Search Documents

By W. B. Greer

The performance of seals in boreholes, shafts, and tunnels is an important concern in mine safety, in the control of effluents from operating and abandoned mines, and in the underground containment of hazardous wastes (Einarson and Abel, 1990; Mining Waste Study, 1988). Despite the clear need for effective seals, few documented test results are available concerning the performance of in-situ seals. Some evidence indicates that horizontal or near-horizontal holes are especially difficult to seal properly (Kelsall and others, 1982). This research involved the installation, extensive hydraulic testing, removal, and post-test examination of a l0-cm-long by 10-cm-diameter cement grout seal in a near-horizontal borehole in limestone. The work was performed in an underground mine on Marble peak in the Santa Catalina Mountains, Arizona. A test hole was diamond cored in the re-crystallized limestone of the Escabrosa formation. The hole is 33.24 m long, 10 cm in diameter, and dips at 10.4 degrees. The hole extends between two drifts and thus is accessible from both ends.

Jan 1, 1992

By Kadri Dagdelen

The importance of factoring mining dilution into feasibility stage ore reserve estimates is discussed. An example that relates the issue of mining dilution to the size of smallest volumes that can be mined selectively is given. Relationship between the size of the selective mining units (SMU's) and the variance of their average grade is presented. The concept of variance reduction and its use in factoring mining dilution into geostatistical ore reserve estimation is described. An approach to estimate variance reduction factor by way of conditional simulation is introduced.

Jan 1, 1996

By X. Cai, L. Jiang, G. Fu

A process for recovering manganese from low-grade manganese oxide ore through a reduction acidolysis-selective leaching method is investigated. Two types of biomass, sawdust and straw, were used as reductants. Reduction acidolysis, using concentrated sulfuric acid, was used to disrupt the structure of the biomass, allowing the biomass to be hydrolyzed into monosaccharides. Analysis by X-ray diffraction revealed that Mn2O3 was reduced to MnSO4. Then, in the selective leaching process, iron was removed through the formation of goethite. The optimized experimental parameters are as follows: reductant to ore mass ratio of 0.4, sulfuric acid to ore mass ratio of 0.9, water to ore ratio of 0.5, aging time of 18 h, leaching temperature of 95 °C, leaching time of 90 min, and solution pH of 2.5 to 2.8. Under these conditions and using sawdust as the reductant, the manganese leaching efficiency and iron removal efficiency were 91.8 and 99.2 percent, respectively.

By C. S. Wageman

Staying competitive in the highly aggressive Powder River Basin is a challenge facing all operators. Any advantage that a mine utilizes to improve productivity and reduce costs could mean the difference in the tight spot coal market. Technological advances in mining equipment and data acquisition at the Eagle Butte Mine in Gillette, Wyoming result in productivity gains and increased maintenance awareness. A new overburden haulage truck fleet with an onboard payload and fault monitoring system interacts via telemetry with the loading shovel and PC's located in production and maintenance offices, enabling staff to monitor production and maintenance on a real-time basis. This paper will describe the system and highlight the benefits realized as a result of its implementation.

Jan 1, 1996

By Norbert Patzelt, Johann Knecht

Future ore reserves of major gold producers in North America and elsewhere will consist of refractory gold ores. About 60 % of the current U.S. gold production is mined in Nevada. Several of the large gold operations in this state indicate that 40 to 90 % of their future ore feeds will contain refractory gold. To com­pound problems, average head grades for refractory U.S. gold ores had fallen from 8 - 9 g/mt to about 4 g/mt by 1991. In Latin America, 52 % of the gold operations will require milling for optimal recovery. Deeper reserves are, like in North America, refractory. Therefore a special treatment process is needed in order to allow for the gold ore to be leached downstream in a conven­tional cyanidation process for a high gold recovery. There are several options available for this oxidation process like treat­ment of the gold bearing ore in pressure oxidation, in a biooxi­dation or in a roasting plant depending on the reason for the refractoriness. If organic carbonaceous matters and sulfides are the prima­ry reasons for the refractoriness, whole ore roasting is a pre­ferred method for the treatment of this type of ore. Since dry ore is to feed to the roaster, a dry grinding mill is advantageous. For the dry grinding system, the moisture content and the ore char­acteristic is of importance. Those parameters decide the mode of the grinding system. For autoclave systems common wet grind­ing systems can be applied. This paper deals with technical aspects for dry grinding plants and gives an outlook on and pos­sibilities for new grinding systems.

