Search Documents

By M. Q. Xu

During the flowsheet development for a potential commercial Cu/Ni separation plant at the In-co?s Sudbury operation, extensive laboratory and miniplant studies were carried out. There are two potential feed streams for Cu/Ni separation at the existing operation. It is shown that Cu/Ni separation from the rougher concentrate is relatively simple without need of regrind. However, Cu/Ni separation can be difficult from the bulk concentrate because of the presence of excess flotation reagents in the bulk concentrate slurry and locked particles. Excess flotation reagents created excess froth increasing entrainment. By replacing the slurry water with tap water and with addition of some hydrogen peroxide, entrainment is minimized and good Cu/Ni separation is achieved on the bulk concentrate. Fine regrind is required to increase liberation of the locked particles for ultimately high copper recovery at the minimal nickel content.

Jan 1, 2014

By I. Zimbovski, T. Ivanova, E. Chanturiya

"The mechanism of selective action of new reagent-collector AMD of phenylpyrazolone class with sulphide minerals of copper-zinc ores was theoretically and experimentally investigated. The validation was carried out using spectrophotometry, Fourier-transformed spectroscopy, laser scanning microscopy, analytical scanning electronic microscopy and flotation. The reagent AMD in alkaline medium on chalcopyrite and sphalerite surfaces is chemically sorbed, forming strong hydrophobic complexes with copper and zinc. On the pyrite surface, AMD acidifies ferric iron ions with formation of hydrophilic oxidates. The selectivity of collector AMD with separation of sphalerite and pyrite in alkaline condition (??=10) is confirmed by flotation experiments. With AMD, the obtained recovery of sphalerite was 34.4 % at extraction of pyrite of 3 and 6 %. The low recovery of sphalerite is caused by weak collective ability of the reagent. The use of copper sulfate increases the flotability of sphalerite up to 82.0 % at extraction of pyrite of 5 and 2 %. It has been experimentally determined that during the flotation of sphalerite and pyrite by AMD reagent with addition of butyl potassium xanthate, and in the presence of copper sulfate and regulator of formation of ammonium thiocyanate complexes, the recovery of sphalerite is increased to 91 %, while the recovery of pyrite is decreased to 3.8 %. The chalcopyrite is floated actively (90 % recovery). The results of all theoretical research and experiments were confirmed by flotation tests on ores and products of dressing in industrial conditions."

Jan 1, 2014

By A. P. Das

Biomining technology focuses on achieving effective recovery of precious metals from their ores and concentrates using microbial techniques. Biomineral extraction of manganese from low-grade manganese ores using bioleaching was investigated in this paper. Five fungal strains were selected for screening of bioleaching of low-grade Mn ore collected from Sanindpur iron and manganese mines, Koira Sector, Keonjhar, Odisha, India. A fungal strain, Aspergillus niger was selected as it showed high efficiency of manganese leaching. Growth of the fungus was determined in terms of sbiomass dry weight and the final pH was monitored. The selected fungal strain was used for bioleaching of low-grade manganese ore of -150µm size particle size at 2 % pulp density with 2g/100ml sucrose concentration for duration of 20 days. About 60 % of Mn bioleaching was obtained with A. niger. The fungal species proved to be useful for manganese biomining.

Sep 1, 2012

By Yuri Yemelianov, Stanislav Balikov, Alexander Epiforov, Andrey Boldyrev, Andrey Bogorodsky

"Test work was carried out using copper gold-bearing flotation concentrate with 6.85%Cu, 14.30%Fe, 20.70%S and 2.34%As. Gold and silver grade in the concentrate is 54.6 g/t and 92 g/t, respectively. Gold and copper are valuable components in the concentrate. Gold is partially associated with pyrite and fahlores. Copper in the concentrate can be found as tennantite (Cu12As4S13). The 71% of gold from the flotation concentrate is recoverable by cyanidation with simultaneous cyanide consumption in the amount of 96 kg/t. The major reason of refractoriness is that gold is fine encapsulated into sulfides and the presence of cyanicide-copper. The concentrate ground as much as 95% minus 10 µm was treated using low-temperature POX at the temperature of 100±5°C, L:S ratio of 5:1 and the process time of 1-5 hours. Residual sulfide sulfur in the cake is 2.28% which is 89% sulfide oxidation. The highest copper recovery to POX solution is 91%. It was found that gold recovery to cyanide solution is 85-94% during alkaline pre-treatment of POX cakes followed by cyanidation. In this case, cyanide and lime consumption is 75-90 kg/t and 120 kg/t, respectively. In order to recover precious metals from POX cakes leaching using sodium sulfite was carried out. Test work was conducted at varied reagent concentration, L:S ratio and leaching time. Gold and silver recovery achieved was 85-95% and 59-63%, respectively."

