Search Documents

By J. D. Miller, C. L. Lin

From mine to mill, the 3D characterization of particles ranging in size from meters to micrometers is now possible. A brief review of X-ray tomography for mineral processing is given with recent advances considered, such as high-speed scanning and image analysis procedures to describe important particle properties, including size, shape and composition. Considering these new 3D characterization tools, applications in mineral processing are discussed for high-resolution X-ray microtomography (HRXMT) laboratory analysis of particles ranging from 20 mm to 5 μm, with a voxel resolution of about 1 μm, including (1) multiphase particle characterization by HRXMT and comparison with scanning electron microscopy (SEM), (2) particle damage state as a result of blasting/comminution, (3) liberation characterization to describe expected separation efficiency, (4) exposed grain surface area analysis to explain the flotation of locked particles, and (5) floc size, shape and water content for polymer-induced flocculation. Finally, applications in mineral processing for plant-site analysis using high-speed X-ray computed tomography (HSXCT) are examined, including, for example, coal washability analysis, the analysis of crusher plant products, and the analysis of pebble phosphate products from central Florida. Scanning rates on the order of 1 kg/min for particle sizes ranging from 150 mm to 1 mm are possible, with a voxel resolution of about 100 μm. For coarse particles smaller than 5 to 10 mm, high scanning rates of more than 300 t/h may be possible at a voxel resolution of about 1 mm.

By Erik Westman, Brandon Stables, Benjamin Mirabile

"Standing support is often used in conjunction with underground retreat mining. Knowledge of the load-displacement behavior of standing support and loading induced by the mine opening is critical to proper support selection. The NIOSH STOP database contains load-displacement laboratory test data for most commonly used standing supports. Hydraulic load cells currently used to measure in-situ loading of standing supports have exhibited leakage under load, producing irregularities within the dataset. An improved hydraulic load cell eliminates leakage and produces more consistent data.INTRODUCTIONA hydraulic load cell, more commonly known as a flat jack or JackPack, is a device installed to determine the loading characteristics of the roof-to-floor supports. These standing or roof-to-floor supports include, but are not limited to pumpable cribs, cans, wooden cribs (4-point, 9-point, etc.), metal props, wood timbers, concrete donut cribs, and other variations of these standing supports.Flat jack devices have been used previously to determine the loading of such roof to floor supports. The most commonly used load cell for standing supports is based on a design intended for pre-stressing standing supports, not load measurement. Preloading helps to keep the supports, such as timbers props and cribs, in place during the dynamic loading associated with blasting (Barczak and Tadolini, 2004).Flat Jacks are manufactured in various shapes and sizes depending on the application; common shapes are square and round that are 25.4 mm (1.0 inch) thick when collapsed, as shown in Figure 1. These load cells are produced in South Africa and can be formed into several different shapes depending on the application (Barczak, 2003). The sheet metal that makes up the bladder is comprised of 19-gauge or 1.11 mm (0.04 inch) thickness; the top and bottom pieces of sheet metal are resistance-seam welded around the perimeter. There are two different ports installed on one of the bladder skin corners of the flat jacks; these ports allow fluid to fill the unit, and the other port has a relief valve. The fill port is comprised of a check valve. The pressure relief valve is located in the second port; preset to 1,724 kPa (250 psi), the pressure relief valve keeps the load cell from bursting. Bursting of these load cells typically causes a small tear in the metal skin allowing the fluid to leak out without a large catastrophic failure.The effective inflation range of these load cells is between 25.4 mm (1.0 inch) to 254.0 mm (10.0 inches) thick. Different types of fluids can inflate these load cells but the most common and easily accessible fluid for testing applications is water. Water pressure from the mine supply line can inflate these load cells to the desired load. Depending on the pre-stressing requirements, a pneumatic powered pump, hydraulic pump, or hand pump may be required to inflate the load cells."

Jan 1, 2019

By Karin Bäppler

Mechanized tunnelling is undoubtedly one of the most innovative disciplines in the international construction industry. Technological progress in the planning and production of most modern infrastructure is constantly striving for new records on basis of highly specialized solutions and know-how. Humans and technology have accomplished excellent achievements over the past few years in varied, difficult terrain. New length records are being set with the 64 km long Brenner Base Tunnel and the HS2 Railway system currently under construction in Europe. Cities are building ever longer and more demanding sewer tunnels. The paper highlights some of the challenges, trends and innovations of long-distance tunnelling projects.