Jan 1, 1996

By R. L. Zick

The High Density Sludge Process was originally developed by Bethlehem Steel Corporation for use on acid mine drainage and diluted waste pickle liquor discharges requiring continuous chemical treatment systems. This work began in the early 1970s and was first put into practical use around 1973. To date there are approximately 15 operating systems which have been installed on mine drainage in the United States, and another 10 systems worldwide. Dense Sludge is an innovative and improved method for treating acidic metal bearing streams in a manner which minimizes the volumetric generation of sludge for disposal. The technology utilizes a sludge recycle process which forms particles that have a low affinity for water, unlike conventional metal hydroxide solids which contain tightly bound interstitial waters. Typical acid mine drainage streams contain high sulfate concentrations which combine with calcium ions in lime based treatment systems to form gypsum crystals. The physical form of this gypsum is radically altered when the Dense Sludge process is utilized compared to the form generated in conventional lime treatment systems. The characteristics of the metals particles are also changed in this process, as the metal hydroxides are converted to metal oxides. Slides No. 1 and No.2 show scanning electron micrographs of conventional and densified sludges illustrating these differences. The magnification used was 300X. The dense sludge particles settle faster, dewater more readily, are more easily pumped, and hold much less water than conventional precipitates. In some cases, because the metal content of the sludge is more concentrated, it can be economically recovered.

Jan 1, 1998

By J. Bilant, B. Carlson, N. Gow

High Pressure Grinding Roll (HPGR) technology has been evaluated to replace tertiary cone crushing at Coeur Rochester operations (Coeur Rochester, Inc.) as an opportunity to improve silver recovery. In 2016 and 2017, onsite and third-party pilot programs were initiated to evaluate the impact of metallurgical recovery and heap leach performance of crushed product generated by an HPGR. In 2018, Forte Dynamics evaluated the HPGR laboratory metallurgical data from Coeur Rochester and all third parties to develop field-scale leach curves based on new crushing scenarios. The laboratory recovery test work data was consolidated and scaled to field conditions to determine projected heap leach performance. Based on the metallurgical testing conducted, the replacement of current tertiary cone crushers with HPGR technology has the potential to increase Coeur Rochester’s silver recovery rate by 8%, from 61% to 69%, and shorten the overall timing of silver recoveries from 20 years to just over two years. INTRODUCTION The Rochester mine, and associated valley fill heap leach facilities is an open-pit silver and gold mine located in Pershing County, Nevada, approximately 26 miles northeast of the city of Lovelock. In 2017, Rochester produced approximately 4.7M troy oz silver (Ag) and 51k troy oz gold (Au). Ore mined at Rochester is either fed directly to the primary X-Pit crusher, crushed at an in-pit crusher system, or placed directly onto a heap leach pad as run-of-mine (ROM). Both crushing circuits are comprised of three stages of crushing to produce a nominal 3/8” ore. Primary crushing consists of jaw crushing while secondary and tertiary crushing are composed of varying cone crushers. Historical recovery rates of crushed Rochester ore average 61.4% Ag and 95.9% Au over a period of 20 years [1]. These rates were derived from third party verification of in-house metallurgical test results, crusher production and heap leach production results from 1986 through 2004 in a private report for Rochester produced by KD Engineering Co., Inc. Recovery rates are regularly verified by compositing daily samples of ore delivered to each leach pad from the X-pit crusher, in-pit crusher, and/or ROM. A proportionate split of each sample is used to generate monthly composites for metallurgical analysis utilizing column leaching and bottle roll leaching. These tests are run in a manner analogous with production conditions and deliver test results that provide expected heap leach performance. As the Rochester oxide deposit has been mineralogically and metallurgically consistent, the gold and silver recovery trends have also been consistent over the life of the project. In 2016 and 2017, onsite and third-party pilot programs were initiated to evaluate the impact of HPGR technology to metallurgical recovery and heap leach performance of crushed product in an open circuit configuration, as a potential replacement for the currently in place tertiary cone crushers. During these years, HPGR was evaluated in three phases of test work.

