Search Documents

By Amir Karami, Scott Munro

This paper focuses on remediation of a 3.6 km long water conveyance tunnel that suffered two large falls of ground (FoGs), one of which subsequently progressed to the ground surface, resulting in full collapse of the tunnel. The tunnel is part of a network of water conveyance tunnels and open channels that direct water into two turbines located in an underground powerhouse, originally constructed in the 1970s. At the time of construction, the tunnel was partially supported with shotcrete or rock bolts, with no further ground support added since construction. Two sonar surveys in 019 and 01 identied two adacent large FoGs in the tunnel, approimately 1.2 km from the tunnel outlet. Historical geological and geotechnical information indicated that the FoGs occurred within a 60 m wide fault zone. Remediation plans were developed, which included stabilization of the outlet channel, the portal, the tunnel leading up to the FoG areas (1.2 km length) and the FoG areas. Several remediation options were considered to restore the tunnel, including construction of a diversion tunnel to bypass the FoGs or remediation of the FoG areas with steel ribs and backlling the void above the FoGs to surface.

Jun 23, 2024

By D. J. Pandelis, W. J. Schlittler

Auxiliary Equipment pumping systems to support primary, secondary and regrind grinding circuits will be the primary focus of this paper. Every grinding system is unique and requires special design considerations for proper application of pumps to transport mill discharge. To satisfy the majority of applications, a new series of pumps has been developed by Svedala, known as World Class Pumps. Selection of these newly developed pumps for each type of grinding circuit will be presented. Specific components of selection are materials of construction, piping system, classification method, material characteristics and slurry characteristics. Both horizontal and vertical pump applications will be reviewed with emphasis on rules of pump piping and sump design.

Jan 1, 1999

By Graham G. W. Mustoe, Andrew I. Hustrulid

An advanced numerical model based upon the Discrete Element Method (DEM) has been developed to provide the engineer with unique detailed information to assist in the design of transfer points in large industrial conveyor systems in mining operations. This modeling technique provides a quantitative description of the bulk solids movement through the transfer point. This information consists of the velocity distribution of the bulk solids and the stresses within the bulk solids. The DEM model also gives detailed information concerning the impact forces acting on the transfer structure and the conveyor belts from the bulk solids flow.

Jan 1, 1996

By Mehmet Guney

Acceptable working environments in production areas and service openings of Mindola Mine on the Zambian Copperbelt are currently maintained with an air volume of 1000 cu m/s and 5500 kW of installed refrigeration plant. It is planned to open up additional deeper areas of the mine for future production. Temperature problems, due to the increased heat generation from various underground sources are recognized as potential hinderances to efficient production. Findings of research work indicate that the present total heat output of 58,000 kW will inevitably increase by the second five-year period of the deepening program to 52,900 kW and by the fifth five-year period to 63,200 k\V. Estimated WB and DB temperatures, representing the total heat generation in stope faces and development headings during these same periods are predicted to increase to 53.8/40.2 °C and 35.5/42.1 °C respectively. It is assessed that the nominal refrigeration capacity needs to be progressively increased to 9,000 k\V This paper deals with the thermal problems in Mindola Mine, current heat output calculations, future prediction of temperature and heat load in various working areas of the mine with the application of computer programs and interpretation of data in order to find the effective solution for long-term planning of ventilation and air-conditioning.

Jan 1, 1982

By A. Bhattacherjee

Industries in general and the mining industry in particular have become more safe than ever before. However, there is a need to increase the search for the causes of mining work-related injuries and to contribute to their reduction through job design, work procedures, and worker training. Mine accident and hazard control has to be practiced in a manner which is consistent with the overall objectives of the mine management, among which are the optimum allocation and effective utilization of the resources. The purposes of this paper are to (i) review the role risk analysis in safety management with references from mining and other industries; (ii) discuss the risk measures appropriate for injury analysis; (iii) present a set of analytical tools to injury experience data in under-ground coal mines; (i v) apply these tools on case study example; (v) discuss the results of the case study; and (vi) amplify the application limitations and the future research needs.

