Search Documents

By F. N. Kissell, C. D. Litton

This study predicts the level of smoke that miners might meet while trying to escape a coal mine fire and describes how smoke would impede their safe escape. For this study, the authors assumed that miners exit through an escapeway adjacent to the burning entry, that some air would leak from the burning entry to the escapeway. The following conclusions were made: • A very low amount of air leakage to the escapeway can produce a critical level of visual obscurity from smoke. This shows that intake airways may be as susceptible to smoke visibility problems as return airways. • This critical level of smoke obscurity is reached much before a critical level of carbon monoxide is reached. • Small fires can cause a severe sensory irritation that further limits vision. Thus, reliable eye protection is very important. These results show that methods to guide miners through dense smoke will contribute greatly to saving lives during mine fires.

Jan 1, 1993

A machine that improves safety during the cutting of boxholes (ore-passes) and travelways in underground mining operations has delivered impressive results in trials conducted at a South African platinum mine. The technology is a joint effort by Sandvik Mining and Construction and platinum mining company Lonmin. The ABH 1600 boxhole borer was built by Voest-Alpine Bergtechnik, Sandvik’s Austrian subsidiary. It was delivered to the Lonmin Eastern platinum mine in February 2005. There, it was deployed underground on the Number 8 Level (320 m or 1,050 ft below the surface) at the mine’s Newman incline shaft.

Jan 1, 2006

By M. Alley, P. Schroeder, L. Zelazny, S. Nagle

The Old Hickory mineral sands ore body in Virginia (>2000 ha) currently supports a productive rowcrop agriculture. Reclamation experiments were implemented on pilot-scale mining pits from 1995 to 1998. Half of each mining pit was topsoiled (25 cm) while the remaining half was left as either (1) mixed tails/slimes or (2) re-graded subsoil over tails/slimes treated with 112 Mg/ha yardwaste compost. Post-mining productivity was estimated to be reduced by 23%, 3%, 27%, and 20% for each crop (wheat/soybeans/corn/ cotton) in sequence when compared to undisturbed soils. Variability in surface texture and compaction limit restoration of soil productivity.

Jan 1, 2002

By I. S. Parrish

One of the most common errors uncovered while performing a reserve, or resource, audit is not in the geological modeling or grade problems due to poor sampling, prepartion or assaying. The error most commonly found is in tonnage or, more specifically, in the tonnage factor - that factor applied to volume to derive tonnage. Tonnage factors In the metric system, the tonnage factor is the density, or specific gravity. Specific gravity (Sp.g.) is defined by Dana (1947): • "The specific gravity of a mineral is the ratio of its density to that of water at 4° C (39.2° F). • "Density is the mass of the unit volume or weight of the body divided by the weight of an equal volume of water." When Sp.g. is multiplied by the metric volume it yields metric tonnes. In the English system, the tonnage factor is usually expressed in cubic feet per short ton (cu ft/st). When the volume in cubic feet is divided by cu ft/st, the resulting figure is in English short tons. Table 1 gives the cu ft/st factors equivalent to specific gravities from 1.6 Sp.g. to 5.8 Sp.g. The table is based on the following equation: cu ft/st = 0.9072 divided by Sp.g. times 0.02832 The blase attitude that most geologists have toward tonnage factors is echoed in the prevailing definitions of Reserves and Ore, as provided by the US Securities and Exchange Commission (S.C Form S-18), Canadian National Policy 2A and the SME Proposal for Reporting Terminology (SME February 1991). In each case, it is stated that "quantity" (SEC, SME), or "tonnage" (Can.2A), "is computed from dimensions revealed in...." etc. Unfortunately, "dimensions" do not directly yield tonnage. Dimensions must be factored by density to derive tonnage.

Jan 1, 1993

By L. You

Theoretical and analytical analyses of three mitigative measures- plane fitting method, trenching, and tension cable led to the development of a total protection plan to eliminate or reduce damages to the residential structures subjected to surface movements caused by underground longwall mining. The protection plan was applied to twelve residential houses and two external garages. The success rate is overwhelming. This paper describes the methods employed for protection and results of those case studies.

Jan 1, 1986

By Louis W. Cope

Mongolia is known in western countries as the location of rich dinosaur fossil fields. However, the country is even richer in mineral resources. The Ministry of Industry and Trade reports 6,000 mineral occurrences of 80 metals and minerals. Mongolia has already attracted much foreign investment in the mining sector. Mining is the country’s largest industry. It is responsible for 17 percent of the gross domestic product, 65 percent of industrial output and 57 percent of export earnings.