Jan 1, 2019

By J. M. Mutmansky

Procedures for the determination of the operating point that results when a fan is connected to a mine and placed in operation have been a source of confusion for decades. A variety of techniques has been proposed, often to the detriment of the practicing ventilation engineer trying to apply the techniques to the multitudinous mine/fan matching problems encountered in the engineering of mine ventilation systems. This paper proposes some different assumptions and definitions that simplify the solution of problems in determining the operating point. As a result, a set of procedures is provided for determining the operating point of a mine/fan system when the outlet areas of the mine and fan are known. To establish a major simplification in the development of procedures for the determination of the operating point for a mine/fan combination, the authors suggest that the mine pressures be redefined and then used in such a manner that the conservation of energy is ensured. This provides the basis for the recommendation that the fan operating point be determined using the fan total pressure and the system total pressure characteristics. This procedure can be applied to fans in the blower, booster, and exhaust positions equally well and to both single-fan and multiple-fan networks. Another advantage is that the method is applicable to fans with or without an evase.

Jan 1, 1984

By T. R. West

Planning for urban development in many locations is based largely on 0.10 factors, 1) soil conditions and 2) socio-political aspects of the region. A more widely based approach is necessary, however, if a complete and functional plan is to be obtained. Under this unified approach, the overall field of earth science is included in the planning process. As considered here, the earth sciences comprise a large segment of the natural sciences; that is, geology, pedology, geomorphology, reengineering geology and ground water hydrology. A number of shortcomings can develop when using the restrictive, two-factor approach for urban development planning. These deficiencies are discussed in the paper. The specific considerations for each earth science area are examined and land use considerations for various urban requirements reviewed in light of these specialties. To illustrate the potential of the unified or earth science approach, Tippecanoe County, Indiana is presented as an example. The current area planning system for Tippecanoe County is examined to determine how well it compares with the unified approach and some of the shortcomings of the current plans are discussed.

Jan 1, 1972

By B. Holen, J. R. Baregi, J. A. Organiscak, A. B. Cecala

The National Institute for Occupational Safety and Health (NIOSH) cooperated with 3M Company in the design and testing of a new environmentally controlled primary crusher operator booth at the company’s Wausau granite quarry near Wausau, WI. This quarry had an older crusher booth without a central heating, ventilation and air conditioning (HVAC) system, and without an air filtration and pressurization system. A new replacement operator booth was designed and installed by 3M based on design considerations from past NIOSH research on enclosed cab filtration systems. NIOSH conducted pre-testing of the old booth and post-testing of the new booth to assess the new filtration and pressurization system’s effectiveness in controlling airborne dusts and particulates. The booth’s dust and particulate control effectiveness is described by its protection factor, expressed as a ratio of the outside to inside concentrations measured during testing. Results indicate that the old booth provided negligible airborne respirable dust protection and low particulate protection from the outside environment. The newly installed booth provided average respirable dust protection factors from 2 to 25 over five shifts of dust sampling with occasional worker ingress and egress from the booth, allowing some unfiltered contaminants to enter the enclosure. Shorter-term particle count testing outside and inside the booth under near-steady-state conditions, with no workers entering or exiting the booth, resulted in protection factors from 35 to 127 on 0.3- to 1.0-µm respirable size particulates under various HVAC airflow operating conditions.

Jan 1, 2015

By M. S. Safarzadeh

Cu-As feedstocks are among the most problematic copper sources that have been avoided over the past years. The high arsenic content of such ores/concentrates combined with their refractory nature have directed the metallurgical industry towards developing efficient technologies for the treatment of high-arsenic copper ores/concentrates. As the most important member of Cu-As-S mineral system, enargite (Cu3AsS4) is frequently encountered in some of the important copper deposits. Several hydrometallurgical and pyrometallurgical processes have been examined for the treatment of enargite concentrates, but currently, no commercial operation exists. In an effort to develop an original processing option, an acid bake-leach process has been identified and applied to an enargite concentrate containing ~67% enargite, ~27% pyrite (FeS2), ~3% chalcopyrite (CuFeS2), ~6% sphalerite (ZnS) and <1% galena (PbS). Sulfuric acid baking of this concentrate resulted in the transformation of the concentrate to S8, As2O3, HFe(SO4)2?4H2O, PbSO4 and Cu0.47Fe0.53SO4?H2O, all of which (except elemental sulfur and PbSO4) dissolved during the water leaching step. More than 87% Cu and 64% As were leached when the concentrate was baked at 200°C over 7 h with a sulfuric acid to concentrate weight ratio of 1.6. Less than 1% As was lost to the gas phase. Upon water leaching, copper and arsenic were released to the solution at a concentration ratio of about 3:1. While enargite is very reactive during the sulfuric acid baking reaction, other minerals present in the concentrate such as pyrite, galena, and sphalerite may compete to consume sulfuric acid and be converted into their corresponding sulfates at different levels. The purpose of this paper is to evaluate phase transformations during the acid bake-leach process for the treatment of an enargite concentrate, and to study the effect of sulfuric acid dosage on the extraction of Cu, Fe, and As. In this regard, the concentrate, baked concentrate, and the leach residues are characterized and a conceptual process flowsheet is described for the acid bake-leach process for the treatment of enargite concentrates.

