Search Documents

By Steni Stefani, Sanjay Dave

"This paper describes an innovative method, used for the first time in India, for the construction of a 1.0metre-thick positive plastic concrete cut-off wall (CoW) at the upstream toe of the dam at the Kishanganga Hydro-Electric Project in Jammu & Kashmir- India. The extremely difficult bouldery geology with an overburden laden with very hard Panjal Volcanics (quartz, feldspar, muscovite and chlorite minerals) boulders of up to 0.8m to 1.8 metres in size with UCS of up to 265 MPa and the requirement of socketing the CoW into the underlying hard bedrock (UCS 265 MPa) for 1.50m made the choice for the excavation methodology critically difficult. After having evaluated several other existing methods – including hydromill trenchers – the Civil Contractor Hindustan Construction Company, in agreement with its Foundations Engineering Consultant (Ricerca e Sviluppo – Cantieri e Gestioni) opted for a two-stage construction method: firstly, preliminary full-depth drilling and “surgical” blasting with full-length inclinometer checking of borehole verticality to ensure the exact location of rock fracturing and fragmentation coincided with the required position and that it was vertical, notwithstanding efficient trenching into the bedrock of a nominal 1m by 1.5m section; and, secondly, excavation by using heavy duty mechanical rope grabs made locally and developed by the Consultant in collaboration with the Contractor. The details of the methodology and the salient construction data is presented and commented for the 33-metre deep CoW installed at a working platform elevation of 2364.50 m above sea level in a very remote area.BACKGROUNDThe Kishanganga Hydro Electric Project (KGHEP) is a ROR (run-of-the-river) project is located on the Kishanganga River some 140kms North-West of Srinagar, capital of Jammu & Kashmir State of India, for generating 330MW of power in a 90% dependable annual year. The key components of the project are: Concrete Face Rockfill Dam (CFRD), Chute Spillway, Plastic Concrete Cut-off Wall (CoW), Head Race Tunnel (HRT), Surge Shaft (SS), Inclined Pressure Shaft (PS), underground Power House and Transformer Hall, Tail Race Tunnel (TRT).The Power House Site is accessible throughout the year from Srinagar while the remote Dam Site, with its tortuous road climbing the Rajdan Pass at 3556m (11,667 ft) above sea level and several 20-tonne capacity Bailey bridges removed prior to snowfall, remains inaccessible for around 4 months between mid-November to mid-May due to winter and heavy snowfall - the only access is by helicopter, weather permitting. Temperature at the Dam Site drops down to minus 27degrees Celsius during winter, therefore, careful planning from the beginning was most essential for the successful delivery of the Project.This paper deals with the Cut-Off Wall construction which was performed, for the first time in India, adopting a “Drilling and Surgical Blasting” method. However, this technology is not new and diaphragm wall excavation with the aid of drilling and blasting has already been done in some of the projects globally; namely:"

Jan 1, 2017

By Carnevale Francesco, Bracci Laudiero Alberto, Pampanin Piero

"SummaryIn the Port of Naples a slurry wall has been realized through a sandy layer up to a deep tuff layer using the Cutting Soil Mixing technique.The executed panels have dimensions of 2.8 m x0.65 m in plan and a total length of 25 m. Primary and secondary panels have been executed using the wet to wet technique. During the panels execution the following parameters had been measured: injection pressure, injected volume, verticality. At the end of the works an exploratory campaign has been carried out through boreholes collecting samples for laboratory tests in order to verify the diaphragm thickness and its physical and mechanical properties (i.e. unit weight, unconfined compressive strength).The interpretation of the collected data allowed to verify the efficiency of the method, the volume of slurry loss due to permeation during the panels execution, the quantity of the obtained spoil compared to the volume balance equation, both for the sand and the tuff layer.Eventually, the measured physical and mechanical characteristics of the panels have been correlated to the execution method performed.IntroductionIn the Naples Port area there is a polluted site which has to be hydraulically isolated in order to prevent the pollution of the groundwater that flows from land to the sea through the Port area. A hydraulic cut-off wall has to be realized and particularly a slurry-wall realized using the CSM method had been executed.To date, two stretches have been executed, 140 an 110 m in length respectively, as shown in Figure 1 and Figure 2.After execution, the slurry-walls have been investigated with boreholes. In-situ and laboratory tests on the recovered samples of grout have been carried out; furthermore, the geotechnical parameters of the mix composing the wall have been measured."

