Search Documents

By Takashi Sasaoka

About 200 M tons of coal were imported into Japan in 2007 and Indonesia was its second largest exporter, accounting for about 30 M tons (12% of the total imported coal). Indonesia produced about 200 M tons of coal, about 75% of which was exported in 2007. As the Indonesian government has decided on an energy policy wherein 33% of the country?s primary energy demand will be met by coal by the year 2025, the domestic demand for coal has increased dramatically in recent years. Over 99% of the coal produced in Indonesia comes from surface mines. However, the conditions of surface mines are worsening each year: the stripping ratio is increasing, approaching the economic ratio, and the infrastructure for coal from inland mining areas is insufficient for such intense mining operations. To meet the demand for coal in Indonesia and the rest of the world, underground mines have to be developed. However, mining engineers and/or miners in Indonesia do not have a lot of experiences, expertise and know-how concerning the plans and operations of an underground coal mine. In addition, the industry faces a lot of problems which include poor conditions such as a steep coal seam, groundwater problem, stability of highwall, etc. Under these situations, a mine targeted in this research attempts to develop a new underground mine from an open-cut highwall because the stripping ratio in the surface mining area has almost reached the limitation of economic value. This paper discusses the possible development of a new underground coal mine from an open-cut highwall by means of field observation and numerical analysis.

Jan 1, 2009

By Eugene W. Price

One of the most important fundamental characteristics of iron ore pellets is their porosity. This importance arises from the fact that the pores are the busy avenues whereby many changes are brought about in the life and form of the pellet from the time it is made until the iron it contains emerges as a molten stream from the blast furnace. As a green iron ore pellet is first heated in the drying cycle of a typical heat-hardening process, the pores act as conduits to allow the escape of steam from the water or vapor from the oil which served as binders to hold the green pellet together. After the release of the steam (or oil vapor) the pores then act as conduits whereby oxygen can enter the pellets to 1) convert magnetite (Fe304) to hematite (Fe203), if appropriate, and 2) promote solid state grain growth between adjacent particles of iron ore. The rate of oxidation and the rate of grain growth are directly related to pore size' and pore size distribution. Rate of oxidation is also directly influenced by length of pore and length of pore is obviously related to pellet diameter. It is well to keep in mind that the heat-hardening process does not harden the mineral grains themselves. What it does is weld them together to change the green pellet from a doughy mass, composed of thousands of tiny individual particles, into a strong, intergrown monolithic structure. In the blast furnace the pores again act as conduits for gases, but in this case they trans¬port reductants such as hydrogen (H2) and carbon monoxide (C0) which remove most of the oxygen from the ore. Rate of reduction is also directly related to pore size and pore size distribution.

Jan 1, 1967

A portable electronic instrument was developed which will measure change of longitudinal wave velocity with change of uniaxial stress in rock columns. The instrument is a solid-state device powered by nickel-cadmium batteries. It uses a probe of two piezo-electric crystals spaced inches apart to send and receive a pulse through a stressed rock. A one-inch cathode ray oscilloscope visually displays the longitudinal wave. A reference chart is used to find the stress. Laboratory results have indicated that the average stress on a sandstone column can be found to within 35 psi. The feasibility of using this instrument to determine stresses in mine pillars is to be studied. The instrument may be used to investigate physical properties of rock.

Jan 1, 1970

By Ronald W. May

The Lower Cretaceous McMurray Formation in northern Alberta contains bituminous sands interbedded with other sediments which form the reject encountered during mining operations. Grade prediction is based on a combination of geological interpretation, computer modelling and past mining experience. In addition to estimates for ore, an accurate estimate of "waste" or "reject," are required for Mine Planning. This study investigates the ability of point-kriging using geostatistics, to augment the existing data base of drill-holes in a study area on Syncrude's leases. This approach enables the assessment of potential "worst" case - "best" case scenarios within the context of Mine Planning.

Jan 1, 1985

By Tuncel M. Yegulalp

This article summarizes some of the results of the continuing research activity at the Henry Krumb School of Mines, Columbia University, directed towards a better understanding of the stochastic behavior of slurry flows in underground coal-slurry pipeline systems. The slurry system under consideration here replaces all conventional haulage systems between the coal face and the coal preparation plant on the surface. At the beginning of the pipeline system, flow rate and frequency of coal slurry is very closely related to the activities of production equipment at the coal face. Due to several scheduled and unscheduled interruptions in continuous miner's coal mining activity, resulting slurry flows possess stochastic characteristics. Proper understanding of these characteristics is believed to lead to a more realissic and economic design of slurry handling equipment. Fundamental ideas supported by field observations are presented and a Semi-Markov model of the slurry flows is developed. As a result of this formulation, behavior of combined slurry flows from N independent coal faces can be expressed in analytical form. The contents of a slurry surge tank receiving slurry flows with certain stochastic characteristics is investigated as a function of discharge pump characteristics and time.

