Search Documents

By D. Bahrami, G. Danko, W. Asante

"It is prudent to interpret atmospheric monitoring signals in real-time for checking the safe limits of the air conditions in underground mines. In gassy mines, such real-time evaluation increases the safety of operation. In all mines, the continuous monitoring and evaluation contribute to maintaining air conditions to be within healthy and safe limits. Signal interpretation for safety conditions in mines is difficult for many reasons. An increase of hazardous contaminant concentrations can be predicted by signal pattern recognition, root-cause analysis of rapid changes toward deterioration and forward prediction in time using algorithms and numerical models. This paper focuses on analyzing signal patterns to recognize dangerous trends as well as forward predicting the various environmental and working conditions that may affect safety in underground mines. Efficient numerical ventilation model with heat and gas contaminant simulation components is needed for the analysis of real-time atmospheric monitoring data. Computational speed enhancement methods are discussed and tested in numerical examples, using the Jacobian sensitivity matrices for signal propagation prediction. INTRODUCTION The focus area of this paper is mine safety, related to hazardous atmospheric conditions in a mine ventilation system. Improvements by recognizing safety hazards caused by heat of combustible gases or the accumulation of poisonous gases in a mine are addressed. The recognition of safety hazard by manual evaluation is difficult because of the complex nature of information and the large amount of monitored data from measurement by atmospheric sensors such as air velocity, pressure, hazardous gas contaminants and temperature. In order to recognize problem-causing trends, it is necessary to evaluate continuously individual measurement data from the Atmospheric Monitoring System (AMS) of the mine during their time-dependent variations. In addition, the combined effects of various signal trends need to be simultaneously interpreted in their cross-effects. It is very difficult to foresee the possible outcomes of intertwined signatures of various problems by continuous human observation. For example, a steady, continuous methane concentration measurement together with a sharp drop in barometric pressure from the AMS sensors may be a case for worry in future time due to pressure-induced methane increase from the coal seam or the gob (Danko et al., 2013). This future increase can be predicted by a time-dependent Ventilation Air Model (VAM) and its surrogate Air Parameter Predictor Solver (APPS) model. A calibrated VAM or APPS model can indeed predict a likely methane concentration variation in future time as a function of previous and new air pressure as well as air velocity (Danko, et. al., 2013). Such a future trend, however, cannot be seen from the raw measurement data."

Jan 1, 2017

By D. Scott Barr

The Zarafshan/Newmont Joint Venture operates the Muruntau heap leach project, located in the Kyzylkum desert of central Uzbekistan. The mine produces more than 12.4 t/a (400,000 oz/year) of gold from low-grade oxide ore stockpiles adjacent to the Muruntau open pit. It is op¬erated by the Navoi Mining and Metallurgical Combine and is one of the largest gold resources known (Fig. 1). Since commissioning in 1995, total heap leach production has exceeded 21 t (675,000 oz). The joint venture uses four-stage crushing and screening to produce a final product for heap leaching, Merrill-Crowe processing and local refining.

Jan 1, 1998

By Inoka E. Perera, Michael J. Sapko, Marcia L. Harris

Experiments conducted with limestone dusts and dolomitic marble dusts have indicated that when rock dust is wetted and subsequently dried, it becomes a solid, non-dispersible cake. However, in order to be effectively inert a coal dust explosion, rock dust must be able to disperse as individual particles to air. To counteract this, rock dust manufacturers created treated rock dusts that will resist caking after moisture exposure. National Institute for Occupational Safety and Health (NIOSH) researchers conducted a series of laboratory-scale experiments on four base rock dusts and their treated counterparts to assess the effectiveness of various anticaking additives after being exposed tomoisture and then dried. The dusts were exposed tomoisture using humidity cabinets having a high relative humidity (99% RH) and by also exposing the rock dust bed to water through bottom wicking. The dusts were then evaluated for dispersibility after drying using the NIOSH-designed dust dispersion chamber. The anti-caking additives were different concentrations of stearic acid, oleic acid, and xylene-based surfactants. All results were compared to a reference rock dust used to conduct large-scale experiments in the Lake Lynn Experimental Mine (LLEM), Fairchance, PA. When the untreated dusts were dried after exposure to moisture for 1 day, no dispersion was measured. However, rock dusts treated with anti-caking agents were readily dispersible even after exposure to moisture for 6 months. This report details the analysis and characterization of anticaking additives using the NIOSH-designed dispersion chamber and the 20-L explosion test chamber.

