance functions were established for the steel-set arch and tri-set and were representative of their experimental behavior. The resistance functions were used to determine the energy absorption capacity of the structures and to predict their dynamic response to impact loading. The dynamic tests demonstrated that the arch canopy design procedure is appropriate for tri -sets and yields conservative designs for both steel-set arches and tri-sets. As a result of this work, it is recommended that tri-sets may be considered for protection against roof falls, provided that the arch canopy design procedure is utilized for each application and that the principles underlying the design procedure are understood.

Jan 1, 1992

By Joseph Peterson, Alexander May

The Bureau of Mines used geochemical modelling computer programs to characterize a site containing lead slag generated by a lead processing facility. Tests for toxic elements by the U. S. Environmental Protection Agency (EPA) extraction procedure showed that all elements except lead were in compliance. Concentrations for lead ranged from 28 to 30 ppm. However, analysis of water samples from monitoring wells resulted in no lead concentrations that exceeded the National Drinking Water Standard. A discussion of a computational program to calculate concentrations of lead species and several other ions is presented.

Jan 1, 1991

By Guangyao Si, Ismet Canbulat, Xun Luo, Yi Duan

Routine analyses of seismicity and event locations are essential for coal burst risk management, especially in the presence of unfavorable and complex geology. In an Australian longwall coal mine, a small-scale seismic monitoring network was installed to monitor a section of a major dyke intersected by the roadway, which was classified as a coal burst prone zone. The Deep Convolutional Neural Network (DCNN) technique was adopted for automatically discriminating seismic events to assess seismicity in this zone. The discriminated seismic events were located with the Shortest Path Method based on the Boundary Discretization Scheme (BDS-SPM) for temporal-spatial seismic event distribution analysis. The results demonstrate that the seismic events are discriminated with an average accuracy of 94%. Moreover, the seismic events are more accurately located using the BDS-SPM with a 3D heterogeneous velocity model compared with results obtained with a homogeneous velocity model. The temporal and spatial variances in seismic activities identify that the rock fractures in the dyke zone are closely related to the longwall mining process and a local dyke has a controlling influence on the stress concentration in its vicinity.

Apr 26, 2022

By C. Sun

The Leeville underground mine has been in operation since 2006 and currently produces 3,300 tons of ore per day with an average gold grade of 0.4 opt. The mine has a large horizontal extent of 2,500 feet by 500 feet and a vertical extent of 20 to 200 feet. Based on the characteristics of the ore bodies, the deposits are divided into several mining zones. The geotechnical properties of mining zones are also different from one zone to another. A successful geotechnical collection system is very important for the mining designs and operations in the Leeville underground mine.

Jan 1, 2010

By T. Kelly

The post-apartheid South African government has instituted a new minerals policy. As part of the new policy, minerals rights are now held by the national government, not as private property. In addition, the national government desires to see a greater participation of all South Africans in the corporate mining arena. At the same time, the national government has adopted a policy of a strong monetary unit compared to the U.S. Dollar. The combination of these tow policies has led to changes within the platinum mining industry.

Jan 1, 2004

By Frank C. Appleyard

As the environmental movement gained force during the past few years, it was inevitable that attention would be focused on surface mining, and we have seen this method of extracting minerals from the ground come under heavy attack by conservation groups, the press and television, legislators at all levels of government,, and the public at large. It is difficult, and in some situations, perhaps impossible, to measure either the need for, or the results of, land reclamation in absolute terms. Therefore, much of the criticism of surface mining has been based upon subjective analysis rather than hard data, with the result that discussion of the subject often includes a fair amount of emotional response. To be fair, this reaction is not limited to just our critics; even we hard headed engineers sometimes respond in the same way, an observation with which you may agree when I finish this talk. This leads to the thought that whether you are for it, or against it, land reclamation in many respects is a state of mind. That is, our reaction to it can vary considerably, depending on how far we have thought it through. And think it through we must, because the pressures being brought to bear need to be met with positive actions if the problem is to be brought under control, and in the next few minutes I would like to discuss from a management point of view some ideas which might aid in this thinking process. It would be a mistake, I believe, to think that the current energy crisis will suddenly bring the environmental movement to a stop, and therefore, we can relax and go back to running our busi¬ness the way we used to. This is not realistic; on the contrary the energy crisis is focusing attention on the limitations of our natural resources as nothing else could, and with respect to land

