Search Documents

By Charles E. Joachim

Railroad and blast induced vibrations were measured in the vicinity of the proposed Big Bend Cutoff. Peak horizontal and vertical particle velocity relations were developed using least squares regression analysis. The dominant frequencies of these data are in the range of 30 to 50 hz. Therefore, allowable charge weight per 30 msec delay curves were generated for buildings (2 in./sec) and unlined tunnels (8 in./sec). A blasting contour map is presented for this site.

Jan 1, 1984

By Andrew Ritter, Victor I. Montenyohl, Stephen R. Winzer

Thirty-seven open pit production blasting operations have been monitored using high-speed cameras running between 500 and 7000 frames per second. Analysis of the resulting films reveals irregularities in timing including sequencing errors and crowding (holes firing less than 8 ms apart), confirming results of laboratory testing of ms delay blasting caps (Winzer, 1978). Where blasting parameters are otherwise constant and within recommended guidelines (stemming, spacing, burden, etc.), timing problems dominate the overall performance of the blasting operation. Model tests in layered Homalite 100, designed to simulate joint or bedding planes in rock, indicate the importance of the stress waves generated by the explosive in developing the crack network which is ultimately responsible for the fragmentation seen in the resulting muckpile. These mechanisms are strongly supported by high-speed film studies at Pinesburg, Maryland. Experiments in controlling relief in deep shots (where depth approaches the lateral extent of the bench blasted) using borehole geometry and hybrid initiation systems (electronic timer and pyrotechnic delays) were carried out. The results suggest that the 1 me/ft. of burden guideline developed by Bergmann et aI., 1974 is too short, and that much longer times are necessary to optimize fragmentation and muck digability. Longer times are found to reduce noise, vibration, and flyrock.

Jan 1, 1979

By Larry Schneider

In 1998, the Blast Vibration and Seismograph Section of the International Society of Explosives Engineers formed a working group to collect and compile a list of regulations limiting ground vibrations from blasting. The goal was to locate those countries, states, provinces, and cities that have such regulations, identify which governmental body enforces them, and determine what limits on ground vibrations are imposed upon the blasting operations. In the course of this study, data was collected from over 60 jurisdictions where peak particle velocity restrictions range from non-existent to very stringent. Some of the regulations were found to be based upon standards grounded in good science, while others possess little or no technical justification. This presentation will summarize the findings of the subcommittee, focusing primarily on what the limits are, which type of blasting operations must adhere to them, and to what structures they apply. The degree to which these regulations are based upon valid scientific and engineering research will be discussed. A listing of specific locations having such regulations and information about those regulations will be provide

Jan 1, 2000

By Don Rapp, Rufus Flinchum

Air blast and flyrock are two of the most critical concerns facing the blaster of today. This paper will provide the blaster with proven procedures for recognizing open face and bench surface problems, explain various surveying methods, and provide the mathematical formulas for calculating and designing proper hole placement and explosive load configuration. A concept called "Pattern Footage" is utilized in conjunction with a USBM study to develop blast designs aimed at minimizing air blast and flyrock. In addition to this main focus, this concept can be used in shot displacement and cast blasting design.

Jan 1, 1993

By Ali Kahriman

This paper presents the results of ground vibration and air blast measurements from tunnel blasting activities during the construction of the Beylerbeyi-Kucuksu waste water tunnel under a residential area in Istanbul, Turkey. Within the scope of the study, the blasting pattern of the tunnel was engineered using Tunnel2000 design software and field studies and measurements for evaluating the productivity and safety of shots were realized for 136 rounds. During the study, the advance of the tunnel, face condition, ground vibration, air blast and neighbours’ complains and comments after every round were observed and the tunnel pattern was improved. Finally, an empirical relation for this tunnel route was developed between scaled distance and maximum amount of explosives, to continue activities in a safe and productive manner.

Jan 1, 2006

By W. J. Birch

The recording of information is critical to the blasting process, whether it be for planning purposes, statutory requirements or environmental compliance. The review and analysis of past data can play a key part in a blast.s design. Statutory records must be held to preserve operational licenses and well-maintained monitoring records are a vital defence for today.s litigious society. However a single blasting event can be responsible for generating vast amounts of data. This information maybe collected pre or post-blast and in their individual ways may have a requirement to be logged, processed, analysed, reviewed and reported before eventually being archived.