Apr 12, 2021

By L. Yuan, A. C. Smith

MFIRE, the mine-fire simulation program of the U.S. National Institute for Occupational Safety and Health (NIOSH), is widely accepted as a standard for assessing and predicting the impact of a fire on the mine ventilation system and the spread of fire contaminants in coal and metal/nonmetal mines. MFIRE has been used by U.S. and international companies to simulate fires for planning and response purposes. It is a dynamic, transient-state, mine ventilation network simulation program that performs normal planning calculations. It can also be used to analyze ventilation networks under thermal and mechanical influence, such as changes in ventilation parameters; external influences, such as changes in temperature; and internal influences, such as a fire. The program output can be used to analyze the effects of these influences on the ventilation system. Since its original development by Michigan Technological University for the former U.S. Bureau of Mines in the 1970s, several updates have been released. In 2012, NIOSH completed a major redesign and restructuring of the program with the release of MFIRE 3.0. MFIRE’s outdated Fortran programming language was replaced with an object-oriented C++ language and packaged into a dynamic-link library. However, the MFIRE 3.0 release included no change or improvement to the fire-modeling algorithms inherited from its previous version, MFIRE 2.20. This paper reports on improvements that have been made to the fire-modeling capabilities of MFIRE 3.0 since its release. These improvements include the addition of the t-squared fire as a new fire-source model and the ability to include available heat-release-rate versus time data, the addition of a moving fire source for conveyor-belt fire simulations, improvement of the fire location algorithm, and the identification and prediction of smoke-rollback phenomena. All of the improvements discussed in this paper will be included in MFIRE 3.1 and released by NIOSH in the near future.

Jun 1, 2016

By A. S. Azman

In collaboration with Kennametal Inc. and corry rubber corporation, the U.S. National Institute for Occupational Safety and Health (NIOSH) developed a drill bit isolator to address noise overexposures associated with roof bolting machines in underground coal mines. NIOSH laboratory studies confirmed that the drill bit isolator reduces noise during drilling. Field studies were needed to confirm that a noise reduction could be obtained under working conditions and that the device was sufficiently durable. This paper reports results of field tests of the device conducted at five underground coal mines. Noise reduction was assessed by comparing the operator?s noise exposure during drilling with and without the drill bit isolator. Durability was assessed by recording the number of holes and total feet drilled with each bit isolator until either the test period ended or the device failed. The results from these tests showed that the device is an effective noise control in a mine environment. The field-tested drill bit isolators provided a noise reduction of 3-5 db(A). Of nine devices tested for durability, five exceeded 610 m (2,000 ft) drilled and two exceeded 762 m (2,500 ft) drilled before failure. Durability issues found in the field tests led to final production optimizations that have resulted in a commercially available product for drilling with 35-mm- (1.3-in.-) diameter roof bits and hexagonal drill steels.

Jan 1, 2012

By M. D. Banghart

The Republic of South Africa is an outstanding example of the benefits to a new land by the application of individual enterprise, capital and know-how. While South Africa was colonized by European and Bantu people some 300 years ago, it was only 70 to 80 years agog when diamonds were discovered at Kimberley and gold on the Witswatersrand, that the mining, industrial and commercial potential of the country began to emerge. South Africa s national income rose from R1, 200 million in 1945 to over R4 billion in 1960 (1R = 10 shillings = $1.40 U. S.) The annual national income per head of population -- including all races -- is currently R254 (£127) This compares with £24 for India., £30 for Nigeria, and £50 for Ghana. Allowing for the increase in population, the increase in real income per head of population was about 40% during the past 15 years.

Jan 1, 1962

By V. A. Shea-Albin

Sandstone escarpments surrounding western coal-bearing plateaus serve as critical habitat for animal species. Effects of mining subsidence on escarpment stability are not well documented; therefore, regulatory agencies may limit extraction of coal reserves underlying escarpments. Because millions of tons of this coal exist on Federal Lands, associated public revenues from Federal royalties, and valuable coal reserves, risk being lost. The U. S. Bureau of Mines is using numerical modeling techniques to analyze effects of subsidence on escarpment stability. Finite element models that incorporate bedding plane slip, gob formation, and movement along joints simulate escarpment subsidence observed in the field.