Jan 1, 1991

By George O. Lower

The use of cyanides in the extraction of gold and silver is well known.1 Such extractions employ con¬centrations of cyanide in the range of 0.02-0.25 % sodium cyanide equivalent in leaching cycles of 24-48 hours and frequently longer. Copper minerals, even though minor components of precious metal ores, dissolve in these cyanide leaching solutions, consume cyanide, cause fouling of mill solutions, and thus interfere with the precipitation and recovery of gold and silver. 2,3,4 This paper presents a summary of laboratory investigations on the use of cyanide solutions as extractants for copper from various copper-bearing ore fractions. In view of the metal contents involved, it will be apparent that larger quantities of cyanide are required to extract copper than for the extraction of precious metals. In cyanide solutions of concentrations generally favorable to copper extraction, sulfide and oxide copper minerals were found to dissolve rapidly at room temperature and atmospheric pressure. For example, on products in the flotation size range, the major portions (e.g. 65-85%) of the extractable copper frequently dissolved in 2-10 minutes. At coarser grinds, e.g. 100% minus 28 mesh and 100% minus 10 mesh, 75-85% of the total copper was extracted in 30 minutes.

Jan 1, 1966

By A. Vien

A major thrust in Industrial automation over the past few years has been the exploration and incorporation of higher level (supervisory and optimizing) control strategies aimed at more fully exploiting the existing control system infrastructure. There is little doubt that this is worthwhile pursuit, however, one must not lose sight of the maintenance and development requirements of the basic control system. Statistics on loop performance indicate that this too is an area of considerable potential. In this paper the authors look at some of the less elegant, but arguably equally important issues in mineral processing plant control. The focus is on controller structures, loop tuning, sampling, filtering, and some of the other principal components of the regulatory control foundations. In many cases significant improvements In control performance can be achieved by getting back to the basics.

Jan 1, 1998

By N. A. Karl, D. R. Wilburn

"This summary of international mineral exploration activities during 2017 draws upon information from industry sources, published literature, SNL Metals & Mining (SNL), an offering of S&P Global Market Intelligence (New York, NY) and specialists in the U.S. Geological Survey (USGS) National Minerals Information Center. Three types of information are reported and analyzed in this annual review of international exploration: 1) budgetary statistics expressed in U.S. dollars provided by SNL; 2) regional and site-specific exploration activities that took place in 2017 as compiled by the USGS and 3) regional events and legislation that affected exploration activities including economic, social and political conditions, which were derived from published sources and discussions with USGS and industry specialists. Commodity and regional compilations are presented in this summary. Because multiple sources were used to develop commodity and regional compilations, statistics may vary depending on the source and type of data that are being reported.The SNL data summarize budget estimates for worldwide exploration activities in 2017 for 30 nonfuel mineral commodities and metal alloys, based on company surveys. Surveys focused on precious metals (gold, platinumgroup metals (PGMs) and silver), base metals (cobalt, copper, lead, molybdenum, nickel, tin and zinc), bulk commodities (bauxite, chromite, iron ore, manganese, phosphate and potash), and other commodities (aluminum, antimony, diamond, graphite, heavy-mineral sands, lithium, niobium, rare-earth elements (REEs), scandium, tantalum, tungsten, uranium, vanadium and yttrium). Information on uranium exploration activities was included in SNL’s survey for the first time in 2007. Data on lithium, niobium, phosphate, potash, REE and tungsten were compiled for the first time in 2010, and scandium, vanadium and yttrium were added in 2014 because of their increased topical significance. Since 1999, companies with exploration budgets of $100,000 and greater were included in the SNL surveys. SNL budget estimates exclude coal, and oil and gas. The 2017 SNL mining company survey compilation was reported by SNL to include an estimated 95 percent of the world’s nonfuel mineral exploration budgets. The 5 percent that was not covered was accounted for by companies that chose not to participate in the SNL survey, private companies that do not publish their budget data, and government-funded exploration activities."

