Search Documents

By L. V. Wade

The use of longwall/shortwall mining systems is under increasing scrutiny by the U. S, coal industry as a means to reverse the decline in productivity. The success of these mining systems depends to a great extent upon designing the system hardware to best suit local conditions. Of particular importance in this regard is designing the various elements of the total ground support system, including face, face end, and gate road supports, to accommodate local geologic conditions. This presentation centers on the problem of selecting the face support system. The existing geologic situation can influence the selection of the face support hardware in a variety' of ways. In general terms, these influences can be grouped into the following four areas: 1. The capacities required of the support unit; 2. The roof, coverage supplied by the support units; 3. The flexibility required of the support unit to meet changing geologic conditions; and 4. The required stiffness characteristics of the individual support units both vertically and horizontally. The following will center on the first area, i.e., the required d capacities of the support unit, in particular, the maximum required load density for a particular geologic situation.

Jan 1, 1976

By G. Rinelli, Arthur F. Colombo, Donald W. Frommer

With the opening of the Tilden mine near Ishpeming, MI, a new era in iron ore beneficiation was begun. A description of a U. S. Bureau of Mines investigation is summarized to illustrate the selective flocculation-deslime-flotation process developed by the Bureau and used at the Tilden concentrator, which is also briefly described. The operating parameters for the selective flocculation-cationic flotation of an oxidized taconite from the Mesabi range are discussed. A water reclamation system using lime and a cationic flocculant was applied to reclaim the effluents from a 900-pound-per-hour flotation pilot plant. About 80 percent of water requirements were recovered, and the calcium content of the reclaimed water was found to be more important than clarity in influencing the selective flocculation and flotation processes. Although reclaimed waters with about 10 ppm calcium registered turbidities of approximately 5,000 ppm SiO2 equivalents, the concentrates produced using these waters contained 64 percent Fe and =5.0 percent SiO2 and had accompanying iron recoveries of 75 percent. Lower grade concentrates resulted from using reclaimed water with higher calcium contents and lower turbidities.

Jan 1, 1976

By D. F. Strong

Most Newfoundland. mineral deposits can be clearly classified as within rocks formed either as accreting plate margins (ophiolitic pyrite-chalcopyrite massive sulfides such as Betts Cove, Whalesback, York Harbour, chromite at Lewis Hills, and asbestos at Baie Verte), at consuming plate margins (Kuroko-type polymetallic massive sulfides such as Buchans and Pilleys Island, porphyry-type Mo-Cu at Rencontre, fluorite at St. Lawrence), or within plates (zinc deposits at Daniels Harbour, sedimentary iron ores at Wabana, manganese in Conception Bay.) As these metallogenic patterns can be convincingly extrapolated southward into the Appalachians and northward to the Caledonides, they provide an important means of eliminating and selecting areas for particular exploration targets. Sonic criteria are described for the recognition of these environments of differing economic potential.

Jan 1, 1973

By W. A. Haley

Wheel loaders became important bulk materials handling tools in the early fifties. As they grew in stature, productivity, reliability, and acceptance, the demand for larger, more rugged machines evolved. In the early sixties, the introduction of a 6-yard model by a major equipment manufacturer led quickly to widespread experimenting and rapid worldwide acceptance in loading blasted rock in stone quarries and smaller metal mines. As the wheel loaders grew in popularity for shot rock loading, larger models, 12- to 15-yard size were developed and saw widespread use by 1970. In the past 20 years, at most quarries and small to medium size mines, most cable operated power shovels have been replaced by large wheel loaders and more recently, hydraulic excavators as the primary loading tool. Wheel loaders larger than the 15-yard class are not used widely. Until about 1970, very few overburden haulage trucks were used in domestic coal mines. About that time, many states started enforcing stringent mine relcamation regulations and in 1977, even more stringent federal legislation was passed. These controls brought about drastic changes in coal surface mining methods in the mountainous areas of Appalachia, in smaller midwestern mines and in the large mines of the western states. Basically, simple material casting methods were replaced at most eastern mines by "haul-back" and "mountain top mining" methods using controlled placement of overburden as it is removed from the coal. These methods dictated much more extensive use of loaders/ shovels and trucks to the point that most coal mining in those areas is now by loader/shovel trucks methods. And those areas have become the home of the country's largest population of large wheel loaders and trucks in the 35- to 85-ton size class with a trend to even larger trucks and shovels. To maintain equal production or provide for growth, the new methods have caused a sharp increase in machine intensity to the extent that at some mines, up to three times as many machines were required to mine a million tons of coal in the late seventies as compared to the machine needs in the sixties. Mining costs and coal prices also took a big jump in the mid-seventies, paralleling the drastic price increases in oil and other forms of energy.