Jan 1, 1994

By John Barakso

The Sam Goosly or Equity silver deposit is fundamental- ly a discovery based on the analysis and interpretation of reconnaissance geochemical samples. The discovery was made by Kennco in an area of heavy forestation and wide- spread cover by thin glacial debris. No major mines had been discovered in the vicinity of the discovery prior to the geochemical reconnaissance, and the interpretation of the geochemical results therefore was based on data available through geologic mapping and the sample collection process. In the period 1959-1961, PE. Hirst and his crew, in 1962- 1965 P.T. Blackand his crew, and in 1966-1967 C.S. Ney and P.T. Black and their crew collected geochemical samples from the area of what is now the ore body. Several of these samples were compiled and reanalyzed in the winter of 1966- 1967 for various trace elements, including fluorine. A strong, almost 16-sq-km (10-sq-mile) fluorine anomaly was projected along with a very weak heavy metal anomaly. On the basis of this anomaly, a chalcopyrite-bearing quartz monzonite was discovered in 1967. This was a misleading, noneconomic discovery not associated with the Sam Goosly discovery. The interpretation of the geochemical data by Barakso that summer indicated that another source was responsible for the fluorine anomaly. The conclusion was based on the assemblage of trace elements. Therefore C.S. Ney recommended further regional soil sampling to check the original data. The early results of this follow-up sampling found over 33 ppm silver. First float, then ore outcrop was found in the area of the silver anomaly. The attached reprints complete the development of the property after the discovery of the outcrop of ore.

Jan 1, 1990

By C. B. Henderson

The development of slurries of coal and water as a boiler fuel replacing No. 6 fuel oil has been actively pursued at the Atlantic Research Corporation since 1976. Funding for this effort has been provided by the U.S. Department of Energy, the Electric Power Research Institute, and by corporate funds. The name ARC-COALTM has been selected for these slurries. Stable coal-water slurries with bone-dry coal loadings between 62% and 77% have been prepared, evaluated rheologically, and successfully burned in an experimental furnace without the assistance of other fuels. The advantages and properties of these slurries, including combustion results, are reviewed. Also discussed is the pilot line used for processing barrel quantities of fuel and a pilot plant capable of processing 600 bbl/day, currently being designed.

Jan 1, 1982

By C. B. Manula

This paper presents the results of an application of the PSU/USBM Open Pit Materials Handling Simulator (1) to a large stripping mine in the Southwestern Coalfield. The specific objective of the study was to demonstrate the application of the simulator to a complex multi-pit operation, with emphasis on simulating short term and long term production plans recommended for the mine by Theodore Barry Associates (2). Mine Description The mine is located in the Southwestern Coalfield, which encompasses parts of the states of Utah, Arizona and New Mexico. The lease area presently covers 121500 x 103 m2 (30000 acres) in a strip 37.007 x 103 m (23 miles) from north to south and up to 1609 m (1 mile) in width, located at an elevation above 1525 m (5000 ft). Three gently dipping coal seams are present, of which the upper seam (#3) averages 0-5.5 m (0-18 ft); the intermediate seam (#2) averages 0-1.2 m (0-4 ft); and the lower seam (#1) averages 0-2.4 m (0-8 ft). Overburden is mixed sand, gravel, calcareous clay, caliche and sandstone, with calcareous shale and sandstone burden between seams. Where the seams are covered by less than 6.1 m (20 ft) of overburden, they are generally weathered and oxidized and are not extracted. Stripping ratios have ranged from 3.5 to 6.0 with an average of 5.4. All future plans were based on a stripping ratio of 5.3.