Jan 1, 1974

By K. G. Colman

Introduction This text is intended to provide the operator and turnkey contractor with the basic data for sizing vibrating screens to be used in ore crushing plants. The basic capacities, modifying factors, etc.. used in the area requirement calculations were developed empirically and modified to their present values based upon years of practical applications. It must be pointed out that screening is much more of an art than an exact science; however. the information presented here should provide for reasonably accurate screen sizing when applied to many metallic ores. Types of Screens There are two types of screens which can be used for strictly sizing applications. These are two- and four-bearing screens; both are inclined circle-throw machines. Two-Bearing Screens The motion of a two-bearing screen is generated by unbalanced weights attached to the vibrator shaft. The body of the machine is usually supported by steel coil springs (see Fig. 8). The main advantage

Jan 1, 1985

By William H. Pomroy

This report describes research leading to the design, prototype fabrication, and successful in-mine proof-of-concept testing of two improved stench fire warning systems for underground noncoal mines. The stench system, widely used in underground noncoal mines to warn of fire or other emergency suffers several serious shortcomings, including the toxicity of the odorant leading to debility in miners; reactivity of the odorant with iron oxide, resulting in unreliable warning because the odor may fade when transported long distances in steel pipe; lack of control over the rate at which agent is released into the air-stream, resulting in some work areas receiving unbearably high stench concentrations and other areas being missed altogether; lack of visual indication of system status, valve positions, or proper system operation; and excessively long stench transit times. In 1979, the Bureau of Mines, U.S. Department of the Interior, began research to upgrade the stench warning system. Two systems were subsequently developed which offer significant advantages over current systems.

Jan 1, 1984

By S. Horton, F. L. Stanley, P. J. Bethell

Introduction The McClure River Processing Plant is located at McClure in Dickenson County, VA. The plant was originally constructed in 1979 as a 600 st per hour facility. The plant is fed by coals from numerous mines in the area as well as a major longwall mine onsite. Coal is processed predominantly for the metallurgical coal market. The original plant was comprised of three separate processing circuits incorporating a heavy medium vessel for the coarse material (+10 mm). Intermediate sized material (10 x 0.6 mm) was beneficiated in heavy medium cyclones, with the remaining fines (0.6 mm x 0) passing to froth flotation for upgrading. The products from all three circuits were combined prior to thermal drying and then stored in silos or ground storage prior to shipment to the metallurgical coal markets. A middlings heavy medium cyclone circuit was also present to rewash the vessel and primary heavy medium cyclone rejects. The original circuit is as shown as Fig. 1 (Editor's note: All figures are reproduced at the end of this paper.) In reasonably close proximity to the McClure Plant is the much older, less efficient Moss 1 Plant, (Chance cone, table, water only cyclone, froth flotation, Fig. 2), which prior to the McClure Plant expansion was processing considerable tonnages of coal. At that time, the McClure River Plant was processing coal at the maximum possible feed rate, and the Moss 1 Plant was finding increasing difficulty in maintaining the stringent quality specifications on its major metallurgical coal accounts. Given the fact that many of the feeder coals to Moss 1 could be moved with minimal difficulty and cost to McClure, an exercise was conducted to evaluate the potential of expanding the McClure Plant. This would result in transferring coals from Moss 1, thereby increasing yield, reducing operating costs, and enabling customer specifications to be met more easily. After evaluating many possible ways of expanding the McClure Plant, we eventually settled on an approach based on the idea of Gallagher at German Creek in Australia (Gallagher, 1986). Our objective was to increase plant capacity by removing the coarser size fractions (0.60 x 0.15 mm) from froth flotation and at the same time eliminating the finer fractions (1.25 x 0.6 mm) from the heavy medium cyclone circuit, thereby allowing these circuits and therefore the plant as a whole to increase its capacity. These size fractions (0.60 x 0.15 mm from froth flotation and 1.25 x 0.6 mm from the heavy medium cyclone circuit) would be treated in a new spiral circuit. After desired evaluation of the various circuit capacities, including desliming screen, clean coal filter and thermal dryer capacities, etc., it was concluded that we should be able to maintain high levels of processing efficiency in the existing circuitry while at the same time expanding plant feed rate from a nominal 600 st per hour to 1000 st per hour, thereby achieving the objectives The circuit that was finally settled on is shown in Fig. 2. Several unique features were incorporated in this circuit in an attempt to maximize processing efficiency and reduce maintenance costs. First, the idea of a single-stage spiral circuit was abandoned in favor of a two-stage circuit incorporating rewashing the primary spiral middlings in a secondary spiral (Bethell, 88). The spirals selected were Mineral Deposits Model LD4 units. It was felt, after much previous testing, that spiral middlings rather than being a true middling gravity fraction were in fact a combination of true middlings with a preponderance of misplaced light coal and high-density rock. Consequently the insertion of this material directly into either clean coal or refuse streams (per normal practice) would only lead to loss of efficiency. The operating philosophy behind the design of the circuit was to produce the purest coal and rejects possible by adjusting the spiral splitters. Misplacement of refuse into the clean coal and vice versa would be minimized by taking a fairly large middlings cut. By reprocessing this material (10%-15% of primary spiral feed) in a secondary bank of spirals the misplaced material in the primary middlings would be reprocessed and its probability of reporting to the correct stream greatly enhanced. To minimize fines loading on the spirals, fine aperture sieve bends were to be included. A further novel feature of the circuitry is the desliming/ dewatering system. A philosophy of accepting inefficiency but forcing it to work in our favor was developed. The dewatering screens (Linatex Combis) were chosen not for their ultimate screening efficiency but for their ability to remove slimes (tolerating a fair quantity of oversize in the effluent) and their enhanced maintenance characteristics. Any oversize passing into the effluent, together with the fine coal centrifuge effluent, would pass to classifying cyclones, the objective of which was to reject to overflow (and hence froth flotation) as many fines as possible (-150 µm) without running the risk of losing coarse (1.25 x 0.15 mm) material to oversize. Hence, by a process of producing a "slime free" screen product coupled with a "coarse free" cyclone overflow, sizing efficiency could be maximized. Obviously, recirculating load had to be factored into the Combi Screen design capacity. The spiral circuit as shown in Fig. 2 was installed at McClure River in January 1988. The spiral circuit efficiency was very high immediately, and, after the normal debugging, plant capacity has been increased to the point at which we are currently processing of the order of 1100 st per hour. Test program The performance of the spiral circuit has been evaluated by two major samplings of the entire new circuit, coupled with routine bi-monthly tests on all other major components of the plant circuitry.