Jan 1, 1984

By S. C. Nordeng

The program described in this paper is primarily a test of the possible utility of multiple regression in ore search, It was carried out as a cooperative project between White Pine Copper Company, the Institute of Mineral Research and the Department of Geological Engineering of the Michigan College of Mining and Technology. The authors wish to thank Dr. Cleaves Byers, Associate Professor of Mathematics, MCM&T, and Mr. Robert DeBaubien, Graduate Student in Mathematics, MCM&T, for their work in programming the project for the computer,

Jan 1, 1964

By J. P. McKinney

A mathematical model is presented for the electrokinetic dewatering of suspensions of phosphatic clays. The modeling approach couples a boundary-element model for solution of Laplace?s equation to a recently developed constitutive equation that relates the change in solids content with applied electric field and time. The observation that the electric field controls both the maximum solids content achievable and the time required to reach that value is shown to severely constrain the application of electrokinetic dewatering strategies to an entire clay settling area. The approach, however, may be feasible for implementation as part of a continuous plant process.

Jan 1, 2011

By R. Vogt, H. C. Mult, F. L. Wilke

INTRODUCTION At present, the capability of production planning software based on Linear Programming (LP) is still limited to the optimization of the single LP-run. This is due to the LP-model itself which cannot consider the interdependencies between individual LP- runs. With regard to planning of selective mining this limited way of optimization frequently leads to situations, where the remaining and accessible ore blocks do no longer allow to produce ROM-ore in the qualitative composition required by the ore processing plant. However, many of the aspects taken into consideration when setting up production plans built from mutually dependent LP-runs cannot be modelled in a system of linear equations. They are thus unsuited for treatment with LP and have to be taken care of by the planning engineer without any assistance by the system. The KBS currently under development is intended to assist the planning engineer in designing a production plan under special consideration of the combination of consecutive LP-runs and blending beds. It is not necessarily intended to find the optimum solution within a given planning situation which is, anyway, hard to determine due to the multitude of influences. The objective is rather to work out a good and - from the practical point of view - feasible production plan. The new aspect with respect to mine planning is the integration of expert knowledge and experiences via the KBS into the planning process in order to support the planning engineer. The planning system is being developed in close cooperation with an iron-ore open pit mine. COMPONENTS OF THE PLANNING SYSTEM The software is being developed on a workstation under UNIX and comprises the components LP, CAD-module and the KBS. The applied multi-goal LP-algorithm is an in-house development of the Department of Mining Engineering at Technical University Berlin. It was already successfully implemented within other mine planning programmes and was only slightly adapted to the specific needs of the present system. Within individual LP- runs it finds the optimum qualitative composition of ore production in the sense of the selected optimizing criterion and under the given restrictions: i.e. it determines tonnages to be mined from blocks in order to optimally meet the requirements of the ore pro- cessing plant. A CAD-module based on the commercial SURPAC package in combination with a simulation device is used to graphically depict the block model and progress of mining. Both LP-algorithm and CAD-package are integrated in the KBS. It has been decided to use the shell NEXPERT OBJECT as it is a hybrid system which supports both rule-based and object-oriented knowledge representation. MINE-MODEL AND LP-MODEL KBS have to be tailor-made for specific planning problems. Therefore, it had to be decided which specifications of the iron-ore mine should be represented in the model. As the limited possibilities of a university institute do not allow to develop a KBS for mine planning which is ready to use in industry, it was decided to concentrate on those characteristics that can be regarded as typical for iron-ore surface mines and that seemed to be suited for treatment with knowledge-based techniques. The following chapter summarizes the most important features of the mine model. The description of the requirements to the mine's sales products is followed by an outline of the applied LP-model. Mine model • The model of the mine as it is used for planning consists of • the block model of the deposit, • the mobile equipment, • stockpiles and blending bed and • the requirements to the sales products. The deposit is described by a block model which contains data on the chemical composition, LOI, grain size and tonnages. Grain size was included as it is important for the two sales products of the mine. Furthermore, it is known whichs blocks require and which don't require blasting; this is relevant to the assignment of loading equipment to individual blocks. The blocks are devided in three categories: • ore, which will directly be taken to the blending bed; • waste, which will be put on the waste dump; and • blocks which will be either transported to the blending bed, to stockpiles or to the waste dump depending on the specific planning situation. This decision is made during planning. Neighboring blocks are combined in mining areas to which the loading equipment is individually assigned. Mobile equipment comprises shovels and wheel-loaders as well as trucks. The characteristics of the loading equipment are important for their ability to load different blocks and for the permissible degree of their re-positioning etc. The mine disposes of a blending bed for homogenization of the production, of a waste dump, and of several stockpiles with different ore qualities. The requirement to make only limited use of the stockpiles for economic reasons is included in the KBS. According to long term planning two commercial products have to be produced, which differ both in grain size and qualitative composition (TABLE 1). Their mass-proportions in the blending bed have to be within a fixed range. Not considered in long term planning is the occasional need for lump ore, which occurs at very short notice and has to be produced in a "campaign-like" manner. This requires the total re-arrangement of all plans for on- coming blending beds and would therefore be ideally suited for