Jan 1, 2006

By G. J. Olson

This paper describes the microbiology basics underlying heap and tank biooxidation of metal sulfide ores and concentrates. The primary organisms are identified and described along with the reactions they catalyze and their growth requirements. Also described is the interaction between ore leaching bacteria and the leaching environment in terms of solution chemistry, temperature, and mineral precipitation. Specific factors and agents that stimulate or inhibit growth and activity of ore bioleaching will be identified. Some of these factors are organism-specific and others are generic for microorganisms that grow under acidic conditions. Current knowledge of the limits of bioleaching in terms of dissolved ions in leach solutions, pH, and temperature will be summarized.

Jan 1, 2003

By R. Patterson

Tracer gases have been utilized successfully in a variety of industries, each with specific releasing and sampling methods. The various attributes of tracer gases are dependent on the industry the tracers are utilized in. Tracers must be chemically and thermally stable, safe, odorless, detectable at low concentrations, have a low background concentration, and should not be naturally occurring in the environment if they are utilized in underground mining applications (Thimons et al., 1974). In addition, the tracer gas should be inexpensive, non-corrosive, non-toxic, easily transportable, readily attainable, and non-radioactive (Kennedy et al., 1987). Sulfur hexafluoride (SF6) met many of these above requirements and therefore was introduced as an ideal tracer gas to use in mining industry in the early 1970?s (Thimons et al., 1974). Due to the nature of underground mining including complicated geometry, irregular flows, turbulent flows, obstructed airways, and leakages it is difficult to use conventional anemometer and smoke tube techniques to accurately measure the effectiveness of ventilation controls (Thimons et al., 1974; Klinowski and Kennedy, 1991). There have been several applications of SF6 as a tracer gas in underground metal/non-metal and coal mines. Thimons et al. conducted early testing of SF6 in an underground limestone mine and determined that it is an effective technique for evaluating auxiliary fans, estimating volumetric flow rates in large areas, and measuring low flow velocities. A rapid face ventilation measurement method (FVM) utilizing SF6 was developed by the Bureau of Mines to make face measurements in underground coal mines (Timko and Thimons, 1982). When measuring the effectiveness of jet fans in dead headings SF6 was proven more effective than smoke tubes (Timko and Thimons, 1982). Experiments related to determining methane liberation in the gob were also conducted by injecting SF6 into a borehole (Timko and Thimons, 1982). Also, in an emergency situation where the gob had to be sealed due to a fire, SF6 was released to determine the effectiveness of the seals (Timko and Thimons, 1982).

Jan 1, 2011

By John Marsden

Despite the recent pullback in metal and mineral prices, and the associated market adjustments, the mining industry is still facing a serious issue with the declining availability of graduate expertise. This is due to a combination of an aging workforce, retirements and retrenchments, coupled with a lack of suitably qualified graduates entering the workforce. The issue has certainly improved since 2004 when the industry picked up the rates of hiring graduate engineers and mining/mineral school enrollments picked up in response. This hiring effort has helped to cover the ?gap? years from about 1985-2000, when industry demand for graduates was particularly poor. However, the recent market pullback is likely to set back this progress, as recruitment and hiring wavers as a result of cost cutting measures and economic uncertainty. A key issue for the mining industry is how to ensure the survival and growth of relevant ?core? degree programs. Such programs include mining, metallurgical, mineral processing and geological engineering. The mining industry needs a healthy, high-level education program to ensure an adequate supply of appropriately qualified graduates for the mining industry. Two-thirds of the professionals entering the minerals industry who graduated within the past 40 years graduated prior to 1985. Since 1985, we have been living off the legacy of graduation classes from the mid-1970s and early 1980s. It is estimated that we have been producing graduates at approximately 40 to 50 percent of the sustaining rate since about 1985. Further growth in the domestic industry would increase graduate requirements significantly, and the export of U.S.-graduates to other parts of the world (as is currently occurring) also impacts the total graduate requirements.