Jan 1, 2014

By Karl A. H iggins, James P. Racine

"Displacement Cast-in-Place (DCIP) piles are not a common deep foundation type in the Washington, DC Metro Area market. As a result, less regional data is available for these foundations compared to other alternate deep foundation types. Displacement cast-in-place piles (DCIP) differ from traditional Auger Cast-In-Place (ACIP) piles in that the pile annulus is formed by pushing a partially-flighted, auger bit to depth via a large mandrel. The auger bit includes a displacing body near the bottom of the tooling. Therefore, little to no spoils are generated during installation and the soil around the annulus is largely densified in-place due to the displacing body being slightly larger than the mandrel it is attached to.Due to this densification, one would expect that the theoretical DCIP capacities (compression or tension) would be greater than an ACIP pile (assuming a pile of similar length and diameter). After 20 static load tests and the installation of over 6,000+ piles on the MGM National Harbor Casino Project, the differences in pile support characteristics between DCIP and ACIP piles of same size and depth was small. The performance of both pile types depended on the density and type of soil within the bearing stratum. In some early cases of DCIP use, the performance exceeded expectations and appeared to be more in line (or better) than typical capacities obtained from driven displacement piles. Other times, the tip elevations could not be achieved or were so difficult to achieve that installation delays occurred and/or significant additional engineering effort was required to address piles short of their requirement embedment.This paper will discuss the limitations of DCIP pile installation in dense Coastal Plain soils and will present the lessons learned during this project. The paper will also compare the DCIP pile type to both conventional ACIP and driven displacement piles utilizing regional and site-specific load test and installation data."

Jan 1, 2017

By Robert Bachus, Nikolaos Machairasm, Allen Cadden

Data Interchange for Geotechnical and Geoenvironmental Specialists (DIGGS) is a data transfer standard that is gaining widespread acceptance in the geotechnical and geoenvironmental communities. Originally developed using funding from the Federal Highway Administration (FHWA) to efficiently capture data related to geotechnical boring logs, cone penetration test (CPT) soundings, and lab testing results, the data transfer protocol is rapidly gaining traction. It has been shown to have beneficial impacts in other allied areas where disparate parties (i.e., consultants, contractors, vendors, etc.) routinely publish/submit data as part of project deliverables. The historic problem is that many of these submissions use paper copies (i.e., .pdf images) to transmit valuable data for the project… data that may extend beyond the “technical” aspects of the project (e.g., equipment operating conditions, construction production rates, project costs, etc.). These data could be used by multiple parties to assess project performance and safety, as well as to track productivity, etc. Currently, in the limited situations when actual data are compiled and transmitted, the data often are submitted as an author-specific (and often proprietary) software application and must then be re-entered into other software applications (e.g., analysis software, database, etc.) for use beyond simple data collection. An initiative undertaken by the Geo-Institute (G-I) of the American Society of Civil Engineers (ASCE) focuses on exploiting the full potential of DIGGS to geoprofessionals both within and outside of the transportation community. The deep foundations industry represents one community that could benefit significantly from using DIGGS. Data of interest to DFI members include production records, quality assurance information (e.g., verticality and alignment, concrete strength), and, importantly, load test results. When adopting DIGGS, users need not modify how they capture data, but rather will use DIGGS as a vehicle to transfer data to other applications in a standard format where it can be shared, used, stored, and retrieved. This paper and associated presentation will describe DIGGS and demonstrate how DIGGS can be used effectively within the deep foundations community.

Jan 1, 2019

By Martin Pratt

This paper is an overview of deep foundation engineering in Hong Kong past, present and future. The enormity of the subject compared with the space available makes brevity inevitable. Issues of construction and design are covered and some examples of recent challenging projects are given. The content is aimed at those with an interest in foundations generally, but with limited knowledge of the Hong Kong scene. Reference is made to informative publications for further reading on specific topics.