Feb 23, 2014

Lignite is a kind of easy-to-slime and low rank coal. It is hard to be separated by the conventional wet coal beneficiation technologies. Meanwhile, in recent decades, a large amount of fine coal (-6 mm) is generated as the mechanized mining technology has been progressively deployed in coal sector, which causes a great difficult for lignite beneficiation and upgrading due to lack of efficient technology available. In this paper, a vibrated gas-fluidized bed was used to separate the -6 mm fine lignite particles. Separation experiments of -6+3 mm and -3+1 mm lignite were carried out in a laboratory-scale vibrated gas-fluidized bed. The effects of several parameters including the superficial air velocity, vibration intensity, bed height and exterior moisture content on the separation performance were experimentally studied. The results show that the optimal separation performance was achieved when the superficial air velocity is 0.3, the vibration intensity is 1.4, the bed height is 50 mm, the exterior moisture content is below 4% (-6+3 mm) and 2% (-3+1 mm). And the probably error E values of -6+3 mm and -3+1 mm size fraction of lignite are 0.202 and 0.225 respectively. The results indicate that a vibrated gas-fluidized bed can provide an effective solution for -6 mm lignite separation.

Feb 23, 2014

By Y. C. Kim

The strongly skewed grade distributions and the need to estimate the local recoverable reserves in a selective mining environment are the two problems that Ordinary Kriging (OK) cannot easily handle. With the recent introduction of the nonparametric, distribution-free technique of Indicator Kriging (IK), the above problems can be solved. This paper describes the results of performance evaluation of IK in an open-pit gold-silver deposit. For performance evaluation, the predictions of local recoverable reserves using IK were compared with the actual reserves based on blast hole information. The IK estimator, although a bit optimistic, performed very well in predicting the total recoverable ounces of gold from each panel on a test bench. The OK estimator was also used to try to predict local recoverable reserves, by treating each panel as either waste or ore, depending on the panel&apos;s average grade. Under this criterion. OK was found to be very biased and pessimistic.

Jan 1, 1986

By D. C. Lynch

While silica ores are generally considered to have little value, those with exceptionally low B and P content have, potentially, significant worth if processed for use in photovoltaics. The sales value of a cubic meter of ?run of the mill? silica sand is $42 per cubic meter (retail and delivered). If the silica sand can be used to produce solar silicon, its value after processing is $34,000 per cubic meter. Factors that impact the suitability of silica for direct processing in production of photovoltaics are examined.

Jan 1, 2010

By Ali Ekrem Aritan

Exposure to hand-arm vibration (HAV) among the labor force in the mining industry can result in permanent vibration diseases such as behavioral disorders, visual impairment, osteoporosis, pain (mostly in the hands, wrists, and shoulders), circulatory system disorders, and malnutrition. In this study, the vibration exposure of excavator operators working regularly in 25 different natural stone quarries was measured. In addition, the relationship between vibration exposure and rock properties was investigated. Gloved and ungloved vibration measurements were performed and revealed that antivibration gloves reduce excavator operators’ vibration exposure by 7.10–25.95%. Samples from each quarry were characterized with rock mechanics tests. The correlations between the hand-arm vibration measurements and the natural stone physical–mechanical properties (uniaxial compressive strength, Shore hardness, Knoop hardness, apparent density and total porosity) were determined to be over 70%. One finding of the study was that the health risk in excavators cannot be reduced sufficiently by the sole use of antivibration gloves. Furthermore, the excavation of any rock with a Knoop hardness above 121 is associated with an 81% risk of HAV. To increase awareness of the danger of vibration exposure for natural stone miners, training programs should be provided, and technical and operational changes should be implemented.

By S. Veeramasuneni

The interaction of soluble salt particles in their saturated brines is of interest from both a fundamental and practical perspective. The state of dispersion/aggregation of alkali halide particles as determined by optical microscopy can now be described based on non-equilibrium electrokinetic measurements for alkali halides. These results indicate that the sign of the surface charge has a significant effect on the extent of particle dispersion/aggregation. Atomic force microscopy (AFM) is now being used to directly measure the interaction forces responsible for the stability of these alkali halide aggregates observed in optical microscopy studies. These experimental results can be explained based on the interfacial polar interaction theory. In this regard the nature of such particle interaction forces at high ionic strengths are examined to improve our understanding of these systems.