Jan 1, 1981

By J. D. Grace

[Screening by centrifugal force is an unique, subject, for with the exception of only one vibrating screen presently on the market, all vibrating screens depend upon, gravity to pass material through a sizing mesh or screen cloth. This one screen that sizes by centrifugal force and utilizes gravity only to convey materiel along the screen, is the SYMONS V-Screen. This screen was designed by Loren Symons, a member of the family that has contributed so much to the metallic and non-metallic mineral processing industries. Among Symons' other outstanding contribution to these industries are the original Cone Crusher which revolutionized reduction crushing practice, the first high-speed horizontal vibrating screen, the original Rod Deck Screen, and one of the earliest vibrating Bar Grizzlies.]

Jan 1, 1965

By S. Lin

Fan stall is a notorious phenomenon with axial-flow fans. When multiple fans of this type serve a ventilation system, their mutual impacts are very complicated and not well understood. Results from laboratory experiments indicated that the immediate consequence of a fan working across its stall zone (i.e., the pronounced trough on the fan characteristic curve) is that some branches in the system may suffer abrupt and even drastic changes in air quantity and pressure. The quantity range of the fan that causes the abrupt change is called an unstable operating range. The corresponding quantity range of a branch is called a non-achievable quantity range of the branch because any quantity within this range cannot be achieved without changing some parameters of the ventilation system (e.g., branch resistances). These concepts are introduced based on the test results from tubing networks to bring attention to these important characteristics of ventilation systems.

Jan 1, 1996

By Keshavan Nair

In connection with Project Payette, which is concerned with the detection of underground nuclear explosions, it was necessary to determine the technical feasibility of constructing and maintaining a large (approximately 315 feet in diameter) unsupported underground cavity at a depth of approximately 2700 feet in the Tatum Salt Dome in Mississippi. The dimensions and the location of the cavity in the salt dome were governed by criteria laid down by the Atomic Energy Commission. Within the framework of the specified criteria, cavities of various shapes and dimensions could be utilized. One aspect of the feasibility study was to investigate the structural stability of various cavity shapes and to recommend a preferred shape. This paper summarizes the studies that were conducted to evaluate the structural stability of various proposed cavities.(l)

Jan 1, 1968

By Mike Amick

As virgin coal reserves dwindle, more and more mines are being opened in areas with previous mining. As addressed in this conference before, there are solutions available for designing mines extracting coal from reserves with known underground workings above or below the target seam. Often times, however, mining begins with limited knowledge of the underground workings. Even with careful planning, the proposed design has limited success because the ?facts? as presented during planning turn out not to be as accurate as one would like. At National Coal?s Mine #14, mining the Walnut Mountain seam, after driving the main entries in some 34 crosscuts, it was found during routine mine examinations that the pillars had separated from the roof in a few areas of the mains. Immediate roof conditions proved to be sound but questions arose concerning the stability of the main roof and floor. Core tests were done to better determine the rock strengths and characteristics. The paper presents the ideology used to tackle the effects of mining over old works in an operating coal mine. This paper discusses the analysis of the symptoms observed and the steps taken to ensure that this pillar separation was caused by the underlying old workings and that the separation was expected and controllable.

Jan 1, 2009

By J. M. Pachter

Property sales and acquisition are prominent features of today's coal industry. Before selling or buying a site, a company must know the property's economic net worth. Any evaluation of economic net worth would be inadequate if determinations of a property's environmental liabilities and costs were omitted. Short-term and long-term costs can result from liabilities related to reclamation, water treatment, subsidence, and hazardous waste disposal. A structured, interdisciplinary approach can aid in the delineation, summation, and scheduling of these costs and liabilities.