Jan 1, 1996

By A. R. Bell

Rio Algom Limited are currently undergoing a major expansion of their mining operations in the Elliot Lake area. To date this has involved the increase of output at the Quirke Mine from 4080 to 6350 tonnes per mill day (4500 to 7000 tons), the rehabilitation of the Panel Mine to produce at the rate of 2990 tonnes per mill day (3300 tons) by 1980, and the rehabilitation of the Stanleigh Mine to produce 4540 tonnes per mill day (5000 tons) by 1984. In addition, the planning for the rehabilitation of the Milliken Mine to produce 4990 tonnes per mill day (5500 tons) is now underway. This major expansion is taking place at a time of increasing awareness of occupational health matters and has involved very high capital expenditures and detailed planning related to the ventilation system to endeavour the provision of an acceptable environment. The paper discusses the ventilation systems, established and proposed, and relates them to historical and current data on mine air contaminants.

Jan 1, 1980

By Robert Essler, Paul Marsden, Paul Pandrea

"1. THE VICTORIA STATION TRANSPORT HUB Victoria Underground station is part of the Victoria transport hub, which comprises one of London’s main train termini and a major bus station. At the Underground station, the District Line running in the older shallow brick tunnels dating back to 1868 cross the Victoria Line running in the lower tunnels, which were opened in 1969. After Waterloo, Oxford Circus and King’s Cross/St. Pancras Tube stations, Victoria is the most frequented station on the London Underground network and is used by over 80 million passengers per year. Capacity at Victoria Tube station has been inadequate for many years with passenger numbers steadily rising. Overcrowding is a constant challenge and the station has to be closed regularly during morning and evening peaks until sufficient trains pass through to clear the platforms. For this reason an extension has been debated since the 1990s. After intensive preliminary investigations and feasibility studies covering many variants, which included a large-scale jet grouting test to determine the applicability of this technology as a protective measure for the tunnelling works, the project was officially started with the Victoria Station Transport and Works Act Order (Secretary of State, 2009) effective on the 18th of September 2009. Following a competitive tender process a joint venture of Taylor Woodrow and BAM Nuttall were awarded the contract by London Underground, with their design being carried out by Mott MacDonald Ltd. Ensuring the busy station remained open to the public was a key requirement of the Victoria Station Upgrade. Jet grouting works, which were executed from ground surface, were also carried out while the station was fully operational 2. OVERVIEW The Victoria Station Upgrade aims to increase the capacity of the Underground station significantly and one of its major design objectives is to optimise the transfer between the Underground lines. In order to achieve this, the following new structures are currently under construction: •,A new North Ticket Hall •,Extension of the existing South Ticket Hall •,Nine new escalators •,Connecting tunnels between the North and the South Ticket Hall •,8 new lifts providing step free access to all platforms •,An improved connection between the rail/bus terminus and the Underground station As the elevation and geometry of the existing structures cannot be changed, the new structures need to be adapted to the existing structures (see Figure 1)."

Jan 1, 2016

By X. X. Shao

Dewatering of ultra-fine clean coal slurry to a low moisture level of20 percent is difficult using the conventional techniques. A novel approach, which utilized mixing of fibrous waste material, such as paper, carpet and wood, with coal slurry prior to dewatering was developed. It was found that addition of about 10 Kg/t of carpet fibers or 5 Kg/t of raw paper pulp lowered the filter cake moisture from 22.5 to 18 percent. The compressive strength of the filter cake improved from 0 to 4.5 Kglcm2 and impact resistance from 0 to 4. The experimental data indicated that the handling character of the dewatered fine coal was improved significantly.