Jan 1, 2000

By Brian P. Waagner

Construction law in general and the law of deep foundations in particular continues to develop rapidly, particularly in the areas of risk allocation. Public and private owners are increasingly using contractual disclaimers to shift the risk of differing site conditions to contractors, and courts are increasingly willing to enforce these contractual devices. Perhaps also in an effort to control costs, public and private owners are turning to design-build contracting techniques. While design-build offers many advantages over traditional project delivery systems, it does not answer all of the risk-allocation questions that frequently arise. Even in design-build, problems with unanticipated subsurface conditions and defective design are not easily addressed. Finally, developments in electronic commerce present the potential to transform the construction industry.

Jan 1, 2002

By Osamu Taki

The development of new auger bits for soil cement column drilling equipment has made it possible to create a homogeneous mixture of soil and cement-reagent slurry. As a result, soil-cement columns are used for foundations of houses and buildings, with reliable results, as demonstrated by many field projects and laboratory tests. This paper presents and discusses construction techniques for soil-cement columns, characteristics of the soil-cement solid, quality control, bearing test results, and soil-cement foundation design procedures.

Jan 1, 1992

By Masaki Kitazume

Deep mixing method, in-situ admixture stabilization technique, has been developed and adopted for on land and marine construction works in Japan. The geotechnical design procedure of the method has been standardized in Ministry of Land, Infrastructure and Transport Government of Japan for port and harbor facilities, which includes the block type and wall type improved grounds for foundation stability, settlement reduction purpose. This procedure is based on the allowable stress concept, in which the induced stresses within the improved ground are confirmed to be lower than the allowable strength in the internal stability calculation. This procedure has been cited by several organizations to establish their standards. The Ministry has a plan to introduce a reliability based design for marine construction works in 2006, in which the design procedure on DM improved ground will also be modified to the reliability based. In the new design procedure, the average and variation of soil parameters and external loads are incorporated by partial safety factors to investigate the stability of improved ground. According to the plan, the author has been studied the design procedure and the magnitude of partial safety factors, and has established a preliminary draft of the standard. This draft will be brushed up through comparing the current design procedure. In this article, the design concept and design procedure of the method are briefly described.

Jan 1, 2004

By William Van Impe

A most renewing and promissing soil displacement screw pile is called the O-pile. The O-screw pile is a soil displacement auger pile based on a screwing in - screwing out procedure. The displacement auger head consists of a discontinuously diameter - increasing steel tip, on top of which the continuous screw flange with variable pitch is mounted. The soil displacement is kinematically ensured by downwardly oriented slots mounted on the auger head at different well chosen locations on the flanges. This leads to a very efficient lower energy screwing-in sequence of the pile and consequently to a high penetration rate. A test loading program of instrumented O-piles has been carried out in order to evaluate the load settlement behaviour, the shaft and tip capacity of the O-pile, including its specific installation parameters.

Jan 1, 1996

Port Gaspé is located on the back side of Gaspé bay and is protected by a natural sand barrier with a length of 2,5 km, from which it got its name, Gaspé Sandy Beach (1). Since 1904 the Gaspé region had a deep water wharf, initially very different, in fact, from the one existing just before the recent reconstruction (2). This wharf with a length of 228 m and a width of 23 m was build of timber cribs. The outside walls of these cribs had been doubled with a wooden wall, creosote impregnated to provide resistance to decay and to the attack of marine organisms (limnorias) (3). Fifteen years ago the upper part of the wood construction had to be removed, because of progressing rottenness and was replaced by an L-shaped reinforced concrete structure (4).