Dec 1, 2022

By J. A. Herbst

Fine coal cleaning by froth flotation has become common practice in the U.S. with more than 80,000 tons treated in this way per day. In spite of this large tonnage, developments in the automatic control of coal flotation circuits have lagged significantly behind those for mineral systems. One reason such developments have been limited is that instruments have not been available for the on-line measurement of carbon or ash and another critical variables in coal slurries. A second reason is that the influence of the operating variables on coal flotation has not been completely understood. During the last few years some of the required instrumentation has been developed and an improved knowledge of the flotation process itself has occurred through mathematical modeling; as a result certain control strategies for coal flotation are beginning to emerge. This paper attempts to evaluate several control strategies using a detailed flotation dynamic simulator, DYNAFLOAT. After constructing a process matrix for the system of interest, promising alternatives for linking manipulated and controlled variables have been analyzed. In order to develop combined grade and recovery control strategies, the authors found it necessary to construct a grade/recovery map with the aid of the simulator to drive the system to known final, feasible grade/recovery operating conditions. Finally, an advanced strategy which uses an on-line model to identify disturbances and take control actions is proposed.

Jan 1, 1983

By William Hodder, Ehsan Alavi, Nader Ghasempour, Daniel Cressman

The Don River & Central Waterfront Coxwell Sanitary Bypass Tunnel (CBT) Project in Toronto will extend approximately 10.5 km from Ashbridges Bay Treatment Plant west under Lake Shore Boulevard, north under Bayview Avenue and east through the Don River park area to the Coxwell Ravine Park. The tunnel is currently being mined by using a shielded dual-mode tunnel boring machine (open and close) capable of operating in EPB mode and lined by using a precast concrete segmental tunnel linear with an internal diameter of 6,300 mm and external diameter of 6,900 mm. The CBT is expected to be excavated mainly through shale bedrock of the Georgian Bay Formation, at approximately 50 meters deep. The tunnel crosses a buried bedrock valley in two locations, in the southern portion of the alignment, adjacent to the Don River, and at the northern portion of the alignment approaching the CX-1 shaft. In these two locations, the bedrock cover is expected to be less than 6 meters. The risk of encountering weathered bedrock, significant ground water inflows or surficial soil deposits through these buried valleys was identified during the design phase. The contract required the TBM to be designed with the ability to probe drill ahead of the TBM and convert to EPB mode if necessary, to cross this area. This paper will discuss the additional exploration that was performed by the contractor to identify the extent of this buried valley, the plan going into the zone of potential weathered shale, and the actual conditions encountered.

Jun 13, 2021

By R. A. Jankowski, J. D. Potts

Four underground respirable dust surveys were conducted to determine factors affecting belt entry dust levels and how using belt air to ventilate work areas affected dust exposures. Belt entry dust levels on the surveyed longwall and continuous miner section averaged 0.59 and 0.26 mg/m3, respectively. The stageloader/crusher contributed an additional 0.5 to 0.9 mg/m3 of dust to belt air, while the feederbreaker contributed 0 to 0.2 mg/m3 of dust. A 1000 ft (305 m) increase in belt entry length or a 200 to 500 tons/shift (181,000 to 454,000 kg/shift) increase in production resulted in roughly a 0.1 mg/m3 increase in dust. Using the belt entry as an intake entry on the continuous miner section appeared to reduce dust levels by 0.1 to 0.3 mg/m3 during cutting. Belt air was not used to ventilate the face on the longwall section.

Jan 1, 1992

By Chengliang Jliang, B. K. Parek, Xuxin Shao

Of the impurities present in phosphate ore, dolomite is the most difficult to remove due to the similar chemical compositions of the impurities and also adsorption of dissolved species of dolomite onto phosphate. A new amphoteric surfactant was found to be a suitable collector for separation of dolomite from phosphate. Flotation results showed that the new amphoteric collector had a high flotation selectivity for dolomite in wide pH ranges. The flotation study of francolite and dolomite in each other's supernatant demonstrated that the dissolved ions had little effect on the selectivity of the new collector, but were detrimental to the flotation separation using sodium oleate as collector. A phosphate concentrate with 35.2% P2O5 with 90% recovery was obtained using 290 g/t of the amphoteric collector from a mixture of francolite and dolomite containing 26.2% P2O5. The rejection of MgO was 81.41%.

