Search Documents

By G. A. Kosick, G. S. Dobby

"This paper presents the principles and application of a recently developed control system for flotation columns and column circuits. The control system uses triple pressure sensors to directly sense zone densities and level, and to help in characterizing the operating behaviour of individual columns. A complete expert system development tool is incorporated within the system to provide the facility for full operator training, an on-line help facility, and a means for incorporating the column behavioural patterns into decision making rules. The system is configurable to any number of columns and can be run in either supervisory mode or direct control through Minnovex PIO software. Additional process signals can be interfaced with the system if desired. Operating experience with the control system on the Minnovex column flotation pilot plant is described.I: INTRODUCTIONColumn flotation cells have been more difficult to control and are more sensitive to circuit changes than conventional mechanical flotation cells. This susceptibility encouraged investigation into various types of control strategies ranging from inexpensive single pressure measurements for level control, to highly instrumented and expensive systems using a variety of control methods.Flotation operators, in many cases, do not understand the column control philosophy or have not been trained to deal with this new type of cell. Some operators have subsequently absolved themselves of the column operating responsibility. Some column cells, for example, have run for hours with slurry pouring over the top or no froth coming off at all.ColumnEX is a column flotation control system which was developed from the viewpoint of an operating shift foreman who wishes to:1. control the column or column circuit through a genuine understanding of what is happening inside the columns, and2. to share this knowledge with his flotation operators and be available to guide them through times of circuit upsets."

Jan 1, 1990

By Wei Sun, Jaewon Choung, Zhenghe Xu, Zhangming Cui

"High intensity conditioning has been demonstrated in a number of cases to enhance fine particle flotation. The improvement could be attributed to the enhanced formation of particle aggregates. However, the understanding of aggregation mechanisms remains rather limited. Recently, an enhanced particle aggregation was observed by the formation of small air bubbles resulting from high intensity agitations (HIA). In this study, a novel visualization system is designed and constructed for characterizing the fine bubbles formed in an HIA cell. The new design allows determination of gas evolution and bubble size distribution. With this system, the effect of dissolved air on fine bubble generation by HIA is investigated. The results show that HIA creates a favorable environment for the formation of gas nuclei and small size bubbles due to hydrodynamic cavitation.INTRODUCTIONFlotation is a dominant separation technique employed by mineral industry to recover the valuable mineral particles. However, in general, particles finer than approximately 10 µm are not effectively recovered by conventional froth flotation technique due to their low inertia and high specific surface area (Fuerstenau, 1988). Therefore, the fine particle flotation has been considered as the central challenge of flotation research. Substantial advances have been made for fine particle flotation from both a theoretical and technological point of view (Fuerstenau et al., 1979; Song and Lu, 1990; Subrahmanyam and Forssberg, 1990; Sivamohan, 1990; Sedat and Barry, 1991; Matis, 1995). High intensity agitation (HIA), for example, has found some success to improve fine particle flotation kinetics in laboratory tests (Chen et al., 1999a and 1999b; Valderrama and Rubio, 1998; Rubio and De Brum, 1994).The effect of mechanical agitation on flotation kinetics has been recognized for many years. In mid-1970s, Warren (1975) reported that increasing the shear rate of the pulp could improve the efficiency of ultra fine particle flotation. He attributed this improvement in flotation to the formation of aggregates. This concept of aggregation has been extended by Rubio (1978), and Bulatovic and Salter (1989), who employed high intensity agitation (HIA) method to promote aggregation. They found that HIA with the addition of collectors, frothers and suitable modifiers significantly improved both the flotation recovery and selectivity of ultra fine sulphide minerals. The improvement was explained by warren’s shear flocculation theory. Till now, many studies (Chen et al., 1999a and 1999b; Valderrama and Rubio, 1998) have been undertaken to improve fine particle flotation by HIA. However, most of these studies were focused on the relation between energy input and flotation efficiency. Less information was available for describing how the aggregate formed during HIA process."