Jan 1, 1979

By Wenbing Guo, Gaobo Zhao, Erhu Bai, Brijes Mishra

"Violent damage to overlying strata can occur above the large mined-out space left by high-intensity longwall mining. For the safe mining under the aquifer and surface water body, it is imperative to investigate the criteria of overburden failure degree due to high-intensity mining. In this paper we present the characteristics of high-intensity longwall mining panels and overburden critical failure. Based on the geological and mining conditions of a high-intensity mining panel, 3D numerical models that consider the maximum horizontal principal stress and minimum horizontal stress and their orientations with the panel advance direction were established by using the 3DEC software. Sizes of the panel reaching the critical failure of the overburden under different mining thicknesses (3.5 m, 6.5 m, 9.5 m, 12.5 m, and 15.5 m) were analyzed. Further, criteria of overburden critical failure were proposed for the high-intensity mining. The coefficient of overburden critical failure (Cf) is the ratio of the strike length (Ls) to the mining depth (H). Through curve fitting analysis, a fitting equation between Cf and mining thickness was obtained. The results showed that overburden failure criterion with high-intensity mining panel is 0.38 = Cf = 0.97 with different thicknesses. Field measurements validated the results from the numerical models.INTRODUCTIONHigh-intensity longwall mining refers to a coal mining method with thick coal seam, large panel width, fast face advance rate, and severe damage to the overburden and surface in China (Guo et al., 2018). Violent movement of the roof rock and severe damage to overlying rock strata occur in the large mined-out space left by a high-intensity longwall mining panel, which is a 3D (three-dimensional) structure layout with highly non-uniform stress distribution. Recognition of such fact a will facilitate this overlying rock strata failure problem investigation (Peng et al., 2019).The studies of overlying strata failure due to longwall coal mining have been reported by some scholars with different methods. Kang et al. (2018) studied the sudden massive roof collapse during longwall coal retreat mining by a large-scale two-dimensional physical model and a UDEC numerical model. Ghabraie et al. (2015) researched the mining-related strata movement by applying the three-dimensional laser scanner, optical transducer, and digital image processing techniques to two-dimensional physical models. Wang et al. (2015) analyzed the structural characteristics and fracture failure process of overlying hard and thick main roof by a 3DEC numerical model; this study also investigated the geostress reduction and permeability enhancement redistribution of the adjacent coal measure strata by FLAC3D. Guo et al. (2012) performed a three-dimensional finite element analysis and shared some insights into the dynamic interaction between mining induced strata stress changes, failures, and gas flow patterns. Meng, Shi, and Li (2016) proposed a 3D coupling model between stress and permeability, investigating the dynamics of a stress, permeability coefficient using FLAC3D. Khanal, Guo, and Adhikary (2019) used the 3D numerical modelling approach (COSFOW) to investigate the strata deformation and the change in permeability in the overburden strata due to the underground extraction. However, few studies considered the influence of the horizontal stress on overburden failure in a high-intensity longwall mining panel, and the critical failure criteria of overlying rock strata is unclear."

Jan 1, 2019

By John Dodd

Advances in the technology of abrasion resistant irons and steels, which could help in combating abrasion and wear in mining operations, are reviewed. Nodular irons alloyed with nickel or copper and molybdenum, with acicular, bainitic or bainitic-martensicic microstructures are described. These alloy irons combine excellent castability and relatively easy machinabilitv with good resistance to wear. Recent progress in the development of high chromium molybdenum alloy irons is outlined, by which high temperature heat treatment of massive castings can be eliminated, alloy costs can be reduced and cracking problems avoided. Data is also given on the erosion-corrosion resistance of these irons. Trends in the development of improved cast steels are outlined. Factors influencing the toughness and abrasion resistance of manganese steels are considered. The 6% Mn 1% Mo manganese steels are shown to have a useful combination of toughness and abrasion resistance. Composite castings are seen as a means of com- bating abrasion in applications involving severe impact. A brief appraisal is given of recently developed martensitic wrought steels with improved weldability.