Jan 1, 1997

By M. Vesely

Abrasive grinding, leading to ultrafine product and "critical size" material build-up inside the mill, is proposed as the cause of high power consumption and low capacity in many fully autogenous grinding processes. Addition of steel balls (hence, semiautogenous grinding) or pebble removal and separate crushing have been used, with different efficiencies, to overcome the problem. Information and data for the conceptual analysis, basic design and operation of a pebble crusher at the Los Bronces semiautogenous grinding plant is presented along with data showing a production increase of 1000 mtpd and significant operating costs savings.

Jan 1, 1985

By Emanuele Catelli, Paolo Vicentini, Manuel Petitat, Paolo Lanfranchi

"More than 800 million tons of material will be excavated during large underground projects such as tunnels, undergrounds and power plants by 2030 in Europe only. The raw material excavated is often classified as waste, which involves environmental impact and transport issues: landfill areas, CO2 emissions and noise. But how can such massive amounts of material be transported, processed and deposited? Using the example of the AlpTransit Ceneri Base Tunnel (15.4 km), we show that suitable excavated materials can be used sustainably as a primary resource for tunnel concrete. This requires careful planning of the installations and storage areas by the client, timely building of the processing plants and other handling facilities outside the tunnel and a continuous evaluation of the raw material quality. 1. INTRODUCTION Spoil management is a central element of large construction projects. The systematic reuse of suitable excavated material not only saves natural resources, reduces transport distances and landfill volume, but can also decrease overall construction costs. Ideally, all of the concrete needed for tunnel lining can be produced with this on-site material. Such a natural resource management concept was applied for the construction of the new Gotthard Base Tunnel (L = 57 km). Spoil management concepts are, how-ever, difficult to implement and call for innovative techniques, sophisticated logistics and organization. In the context of large projects, environmentally friendly transport, processing and storage of millions of tons of excavated loose material represent another logistics challenge (Simmen & Lieb, 2010). This paper shows key factors that led to the successful completion of spoil management at the Ceneri Base Tunnel, which constitutes a part of the AlpTransit Gotthard Project (Figure 1)."

Jan 1, 2016

By George H. K. Schenck

The North American-based mining engineer needs to understand the differences that exist between mechanical mining or boring machines built on this continent and those built in Europe. The differences Ere most clearly seen when machines for large-sized openings--about 15 feet high-are considered. This report will focus on the innovations of European origin. The rock-breaking tool, drag bit, or roller cone that is efficient for a particular project is related directly to the strength of the rock involved. This strength is generally stated in reference to the rock&apos;s unconfined compressivee strength in pounds per square inch (psi) although it is well recognized that a rock&apos;s shear strength is also important. Compressive strength has been adopted because it is simple to test for and provides a convenient comparison. Table 1 relates cutter type to compressive strength and indicates the general nature of the machine innovation devel¬oped in Europe.

Jan 1, 1970

By Kenneth R. Krivanek

In recent years the widespread problems of air and water pollution generated by both population and industrial expansion have become a major public concern. Therefore, many municipalities are striving to achieve more efficient wastewater treatment processes so these wastewater&apos;s can be reintroduced into the waterways of our nation with little or no detrimental effects on the future beneficial use of that water. With this, improved treatment comes an ever increasing volume of wastewater sludge which must be disposed of in a manner of minimal impact on the environment. Furthermore, with demand for energy continually accelerating in this nation, our concern over high oil prices and our increasing dependency on foreign oil sources, there has been an ever growing interest in the largest energy source that are nation has, coal. However, surface mining of coal can cause many environmental problems when adequate precautions are not faithfully adhered to. These problems include water pollution from silt and/or clay erosion and acid runoff, produced by oxidation and hydrolysis of pyrite; i.e., FeS2 + 3/02 + H20 + FeSO4 + H2SO4. One method of wastewater sludge disposal which can utilize large volumes of sludge for a beneficial project that may not compound our environmental problems is spray irrigation, to either depleted farmland or to abandoned strip-mined soils. Sludge is characteristically high in organics, as well as having near neutral to alkaline pH properties. With these two qualities it possesses a potential for neutralizing acid strip mine spoils, which would enhance the establishment of a vegetative ground cover. Sludge can accomplish this by lowering the oxidation potential, reducing the solubility of iron and aluminum and by the chelation of metals, thereby

Jan 1, 1977