Jan 1, 1987

By Shahriar Vandani, Andy Herlache, Andrew Bro, Wei-Yu Chen

"The Presidio Parkway Project will reconstruct approximately 1.6 miles (2.6 km) of highway, including seven new bridges, three new cut-and-cover tunnels, and a new undercrossing connecting the Golden Gate Bridge to the City of San Francisco, California. The project site is approximately 5.6 miles (9 km) from the San Andreas Fault, capable of producing magnitude 8 earthquakes. Seismic hazards include strong ground shaking, soil liquefaction, ground settlement, and lateral spreading. The Main Post Tunnels (MPT) are two parallel cut-and-cover concrete tunnels approximately 1100 feet (335 m) long. The MPT site underlain by loose sandy soils susceptible to liquefaction and lateral spreading. Excessive racking and permanent displacement due to lateral spreading are identified as the main seismic vulnerabilities. Analyses showed that without ground improvement, tunnel racking of over 5 inches (13 cm) and permanent lateral tunnel displacement of up to 15 feet (4.6 m) could be anticipated. Cement Deep Soil Mixing (CDSM) is proposed to mitigate slope displacements and increase lateral stiffness of the foundation materials to reduce tunnel racking. A series of 2-D fully dynamic time domain analyses were performed to evaluate the performance of CDSM, confirm that performance criteria are met, and optimize the CDSM geometry and replacement ratio. The use of CDSM reduced the permanent tunnel displacement from over 15 feet (4.6 m) to less than 1 inch (2.5 cm). Tunnel racking was also reduced significantly. The adopted analytical approach presented herein can be considered for future tunnel design projects in seismically active areas.Introduction The Main Post Tunnels (MPT) are an integral component of the Presidio Parkway project which will replace the existing facility with a new multi-lane roadway between the Golden Gate Bridge and the City of San Francisco. The MPT are two parallel cut-and-cover concrete tunnels approximately 1100 feet (335 m) in length. As shown on Figure 1, the project site is located in a seismically active area, about 5.6 miles (9 km) east of the San Andreas Fault and 12.5 miles (20 km) west of the Hayward Fault. The San Andreas Fault can generate magnitude 8 earthquakes while the Hayward Fault is capable of producing magnitude 7.3 earthquakes. The design Peak Bedrock Acceleration (PBA) is 0.46g for the upper level design earthquake. The project alignment is shown on Figure 2."

Jan 1, 2014

By John P. Turner, Benjamin J. Turner

"Non-destructive testing and evaluation (NDT/NDE) methods have become standard tools as part of the post-construction quality assurance of drilled shaft foundations. In responding to anomalies, foundation designers, owners, and contractors face a number of choices, including: (i) acceptance of a shaft with known anomalies, (ii) further investigations of integrity (e.g., concrete coring), (iii) repair schemes, and (iv) reject and replace. To assist in selecting the best option, analyses are often performed that involve assessing the structural performance of reinforced concrete shafts that may include defective concrete or voids. Currently, the analytical tools for predicting the flexural strength and stiffness of drilled shafts with defective concrete located in discrete regions of the cross section are limited. This paper presents a robust moment-curvature analysis tool for drilled shafts based on the fiber-element discretization method. The tool allows for consideration of anomalous or defective concrete regions in the shape and location that they are believed to exist in the shaft while considering explicitly the nonlinear material behavior of the intact regions based on expected material properties. A case study is used to illustrate the practical application of the analysis to drilled shaft projects.INTRODUCTIONImperfections such as defective concrete or accidental eccentricity of reinforcing cages are an inherent part of the drilled shaft construction process that will occur occasionally even when construction best-practices are followed. Petek et al. (2002), O’Neill and Sarhan (2004), Poulos (2005), and others have described the effects that construction defects can have on the axial and lateral performance of drilled shafts. Our industry has seen rapid progress in recent years in the development and improvement of tools for detecting drilled shaft anomalies, such as gamma-gamma and crosshole-sonic logging, sonic-echo testing, thermal integrity profiling, and even visual inspection with invasive video cameras. Nonetheless, in most cases the wealth of data from these tests is used by foundation engineers to make a fairly “black or white” decision—should the defects be repaired, or should the shaft be rejected? A third option that is not typically considered is to directly analyze the section, including anomalies, and compare the reduced strength and/or ductility to the actual project demands. This option takes full advantage of the data collected during integrity testing, and may provide a justifiable means for avoiding further construction costs and delays, whether for repair or replacement."