By K. Awuah-Offei, A. U. Rehman

"Information diffusion potential of a social media user affects how quickly information about a mineral project can diffuse through that user. If management can use social media and network analysis, in community engagement program, to understand how fast and how far information will diffuse to communities and followers of particular social media users, it can selectively focus on the most influential users. This paper proposes a method to examine the information diffusion potential of social media accounts. The work uses Gephi, an open source software, to extract and analyze data from different Twitter handles to predict their information diffusion potential. The work uses case studies of real Twitter users (e.g. mining news organizations and bloggers) associated with mining to illustrate the approach. The case study results show that there are significant disparities in information diffusion potential that will demand selective attention. This research will help mines develop effective social media engagement strategies. INTRODUCTION The mineral industry provides raw material for industrial activity to support our society (Martens and Rattmann, 2001). Mines have changed conventional mining practices to sustainable ones because of the negative impacts of mining and increased public awareness (Wang et al 2016). The concept of sustainable mining is getting mature as stakeholders (e.g., governments, investors and host communities) are getting involved in mining projects (World Economic Forum, 2014). The failure of mining companies to address the demands of these stakeholders might result in failure to acquire social license to operate (Thomson and Boutilier, 2011). The social license to operate (SLO), if granted, is mutually beneficial to all stakeholders. Mines prefer being granted SLO and keeping it to avoid any kind of social unrest due to their operation (Prno, 2013; Moffat and Zhang, 2014). Mining communities can grant different levels of SLO; ranging from withholding SLO to psychologically identifying with the project (Joyce and Thomson, 2000; Thomsan and Boutilier, 2011). Most of the previous work to understand community perceptions and SLO in mining is generally qualitative (ICMM, 2012a; Thomson and Boutilier, 2011; Prno, 2013; Moffat and Zhang, 2014; IFC, 2014). In particular, there is limited work on how community perceptions change over time due to information diffusion (Boateng and Awuah-Offei, 2017). However, SLO changes with respect to time (Yates and Horvath, 2013), which can result in risks that are not easy to predict. Mine managers and engineers have a desire to understand these changes so as to mitigate these risks (Que and Awuah-Offei, 2014; Que et al., 2015)."

Jan 1, 2018

By E. D. Attanasi

Geologic resource assessments describe the location, general characteristics, and estimated volumes of resources, whether in-situ or technically recoverable. Such compilations are only an initial step in economic resource evaluation. Forecasts that assume that resources that exist in nature can be commercially produced as needed ignore economic constraints. This paper identifies, by example, the salient features of a geologic assessment that will assure its usefulness for economic analysis. These features are demonstrated with examples of coal resource assessments and coal bed gas assessments.

Jan 1, 2001

By D. R. Dolinar

Geogrids can be used as surface control on both the roof and rib in underground mines to prevent the fall of small pieces of rock and material from between the primary supports. The use of screen material such as geogrid can significantly reduce the number of ground fall injuries caused by these small rock falls. Because of the potential for reducing injuries through the use of screen, the National Institute for Occupational Safety and Health (NIOSH) has conducted tests on screen materials including geogrid to determine their support characteristics and identify parameters that can affect their performance with respect to maintaining broken or failed rock. A specially designed test frame installed in the NIOSH Mine Roof Simulator (MRS) has been used to evaluate the load and stiffness characteristics of the screen material. Two types of geogrids with various designs have been tested-a polyester yarn and a polypropylene grid. The load-displacement characteristics of these grids were determined and the load capacity and stiffness were calculated through 20in of displacement. The load capacity and stiffness of the geogrid in general are shown to be related to the ultimate tensile strength of the screen material.

Feb 27, 2013

By Stephen Davies

Mining at Hudson Bay Mining & Smelting's Snow Lake Division is now in the mature stage of the mines' lives. These base metal copper-zinc mines have been operating for more than 30 years. Stopes had small pillars called "crown pillars" left between them. These pillars range up to 100 m (330 ft) long by 40 m (130 ft) wide and 15 m (50 ft) thick. Hudson Bay have been successful in removing these pillars by using cable slings, electric scoops, longhole mining and diesel load-haul-dump equipment. The different shapes and sizes of these pillars has required that many innovative techniques be tried in order to find acceptable economic mining methods. An overview of the different methods will be outlined. Background Hudson Bay Mining & Smelting's Snow Lake Division is located in Manitoba some 800 km (500 miles) north of Winnipeg and 200 km (125 miles) by road from the Hudson Bay smelter complex located in Flin Flon, Manitoba (Fig. I). There are currently three producing underground mines and one open pit operating at the Snow Lake Division, producing copper and zinc concentrates. Pillar recovery is intensive and vital to continued production of these mature mines. The crown pillars are producing more than 50% of the current mine production. This figure will increase in the future. The two mines at which crown pillar recovery is taking place and that will be discussed are the 400 t/d (440 stpd) Rod Mine and the 1000 t/d (1100 stpd) Stall Lake Mine, both five-day-a-week producers. Crown pillar mining has been applied for some time at these mines. However, it was only recently that the crown pillars became vital to production. This has necessitated a number of innovative techniques to recover them.