Jan 5, 2018

By R. Todd Swinderman

"Higher production demands across all bulk handling segments require increased efficiency at the lowest cost of operation, in the safest and most effective manner possible. As conveyor systems become wider, faster and longer, more energy output and more controlled throughput will be needed. Add an increasingly stringent regulatory environment and cost-conscious plant managers must closely review which new equipment and design options align with their long-term goals for the best return on investment (ROI).There are primarily two separate market segments using conveyor belts. One is in process industries such as food, chemicals, paper and powders. Handled in relatively low volumes, the bulk materials that enter these processes are generally of a consistent size and quality. The other market includes mining, coal handling and cement, where the bulk material’s quality and size vary, and the volumes are typically much greater. While both segments face similar issues with safety and environmental control, the properties of the materials handled and the volumes transferred suggest different approaches, with one thing in common: increased belt speeds requiring modern equipment upgrades.Safety at higher belt speedsWith companies recognizing that safety does indeed pay, safety is likely to become a new source of cost reduction. The percentage of mines and processing facilities with a robust safety culture are likely to increase over the next 30 years to the point where it is the norm, not the exception. In most cases, with only a marginal adjustment to the belt speed, operators quickly discover unanticipated problems in existing equipment and workplace safety. These problems are commonly indicated by the larger volume of spillage, increased dust emissions, belt misalignment and more frequent equipment wear or failures."

Jan 7, 2017

By J. B. Hedrick

Rare earths were not mined in the United States in 2008. However, processing of intermediate rare-earth concentrates continued throughout the year at the Mountain Pass Mine in California. Consumption of refined rare-earth products increased. U.S. rare earth imports were primarily from China, with lesser amounts, in decreasing order, from France, Hong Kong, Japan, Austria and Russia. The United States imported 100 percent of its supply of yttrium metal and compounds primarily from China. United States In 2008, lanthanide concentrates were processed by Chevron Mining Inc. (previously Molycorp Inc.) at its mine site at Mountain Pass, CA. Chevron Mining sold its entire holdings in the rare earths mine to Molycorp Minerals LLC in September and operations continued at the site through-out 2008. Major uses for these mineral commodities were in automotive catalytic converters, petroleum fl uid-cracking catalysts, permanent magnets, glass-polishing compounds, ceramics, metal-alloying additives, phosphors and recharge-able batteries. Three domestic companies produced and sold lanthanide intermediate concentrates and refined products. Chevron Mining sold its interests in the Mountain Pass Mine to Molycorp Minerals LLC on Sept. 30, 2008. Molycorp Minerals LLC is an investment company owned by Resource Capital Fund IV L.P., Pegasus Partners IV, LP, The Goldman Sachs Group Inc., Traxys North America LLC, Carint Group LLC and Mark Smith. The Molycorp operation previously mined the rare earth fluocarbonate mineral bastnäsite by hard-rock surface methods, and the mine remained on care and maintenance in 2008. Molycorp maintained significant stocks of bastnäsite concentrates, intermediate concentrates and high-purity rare earth compounds at its operations at Mountain Pass. In October 2007, Chevron Minerals completed phase one of its three-stage plan and restarted the rare earth separation plant at Mountain Pass. The company also processed intermediate rare earth concentrates from existing stocks during the first three quarters of 2008. Molycorp Minerals LLC maintained production in the last quarter of the year. The mine at Mountain Pass has been closed since 1998. Future plans are to restart processing of stockpiled bastnäsite concentrates followed by reopening of the mine.