Jan 1, 1999

By K. A. Stanley, N. A. Karl, D. R. Wilburn

"This summary of international mineral exploration activities for the year 2014 draws upon information from industry sources, published literature and specialists in the U.S. Geological Survey (USGS) National Minerals Information Center. The summary provides data on exploration budgets by region and mineral commodity, identifies significant mineral discoveries and areas of mineral exploration, discusses government programs affecting the mineral exploration industry and presents analyses of exploration activities performed by the mineral industry.Three types of information are reported and analyzed in this annual review of international exploration: 1) budgetary statistics expressed in U.S. current dollars provided by SNL Metals & Mining (SNL) of Charlottesville, VA; 2) regional and site-specific exploration activities that took place in 2014 as compiled by the USGS and 3) regional events that affected exploration activities including economic, social and political conditions, which were derived from published sources and discussions with USGS and industry specialists. Commodity and regional compilations are presented in this summary. Because multiple sources are used to develop these compilations, statistics may differ depending on the source and type of data that are being reported.The SNL data summarize planned company budgets for worldwide exploration activities in 2014 for 19 nonfuel mineral commodities based on company surveys. Research focused on precious metals (gold, platinum-group metals and silver), base metals (cobalt, copper, lead, molybdenum, nickel, tin and zinc), bulk commodities (iron ore, phosphate and potash), and specialty mineral commodities (diamond, lithium, niobium, rare-earth elements, tantalum and uranium). Information on uranium exploration activities was included for the first time in 2007. Data on lithium, niobium, phosphate, potash, rare-earth elements and tantalum were compiled for the first time in 2010 because of their increased significance. Since 1999, companies with exploration budgets of $100,000 and greater were included in the SNL compilations. SNL budget estimates exclude bauxite, coal and oil and gas. Exploration budget estimates for iron ore have been compiled since 2011 but reported separately. The 2014 SNL company survey is reported by SNL to cover an estimated 95 percent of the world’s nonferrous, nonfuel mineral exploration budgets. The 5 percent that is not covered includes companies that chose not to participate in the SNL survey, private companies that do not publish their budget data, and government-funded exploration activities"

Jan 1, 2014

By J. D. Miller, J. Hupka

Important aspects of kerosene penetration into tar sand have been investigated. The natural tar sand porosity was measured and used to analyze the performance of the hot water process. Subsequently, pretreatment experiments, using 20-kg tar sand samples (Asphalt Ridge and Whiterocks, Utah) and kerosene as a diluent were carried out at the expected summer temperature (26°C) and the expected winter temperature (-14°C). The natural tar sand porosity accessible by diluent has a crucial impact on the reduction of bitumen viscosity and influences the penetration time required for successful bitumen separation from tar sand by hot water processing. Thus, the tar sand porosity is a critical variable that determines appropriate operating conditions. Experimental results indicate that diluent penetration into the Asphalt Ridge tar sand (high porosity) is almost complete after 30 min, whereas for the Whiterocks tar sand (low porosity) the penetration process is much slower, being still incomplete after 15 hours regardless of the ambient temperature.