Jan 1, 1998

By G. A. Christie

This paper presents a vision system capable of providing an accurate estimate for the volume of stockpiles using 2D images. By imaging a stockpile from multiple viewpoints with a two-camera system, a 3D point cloud of known scale is generated using image-based 3D reconstructions. With a small amount of user interaction, the points that correspond to the surface of the stockpile are extracted and used to measure the volume. The hardware required for the two-camera system is light enough to be carried by a small unmanned aircraft and is a cheaper alternative to LiDAR while still being competitive in terms of accuracy. When testing the volume measurement algorithm on a stockpile of known volume, the measured output was found to have less than a 3% error from the ground truth.

By D. W. Hutchinson

One of the most important problems facing the coal industry today is the disposal of refuse from the coal preparation plants in a safe, economical, and efficient manner while complying with all legal requirements. The most commonly used refuse disposal method has been landfill/impoundment. In this method, the coarser refuse fractions are disposed of by layering and compaction into a landfill. The fine coal slurry refuse fraction is impounded in a dam constructed of a portion or all of the coarser refuse fractions. The failure of an impoundment at Buffalo Creek, Saunders, West Virginia and the sliding failure of a coarse refuse pile at Aberfan, Wales, England, resulted in an evaluation of refuse disposal methods by various regulatory agencies as well as coal producers. The result of this evaluation was the promulgation of Federal regulations dealing with the preparation, operation, and final abandonment of coal refuse disposal areas. As a consequence of these regulations the use of the landfill/impoundment method of disposal became in some cases economically unfeasible or technically impossible. At the time of the promulgation of the new Federal regulations, United States Steel Corporation was in the process of designing the Cumberland preparation plant. As a result of the new regulations

Jan 1, 1977

By I. Iwasaki

Precious metals are commonly believed to be recovered along with sulfide minerals in flotation, but a few neutron activation analyses showed that the recoveries of gold and silver were unexpectedly low. Recoveries of platinum group metals remained unresolved due to interferences in the analyses. Electron micro-probe, scanning electron microscope and scanning auger microprobe analyses have identified nickel arsenide minerals in the ore and confirmed a close association of platinum group metals with the arsenide minerals as minute inclusions. These results indicated a need for re-evaluation of flotation procedures which have so far ignored special problems related to arsenide minerals. The electrochemical and flotation behaviors of nickel arsenide and their implications to the flotation recovery of arsenide minerals from copper-nickel bearing Duluth gabbro are presented.

Jan 1, 1985

By George W. Parker

The ever increasing costs of labor and supplies have made it imperative that operators of open pits look for some way in which to cope with these increases. One of the most logical ways to increase the efficiency of an operation is by the introduction of larger haulage equipment, as generally haulage costs are the greater portion of the over all expenses. These larger haulage units require larger shovel units. In the late 1930's and the early 1940's large mining, quarrying and heavy construction operations had more or less standardized on the 4 to 6 cubic yard shovels. During this same period the haulage units were generally 22 to 27 tons. Some ten years ago 9 - 13 cubic yard shovels along with plus 50 ton haulage units were introduced by manufacturers in an effort to enable operators to decrease costs.

Jan 1, 1962

By R. E. Hucko

The principal thrust of the U.S. Department of Energy (DOE) Coal Preparation R&D Program is to develop technology to reduce the ash and sulfur contents of United States coals to levels such that the resultant product can be formulated into a high quality solid or slurry fuel that could replace oil or natural gas in both new and retrofit applications. Specifically, the objective is to develop and refine cost-effective physical and chemical beneficiation processes to extract 85-95 percent of the total sulfur and ash. The Coal Preparation program is implemented by the Pittsburgh Energy Technology Center (PETC) and is conducted both in-house and by a cross section of industrial organizations, universities, and national laboratories. Research is subdivided into three areas -coal characterization, beneficiation, and ancillary unit operations. This paper will provide a brief overview of many of the research projects being carried out in these areas in fiscal year 1984.

Jan 1, 1984

By Joseph Padgett

Of all the fossil fuels produced in the U. S., coal is by far the most abundant. U. S. reserves amount to an estimated 1.5 trillion tons, 2,500 times the 600 million tons produced in 1970. Although it would not be possible to recover all of this coal economically with current mining technology, a significant portion would be available given the proper circumstances. With existing technology, approximately one-eighth of these reserves is accessible, an amount which would last for several hundred years at the 1970 level of production. On the face of it, this substantial reserve should go a long way in meeting the Nation's energy needs. But coal offers special problems. As additional coal is mined and then burned, there are increased costs to the Nation's land, water, skies, and health. Hence, coal poses a dilemma because of its dual status as one of our most abundant domestic fuels and as one of our major sources of environmental degradation. Against the benefits that would be chalked up in the areas of national security, balance of trade, and economic well-being from the increased use of coal, we must enter on the debit side of the ledger the increased environmental cost. This paper reviews the use of U.S. fossil fuel, the drawbacks of coal as an energy source, the means being developed to overcome these drawbacks, and the background behind the present sulfur emission regulations relative to coal combustion. It also discusses in detail the Federal Environmental Protection Agency's (EPA's) current policies to ensure the continued use of coal as a major source of energy for fossil-fuel fired power plants.