Jan 1, 1992

By Willard C. Lacy

A mining operation begins with prospecting and exploration-stages with long periods of investment and high risk of failure. However, success in exploration ultimately determines survival of the mining industry. Prospecting and exploration may discover evidence of a mineral occurrence and outline its size and character, but ore deposits that support mining are "made" through the collective efforts of project geologists, geophysicists, geochemists, metallurgists, engineers, chemists, lawyers, and even politicians (Joralemon, 1975). Some deposits may go through multiple cycles of rejection and recommendation, discovery and development, decline and abandonment, rediscovery and development, etc., as economic, technological, or political conditions change or geologic understanding is improved. Peters (1987, p. 233) graphically illustrates the normal life cycle of a mine and the position of exploration in the cycle (Fig. 4.0.1). During the past fifty years, mineral exploration has evolved from comparing evidence of mineralization of prospects with that of known deposits to a more quantitative science employing many facets of geochemistry, geophysics, multispectral sensing from space, computer data storage, analysis, modeling, and most importantly, a better understanding of ore genesis. This modem approach to exploration began in the late 1940s and continues to develop. Exploration efforts peaked in the 1960s with emphasis upon the search for porphyry copper deposits, Mississippi Valley lead-zinc deposits, and volcanogenic massive sulfide copper-lead-zinc deposits. It peaked again in the middle and late 1980s with emphasis upon micron-size disseminated gold and epithermal and stratiform precious metal deposits.

Jan 1, 2008

The market for titanium feedstocks (ilmenite, rutile,synthetic rutile and slag) is driven primarily by offtake from the titanium dioxide (TiO2) pigment industry. The pigment sector depends on the performance of the global economy. Titanium sponge is the first stage of titanium metal manufacture. It constitutes a minor component (3 percent) of overall demand for titanium feed-stocks. Production and consumption TiO2 pigment consumption in 2004 was estimated to be 4.63 Mt (5.1 million st), up 7.6 percent from 2003. It was driven by strong demand in most regions. In the United States, apparent TiO2 pigment consumption rebounded by 5.4 percent (highest growth rate since 1997) to an estimated 1.12 Mt (1.23 million st), following the decrease in demand during 2003. Chinese TiO2 pigment consumption continued its strong upward trend, increasing by 10 percent to 598 kt (659,000 st) in 2004.

Jan 1, 2005

By H. Arima, T. Fujita, W. Yen

The copper catalyzed gold oxidation and reduction mechanisms in ammonium thiosulfate solution were investigated by Eh-pH diagram based on the optimum reagent combination for 60 mass% -75 µm silicate ore at 16g/t Au with the maximum gold extraction of 92% and the minimum ammonium thiosulfate consumption of 23 kg/t-ore for 24 hour’s leaching at ambient temperature. The gold recovery by cementation was nearly 100% by Zn and Al powders at Metal/Au mass ratio of 30, and around 95% by Cu powder at Cu/Au+ mass ratio of 50. In order to oxidize the gold efficiently with the less thiosulfate consumption, the stable region of [Cu(NH3)4]2+ should be as wide as possible in the region, where [Cu(S2O3)2]3- was more stable than [Cu(NH3)2]+. In order to reduce gold from the pregnant solution with the less metal powder’s (Zn, Cu, Al) consumption, the stable region of [Cu(S2O3)2]3- should be wider than [Cu(NH3)2]+ on copper precipitation. Zinc powder may recover gold more efficiently than copper powder with the similar trend on the effect of ammonia, copper and thiosulfate. However, the large amount of copper will be co-precipitated along with gold since the stability of zinc ammine and thiosulfate complexes are higher than that of copper’s. Aluminium may reduce gold efficiently at higher thiosulfate concentration and pH. These results were confirmed and compared with the optimum reagent combination for finer grind sample at 100 mass% -75 µm, which is the optimum ore size for the standard cyanidation at 1.0 g/ l NaCN to obtain about 95% gold extraction. The optimum reagent combination was concluded as 0.5 mol/l NH4OH, 0.0001 mol/l CuSO4*5H2O and 0.05 mol/l (NH4)2S2O3 with the result of 94% gold extraction and 3kg/t-ore of ammonium thiosulfate consumption. Gold and copper stabilities were well agreed with the result of coarser grind ore thermodynamically. The lower reagent combination will reduce gold oxidation power, but significantly minimize the reagent consumption. From this pregnant solution, nearly 100% of gold was successfully recovered by zinc precipitation at Zn/Au+ mass ratio of 30. Aluminium and copper precipitations resulted in less than 40% of gold recovery at Metal/Gold mass ratio of 30. The reagent consumption cost on this lower reagent combination followed by zinc precipitation was $1.6/t-ore, while the cyanidation was $3.1/t-ore. Thiosulfate oxidation mechanism indicated the similarity to Belousov-Zhabotinsky reaction.