Jan 1, 2002

By Dal Sun Kim, Michael K. McCarter

"Comminution (crushing and grinding) of rock materials is energy-intensive and expensive. Mucheffort has been directed to improve the efficiency of conventional milling practice, but relatively littleattention has been given to the potential benefits of blast-induced damage on comminution processes. To help assess this effect, research has been conducted at the IRECO Laboratory and the Generic Center for Comminution at the University of Utah. The objective of this research is to investigate the effect of shockinduced “crack-like” damage on rock properties and subsequent breakage efficiency for three petrologically different rock materials under laboratory conditions. In order to evaluate the effect of shockinduced damage, a quantitative measure of rock damage is needed. For this purpose, a scalar variable (0) is proposed."

Jan 1, 1993

By R J. Hill

Blasters are well aware of the problems and expense faced when trying to load in wet bore holes; problems of poor coupling and poor density, as well as the expense of higher priced cartridge product. In answer to these problems, I developed a system for dewatering using nozzles with lay -flat plastic liners which I have used successfully over the last few years. I found the system not only gave me better shots than I could have expected in the circumstances, but also dramatically decreased costs. The system has been adopted by two large roading contractors and a quarry operation in Eastern Canada.

Jan 1, 1986

By G E. Frantii

In the exploitation of low grade mineral deposits, blasting engineers are vitally concerned with maximizing the efficiency of explosive fracturing of rock while simultaneously limiting deleterious environmental affects to acceptable levels. Efficiency can be inferred from radiating seismic waves. Likewise, seismic waves carry direct information on damage potential. The usual approach to this problem is to measure the maximum signal level close to a blast, where it is difficult to instrument and where the signal complexity is intensified by mixtures of wave types and by local heterogeneities. Near-field sites are usually more easily monitored and more readily interpreted. Therefore, a study is being conducted to determine if variations in multi-hole, delayed blasts produce measurable changes in the spectra of seismic waves recorded in the near-field and if these spectra can be correlated with close-in strong motions and affects. To date, power spectra for the well-developed phase Lg and its early coda have been computed and are found to vary measurably when nominal changes occur in blast conditions. Up to a distance of about 50 km the spectra of Lg and its coda appear to be dominated by body wave characteristics (thus source-controlled), whereas beyond 50 km path affects seem to dominate. Additional data must be collected to fully explore the consistency of near-field Lg observations and to verify their usefulness as diagnostics of the engineering affects of blasting.

Jan 1, 1977

By J Foklesi, G Bohus, D Benedek

The breakage process in blasting takes place in space and in time and the latter will determine the degree of fragmentation, shape of the muckpile and the extent of displacement. The shock wave travels at the velocity of sound in the material and it can easily be measured. The cracks' velocity is only 0.38 % of the velocity of sound. The number of cracks at any distance from the explosion cavity, their length and the time of development can be calculated.

Jan 1, 1986

By Michael McDougall

"Suncor Inc. Oilsands Group, Mining Operation in Northern Alberta, Canada, has beenblasting to loosen the oilsands to increase production and decrease maintenance of the hugebucketwheel excavators for over twenty years. In 1991 an area of the mine wasencountered which had a working face in excess of 130 feet. In order to maintain theproduction objective, the blasting department took on the task of providing as much of ablasted face to work with as possible. In doing this Suncor has exceeded several knownrecords in production blasting."

Jan 1, 1993

By Norman Paley, Zachary Pickett

The Red Dog Mine is a high-grade zinc-lead mine located in northwest Alaska which began operations in November 1989. In June 2014 the upper half of a charge in a trim shot in the Aqqaluk pit deflagrated. No other holes in the area were observed to react and the remainder of the pattern was shot without incident. This was the only known case of a deflagration in the 25 years of operations. As part of the investigation into the cause of this incident rock samples were obtained from the area of this hole and from other areas in this pit. The samples were assayed and tested for reactivity using the Reactive Ground Catalyzed Adiabatic test. Approximately half of the samples were found to be reactive with standard blasting agents. Unexpectedly, some of these were found to be reactive with blasting agents doped with urea to act as an inhibiter. Relationships between element grades and reactivity and between Specific Heating Capacity and reactivity were developed; however, the small sample size led to these models having an unrealistically large number of geological model blocks tagged as reactive. A program to better understand the behavior by testing more samples was initiated. Drill core was selected based on the predicted level of reactivity using the aforementioned relationships. The samples covered a greater range of grades and lithologies and included rock from the soon to be developed Qanaiyaq pit. The samples were dry pulverized then split for elemental assay, Reactive Ground Catalyzed Adiabatic testing, Specific Heating Capacity (SHC) determination, and X-ray Diffraction (XRD) mineralogical analysis. From this data, a Red Dog Mine specific assay based classification for separating reactive from non-reactive ground was developed. Furthermore, it was possible to divide the reactive ground into two subgroups: i) rock which reacts with ANFO-emulsion blends even when manufactured specifically with a reactivity suppression agent like urea and ii) rock which reacts with ordinary ANFO-emulsion blends only when a reactivity suppression agent like urea is absent.