Jan 1, 1994

By P. Karimi, A. Akcil, A. Amini, H. Abdollahi

"In this study, cyanidation experiments were carried out on a massive sulfide ore sample, whose grades of the precious metals gold and silver were found to be 4.2 g/t and 311.9 g/t, respectively. Other elements in the ore were arsenic with average grade of 1,751.6 g/t; antimony, 619.7 g/t; zinc, 781.4 g/t; copper, 454.6 g/t; lead, 101.8 g/t; mercury, 324.3 g/t; and bismuth, 0.6 g/t. The first objective of test work focused on determining the best conditions for extracting gold from the ore, ground to less than 75 microns. Different influential parameters such as particle size fraction, cyanide concentration, pH and leaching time were investigated. The optimum parameters were found to be particle size fraction of less than 25 microns, cyanide concentration of 2,000 mg/L, pH of 11 and cyanidation time of 24 hours. In these optimum conditions, the highest gold and silver leaching efficiencies were 76.88 and 59.63 percent, respectively. In addition, roasting as pretreatment at a temperature of 700°C over a period of two hours was evaluated. Cyanidation testing of the roasted ore in the optimum conditions found increases in the gold and silver leaching efficiencies to 85.97 and 67.57 percent, respectively. Moreover, antimony extraction rose to 43.10 percent, from 23.73 percent without roasting.IntroductionGenerally, gold ores can be classified as “free milling” or “refractory,” depending on how they respond to cyanide leaching (La Brooy et al., 1994; Celep et al., 2009). While high gold recoveries (> 90 percent) from free-milling gold ores can be readily achieved, refractory gold ores are often characterized by low gold recoveries (50-80 percent) within a conventional cyanide leaching process (Rubisov et al., 1996; Adams, 2005; Celep et al., 2009). The presence of preg-robber components such as carbonaceous matter, sulfide minerals and aluminosilicate can further decrease gold and silver dissolution rates and recoveries. With the negative effect of the presence of preg-robbers, gold dissolution is considerably diminished in solutions with high cyanide concentration (Tan et al., 2005). In such refractory gold ores, gold particles may sometimes be occluded or included in the sulfide minerals, and pretreatment becomes necessary to break down the mineral structure to liberate gold for subsequent recovery. These ores are usually pretreated with an oxidizing process, after which gold and silver can be recovered by a standard cyanidation process. The main oxidizing processes available for refractory gold ores are roasting (LaBrooy et al., 1994; Angelidis and Kydros, 1995; Li et al., 2009; Karimi et al., 2010; Kyle et al., 2012), biological oxidation (Lawrence and Bruynesteyn, 1983; Komnitsas and Pooley, 1990, 1991; Deng and Liao, 2002; Ciftci and Akcil, 2010, 2013) and pressure oxidation (Mason, 1990; Murthy et al., 1992; Qingcui et al., 2009). In addition, ultra-fine grinding is being used in some plants for the liberation of gold and silver particles that are interlocked in the sulfide or silicate minerals (Celep et al., 2011)"

Jan 1, 2015

By Miguel Angel Banuet Rodriquez, Hector Conceso Aragon

"Construction of the longest road tunnel in Mexico is part of Acapulco’s alternate roadway to the scenic roadway project. This article provides a brief summary regarding details of the construction since the project began. Work was done by skilled engineers and Mexican workers that includes outstanding execution of the work in an urban and tourist area. This project will have a strong impact on the steady development of the port of Acapulco.Project locationAcapulco’s Alternate Roadway Project is currently under construction in the city of Acapulco, located in the Guerrero state of Mexico. It is an 8-km (5-mile) long roadway that starts at the Icacos neighborhood, heading toward Acapulco’s airport, crossing a drill-and-blast tunnel that is 3,160 m (10,350 ft) long under Veladero Park, a mountainous area. The tunnel overburden reaches a depth of 380 m (1,250 ft) approximately at the central point of the horizontal alignment, and continues with a 4-km (2.5-mile) long elevated road to connect to the existing Viaducto Diamante toll road (Fig. 1).Tunnel construction has already been finished using two portals for drilling and blasting operations; Brisamar Portal on the west side and Cayaco Portal on the east side (Fig. 2).Geometric dataOnly two main excavation cross-sections were considered in the executive design. The first one corresponds to the running tunnel for a three-lane vehicle section, with crosssection areas between 120 and 130 m2 (1,290 and 1,400 sq ft) taking into consideration different geological and geotechnical conditions to be encountered (Fig. 3).The second one corresponds to eight emergency bays, each one 50 m (164 ft) long, laid down within the tunnel outline, located at 400 m (1,312 ft) from each one with excavation cross-sections between 156 to 169 m2 (1,680 to 1,820 sq ft), in accordance to geological and geotechnical conditions to be encountered (Fig. 4).The tunnel’s horizontal alignment is completely straight, having a small curve within the vertical alignment on Cayaco portal, because there were some differences in levels when tunnel excavation started. Tunnel slopes were designed in such a way that rainwater does not run down into the tunnel at any time."