Jan 1, 2014

By O. Guven, I. Karaagaçlioglu, O. Ozdemir, M. Çelik

In this study, the effect of morphological properties such as shape factors and roughness of the glass beads on their flotation efficiency were determined using image analysis and profilometer methods. There is a considerable correlation between the shape factors, surface roughness and flotation behavior of the glass sample. These results indicate that as the particle shape is away from roundness and smoothness, it acquires more hydrophobicity.

Jan 1, 2014

By Jochen Petersen, Steven Bradshaw, Guven Akdogan, Ngoie Mpinga, James Mwase, Jacques Eksteen, Cornelius Snyders

"The platinum group metals (PGMs) and associated minerals are particularly refractory to most traditional direct leach processes. However, the remoteness of many new ore deposits, socio-political risks, the scarcity of skilled labor and constraints on the availability of water and electrical power makes it increasingly more difficult to implement the conventional mill-float-smelt-refine process routes to extract and refine PGMs in remote areas. This paper discusses a process to extract PGM’s from low grade ore and concentrate using a sequential stage heap leach process entailing heap bioleaching and high temperature cyanide leaching, and evaluates the feasibility of implementing a carbon-in-pulp process to recover the PGMs from the pregnant leach solution. The heap bioleaching extracts the base metals in an acidic sulfate medium using a mixed culture of thermophiles. After heap bioleaching the heap is reclaimed, rinsed, agglomerated and restacked for high temperature cyanide leaching where the cyanide liquor is directly heated via solar energy in panels. Palladium, gold and platinum are recovered during the cyanide leaching stage. The pregnant leach solution was evaluated for potential carbon-in-pulp adsorption and subsequent elution similar to gold processing. The kinetics of adsorption and elution compared well with gold adsorption and elution."

Jan 1, 2014

By Héctor X. Toro, José Francisco Cabello, Douglas Batista, Álvaro Videla, Claudio Luiz Schneider

The Minas-Rio Project, located in the state of Minas Gerais, Brazil, is currently under construction. The new plant will have a regrinding circuit that uses VertimillTM. The objective is to process itabirite iron ores and it is expected that the consumption of media will represent a large part of the plant operating cost. Many studies in the literature indicate that the size of the grinding media directly influences the grinding efficiency. The size distribution of the charge media is related to the surface area of the charge. In this study, a sample of itabirite iron ore was tested with respect to grindability in a laboratory scale ball mill. The test mill was equipped with a torque device to accurately measure power consumption, as required for the determination of energy specific kinetic parameters. Five tests were carried out with different sizes of steel balls and with SICAM (sub-inch Cast Media). The size distributions of the feed and product of the several grinding tests were used to calibrate population balance model parameters for each condition. The results confirmed that the ball charge with smaller diameter is the most efficient among the different media charge tested.

Jan 1, 2014

The flotation efficiency of magnetic concentrate of the Anhui hematite ore, which includes a great quantity of iron-bearing silicates, has been studied through reverse flotation test with a new type of collector Fly-102. The results indicate that collector Fly-102 has a strong adaptability to the variation of temperature, when the flotation temperature is in the range of 10? to 35?, using collector Fly-102 can obtain good flotation indexes. Collector Fly-102 has a strong adaptability to the variation of the slime contents and grades of the flotation samples. When the content of slime and the grade of the flotation feeds are 30% and 55.63% respectively, under the condition that the temperature is 15?, the open circuit flotation test was carried out with collector Fly-102. After one-stage roughing, one-stage cleaning and two-stage scavenging, a better result is got, the grade of iron concentrate reaches 67.12%, and the recovery of iron concentrate comes up to 84.15%.