Jan 1, 2009

By K. D. Dill, S. D. Rosenthal

"This project analyzed the efficiency of incorporating the use of directional drilling technology into coal overburden blasting. Directional drilling is currently in use in the petroleum industry and it is believed that it will be a valuable asset in the mining industry. This project has shown that directional drilling can be a viable technology for use in the coal overburden removal process resulting in increased drill utilization and potential for cost savings. Future work regarding blasting and geotechnical evaluation should be performed to solidify the concept. INTRODUCTION Determine the Potential Drill Utilization Improvements and Rock Fragmentation Requirements Using Directional Drilling in a Coal Mining Overburden Highwall Application was a project funded by Atlas Copco Drilling Solutions (Atlas Copco) based in Garland, Texas. The project was developed and researched by Montana Tech of the University of Montana. This project was intended to show how the use of directional drilling can increase drill utilization, while decreasing costs, without sacrificing overburden blasting results. This paper discusses a review of the literature, the methods performed, conclusions and future work Background Atlas Copco theorized that an alternative approach to drilling a cast blast pattern would be beneficial to coal mining operations by increasing drill utilization and therefore, decreasing overall costs. Increasing drill utilization results in an increase in the amount of time the drill is being productive, more drill bit time in ground. Atlas Copco’s theory is that by incorporating directional drilling in the design of a cast blast pattern, a drill rig could drill multiple directional holes, which are the length of the cast blast, from a single drill set up. A drill goes through a series of steps to complete a blast pattern, these steps include: tramming to the hole location, leveling the drill, drilling the hole, cleaning the hole, and retracting the drill steel. This process is repeated hundreds of times until the whole pattern is completed. The most time intensive part of this process is drilling out the blast pattern. Integrating directional drilling into this process could decrease the overall time it takes to drill out a blast pattern by minimizing the amount of time spent tramming and setting up for each subsequent hole. Tramming and drill set up are two aspects of the drilling process where the drill tool is not engaged with the ground and, therefore, not being utilized. A cast blast pattern designed to utilize directional drilling will allow the drill tool to be “in the hole” longer and will improve drill utilization. This change in drill utilization was analyzed. Drilling and blasting is an integral part of the mining process, without it mining would be a slower process and less material could be mined. Drilling provides holes for explosives to be loaded and then blasted. Blasting has been found to be the most cost effective method of fracturing rock in mining for material removal. Blasting is also used as a low-cost method to move the rock in open cast mines, commonly referred to as cast blasting. A cast blast is a large blast designed to allow for the maximum amount of overburden to be removed using explosives in a single blast thereby uncovering more coal at a lower cost. Not all the material is blasted to cast-to-final, which requires that material to be moved with large mining machinery. Material that is considered cast-to-final is material that has been thrown far enough to never be moved again in the coal extraction process, therefore it is in its final resting place. A typical cast profile and cast-to-final area is shown in Figure 1."

Jan 1, 2017

By Robert A. Clifton

It seems probable that more and more minerals will be used in plastics as time goes on. This must occur because the minerals will; aid in processability, enhance the engineering properties, reduce the cost, and above all conserve large amounts of petroleum based chemicals. This paper examines the advantages and disadvantages of using the minerals and the ability of the domestic minerals industry to support this possibly very large undertaking. In the author's opinion, it can. This talk is excerpted from a forthcoming Bureau of Mines Information Circular.

Jan 1, 1985

By Tamara Nestorovic, Luan T. Nguyen

"With the aim to mitigate excavation risks and reduce the costs caused by tunnel boring machine (TBM) stoppage when tunneling under uncertain soil conditions, prediction ahead of the tunnel face has become an increasing interest in the tunneling community. Our research topic is concerned with developing effective concepts for nondestructive identification of geological anomalies ahead of the tunnel face by waveform inversion of reflected tunnel seismic waves. The authors demonstrate that this new technique is promising in providing tunnel engineers with an accurate image of the geological situation that the TBM is going to encounter thanks to the waveforms’ rich information about the geological structure that affects propagation, reflection/refraction and mode conversion behavior of the elastic waves. By setting up a 2-dimensional numerical model for simulation of tunnel seismic wave propagation influenced by a dip layer change ahead of the tunnel face, the authors show that the waveform misfit to be minimized by the inversion process is highly multimodal and therefore propose a hybrid stochastic optimization method that can quickly and robustly converge to the global minimum. DEVELOPMENTS IN TUNNEL ADVANCE EXPLORATION Conventional site investigation by drilling boreholes helps to draw a general image of geological structures along the borehole axes but that image is likely to misrepresent the detailed geological structure due to limited sampled locations. Due to high costs and restricted boring space which deep tunneling and tunneling under urban areas encounter, many industrial and academic research groups have had great interest in developing nondestructive ahead of the tunnel face prediction systems. That means only excitation sources and receiving sensors, which are usually placed on the ground surface or on the side walls or on the cutter head of the TBM, are used for acquisition of the measurement data. The recorded signals in the form of seismic or electromagnetic/ electrical waves, which travel through the geological structure or are reflected back from it, hold the signature of the geological structure of concern, such as geological layer changes, fault zones, erratic rocks, boulders, construction remnants, etc., and therefore can be used to reconstruct the spatial and material properties of those hidden geological structures. Most common nondestructive ahead-of-tunnel investigation systems to date are based on interpretation of reflected elastic/ acoustic waves (seismic waves) and analysis of electromagnetic/ electrical resistivity signals (Mooney et al. 2012). However, due to insufficient penetration depth and spread of signals generated by radar and geoelectric sources, the use of seismic waves for ahead of the tunnel face prediction (tunnel reconnaissance) is more preferable (Kneib et al. 2000; Bohlen et al. 2007)."