Jan 1, 2016

By F. Z. Suo

Baoahan Iron and Steel Complex is situated at lower beaches of the Yangtze River. The subsoils 50~70 M below the surface is a deposite of Yangtze River delta, consisting mainly of weak silty clay and loam, with low soil bearing capacity. Consequently, to build on such a weak soil a grant iron and steel integrated works weak soil improvement at the Complex, pile foundation is the effective type. It is estimated that at the first stage of Baoshan project 60,000 piles have been driven, of which 60% are steel pipe piles and 40% reinforced concrete piles. To provide reliable basis for pile foundation design, on-site loading tests were carried out for long reinforced concrete piles 27,45 60 M in length ,with strain gauges on the chief reinforcement of pile shaft and strain rod on pile tip. Based on loading tests, the paper discusses and analyses some issues, including determination of load transfer mechanism distribution of frictional resistance. Tests show that as far as long friction piles in soft clay are concerned, regardless of the properties of pile tip's bearing stratum, loads are mainly carried by shaft frictional resistance which it is effective to determine pile capacity in terms of P ~ S relationship.

Jan 1, 2010

By David R. Beadman

The Fleming method is widely used for the analysis and prediction of single pile behaviour under maintained loading. The method does not distinguish between bored and driven piles. Driven piling avoids the need to dispose of spoil from the pile installation and is therefore becoming increasingly attractive. This paper considers the theoretical effects of the possible preload at the base of a driven pile after installation, using the hyperbolic functions as defined by Fleming. The Fleming method is reviewed and the equations and analyses are adapted, using spreadsheets, to allow for a possible preload. The simplifying assumption of the effect of the elastic compression of the pile is also reviewed and a more analytical method adopted to assess the elastic compression. Some driven pile test data is analysed to consider the possible effects of the preload on the performance of a driven pile and to test the theoretical relationships that are developed in the paper.

Jan 1, 2006

By Bjöm Böhle

Top-down construction (or cut and cover construction) is providing important advantages when comparing with conventional construction techniques for commercial developments with deep basements, underground car parks or near surface infrastructure and traffic tunnels. Main features are substantially reduced restrictions to surface usage, avoidance of intervention with adjacent property, provision of rigid substructures resulting in minimal deforma­tions and settlements and, last but not least, accelerated construction pro­gramme. The present contribution illustrates the construction method in general and elaborates in detail on the special foundation works for a major urban commercial high rise development requiring a six level basement structure.

Jan 1, 2006

This manual provides basic practical instruction on the inspection of driven piles. It covers the essential components of pile driving, such as the pile driving hammer, hammer accessories, the pile and soil, and frequently encountered test methods in an uncomplicated, yet knowledgeable, and practical manner. Insight is given into the methods of installing the foundation, dealing with the cranes which do the lifting, the hammers which do the driving, the leads that guide the hammer and pile, the compressors which provide the external power when required, and finally prevalent analysis tools and testing instrumentation and procedures which enable you, the Inspector, to do your job. This DFI Inspector's Manual for Pile Foundations will help the Pile Inspector who has limited knowledge of pile foundations. Perhaps this Inspector has been pressed into service at a moments notice; a few helpful hints and suggestions to him are desperately needed and he can look here for the basics. It is also useful for the experienced Pile Inspector as a reference guide. However, this manual is not a detailed check list of every possible scenario and detail which could ever be encountered. There are other sources available which give more detailed descriptions (and should be consulted by the Inspector when appropriate; a list of this additional reference material is provided and suggestions made in appropriate chapters of this text). The current manual is more a brief "textbook overview" with some of the more important aspects given at least some emphasis so that the Inspector has some direction and hopefully helps to produce a safe, yet economical, foundation.

Jan 1, 1997

By M. B. Wechsler

An analysis is developed for determining the maximum loading, as well as the potential uplift of the piles on bridge pier foundations. There are considered piers supported on two through seven rows of piles, and related to two simply supported collinear superstructures of any structural material. The study leads to different types of influence lines for various load combinations. For load combinations containing vertical loads only, the related influence lines are similar to those as for the bending moments of a virtual span covering the two actual spans, as well as the gap between the two superstructures; and, in this case, the heavier loads should be positioned in the vicinity of the pier. While, in the case when vertical loads are acting together with hori­zontal forces, the related influence lines will indicate where the heavier live loads should be positioned. And they will also indicate on which portions of the spans the live load should be avoided.