Jan 1, 1981

By M. D. Ballain, V. C. Storhok, B. Pesic, J. C. Sever

Northwest Alloys, a wholly owned subsidiary of Alcoa, produces magnesium from dolomite by reduction with ferrosilicon and aluminum. This process produces alkaline by-products in quantities that allow their consideration for use as commercial by-products. Two such products are dicalcium silicate slag, Di-Cal, and magnesium oxide condensate, MgO. The alkaline properties of these materials offer acid neutralizing capability comparable to the traditionally used lime, therefore, warranting a study for their use in applications where the neutralization of acidic waters or process solutions is required, such as treatment of mine waters. In this ongoing study, three mine waters (Bunker HillMine, Berkeley Pit, and Blackbird Mine) were selected for treatment with Di-Cal and MgO. Lime was used as the background control. The solid precipitates were subsequently contacted with pure water at four different pH conditions for stability testing of prepared metal precipitates (expanded TCLP). It was found that neutralization with Di-Cal results in precipitates which are of equivalent to superior stability than those from lime treatment.

Jan 1, 1999

By S. D. Bearden

China was the world’s leading producer of barite during 1995 with 35%. The United States followed with14%. India produced 9%. Other producers included Morocco, Turkey, Mexico and Germany. Domestic production of barite during 1995 was estimated to be 600 kt (660,000 st). Nevada produced 85% of the total. Georgia was the second leading barite-producing state. The United States is the world’s largest consumer of barite. During 1995, it used 1.6 Mt (1.8 million st). US reliance on imported barite during 1995 was about 63%of total consumption, according to the US Geological Survey.

Jan 1, 1996

By Sam Rosenblum

The anomaly ratio is obtained by dividing the analyzed value of an element by the anomaly threshold value of the element. The sum of anomaly ratios for all anomalous elements in a sample may be compared with similar sums for other samples, so that the samples having the greatest anomaly-ratio totals can be recognized easily. In partial or full-suites-of-ore-elements the use of anomaly ratios is more meaningful than analyzed values because the ratios quickly indicate anomalous elements and call attention to samples and localities that should be investigated.

Jan 1, 1980

By C. P. Lazzara, R. W. Pro, A. C. Smith

The U.S. Bureau of Mines conducted a study to evaluate the effectiveness of automatic water sprinkler systems in the extinguishment of incipient conveyor belt fires under ventilated conditions. Large-scale experiments were conducted using a double strand conveyor belt configuration. Standard response, pendent-type sprinklers, with activation temperatures of 100°C, were installed above and between the two strands of belting, in accordance with Federal standards for sprinkler system installations in belt drive areas. Experiments at airflows of 1.1 and 4.6 m/s showed that the sprinklers activated later, the peak heat release rate was larger, and more betting was consumed at the higher airflow. In experiments with 74°C, fast response, directional sprinklers, the sprinklers activated at the same heat release rate for both high and low airflows, but the peak heat release rate and amount of bett consumed was slightly higher at the lower airflow. Experiments were also conducted with 100 °C, standard pendent sprinklers installed above the top belt, in accordance with the National Fire Protection Association (NFPA) Standard 123 for sprinkler system installations in conveyor belt drive areas in underground coal mines. In these experiments, the heat release rate and amount of betting consumed was larger at the higher airflow.

Jan 1, 1995

By Marcos Vieira, Gil Vilela, Wanderson Silvério, Livia Faustino, Pierre Fernandes

New global industry standards and regulatory changes regarding mining tailings management are driving installation of tailings filtration plants to decommission existing tailings dams and implement dry stacking. Target of this project was to reduce ultrafine slime tailings deposition. Previous investigation at Samarco concentrator has showed a 35% decrease in tailings filtration throughput when feeding a mix of 95% flotation tailings with 5% slime tailings (compared with 100% flotation tailings), also worsening geotechnical aspects such as material workability during dry staking. Industrial trials using a proper filter aid at tailings filtration plant feeding a mix of 94% flotation tailing and 6% slime tailing (equivalent to 30% of total slime generation) have provided filtration performance maintenance (throughput and cake moisture), and dry stacking the dewatered material. Results achieved will enable life expansion of existing slime disposal structures, as well as potential life of mining extension. Furthermore, reagent chemistry influence is discussed by the light of geotechnical aspects, which has been showing improved KPIs, such as workability, compressibility and permeability.