Jan 1, 2016

By James C. Hower, B. K. Parekh

Introduction The purpose of coal preparation is to improve the quality of coal to make it suitable for a specific purpose by (1) cleaning to remove inorganic impurities; (2) sizing-crushing or screening, or both; and (3) special treatment, such as dedusting. The properties and quantities of impurities in coal are of major importance in the design and operation of steam generating equipment. Although boilers are often designed and equipped to use a wide range of coals, no boiler will perform equally well with all types of coals. All coals have certain properties that place limitations on their most advantageous use. These limitations are especially stringent for many of the older installations. Because of a general lowering of quality of raw coal in recent years, the need for coal cleaning has significantly increased. Among the factors contributing to the need for increased coal preparation are (1) increased demand for quality brought on by market and environmental requirements; (2) increased extraneous dilution caused by mine, health, and safety laws; and (3) depletion of the higher-quality coal seams. The major characteristics of coal and impurities from the standpoint of mechanical cleaning are particle size composition, generally called size consist; density differences; the relative friability of the coal and its associated impurities; hardness; and strength. Some of the other factors related to preparation are petrographic composition and rank. RANK CLASSIFICATION Coal is a general designation for a great number of solid organic minerals with different compositions and properties; all are rather rich in carbon and have a dark color, generally black. Next to mineral oil and kerogen, coal is the most important reservoir of carbon in the world. Carbon is an indispensable necessity of life as well as the main source of energy. Coals are found in stratified deposits, sometimes at great depths. All coals owe their origins to slow decomposition and chemical conversion of immense masses of organic material. As found in seams, coal is a heterogeneous mixture of organic and inorganic materials. Not only are there large differences in the properties of coal originating from different seams, but also in coal removed from different locations in a single seam. A genetic relationship exists between peats, brown coals, lignites, biturninous coals, and anthracites. As a whole, the process of coal formation, or coalification, proceeds as a continuous transformation of plant material, each phase characterized by a degree of coalification, or rank. As a measure of this rank, the carbon content or some related parameter can be used.

Jan 1, 1991

By T. M. Gurr

Large quantities of phosphate rock are mined and processed in Central Florida (Figure 1). The phosphate rock from the mines is further processed in "chemical plants" to produce phosphoric acid (Figure 2). A by-product of the processing' of the phosphate rock to produce fertilizer chemicals is an impure form of gypsum referred to as phosphogypsum. For each ton of phosphate rock processed, approximately 1.5 tons of phosphogypsum is produced (Figure 3). The typical method to dispose of this by-product gypsum is to stack it in large piles, locally referred to as gypsum stacks or gypsum fields (Figure 4). These gypsum stacks have been the focus of many studies in recent years in an attempt to identify the potential for ground water and/or air pollution associated with the stacks. This paper attempts to discuss some of the ground water impacts and current attempts to minimize these impacts.

Jan 1, 1990

By John G. Kuhm

INTRODUCTION The goal of any development drilling program is the drilling of the exact number of holes necessary to adequately determine grade and dimensions of an orebody, no more and no less. This cost of development drilling represents a large part of the total development budget. Any technique which eliminates unnecessary drilling costs produces beneficial results, both to the company and to the person who can claim the savings. This high development cost factor has produced a quantity of research to develop techniques, for efficient control of drilling programs. Recent mining literature is full of articles describing methods for measuring and increasing the effectiveness of these expensive projects. The method described in this paper was developed during the latter part of a major development drilling project at the Christmas Mine of Inspiration Consolidated Copper Company in Gila County, Arizona. It was used to test the need for drilling individual holes but could be expanded to control an entire project. This technique was used at Christmas as a practical means for evaluating adequacy of drilling on an individual hole basis, and it was possible to eliminate several previously approved holes. Application of this method involves an evaluation of geological conditions present and a good bit of common sense. Projects involving large disseminated, rather homogeneous orebodies of the porphyry-copper type would be the most likely candidate for application of the technique. Discontinuous orebodies would not be amenable to this technique. The method is based on the measurement of the linear correlation between the spatial distribution of two sets of data. The Pearson product-moment correlation coefficient is used. This is a standard statistic commonly used to measure linear correlation between two sets of data. The statistical significance of the correlation coefficient at a 95% confidence level is the main criterion for controlling the project. For purposes of reference we will call our technique the "correlation method" in this paper.