Jan 1, 1989

By Raffaella Granata, Wesley Schmutzler, Matteo Bertoni

"The Lower Wood River Levee system, at the confluence of the Wood River Creek and the Mississippi River, in East Alton, Illinois, has been plagued with underground seepage and, in 2010, remediation was deemed necessary by the Southwestern Illinois Flood Prevention District Council and the United States Army Corp of Engineers (USACE). The experts enlisted by the council produced a design that provided for constructing a cutoff wall approximately 2,000 feet long and up to 140 feet deep, through alluvial and outwash soils, and embedded in bedrock. This paper will describe the challenges faced by the Quality Control (QC) and Quality Assurance (QA) teams due to the complex nature of the project in conjunction with an extremely thorough QC/QA program.INTRODUCTIONThe “American Bottom” is an area of 453 km2 (175 square miles) in Southwestern Illinois, extending from Alton south to the Kaskaskia River, which is home to 156,000 people. In the 1940s and 1950s the U.S. Army Corp of Engineers (USACE) designed and built a 120 kilometer (74 mile) long levee system to protect the area from a 500-year flood event on the Mississippi River, which flows through it. The levee system has been plagued by under-seepage for several years. The phenomenon has worsened to varying degrees, depending on location, to the point that remediation was needed.The Southwestern Illinois Flood Prevention District Council (SIFPDC), to obtain Federal Emergency Management accreditation, in June 2010 commissioned a team lead by Amec Foster Wheeler for the design and management of the required levee improvements. The team presented in 2011 the project’s first set of drawings showing proposed design features throughout the levee system. The project was subdivided in four areas, based on the controlling levee districts, one of which, the Wood River Drainage and Levee District, was split into three subdivisions: Upper Wood River, East-West Forks of Wood River, and Lower Wood River.The project included the installation of a cutoff wall at the confluence of the Wood River and the Mississippi River in East Alton, IL (Fig. 1). The Engineer of Record (Amec Foster Wheeler) considered the cutoff wall as the only viable solution to stop the severe under-seepage that was undermining the integrity of the Lower Wood River Levee. The Lower Cutoff Wall (LCW) project is the subject of this paper."

Jan 1, 2017

By Michael J. Brown

It is often necessary to undertake some form of pile testing to verify design calculations. Historically this has been limited to static and dynamic tests. Newer rapid testing methods such as Statnamic are seeing more frequent use. This form of testing can be advantageous due to short set up time and test duration. Although the methodology suffers from a lack of formalised guidance and may prove difficult to analyse in certain soil conditions. This paper investigates the suitability of Statnamic testing and analysis for a range of soil and pile types as well as different installation methods through a number of case studies undertaken in the UK. Recommendations are made on test specification and analysis.

Jan 1, 2006

By Alexi J. Neill

"This presentation will showcase two challenging projects with deep excavation support systems in the Atlanta area where state-of-the-art instrumentation and monitoring systems were used to manage risk by confirming design performance requirements / calculations during construction. The instrumentation and monitoring system successfully reduced risk by recording real-time data on a project website while simultaneously sending email alarms to key site personnel when data exceeded pre-determined alarm thresholds. The monitoring data revealed unexpected performance at an early enough stage so that contingency plans could be engaged and remedial efforts devised in order to limit the consequences. Finite element analysis was used to model deformations, analyze the unexpected performance, and prepare theremedial design.INTRODUCTIONConstruction in densely populated urban areas is becoming more common in order to keep up with the increasing infrastructure demands of our growing population. America’s big cities continue to outpace the overall nation in population growth. The city of Atlanta, the nation’s ninth largest city based on metropolitan population, is a prime example of this. The population has grown at a rate of 6.6% between 2010 and 2013, nearly triple the overall growth rate of the United States during the same period (SustainAtlanta, 2015).As a result of increasing infrastructure demands in Atlanta, developers are now constructing larger buildings on smaller properties. In addition, developers are attempting to maximize space on their selected properties, often by designing underground parking garages to accommodate as many cars as possible on these compact sites. In some cases the selected sites are adjacent to buildings, utilities, and other existing structures. The risk associated with construction increases during underground work that requires a support of excavation system, particularly on confined sites adjacent to existing structures. There is a risk posed to people, property, and the environment that the project team should monitor when constructing in these conditions."

Jan 1, 2016