Jan 1, 2006

By Martin Kesting

The world wide growth dynamics and the continuously growing demand for energy, results in increasing energy prices. Looking from this point, the efficient exploitation of fossil fuel deposits has become a more important factor to the production of energy raw materials than ever before. This shall be reached by an increase of the automation degree of the bucket wheel excavator in the open pit mining as well as a quality increase of the entire mining process chain. A further optimization of this operation can only be achieved by gathering additional information about the input parameters. The earlier and more exact the description of the input parameter, the greater the effectiveness of the entire process chain. To address this major issue, the RWE Power AG assigned the Institute for Transportation and Automation Technology with the research project "SIMT, Sensory Identification of Material Type and Detection of the Interfaces" [Kes07]. Presently, the control of the bucket wheel excavator is carried out manually by the operator, as well as the visual identification of the different geological layers and the energy raw materials. In this paper, a sensor-system is introduced, which was developed in order to transfer the manual material identification and detection of interfaces into an automatic online procedure. A special challenge and the main focus of this contribution is the integration of this sensor system into a bucket of the bucket wheel excavator. For measuring procedures where direct contact with the in situ material is necessary, the sensor has to be integrated into the bucket. Since direct contact with the material is not necessary, it can be integrated next to the bucket wheel. The results of a preliminary study show that although there is a broad spectrum of sensor technologies for material and interface identification, only a few are suitable for an application in on-line measuring at the bucket wheel excavator. Taking into consideration the demands on the sensor technology, the studies carried out and comparable applications of individual sensor technologies which have already taken place in practice, the integration of the following measuring systems have been realized: ground penetrating radar / reflection measurements, geo electric, resistance geo electric technology. The solution developed in the research project offers for the first time the direct integration of sensor systems into the bucket of a bucket wheel excavator. It will now be possible to test other measurement methods and sensors, not only for the ones already mentioned. As an example the integration of a triaxial accelerometer to measure the solid borne sound and vibrations concerning the cutting of different materials will be shown.

Oct 1, 2009

By Kimiz Dalkir

Some things to keep in mind? ! What is your role in knowledge management? ! What knowledge-related challenges are you facing today? ! How does important knowledge get shared in your organization? ! Can you name factors that enable/block innovation and organizational learning in your work context? A brief history of KM? ! Top-down / imposed ! Rigid / bureaucratic ! Slow deployments ! Expensive ! Unpopular: empty libraries, info-junkyards, low adoption rates ! Problems measuring success ! The result: traditional KM is not the answer

May 1, 2003

By Kevan Ford, Getulio Junior, Rob Henderson, Wayne Philips, Chris Martin, Rob Thorpe

"Plant 2 at the Kinross Paracatu gold operation in Minas Gerais State, Brazil, was commissioned in late 2008. Designed to be the largest tonnage, lowest grade gold milling operation in the world, Plant 2’s throughput has steadily increased towards its design capacity of 5087 tons per hour.The plant employs a gold-specific flotation scheme to recover the majority of gold, which is present as discrete free gold particles. Additional gold is recovered by jigs in the grinding circuit, and the jig concentrates are reground, upgraded and subjected to intensive cyanide leaching. The flotation cleaner concentrate is reground and leached using a conventional CIL circuit.One year after start-up, with the plant stabilizing operationally, plant circuit surveys were completed by a joint team from Kinross Paracatu and Blue Coast Metallurgy Ltd. The surveys audited the flotation and concentrate treatment circuits to investigate the metallurgical performance.This paper describes the Plant 2 operation and how the surveys were designed and executed. Some of the quality control systems that were employed to provide meaningful data from such a low grade gold ore are described and findings and actions taken to improve metallurgy as a consequence of the surveys are discussed.INTRODUCTIONThe Paracatu mine is located two kilometres north of the city of Paracatu, in the north western portion of the state of Minas Gerais, Brazil, 230 km southeast of the national capital Brasília (shown in Figure 1). The present day Paracatu mining operation, fully owned by Kinross Gold, through its Brazilian subsidiary Rio Paracatu Mineração (RPM) is designed to be the largest tonnage, lowest grade free milling gold operation in the world.The deposit currently hosts some 1.2 billion tonnes of ore at a grade of ~0.41 g/t gold, hence contains a total gold reserve of over 20 million ounces. At a designed plant throughput rate of 61 Mt/year the mine life goes beyond 2030."