Jan 1, 1973

By J. A. Meech

An analysis of screen design options on the operating efficiency of secondary crushing plants has been conducted using a dynamic computer model. The model allows for the simulation of a wide variety of crushing circuits and can be run on either a microcomputer (IBM PC/XT) or a large time-sharing mainframe computer. Size reduction and separation characteristics of crushers and screens are based on standard manufacturer design and performance data. Input/output routines are available in tabular, alarm or strip chart recorder modes to facilitate operation of the program. A number of alternate circuit designs are compared to show the influence of surge capacity, screen size and area, screen deck location, and closed side crusher settings on the operation of a 10,000 ton per day plant. The program is currently in use at Queen's University to teach plant operations and control. It has potential to be a valuable tool for operator training.

Jan 1, 1985

By M. S. Tsai

Recovery of uranium from wet-process phosphoric acid is a newly developed source of uranium. Many processes have been developed but the OPAP (octylphenyl acid phosphate) process is still the valuable one because the OPAP reagent compound has the high extraction ,power and cheap cost. The OPAP process was already studied by murthy(1) in 1970 and its complete process flow sheet was first fulfilled by F.T. Hurst(2) in 1974. WCFC(3) (western Co-op Fertilizer Ltd.) in cooperation with ESI (Earth Science Inc.) set up the OPAP uranium recovery pilot plant in Canada in 1978. We have studied the OPAP process since 1974 and first improved the OPAP extractant by proper adjustment of the DOPAP/MOPAP mole ratio with CH3OH-H20 method, resulting in shortening the phase separation time and avoiding the precipitation occurrence in our process. Second, we utilize the reduction and oxidation occurring by DC power supply on either side of the membrane to achieve the extraction and stripping at the same time. An improved OPAP process in which high recovery yield of uranium and acid uncontaminated by iron has been developed in our laboratory.

Jan 1, 1982

By L. Zhou, L. Yuan, D. Bahrami, Y. Xue

Underground mine accidents, such as mine fires, remain a health and safety risk to mine workers. Researchers at the National Institute for Occupational Safety and Health (NIOSH) are developing a data-driven, predictive model for characterizing the location and size of unknown underground fires. This study examines applying a machine learning-based model to predict fire size and location in a large underground metal mine based on hypothetical scenarios on the model performance. The results show that the size and location of an unknown fire can be determined with over 80% and 90% accuracy, respectively, and potentially help to reduce the risk of hazardous conditions for emergency response.

Feb 1, 2024

By Howard Brown

High purity, high brightness limestone deposits in the San Bernardino Mountains and Mojave Desert region occur in upper Paleozoic carbonate rocks which are part of an upper Precambrian and Paleozoic sequence that unconformably overlies crystalline basement. The Paleozoic strata are divided into formations and members, and correlated with strata of the inner Cordilleran miogeocline. The region has been affected by multiple Mesozoic intrusive, contact, and regional metamorphic events. Structure is complex, and includes polyphase Mesozoic folding and thrusting, and complex Cenozoic structures. The area continues to be seismically active. High brightness (white), high purity crystalline limestone deposits are uncommon because their formation is dependent on several geologic processes which include; 1) depositional environment, 2) contact and or regional metamorphism, 3) folding and faulting, 4) uplift and erosion, and 5) preservation through geologic time. The complex geologic history of the San Bernardino Mountains and Mojave Desert region has allowed the formation of several large high brightness, high purity limestone deposits which are currently being mined or will be mined in the future. Specialty Minerals, Inc. (formerly Ptizer), Pluess-Staufer (California), Inc. and Partins Limestone, Inc. produce high brightness, high purity limestone from several quarries in the San Bernardino Mountains. These active mines combined with undeveloped deposits controlled by Pluess-Staufer in the San Bernardino Mountains, New York Mountains, and Bristol Mountains in the Mojave area, contain proven and or indicated reserves sufficient to sustain production through the 21st century Detailed geologic mapping, intimate knowledge of stratigraphy, recognition of complex structures, sampling, drilling and assay data, are proven tools in the discovery and delineation of high brightness, high purity limestone deposits in the San Bernardino Mountains and Mojave Desert region of southern California.

Jan 1, 1995