Jan 3, 2018

By Joel K. Waterland

GENERAL DESCRIPTION Homestake Mining Co.'s operations are at Lead, SD. Production from the various methods used are: 1 155 753 t/a (1,274,000 stpy) by open cut-and-fill, 68 039 t/a (75,000 stpy) by square set cut-and-fill, 144242 t/a (159,000 stpy) by shrinkage stoping, 107 048 t/ a (118,000 stpy) by blasthole stoping, and 67 132 t/a (74,000 stpy) in development work for a total of 1 542 214 t/a (1,700,000 stpy). Mining takes place from the 616-m (2000-ft) level to the 2073-m (6800 ft) level (Fig. 1). The average travel time to the stope is 45 min. GENERAL ORE BODY REQUIREMENTS AND LIMITATIONS Size, Shape, and Dip of Ore Body Six major ledges varying from 914 m (3000 ft) long by 228.6 m (750 ft) wide to 305 m (1000 ft) long by 122 m (400 ft) wide are mined. Within these ledges are irregular-shaped areas of varying sizes. These ledges dip at approximately 1.2 rad (70°) to the east and plunge to the south from 0.26 to 1.57 rad (15° to 90°). Ground Conditions The ore is cummingtonite (chlorite schist) which is very competent except for major bedding planes and fracture patterns. The footwall is a slate but because of the dip presents very few problems. The hanging wall is also a slate which because of the dip and bedding is very weak and requires considerable rockbolting. No problem has been encountered with rock bursts to a depth of 2438 m (8000 ft). Ore Value The ore values vary somewhat from ledge to ledge, but the average ore delivered to the mill is approxi¬mately 6.2 g (0.2 oz) of gold per ton. A small amount of silver is the only byproduct of this operation. Annual production of gold is approximately 10 575 183 g (340,000 troy oz). Production Requirements The mine has a mill capacity of approximately 1 723 651 t (1,900,000 st) but because of several fac¬tors (manpower, depth, etc.) this mill capacity has not been attainable for the past several years.

Jan 1, 1982

By William H. Eatock

The Saskatchewan ore zone strikes slightly south of East, from the Alberta border to Manitoba; and dips to the South. The conventional mines are located along a broad strike line from Saskatoon to Esterhazy-Rocanville. Nine conventional mines have developed ore bodies at a nominal depth of 915 metres (3000 ft.). One mine had developed an ore body at 1525 metres (5000 ft.) by solution mining. Mining reserves of 100 years are not unusual in this vast ore body. Most of the mines were brought on stream during the 1960s. All the conventional mines were influenced by practices developed at Carlsbad, N.M. By 1970, the industry was faced with serious over-capacity resulting in the cancellation of some projects and the introduction, by the provincial government, of the Potash Pro-rationing Regulations designed to share the available market amongst all the producers. This resulted in production rates as low as 40% of capacity. As a result, the 1970s were characterized by attempts to reduce cost, rather than improve production or processing techniques. In recent years, the plants have all been brought to full capacity, and are currently involved in a massive program of expansion, which promises a period of advancing technology.

Jan 1, 1980

By Bjorn Olsson

"Heavy impact. High frequency hammering. Extreme abrasion. Building on the experience of owning and operating its own mines, Ovako has developed a deep knowledge of how vital the right steel properties are in withstanding the extreme loads encountered in every part of the drill string. That is why Ovako’s product development process is focused on understanding the specific load cases and manufacturing operations associated with rock tools.The punishing conditions of percussive drilling can push the limits of most materials. And heavy mechanical loads are only the beginning. Highimpact energies at high frequency are a major source of fatigue. High temperatures result from impact energy losses. And abrasive, erosive and adhesive wear are constant risks. Handling any of these varying demands at a single point along the drill string is difficult enough — which makes optimizing for the entire drilling system an extremely complex challenge. Engineering for specific loadsOvako has specialized over many decades in analyzing the dominant loads for each of the parts and components used in rock tools, and testing for individual applications in its laboratories. The most critical fatigue properties are controlled through the steel metallurgy, and supported by performance measurements through extensive rotating bending fatigue (RBF) testing, along with special methods that combine impact load with various wear loads. The result is a fit-for-purpose steel with tightly controlled performance properties, making it possible for customers to precalculate the expected life time of their components for highly automated and repetitive processes Tailoring steels for the processing route.The same levels of control and predictability must be carried through to the customer’s own manufacturing processes. By ensuring minimal variations in chemical composition, everything from heat treatment and welding to automated machining can be carried out with high consistency. With precisely controlled material properties based on an existing processing route and exact load case, customers are able to minimize their total tool production costs while ensuring optimal performance for their end products. Development of Hybrid SteelBuilding on this experience in the mining industry, Ovako has developed a new steel family, known as Hybrid Steel, designed to meet the demands of high-stress, elevatedtemperature applications where mechanical and fatigue strength are critical. Traditionally, steels for these applications are produced by expensive small-batch processes. Hybrid Steel, however, enables high volume production at a competitive cost.The world of steel has traditionally been divided into clearly separated categories of tool steel, stainless steel and lower alloy engineering steel. Hybrid Steel is now challenging that division, offering attractive properties from all three categories."