By Joshua Hoffman, Rhys Baker, Tim O’Brien

Numerous agencies in the Executive Branch of the United States Federal Government have regulatory jurisdiction over the explosives industry. These agencies develop the rules by which the explosives industry must operate, and many have the authority to enforce those rules. Likewise, there are entities in the Legislature that have oversight of those agencies and develop the laws that agencies must operate under. These entities in the Legislative Branch are Congressional Committees. Each committee has their respective jurisdictional authority over various agencies and issues. There are several Congressional Committees with jurisdiction over the agencies that govern the explosives industry and they differ slightly between the House of Representatives and the Senate. This paper discusses this division of power as it relates to the explosives industry. Each branch is responsive to the public and the processes through which each promulgates regulation and legislation require public input in different forms. Options for civic involvement for engaging each of these bodies of power in their respective processes are presented. The differences between legislation and regulation are highlighted along with the processes by which each are promulgated. A proper understanding of the governmental mechanics that affect the explosives industry are critical for the industry to be able to be proactive in playing a role in these processes in a democratic way.

By Greg J. Stach, Norman "Skip" Hale

The authors describe the development of an overburden blast casting program in the upper seam of coal at a 2-seam surface mining operation on property adjacent to an active operating underground coal mine. Control of vibration is essential.

Jan 1, 1984

By Claude Cunningham

Late in 1982 a fire began in the shallow, abandoned workings of the Uitkyk Colliery near Witbank, South Africa. Urgent measures had to be taken to quench the fire, before the surface caving it caused could put an important railroad connection out of action. This paper outlines the way in which the job was tackled.

Jan 1, 1984

By Jason Baird, Seokbin Lim

Run up is a factor in Linear Shaped Charge (LSC) cutting for which an account must be made. It occurs on the initiation segment of the charge, and the cutting performance during this period is significantly lower. Previous investigations by the UMR Explosives Group observed that similar effects occur not only with LSCs but a wide range of other explosives applications, including explosive-driven flux-compression generators. Prior to this investigation, it was believed that the main contributing factors to run up were from the combined effects of explosive run up (detonation pressure), lack of confinement at the free, initiation end of the charge, and penetrator transition from segmented pieces to a long-rod penetrator blade. As an initial step to understanding the mechanics of LSC run up, a series of investigations was performed in which the testing series was divided into several sub-categories (explosive detonation pressure run up, lack of confinement and long-rod penetrator concept) in order to reveal the effect of each on the run up. Predominantly, commercially manufactured LSCs were used for the investigation, and the entire testing was completed by the UMR Explosives Group.

Jan 1, 2006

By Tom Donnelly, Roger C. Ilsley

Remote telecommunications seismographs were used to monitor blast vibrations at two historic structures in Cedarburg, Wisconsin during adjacent sewer line construction. The purpose of the vibration monitoring program at the historic structures was to maintain blast vibrations below limiting tolerances established by the Wisconsin State Historic Society.

Jan 1, 1991

By Keith L. Bockelman

The Colowyo mine is a unique surface coal mining operation because it is a multiple seam pit. Using a combination of a shovel-truck and dragline operation, Colowyo mines 8 seams of coal to a depth of 400 ft. Over the past 3 years a number of operational changes have occurred, one of which is the implementation of blast casting. Through this implementation Colowyo has been able to eliminate over one million cubic yards a year, which would have had to be removed by the shovel-truck operation. This has also brought about a significant decrease in the stripping cost per ton within the dragline operation.

Jan 1, 1985

By Dwayne Tannant, Jeffrey Loeb

Blasting techniques and protective measures exist that can mitigate risks associated with flyrock and the nuisance of vibration, and overpressure. However, these are often misused or not used because there are no prescriptive regulatory requirements and typically urban blasting guidelines do not exist. The relationship between the increasingly negative publicity that the urban blasting industry receives and the existing state of regulatory control on blasting in urban environments is presented.

Jan 1, 2012

By Selwyn Pearton

Pumpable emulsion explosives have been available to surface and underground massive mining operations for decades and through their unique properties offer significant advantages through improved safety, reliability and performance. Despite their advantageous properties, the benefits of pumpable emulsions have been unavailable to narrow reef mining operations due to the void in technology necessary for their successful implementation within the challenging environment. Despite efforts to promote and enhance the safety and performance of bulk emulsions for narrow reef stoping, little research has been undertaken to advance the pump technologies required for their implementation. This has resulted in a gap in knowledge and technology and as a consequence the successful implementation of a pumpable emulsion system has consistently eluded the narrow reef environment.

Jan 1, 2015