Sep 1, 2012

By A. An. Mushketov, A. Al. Mushketov, N. A. Sopina

"INTRIDUCTION At present, more and more metallized raw materials with a metallization degree of not less than 80% are used in the smelting of steel. The main quantity of this raw material is produced in furnaces of mine type. Advantages of this type of raw materials for metallurgical processing are low levels of harmful and slag-forming impurities and a high content of metallic iron. At the same time, the cost of smelting raw materials and obtaining high-quality steels are reduced. In addition to the undoubted merits of metallized raw materials, there are high requirements for the quality of iron concentrates, which are the starting material for metallization: the mass fraction of acidic oxides should not exceed 3%; The mass fraction of iron should not be less than 69%, mass fractions of harmful impurities (phosphorus, arsenic, sulfur, copper, etc.) should not exceed 0.02%. These requirements are dictated by the fact that the recovery of burned pellets is carried out by gas in a solid phase. In this case, the empty rock and harmful impurities from the metal are not separated and sent to the steelmaking unit, increasing the heat consumption for heating and worsening the quality of the steel. The combined production of high-quality concentrate and metallized raw materials requires a large capital outlay from the enterprise, which in the future can be compensated for by increased profit from the sale of more expensive marketable products. At present, in the territory of Russia and the CIS countries Lebedinsky mining-and-processing integrated works is the only enterprise that carries out the entire chain of operations for the production of metallized raw materials, starting with the production of high-quality magnetite concentrate with a mass fraction of iron of 69.5% and ending with the production of a metallized product in the form of hot briquetted gland. JSC «SSGPO» is the largest iron-processing enterprise in Kazakhstan, which processes about 40 million tons of ore per year and receives 16 million tons of concentrate per year with a mass fraction of iron 66.0-66.5%. The technological scheme existing at the concentrator of JSC ""SSGPO"" includes the crushing of the feed ore to the size of 20-0 mm; dry magnetic separation operation; three reduction stages to a fineness of 90-95% kl-0.071 mm; operation of desliming, wet magnetic separation and filtration of the concentrate. Dry magnetic separation of the feed ore makes it possible to remove from the process of 19.6% of the tailings with a mass fraction of the total iron 12.5%, of magnetite 2.2%. The first reduction stage is carried out in rod mills with the volume of 40 m3 to a size of -1.6 + 0.0 mm. The first stage of wet magnetic separation is carried out in counterflow magnetic separators PBM-P-150/200L. The magnetic product of the first stage of WMS is classified in hydrocyclones; sands enter the second reduction stage into central discharge ball mill 3600 × 5000. Runoff of mills enter on the second enrichment stage in counterflow magnetic separators PBM-P-150/200L. The magnetic product enters the classification of the second stage, forming a closed cycle. Mass fraction of the class -0.071 + 0 mm in classifications runoff of the second stage is 70-75%. The second stage classifications runoff is transported toWMS-III operation in semi-counter separators PBM-PP-120/300. The magnetic product of the third stage enters the classification of the third stage. Granular residue are transported to the reduction of the third stage into central discharge ball mill 3600 × 5000. The mill runoff enters the third stage of classification, forming a closed cycle. Classifications runoff of the third stage enters on deslimation. Deslimed product is sent for fine screening to the crasher «Derrick» 2SG48-60W-5STK with a cell size of 0.1 mm. Top size of crasher is sent to regrinding. Undersize with a mass fraction of the class -0.071 + 0 mm 90-95% is fed to the wet magnetic separation of WMS-"

Jan 1, 2018

By Lang Shiping

The criteria for designing a crushing chamber are presented and a program for designing the shape of the chamber is proposed. During the chamber shape design, major design parameters are analyzed first, optimized parameters are determined next and the basic shape of chamber is figured out finally. In the basic chamber design program, the influence of abrasion of basic chamber shape and material characteristic are not accounted for usually. Here, based on the minimum abrasion of chamber shape and uniform particle size theory, the equation for chamber surface curve and the transcending function were formulated and a low-abrasion chamber was designed. Since the chamber shape designed based on experience and experiments is not necessarily the best, optimal design of the crushing chamber shape was carried out. Cubic spline function was used to represent the chamber shape curve and a mathematical model was formulated. The optimal shape solution was obtained using a complex method. Finally, the optimal chamber shape was determined by matching the moving cone stroke S, moving cone speed N and the moving cone bottom angle Thus, superior technical performance of the cone chamber was achieved.