Jan 12, 2017

By Mary E. Learmont

Grinding with steel media adversely affects the flotation response of galena. Electrochemical measurements, flotation tests, and AES, XPS, and STEM examinations were employed to identify interactions between galena and mild steel. Iron oxide, hydroxide, or sulfate species that formed on the galena surface upon contact with mild steel decreased its floatability, with the time of contact and aeration condition affecting the severity of the flotation depression.. Parallel tests performed with an active metal, magnesium, indicated that floatability was also affected by the presence of a surface coating involving lead species.

Jan 1, 1984

By D. R. Wilburn

This summary of international mineral exploration activities for the year 2013 draws upon information from industry sources, published literature and U.S. Geological Survey (USGS) specialists. The summary provides data on exploration budgets by region and mineral commodity, identifies significant mineral discoveries and areas of mineral exploration, discusses government programs affecting the mineral exploration industry and presents analyses of exploration activities performed by the mineral industry. Three sources of information are reported and analyzed in this annual review of international exploration for the year 2013: 1) budgetary statistics expressed in U.S. nominal dollars provided by SNL Metals & Mining (SNL) of Halifax, NS, Canada (formerly Metals Economics Group (MEG); 2) regional and site-specific exploration activities that took place in 2013 as compiled by the USGS; and 3) regional events that affected exploration activities, including economic, social and political conditions, that were derived from published sources and unpublished discussions with USGS and industry specialists. Commodity and regional compilations are presented in this summary. Because multiple sources are used to develop commodity and regional compilations, reported statistics may vary depending on the source and type of data that are being reported. The SNL data summarize planned company budgets for worldwide exploration activities in 2013 for 20 nonfuel mineral commodities based on surveys returned by companies primarily focused on precious metals (gold, platinum-group metals and silver), base metals (cobalt, copper, lead, molybdenum, nickel, tin and zinc), bulk commodities (coal, iron ore, phosphate and potash), and specialty commodities (diamond, lithium, niobium, rare-earth elements, tantalum and uranium). Information on uranium exploration activities was included in the MEG overview for the first time in 2007. MEG included data on the commodities lithium, niobium, phosphate, potash, rare-earth elements and tantalum for the first time in 2010 because of the increased topical significance of these commodities. Since 1999, companies with exploration budgets of $100,000 and greater were included in the MEG and SNL compilations. SNL budget estimates exclude aluminum, coal, and oil and gas. Budget estimates for iron ore have been compiled since 2011 but reported separately. The post-1999 budget surveys by MEG and SNL cover at least 90 percent of world?s reported nonferrous, nonfuel mineral exploration budgets; the 2013 survey is reported by SNL to cover an estimated 95 percent of these budgets. The 5 percent that is not covered is accounted for by companies that chose not to participate in the SNL survey, private companies that do not publish their budget data, and government-funded exploration activities.

By Rajat Gangrade, Haotian Zheng, Jarrett Smith, Daniele Nebbia, Mike Mooney

The application of artificial intelligence (AI) to improve tunnel boring machine (TBM) operations requires a significant amount of information to train robust performance prediction models, e.g., for tunneling-induced settlement, productivity, tool wear, etc. This paper presents the AI framework applied to the North-East Boundary Tunnel (NEBT), the largest component of the Clean Rivers Project in Washington, DC. The paper focuses on required elements for real-time AI use to estimate tunneling-induced ground and building deformation and cutter tool wear. Keys to the framework include defining the necessary quantities of data required as well as the process of windowed training, validation and model testing. To date, the models developed for ground deformation and tool wear show satisfactory performance when compared to observed field observations during tunneling.