Jan 1, 2002

By C. J. Burkhalter, H. Andrade, T. C. A. Gardner, J. P. Campbell

During the 1990’s several copper heap leach facilities treating crushed and agglomerated oxide and sulfide ore were constructed in South America. The majority of these facilities have been in operation for at least three years, during which time the operators have been able to monitor the performance of the heaps. The basis for the paper is a compilation of these operators’ experiences, leading to a discussion of the lessons learned over the past decade. Several key geotechnical issues are examined, focusing upon the integrity of the ore, drainage material and pipe network, along with the success of any inter-lift liners.

Jan 1, 2002

By Richard W. Graeme, James J. Komadina

Gold Fields acquired an option to purchase the Cerro Corona project, located in Hualgayoc, Cajamarca Department, Peru, in December 2003. In January 2006, the option was taken up and the transaction closed. During the intervening months, project development occurred against the backdrop of a presidential election, increasing national social activism and environmental regulation, rapidly escalating operating and capital costs, as well as an unprecedented demand for engineering and technical skills. Project “Lessons Learned” are discussed in the context of an evolving strategy. The Cerro Corona project forms part of a porphyry copper-gold deposit situated within the Hualgayoc Mining District in northern Peru. It is located in the highest part of the Western Cordillera of the Andes, close to the headwaters of the Atlantic Continental Basin. It lies approximately 90 km (56 miles) by road north of the Department of Cajamarca’s capital city and near the village of Hualgayoc. Access to the Cerro Corona project from Cajamarca is by two roads, one from Cajamarca to the Yanacocha Mine 45 km (28 miles), and then from Yanacocha to the village of Hualgayoc and the town of Bambamarca 45 km (28 miles).

Jan 1, 2007

By Marion Loomis

Environmental regulation is an ever growing cost to the mining industry. Requirements for such items as air quality modeling, hazardous waste disposal, selenium concentration in water and sagebrush planting consume more of the mining industry’s resources each year. The mining industry is willing to make the necessary financial commitments to assure that the air, land and water resources are adequately protected and restored. However, it is sometimes difficult to explain to management and stockholders why money should be spent on a specific issue when science and common sense indicate it is being wasted. Common sense and sound science should dictate how mining is regulated.

Jan 1, 1994

By P. C. Holloway

La Oroya zinc ferrite (19.5% Zn, 26.6% Fe, 0.052% Ga, 0.075% In) was roasted with coal under conditions more oxidizing than normally used in a Waelz kiln, and the roasted residues were leached with 200 g/L H2SO4. Overall zinc recoveries of up to 97% were achieved, with 35% of the zinc reporting to the fume after roasting at 1,100°C with a bituminous coal addition of 20%. Under these conditions, 93.2% of the Cd, 13.4% of the Cu, 33% of the Ga, 61% of the In and 18.2% of the Pb were recovered either in the fume or in the leach solution. At 2006 metal prices, the value of the recovered metals is comparable to that obtained from commercial Waelz kiln processing of this residue. Zinc in the franklinite (ZnFe2O4) mineral is reduced to zinc vapor, and, after oxidation, some of the zinc is found as ZnO or as Zn2SiO4 in the roasted residue. Iron reacts to form either hematite (Fe2O3) or magnetite (Fe3O4), with no metallic iron detected in the roasted residue, and less than 2% of the iron is solubilized during leaching. The residue produced after roasting and leaching is, therefore, much more stable than the residue from Waelz kiln processing and should be suitable for disposal in a landfill.

Jan 1, 2008