Jan 1, 1986

By Pierre J. Goossens

Since Guild 1 and Snelgrove 2 attracted our attention to the relationships between certain endogenic ore deposits and plate boundaries, an abundant flow of papers appeared in the metallogenic literature concerned with this problem and its application to mineral exploration. Some of the papers only speculate with the formation of specific type of ore deposit 3, 4, 5, 6, 7, 8, 9, 10, 11, 12 Other papers are more concerned with genetic and structural relationships between plate tectonics and mineralization 13, 14, 15, 16, 17, 18, 19, 20 They are philosophical, in that they are generalized and refer to no specific area. Yet it is true that a large part of the world mineral potential is concentrated at the convergence of oceanic and continental plates, for example, around the Pacific. Therefore, the interaction of two plates by either subduction, obduction or slippage likely has an important role for the genesis and/or the (structural) control of these "orogenic" ore deposits. If subduction is the driving mechanism for the generation of igneous rocks 21, 22 and endogenic ore deposits 18, volcanic activity and the nature of volcanic products certainly are the major geologic processes and events to be tested. Fonteilles 23 and Alsac 24 have already emphasized the important relationship between mineralization and the talc-alkaline affinity of the volcanics. The Andean orogen is one of the best areas for testing such genetic relationships. Rich and varied endogenic and volcanogenic ore deposits occur there and plate interaction is still active.

Jan 1, 1975

By Edward H. Peplow

Mr. Chairman; honored guests; ladies and gentlemen: The subject assigned me today by your committee, according to the program, is "the mineral industry and the public land law I have preferred to title the talk, "you can't mine here", for that is the essence of the message we, as an industry, have been getting from so many agencies of the federal government for so long. And, unfortunately, we can expect to hear the same message even louder and clearer -- with increasing frequency in future, unless. Every segment of the industry devotes the necessary time, energy and creative thought to combat successfully the forces that are writing and broadcasting that message. I said that agencies of the federal government are sending the message --- and this, of course, is true, the forest service, for example, and some bureaus of the department of the interior as well as others have appeared in recent years to be abiding by a policy designed to block mineral entry to as much of the public lands as possible and to wipe out existing mining claims.

Jan 1, 1967

By Robert A. Blake

Introduction Sulfide copper, zinc and iron concentrates are recovered in the 5000 ton per day flotation plant operated by Cities Service Company at Copperhill, Tennessee. The heavy-sulphide ore is first ground to 50 pct. minus 200 mesh and a bulk concentrate floated. The bulk concentrate, over 60 pct. of the ore weight, is reground to 72 pct. minus 200 mesh and then treated in a selective flotation circuit to recover copper and zinc concentrates. The tailing of selective float is the iron sulphide material source for the manufacture of sulfuric acid and iron sinter. The valuable minerals in the ore are chalcopyrite, marmatitic sphalerite, pyrite, and pyrrhotite. A typical mineralogical analysis will be found in table 1. A typical material flowsheet will be found in figure 1. Shown in the flowsheet are a scavenger float on the bulk rougher tailing and a copper-talc separation unit. At times a lead-copper separation circuit has been run.

Jan 1, 1971

By Roger S. Dewey

1.1. INTRODUCTION Despite indications of a general economic recovery in the U.S. during the mid-19801s, mine operators have not generally shared in the benefits of these reported better times. Budgets have not rebounded, borrowing is tougher, parent companies' pockets are not as deep as in previous years, and margins are not any better -- if there is any left over at all. Managing capital equipment budgets is always a challenge, and the last five years of stretched equipment lives make these decisions more tenuous. Delays and avoidance of replacements due to tough times inevitably makes those decisions increasingly difficult and usually more expensive The purposes of this paper are to present. a brief refresher outline of the fundamentals of equipment replacement analysis, to suggest a number of papers where analysis methods are explained in greater detail. and to recommend the use of a widespread microcomputer software capability (1-2-3) as the easiest path to a much-needed solution for a very difficult, and usually under-supported management decision problem 2. REPLACEMENT DECISION POLICY Investments in equipment replacements must compete for capital with all other investment alternatives. Capital for replacements of ten represents a greater commitment than do the new projects which a company might handle in a given year. But. sadly, formal policies for standardized analysis of replacements rarely exist, even in major companies. Yet this policy can be very significant in determining the competitiveness of a firm. Whereas many replacement decisions are based on cost minimization, economists and financial analysts agree that wealth maximization or return on investment is the superior criterion. Though the difference may seem slight, agreement on a firm's financial objective is vital. Replacement policy should be straight- forward. have a logical basis, and a proper level of sophistication. There are several reasons to develop a policy for replacement decision-making: [I] 1 - equipment's optimal economic life is nearly always shorter than its physical life; 2 - mine life often exceeds equipment life, so management must face these decisions routinly 3 - replacement capital costs, on an undiscounted basis, can run 25 to 75% of original capital 4 - technological changes may result in a newer machine or system which can operate more efficiently, more safely. or less expensively 5 - estimates should be made consistently in the fundamental areas of life expectancy, availability, utilization. price escalation, taxes 6 - long-term and short-term budgeting without decent data and analytical capability is nearly impossible, or at least ineffective Policy development assumptions which must be considered include: the planning horizon, cost patterns, interest rates, availability of capital, replacement vs. expansion, technology advances.