Jun 13, 2021

By A. Aly Selirn

An economic simulation model was developed to predict the amount of copper recovered from copper oxide deposits and the cost of producing it as a function of the deposit parameters. The economic simulation model includes models of fragmentation design and cost, copper extraction, solution distribution and recovery, effluent solution cutoff grade, and financial analysis. Cost and price indices were also developed to evaluate the economic feasibility of in situ leaching operations as a function of their starting date. Application of the models to various properties having the same area and different ore thickness shows that the effluent solution cutoff grade does not vary with the ore thickness nor with its grade. The percent of copper recovery is, however, shown to increase with the increase in the ore thickness and is independent of the ore grade. it is also shown that while the profit per unit of extracted copper increases with the increase in ore grade or ore thickness, the rate of return on total investment does not show any correlation

Jan 1, 1977

By Dieter Loh, Mathias Knoll, Florian Werres

When a new tunnelling project starts, it has been a vital tradition for decades to cast and erect master rings horizontally on a flat surface to demonstrate the compliance with dimensional tolerances. Some tenders ask for the erection of two or even three rings upon each other or repeated master ring erections at intervals throughout the project. Especially for large diameters, this is a challenging and risky task for the workforce in the segment factory. A truck-mounted crane is often necessary, and in some cases it can take up to a week to complete a master ring. The concept of virtual rings has the potential to replace this tradition by assembling master rings digitally instead of physically. This is based on a best-fit approach, considering the 3D coordinates from laser tracker measurements of segments or segment moulds. Building a virtual ring, a sub-millimeter accuracy can be achieved, the alignment of neighboring circumferential and ring joints observed, and the fit of bolt holes checked. The traditional method, on the other hand, is discussed controversially despite the significant amount of work and risks—particularly as the horizontal position of the ring and absence of gaskets do not simulate the reality in the excavated tunnel. This paper will highlight the technical aspects of virtual rings, as well as their pros and cons, illustrated by a case study from London Thames Tideway where a total of 30 physical master rings could be replaced by virtual rings.

Jun 13, 2023

By Patricia Pride, Mike Robison, Jon Bergenthal, Wojciech Klecan

"The Lower and Middle River Des Peres (LMRDP) CSO Storage Tunnel is the largest single component of Metropolitan St. Louis Sewer District’s (MSD) CSO control system improvements planned to meet consent decree requirements for MSD’s Lemay Service Area. The 13.7-km (8.5-mile) long, deep, hard rock tunnel will have a finished diameter of 9.1 m (30 ft). Beginning at the Lemay Wastewater Treatment Plant (WWTP), the alignment follows the channelized River Des Peres to the outfall of the existing Forest Park tubes, as indicated in Fig. 1.The project includes three construction shafts, 34 intakes and a deep, cavern-style pump station located adjacent to the WWTP. The tunnel will be driven from the Defense Mapping shaft to the Macklind shaft. Another shaft is located near the midpoint at the tunnel in River Des Peres Park.The Forest Park intake, located at the upstream end of the tunnel just beyond the Macklind shaft, is a large, tangential vortex intake structure. With a peak flow rate of 170 m3/s (6,000 cfs), it will have a 6.1-m (20-ft) diameter dropshaft to transfer flow into the tunnel.The project includes another three large tangential vortex-flow intake structures with peak flow rates ranging from 28 to 44.5 m3/s (990 to 1,570 cfs). These large intakes are located at points where three large sewers (formerly creeks) enter the River Des Peres. Dropshaft diameters for these intakes range from 3 to 3.7 m (10 to 12 ft) in diameter. The 30 remaining intakes are smaller tangential vortex-style, with dropshafts in the range of 0.8 to 1.7 m (30 to 66 in.) in diameter.Each intake structure drops flow into a deaeration chamber constructed adjacent to the tunnel at tunnel depth. Intake tunnels transfer flow from the deaeration chambers to the main tunnel. Most of the intake tunnels are short. However, two are long. The Glaise Creek tunnel will extend 762 m (2,500 ft) from the main tunnel to the Alaska Park intake, while the Rock Creek tunnel will extend 823 m (2,700 ft) from the main tunnel to the Rock Creek intake. The dewatering pump station, located at the downstream end of the tunnel, will be built inside a large, horseshoe-shaped cavern with two access shafts. Excavation of the cavern and its access shafts will be performed by the tunnel contractor. Build-out of the dewatering pump station will be performed under separate contract."

Jun 1, 2019