Jan 1, 1992

By David G. Chedgy

The Meadow River No. 1 Preparation Plant, owned by Sewell Coal Company, a subsidiary of the Pittston Company, was commissioned in the spring of 1974. The plant is designed to process 400 TPH of 5" x 0 raw coal. The 5" x 114'l fraction is processed in a Heavy Medium Vessel with the 114 x 28M reporting to Deister Tables for cleaning. The 28M x 0 fraction is cleaned in flotation cells, with the froth going to clean coal vacuum filters and the tailings to a static thickener where the underflow is reclaimed on Refuse Filters prior to disposal. The noise dosage a worker receives is determined by the ratio of the length of time the worker spends in a particular noise environment divided by the noise exposure in that particular environment. If the worker is exposed to several different sound levels, his total dosage would be the sum of each of the individual dosages. The equation for determining the dosage is: [ ]

Jan 1, 1976

By Tim O’Neil

Big and getting bigger. Barrick Gold Corp., the third-largest gold producer in the world, began production in September — ahead of schedule — at its Meikle Mine. At a scheduled full production rate of 12.4 t/a (400,000oz/year), it will be the largest producing underground gold mine in the United States. The $180-million Meikle Mine is located on Barrick’s Goldstrike property in Nevada and has 205 t(6.6 million oz) of gold reserves. The compact Meikle deposit has an average ore grade of 23 g/t (0.68 oz/st), making it one of the highest-grade mines in the country.

Jan 1, 1996

By Oscar H. Lentz

During 1960, the controversy over percentage depletion reached the level of debate between presidential candidates. Nixon took the position that he would not tamper with the status quo in this matter. Kennedy took the position that he was willing to take a fresh look at the issues involved. Kennedy's position appears to have been based upon two premises: (1) new sources of federal revenue may be needed; and (2) current depletion rates, even if sound in principle, may be too high and, therefore, inequitable. The latter premise constitutes the basis for the claims that depletion allowances are simply "loopholes" of tax avoidance. Very probably the controversy over percentage depletion will remain in the political limelight during most of the coming decade. It is quite possible that the current depletion rates, at least those for oil and gas, will be reduced during this period. The aim of this paper is to isolate the complex causes of this mounting opposition to percentage depletion.

Jan 1, 1961

By Matthew Burdick, Andrew Rule, Erica Bailey

The Second Narrows Water Supply Tunnel, Burrard Inlet Crossing project for the Greater Vancouver Water District entails deep shaft construction, subway sized pressurized face tunneling through highly variable ground conditions, installation of three permanent steel water mains and construction of elaborate valve chambers adjacent to either shaft. The paper discusses key elements of the planning and implementation of 6.69 m Ø slurry mixshield tunnel boring machine (TBM) assembly in a small diameter deep shaft including incorporation of a fully pressurized launch lock, preparations for saturation diving, surface support infrastructure and initial mining sequence.

Jun 13, 2021