Sep 1, 2012

By H. M. Yang

Structural alteration of pyrophyllite during mechanical activation in a planetary mill was investigated by X-ray Diffraction (XRD) and Fourier Transform Infrared Spectroscopy (FTIR) techniques. Mechanochemical effect markedly promotes the decrease in reflection intensities with increasing the grinding time. Prolonged grinding causes the pyrophyllite to become the amorphous structure. It can be indicated that pyrophyllite is very susceptible to alteration by grinding. Crystal size (d006) of pyrophyllite appears to be a limit after 2h grinding. IR spectroscopy analysis shows a little alteration in the bands of pyrophyllite after mechanical activation. The results indicate that the ordered structure of pyrophyllite is destroyed and lattice deformation occurs. Porous silica was then successfully prepared via leaching the mechanically activated pyrophyllite. Pyrophyllite was first ground for 6 h. Ground samples were subsequently leached with 4 M hy-drochloric acid at 80 °C for 2 h to produce porous silica with specific surface area of 188.1 m2/g, total pore volume of 0.18 mL/g and average pore size of 3.9 nm from N2 adsorption analysis. Otherwise, the porous silica obtained from direct leaching of the original pyrophyllite only has a specific surface area of 4.3 m adsorption analysis. 2/g and total pore volume of 0.03 mL/g. It is inferred that grinding is favorable for the formation of microstructure pores. It offers a simple and convenient route for the preparation of porous materials from natural minerals.

Jan 1, 2014

By M. Vulkov

The paper is focused on the optimal selection of grinding medium for a drum mill. The decision-making is based on the fuzzy multiple attribute approach. One way to optimize the grinding process in a tumbling mill is associated with the development and testing a new shape of grinding body. Family of new grinding bodies ? spheroidal tetrahedrons (tetraballpebs) has been manufactured. Two types of spheroidal tetrahedrons and a classical ball (sphere) with one and the same weight are compared. A fuzzy entropy method to calculate the weight of the attributes is suggested. A grinding body which is the best approximation to the fuzzy formulated technological conditions is selected. Keywords: grinding, spheroidal tetrahedrons (tetraballpebs), balls, fuzzy sets

Sep 1, 2012

By Hristo Stanchev, Veselin Mehandzhiyski, Sashka Kozhuharova, Stefan Stamenov, Alexandar Penchev, Nikolay Nestorov, Velika Stamatova, Ekaterina Todorova

"This article presents the results of comprehensive research on the quantitative distribution of gold content in the raw ore and tailings from the flotation enrichment process at the Ellatzite Med plant. The study is a quantitative and qualitative determination of the presence of gold in the ore processed by Ellatzite Med AD, as well as its behavior and distribution in the various metallurgical products of the flotation process. The representativeness of the samples taken is ensured by the frequency of sampling: four work shifts of sampling on different days within a period of four consecutive weeks. The form of gold present is determined both in the analyzed samples and in separate fractions - granulometric, magnetic, electromagnetic, heavy and light. A summarized diagram presents the phase distribution of gold in the final products of the dressing process. The results obtained are used for further analysis and evaluation of the actual technological parameters of the gold. It was established that an increase in the initial gold content, respectively in the content of native gold in the raw ore, with the current process, leads to an increase in gold losses, mostly in the native gold phase. The conducted analysis of the results from the comprehensive tests on determining the form of gold present in the various enrichment products gave rise to further research with the use of a Knelson centrifugal concentrator."