Jan 1, 2011

By Henry Stoch

It?s a green, green world ? Public concern about the impact of human activities on the environment and the roles that businesses play in that impact is rising. What?s happened in the last few months? ? Recent news: ? British Columbia announces carbon tax in 2008 budget ? Federal Court ruling stalls oil sands approvals due to a lack of consideration of GHG implications ? US Energy Independence and Security Act could limit government procurement of oil sands-derived fuels ? Western Climate Initiative (WCI) suggests a ?first seller? approach for regulating generators outside WCI jurisdictions ? Implications ? A cost for carbon has arrived ? The lack of a GHG strategy can have a material impact on your business ? Regulations in other jurisdictions could affect your organization

May 1, 2008

By R. Dahlke, J. A. Finch

A campaign was undertaken during the greater part of 2001 at Noranda’s Brunswick mine concentrator to investigate the role of gas (air) superficial rate (Jg) distribution to the cells in the final Zn cleaning stage (bank of seven cells), i.e. the Jg profile. Three profiles were tested: “balanced” (each cell with same Jg), “increasing” (from cell 1 to 7 proportionally), and “decreasing,” along with an “as found” profile in a parallel control bank. The experimental design allowed for two confounding factors, changes in ore type and circulating load. The increasing profile consistently gave the best metallurgy (down-the-bank grade / recovery). The reason for improved performance was the response of the first cells in the bank where the increasing profile gave the highest selectivity of sphalerite against nonsulphide gangue (NSG). The other profiles gave lower selectivity and higher zinc recovery in the first cells, which combined to reduce overall bank performance. The higher selectivity with the Increasing profile is attributed to the low gas rate in the first cells reducing water recovery and hence limiting entrainment of NSG. The increasing profile was subsequently configured for all four stages in the zinc cleaner circuit.

Jan 1, 2004

By Margarete Kalin

"Biotechnological approaches to decommissioning of mine waste management areas are presented in the context of sustainable environmental management. Improved design of waste sites and environmental management paves the way for the application of new technological approaches. Mining wastes are better confined, effluent quantity is reduced and the quality is expected to improve in the future. The biologically mediated treatments focus on the creation of conditions inside the waste management area which lead to the confinement of the contaminants in the inactive tailings ponds and seepage collection ponds, as well as pits or other disturbed areas which were part of the operating conditions.Biogeochemical reactions lead to three fundamental water treatment steps mediated biogeochemically , alterations in chemistry which lead to formation of particles, which then have to flocculate and be assisted to collect in the bottom of the ponds. Microbially active sediments are installed to assist particulate formation and serve as sinks for metals. In deeper sediment strata, stable forms of metals are created. Biological polishing is used to collect the particulates and relegate them to the sediment. Examples will be given of the application of these processes, to waste rock piles, open pits and tailings ponds. This paper attempts to show that, through the integration of applied biotechnological advances and the application of new approaches to decommissioning, reductions of environmental impacts by mining are possible. * Note: this paper has been presented at the 13th Annual Meeting of BIOMINETIntroductionThe role of biotechnology in decommissioning of mining waste management areas should be placed in the context of sustainable development. The concept of sustainable development as defined by the Brundtland Commission (1987) for the restoration/ reclamation of mining operations could be translated as follows: The increasing demand for the resources by the world population must be met in a manner which does not compromise the earth's environment over the long term (Brooks et al., 1995)."