Feb 1, 2025

By Jerry C. Tien

The rare earth elements (REEs) are a group of 17 chemical (metallic) elements which appear in the periodic table. The group consists of 15 lanthanide elements along with yttrium and scandium (Table 1). They share many similar properties, which is why they occur together in geological deposits. Although commonly referred to as rare, they are really quite common; the reason they are perceived as rare is because it is not common to find them in commercially viable concentrations. These metals are critical to advanced technology, ranging from smart phones to global positions system (GPS) receivers, medical devices and jet engines. They are critical in green, high-tech and defense industries (Fig.1 and 2). Although there have been increasing efforts to find alternative supplies, these efforts have been complicated by the pollution that rare earth mining and processing creates. To extract rare earths minerals from mined ore is a complicated and costly process. The ore is first mined through normal mining process, the bastnaesite, which generally contains a number of minerals of little value, is first removed through a floatation process. The bastnaesite containing the REEs is further separated into their respective pure forms in a separation plant using acid and various solvent extraction separation steps. Each element has its own unique extraction steps and chemical processes. At times, these elements, in the form of oxides, will require reprocessing to achieve ideal purity. The last steps would be to further process into metals first, then alloys for various applications. The entire process takes approximately 10 days. The mining and processing of REEs, if not carefully controlled, can create environmental hazards. This is one of the reasons the Mountain Pass Mine in California was closed down in the 1980s.

Dec 1, 2013

By M. S. Davis

The Tek Process can produce masonry products such as bricks, roof or wall tiles, and block from virtually any inorganic waste. In the process the aggregate raw materials, portland cement, water and common chemicals are first mixed together; then mechanically subjected to several thousand pound pressure per square inch. This causes a novel chemical reaction between the cement, chemicals and water; producing the "patented" Tek adhesive binder which holds the aggregate together in a stone-like mix. Simultaneously, the desired product shape is formed. The building modules can have strengths of 8000 p.s.i. (pounds per square inch) with completely sound aggregates utilizing air curing for a period of 28 days. With most aggregates, 3000 p.s.i. is achieved within 24 hours. Eventual strengths usually exceed 5000 p.s.i. with almost any raw material. Water absorption ranges from 5-7.5 percent. Both absorption and strength figures are superior to the most rigid of any and all A.S.T.M. specifications for the highest quality bricks. In most locations, the product (when brick shaped is called Tekbrik) can be produced significantly more economically than can comparable grades of clay or other bricks, be- cause almost any inorganic waste materials or pollutant can be used as a raw material. The process results in a lower manufacturing cost as compared to clay bricks; fuel cost to operate a clay kiln represents a substantial portion of the total cost. Capital expenditure for a Tek plant also is lower due to the large investment in clay kilns. Transportation savings also are important, clay brick factories must be very large because the kilns are uneconomical unless they are large. Most bricks are manufactured at the sites of clay deposits in relatively uninhabited areas. The cost of transportation to the job site represents a considerable percentage of the selling price.

Jan 1, 1974

By Emmanuel V. Manlapig

The variables involved in a complex process like flotation can be classified as follows: a. Disturbance variables - which are undesired properties of the process input which affect the value of the process output but which are not subject to adjustment. They are the result of changes in the properties of the feed, like changes in head grade, flow rate, fineness of grind, etc. b. Manipulated variables (sometimes referred to as process variables or control variables) -which are those that are adjusted - reagent addition, aeration, pulp level - in order to compensate for the disturbances in the properties of feed. c. Performance variables (sometimes referred to as controlled variables) -which are those whose values measure the performance of the process. They are properties of the process output such as grade and recovery. The function of a control system is to maintain the process performance equal to the control objective in spite of the disturbances by adjusting the manipulated variables. Attempts at developing automatic control systems for mineral processing operations date back to the thirties and in many of these attempts the results were not surprisingly poor and un-stable. The poor results brought indifference and suspicion towards automatic control on the part of operators and management. The reasons for the apparent failure of these attempts were two-fold: a. the lack of adequate understanding of the behavioural responses of the process from the control point of view, and b. the lack of reliable control instrumentation which could withstand the harsh environment in mineral dressing plants. Many operators had accepted the fact that control of mineral dressing could be best conducted manually. In the case of flotation circuits, control had been virtually based on the skill and experience of operators particularly their ability to identify and rectify poor flotation performance aided by results from the laboratory (chemical) analysis of regularly collected samples from strategic points in the circuit which are at best, hourly collected samples.

Jan 1, 1978