Jan 1, 2014

By Barun Gorain, Aparup Chattopadhyay

"Many double refractory gold deposits are characterized by the dominance of ""invisible gold"" (sub-microscopic gold) as solid solution or as colloidal-sized particles in different sulfides and other phases. These deposits are mainly composed of silicates and carbonates with moderate clay and mica content and with minor amount of sulfides and organic carbonaceous matters. The presence of highly preg-robbing and finely disseminated carbonaceous matter adversely affects gold recovery in leach circuits. Characterization of carbonaceous matters, commonly known as TCM and quantification of gold associated within these carbonaceous matters along with different sulfide and oxide phases is highly complex and challenging. Studies were initiated on various complex ore deposits and also on samples representing various process streams. This paper presents the development of a systematic approach to gold deportment studies using state-of-the-art mineralogy characterization techniques for quantification of invisible and visible metal contents in various species. The relevance of this mineralogy characterization to metallurgy will also be discussed in this paper."

Jan 1, 2014

By N. Acarkan

Beneficiation of the pyrite concentrate of the Kastomonu-Küre (Northern Turkey) copper ore seems to be attractive due to its high Cu, Co, and Zn contents. Pyrite concentrate were used in the experimental studies. Cu, Co, and Zn were recovered from the concentrate by the sulphatizing roasting, leaching and the precipitation using H2S. Sulphatizing roasting experiments were carried out in a rotary furnace and the optimal roasting conditions were found to be at 650°C roasting temperature and 3.0 h roasting period and addition of Na2SO4 of 3 % for the concentrate containing 0.58% Cu, 0.22% Co, and 0.04% Zn. Then, the roasted product was repeatedly leached with 10 g/L H2SO4 solution. Optimal conditions were found to be 60 oC leaching temperature, 2 h leaching period, and 30% pulp density. Leaching efficiencies for Cu and Co were over 99 %. The valuable metals in the pregnant solution were selectively precipitated by H2S as sulfides. Selective precipitation of Cu, Zn, Co was achieved by adjusting the pH and the temperature of the leach solution. Final metal recoveries of 99.20% Cu, 99.40% Co, and 95.60% Zn were attained. The precipitated sulphides are marketable products. Roasting gases with their 15% SO2 content are suitable for the production of H2SO4 and the leach residues can be integrated with the iron ore processing plant as they contain 57.50 % Fe, 17.70% gangue (SiO2, CaO, etc.), 0.04% S, and 0.06% non-ferrous metals.

Jan 1, 2014

By Qingming Feng, Dongbo An, Jinhong Zhang

The application of the geopolymerization of mine tailings as construction materials is hindered by the fact that conventional geopolymerization of mine tailings usually involves a large consumption of alkali, i.e., sodium hydroxide (NaOH), and a long curing time, because of the relatively low reactivity and the high Si/Al ratio of mine tailings when compared to other active resources such as fly ash and clay minerals. The present study is focused on efficiently activating mine tailings, reducing alkali consumption, decreasing curing time and improving compressive strength. We firstly investigate the temperature effect on the alkali activation of mine tailings during geopolymerization. Secondly, the impact of additives, i.e., calcium hydroxide and aluminium oxide, on the compressive strength of samples is studied. Thirdly, different forming pressures have been applied to remove excessive alkali and its impact on samples' strength has been investigated. The results show that a 40 MPa unconfined compressive strength (UCS) can be achieved with the geopolymerization samples after mine tailings are activated by sodium hydroxide at 170°C for 1 hour with the addition of calcium hydroxide and alkali dissolved aluminium oxide, further compressed with a 10 MPa forming pressure and finally cured at 90°C for 3 days. The findings of the present work provide a novel method for the geopolymerization of mine tailings as construction materials.