Jan 1, 1971

By D. D. Faulkner

Cable bolts anchored with traditional two component polyester resin cartridges have successfully supported difficult roof conditions in underground mines. Resin cartridges provide a cost-effective cable bolt anchoring system with consistent anchorage performance characteristics when properly installed. The most commonly used cable bolts in the U.S. mining industry are 270 ksi (1,862 MPa), 0.7 and 0.6 inch (18 and 15 mm), seven-strand smooth cable with resin mixing bulbs (also known as bird cages), and 40- and 30-ton nominal capacity, respectively. However, there are other types of cable bolt anchoring systems aside from bird cages. Recently, many questions have been raised regarding the anchorage characteristics of various types of cable bolts. Keystone Mining Services, LLC (KMS), the affiliated engineering company of Jennmar Corporation, conducted a variety of controlled tests developed to closely model actual underground installations. These tests compared the performance of three commonly used cable bolt varieties, including plain, bird caged and indented seven-strand cable. Details of the laboratory testing and comparative analysis of the results are provided.

Feb 23, 2014

By A. L. Mular

A great deal of effort is being expended by mineral processing engineers to acquire a basic knowledge of modelling and optimization techniques. Stimuli such as immediate process improvement, expanded process understanding, optimal flowsheet design and re-design, and the development of new and better control systems are goals which excite the imagination in terms of increased profits. To reach these goals, process models and efficient optimization strategies, regardless of their purpose, assume an important role. Consequently, few of us can argue that such efforts are of no value. The purpose of this paper is to review empirical modelling methods and optimization strategies which appear to be of value to mineral engineers.

Jan 1, 1972

By Charles W. Daugherty

INTRODUCTION The Washington Metropolitan Area Transit Authority's (WMATA's) rapid transit system, Metro, ultimately will comprise 162.5 km (101 miles) of line divided among 10 routes. As shown in Figure 1, about 24 km (15 miles) of the system will consist of mined rock tunnels distributed along the A, B, C and K Routes. The structural construction contracts for all of the A, C and K Route rock tunnels are complete and trains are running in about one-third of them. A contract for construction of rock tunnel section B-9, the southernmost third of the B Route, was awarded on June 27, 1980. The final design of Sections B-10 and B-lla, the remainder of the rock tunnel portions of the B Route and the Metro system, are well advanced and should be under con¬struction by 1982. Of Metro's 87 stations, 11 will have been constructed by mining in solid rock, a not inconsiderable achievement, since each structure must be over 183 m (600 feet) long, wide enough to accommodate two trains and one or two passenger platforms, and high enough to achieve a stable arching action without encumbering columns. With the passage of years, some original priorities have been reordered, and ways have been sought to streamline and simplify this most complex of Metro structures without grossly violating the architectural standards that make it unique. This paper will summarize that search, and describe the design and construction aspects of the resulting product, the dual chamber rock tunnel station.

Jan 1, 1981

By J. J. Renton

The iron disulphide minerals, pyrite and to a lesser extent marcasite, are ubiquitous to coal and coal associated rocks and are the source of nearly all the environmental problems associated with the mining, processing and utilization of coal. The iron disulphides as well as the other minerals in coal exhibit systematic spatial pat- terns of distribution on both regional and local scales and show predictable associations, most of which are determined by the geochemical-sedimentological controls under which they form. It is the purpose of this paper to discuss the geochemical-sedimentological conditions responsible for the formation of coal minerals with special emphasis on the formation of iron disulphides, to illustrate the regional and local patterns of mineral occurrence within coal, to present the microscopic associations of the iron disulphides and finally, to discuss the most important single environmental aspect of the iron disulphide content of coal and coal associated rocks; the production of acid mine drainage.

Jan 1, 1986