Jan 1, 1987

By B. J. Scheiner

The Bureau of Mines, Department of Interior, has been investigating the use of polyethylene oxide (PEO) as a flocculant for a variety of mineral wastes. As part of this investigation, the hydrodynamics of the flocculation process were studied. It was determined that to obtain optimum dewatering results, the factors of energy input into the stirrer, polymer concentration, and polymer dosage must be considered. Lt was found that at a given polymer concentration, there was an optimum stirrer speed and polymer dosage. With excess PEO, the amount of water removed in the trommel decreased, but no evidence for steric stabilization was observed.

Jan 1, 1987

By A. J. S. Spearing, B. Forbes, T. Kostecki, A. Hyett

Improving upon the past understanding of the interaction between installed rock bolts, the immediate roof and sidewalls is vital for the implementation of sound support system design, as this has a direct impact on rock-related safety. This is the primary goal in rock-bolt-related research. The earliest research in this field concentrated on limited laboratory and in situ measurements accompanied by theoretical analyses, based on the Kirsch equations. This represented the initial insight into understanding relative ground movements and their impact on primary support. However, these studies were far from complete. More recently, major technological advances in computing power within the mining industry has changed the scope from theoretical analysis to computer simulation. Even with these advancements our understanding of rock bolts in situ and in the laboratory has not progressed, particularly concerning bending and shear. To measure the behavior of rock bolts, the widely accepted practice is to populate the bolts with an array of strain gauges. Historically, resistive foil strain gauges or long displacement sensors have been used. Additionally, all instrumented rock bolts have used only two diametrically opposed slots. Rock bolts instrumented with these methods have significant shortcomings, one of which is the inability to capture shear and bending. The shearing and bending of rock bolts are particularly common in tabular soft rock mining, such as coal mining. This paper discusses the use of three slotted rock bolts, cut diametrically 120º apart, and two new optical fiber technologies populated along the entire rock-bolt length.

Jan 1, 2015

By Langtry E. Lynd

The titanium industry is based on the unique properties of titanium dioxide and titanium metal. Because of its whiteness, high refractive index and resulting light scattering ability, titanium dioxide in its two main allotropic forms, rutile and anatase, is the predominant white pigment for paints, paper, plastics, rubber, and various other materials. Titanium metal, because of its high strength/weight ratio and resistance to corrosion, is widely used for aircraft, both in airframes and engines, for powerplant surface condensers, and a wide variety of chemical processing and handling equipment. U.S. production of titanium dioxide pigment in 1979 was about 658,000 tons - 2/, valued at about $770 million. Net shipments of titanium mill products were around 19,000 tons, worth about $380 million. These two major uses account for over 96% of domestic titanium consumption. The third largest application, the use of rutile for coating welding rods, required about 9,500 tons of rutile concentrate, worth about $4 million. Other applications of titanium-bearing raw materials include the manufacture of titanium carbides, ceramics, and chemicals, and the recently developed use of ilmenite as a substitute for barite in well-drilling muds.