Jan 1, 2014

By Thenepalli Thriveni, Seong-Young Nam, Nam-Il Um

New modern water treatment technologies required for arsenic removal from waste waters contaminated extensively by various background sources from mining, industrial waste, agricultural waste, painting industry and natural geological bed rock system etc. Arsenic is a widely dispersed element in the earth's crust and exists at an average concentration of approximately 5 mg/kg. Arsenic (As) and heavy metals may be released from the mine wastes to the ground and surface water systems, as well as the geological environment due to their solubility and mobility. This research focuses on the effect of accelerated carbonation process for successful removal of heavy metal arsenic anions from artificial waste water and mining waste waters. This accelerated carbonation process is a simple and novel method with 85 ~ 88% removal efficiency. Carbonation has been studied as a process to further improve immobilization of solidified/stabilized waste and granular waste. After successful removal of arsenic anions from solid mining waste and its potential benefits for producing construction materials. Besides, the industrial and urban management systems are generating bulk solid mining wastes, and most often dumping them in open fields. To prevent the landfilling with mining waste, many efforts are being made for the recycling of different types of mining solid wastes with a view to utilizing them in the production of various construction materials.

Jan 1, 2014

By Reinol Compañero, Ivy Gonzales, Herman Mendoza, Brian Buenaventura

"The extraction of gold in the Philippines has been a significant challenge for the past decades. Around 70-75% of gold mined in the country can be accounted from the small-scale mining industry which primarily use the traditional cyanidation and amalgamation; processes which have been advocated due to its adverse affects to health and environment. To address this challenge, an alternative clean and sustainable technology was developed for the small-scale miners to recover gold and other metal/mineral values efficiently from Philippine ores. An initial survey was conducted and followed through with extensive mineralogical investigations ascertain the best method applicable. It was determined that Philippine gold occur in ore as (1) very fine particles in the microns range, (2) free-milling, which is in abundance, and (3) locked particles with sulfides --- it was concluded that enhanced gravity concentration and flotation are viable alternatives. A comprehensive test regime was followed to check the response of the ores obtained from different small-scale mining districts across the country. It was shown conclusively that the gold ores respond positively, with recoveries using gravity concentration and flotation of at least 95% and 88%, respectively; exceeding the nominal recoveries using cyanidation or amalgamation. A specific process flow was designed for each type of ore with customized parameters. It was determined that while capital expenditure of implementing these alternative processes is higher than what is currently being used, the operational aspects show that it is much more economical to apply enhanced gravity and flotation. It should be noted that the process developed addresses the critical issue of environmental costs which should be more than enough to justify the shift from the current to the novel and sustainable technologies."

Jan 1, 2014

By S. Fiore, M. C. Zanetti, C. Clerici

The processes and fluxes of a cast iron foundry plant located in the North of Italy were analyzed in order to determine the amount and kind of wastes produced from the different activities. The main fractions are the molding sands, furnace muds and powders coming from the dust abatement plant, the exhaust lime, the furnace refractory, the metallic shotting and the sludges and powders coming from the dust abatement plant of molding lines for a total production equal to 800 t/d. All wastes were sampled and particle-size and chemically characterized to evaluate the best recycling or reuse solutions. Wastes were sieved and divided in three categories according to the particle-size dimensions: below 0.1 mm, between 0.1 and 0.6 mm and above 0.6 mm. The fraction above 0.6 mm dimension underwent magnetic separation to recover and quantify the potentially available iron fraction. The fraction between 0.1 mm and 0.6 mm was chemically characterized in order to understand if it could be fed to the sand regeneration plant. The below 0.1 mm fraction was characterized to evaluate the following recycling and reuse solutions: additive for molding sands and/or raw material for the concrete industry.

Jan 1, 2003

By Agnieszka Surowiak, Tomasz Niedoba

The paper presents a way of determining relations between ash content in coal, particle size and particle density by means of regression, multidimensional Morgenstern distribution functions and kernel approximation. The three-dimensional random vector (D, ?, ?), where D is a random variable describing particle size, ? - random variable describing particle density and ? - random variable describing ash content, where function ?=?(d, ?) is obtained by means of regressive function. The multidimensional Morgenstern distribution functions and kernel estimators with the use of Gauss function were applied to approximate the functions f(d, ?, ?) and f1(d, ?). This approach is a new way of multidimensional description of grained materials such as coal and it also allows to evaluate material features more properly than the classical statistical approach. The results were verified statistically.

Jan 1, 2014