Jan 1, 1980

By M. J. Raffaldi, L. A. Sandbak, K. K. Dehn, S. N. Warren, J. B. Seymour

"Confidence in the design and stability of an undercut cemented rockfill (CRF) span requires a thorough understanding of its emplaced material properties. The unconfined compressive strength (UCS) of cast 6×12-inch QA/QC cylinders is typically used as an index test to track the performance of a backfill plant. However, these strengths need to be adjusted for oversize aggregate removal and sample size effects if used to estimate the emplaced UCS. UCS testing of 6×12, 12×24, and 18×36-inch cast CRF cylinders was used to quantify the relationship between readily available 6×12-inch QA/QC strength data and the emplaced UCS. Test results indicate that the UCS of 18×36-inch cylinders is roughly 40% of the 6×12-inch UCS for similarly compacted samples. Mine QA/QC data indicate that the UCS of CRF is highly dependent on the degree of compaction as measured by bulk density. Based on these results, knowledge of the emplaced CRF density compared to 6×12-inch QA/QC density is also necessary to estimate the emplaced UCS. The scale effect reported in this study is more pronounced, compared to current understanding of backfill properties discussed in the literature, and underscores the need for further site-specific testing. INTRODUCTION The National Institute for Occupational Safety and Health (NIOSH) Spokane Mining Research Division (SRMD), in cooperation with Barrick Gold Corporation, is conducting research with the goal of determining a relationship between 6-inch QA/QC cylinder strengths and the in-place strength of cemented rockfill (CRF). CRF cylinders with dimensions (diameter × length) of 6×12, 12×24, and 18×36 inches were cast onsite at the Turquoise Ridge Joint Venture (TRJV) and Cortez Hills Underground (CHUG) mines using CRF mixed at the mines’ respective batch plants. UCS tests were performed after 28 days of curing to estimate the size correction factor for each mine’s CRF. This paper presents an overview of the mix designs, sample collections, testing methods, test results, and an estimate of the UCS size correction factor for CRF at these mines. BACKGROUND Underhand cut and fill mining methods utilizing cemented backfill are common in underground metal mines in the United States. These methods are advantageous for controlling weak or highly stressed rock mass conditions by creating an engineered material that can be placed in openings, forming a beam that provides a safe, stable back for the next undercut. Increased use of underhand methods in the last 30 years has greatly improved safety in many cut-and-fill mines. However, with the continual push for more efficient and cost effective mining, there is a need to thoroughly understand the geotechnical properties of cemented backfill to assist in designing safe, stable openings while optimizing costs and production schedules."

Jan 1, 2018

By Robert M. Dreyer

The first time that a geologist is confronted with the necessity of evaluating a lateritic ore deposit, he may feel that nothing could be easier. Why should there be any problems in making an economic evaluation of a relatively flat-lying, surficial ore body? After several hundred thousand dollars worth of frustrating work often culminating in a series of non-reproducible data - the evaluator may be a sadder and wiser man. This paper will try to illustrate why the evaluation of lateritic bauxite and nickel deposits is among the most difficult problems confronting an economic geologist - and, more especially, how this problem can be solved. Volumes have been published on descriptive and genetic studies of lateritic ores. Obviously, there is time today only for the briefest description of such an ore body. The laterite is a soil formed under tropical conditions and resulting in the concentration, within the soil zone, of certain tri-valent metals.- especially, aluminum and nickel. The soil zone is divided into two parts: (a) the true soil or lateritic zone and (b) the zone of, partially altered bed rock or saprolite. It is important to remember that, whereas bauxite generally is confined to the laterite zone, nickel deposits occur in both the laterite and

Jan 1, 1977

By R. V. Ramani, S. Shankar

The phenomenon of re-entrainment is seen in environments such as sand dune formation, soil erosion, fugitive dust emission and the spread of radionuclides from accidents involving nuclear weapons. A thorough review of existing literature reveals that work on re-entrainment of dust in mine atmospheres is scant. The present study was undertaken as a part of ongoing research at the Generic Mineral Technology Center on Respirable Dust at the Pennsylvania State University on the development of methods to predict ambient dust concentrations in mine atmospheres (Ramani, 1983). The contribution of re-entrainment to the spatial and temporal concentration of dust in mine airways is being studied. The research has included wind tunnel and in-mine studies. A set of seven experiments was performed under controlled conditions in the US Bureau of Mines' Lake Lynn Laboratory mine. Two types of source coal dust, anthracite and bituminous, were subjected to various airflow rates and were subjected to walking by two different individuals. Six sets of instruments were used along the test section for sampling airborne particles. The average air velocity just above the coal dust bed varied between 2.1 to 3.2 m/sec. Due to re-entrainment as a result of the airflow conditions, the average respirable dust concentration in the center of the mine airway increased to 0.09 mg/m3 (standard deviation = 0.03 mg/m3) from an initial value of 0.02 mg/m3. The concentration of all (total) airborne dust increased to 0.17 mg/m3 (standard deviation = 0. 10 mg/M3) from an initial value of 0. 02 mg/m3. The action of people walking, however, caused higher amounts of re-entrainment. The average concentration of respirable and total dust at the center of the mine airway increased to values of 0. 28 mg/m3 (standard deviation of 0.12 mg/m3) and 1.53 mg/m3 (standard deviation of 1.0 mg/m3), from initial values of 0.03 and 0.05 mg/m3, respectively. It was observed that the dust concentrations were much higher near the floor, immediately at the end of the coal-dust bed. Depending on the level of activity and the amount of dust deposited in the mine airways, re-entrainment may become an important source of airborne dust in areas away from the point of actual mining.

Jan 1, 1996