Jan 1, 1998

By T. R. Raponi

"The Williams Mine, Canada's largest gold mine, processes over 6,000 t/d of ore utilizing SAG/ball milling, leaching and CIP, carbon stripping, electrowinning and refining to produce gold dare bullion.Grinding accounts for over 50% of milling costs with grinding media, power and mill liners making up over 75% of grinding costs. Since 1991, several changes in these areas have been made which have significantly reduced costs, while fineness of grind and mill recovery have both been increased.This paper discusses the changes made in the grinding circuit over the past few years and assesses their impact on operating costs and mill operations.IntroductionThe Williams Mine is located in the Hemlo area of northwestern Ontario, about 40 km east of Marathon. It is operated by the Williams Operation Corporation, which is equally owned by Teck Corp. and Homestake Canada Inc. Canada's largest gold mine, the Williams Mine commenced operation in October 1985 at a rate of 3, 000 t/d. Mill throughputs have typically exceeded design, averaging 3, 397 t/d in 1986, and 3,380 t/d in 1987. In August 1988, production was increased to 6,000 t/d. Throughput averaged 4,212 t/d in 1988. Production increased over the next few years averaging 5,477 t/d in 1989, 6,248 t/d in 1990, 5,987 t/d in 1991, and 6,283 t/d in 1992. With a recovery of over 95.5%, production for the first three quarters in 1993 is averaging 6,408 t/d.GeologyThe main ore body is a steeply dipping conformable zone of microcline-quartz-muscovite rock. It occupies the contact zone between hanging wall metasedimentary rocks and foot wall felsic quartz feldspar porpyritic rocks of possible volcanic or subvolcanic intrusive origin. The ore body is enveloped by muscovite schists which are thickest on the footwall side. The schist is enriched with tourmaline, pyrite, and green mica containing vanadium and barium. The ore body contains pyrite and barite which occurs mostly in laminae and bands to veinlets and breccia fillings. The gold occurs as free (native) grains, 20 to 30 µm in size at grain junctions of the microcline and quartz. Visible gold is rare in the main zone. There are commonly two or more discernable layers of economic value which are separated by weakly gold mineralized material which usually consists of muscovite schist, barite rich zones or sulphide poor-microcline-quartz rock and in the upper and western fringes by biotite rich schist with feldspathic fragmental characteristics. Molybdenite is a common constituent as very fine disseminated grains in the microcline-quartz rock and is most prominent with gold enrichment. Stibnite and realgar are two of the more common accessory sulphides."

Jan 1, 1994

By Brian Hart, Hong Zhong, Liuyin Xia, Kyle Douglas

"The application of hydroxamic acid as flotation collectors is fast becoming of significant interest for the selective flotation of oxide minerals along with upgrading oxidised based metal ores and minerals. In the hydroxamate molecule, both O and N atoms in the -CONHOH group are identified as coordination atoms in many complexes and their characteristic structure determines the strength of the chelation complex between the hydroxamate and metal ion. The chelating performance of hydroxamates with transition metals including Cu, Ni, Zn, Fe, Cr, Mn and Co, the alkaline-earth metals (Be, Ca) and heavy metal (Pb) has been studied. Cytec has developed and patented a range of alkyl hydroxamates as flotation collectors for oxidised base metal sulphides, metal oxide minerals and precious metals. This paper introduces two new structures of hydroxamate collectors (Cyclohexyl and 4-tert-butylbenzoyl hydroxamates) and evaluates their characteristics relative to alkyl and benzoyl hydroxamates. Laboratory small-scale flotation tests were conducted with ilmenite and wolframite. The use of 4-tert-butyl benzoyl hydroxamate resulted in a best flotation performance for ilmenite. A relatively low cyclohexyl hydroxamate dosage was required in the flotation of wolframite to obtain comparable results to the alkyl and benzoyl hydroxamates. It is also shown a significantly improved flotation performance with 4-tertbutyl benzoyl hydroxamate in the flotation of ilmenite plant ore in comparison to the oleic acid or fatty acid collectors typically used for ilmenite flotation.INTRODUCTIONHydroxamic acid has been reported as an effective collector in small-scale flotation tests for a wide variety of oxide minerals and ores including copper (Lee et al., 1998, Lee et al., 2009), iron (Quast, 2000), tin (Sreenivas and Padmanabhan, 2002; Wu and Zhu, 2006), tungsten (Marinakis and Kelsall, 1987; Xia et al.,2004), and rare earth metal minerals (Ren et al., 1997; Pradip and Fuerstenau, 1991; Assis et al., 1996; Pavez et al., 1996; Zheng et al., 1996; Chen et al.,2005).As part of our previous research project, a selected suite of hydroxamic acid collectors including fatty, aromatic and modified hydroxamates (naphthoyl, cyclohexyl, benzoyl, octyl, 4-tert-butyl benzoyl, salicylic hydroxamates) were tested in order to examine their potential for recovery and selectivity of rare earth minerals. In these tests it was shown that the flotation performance with the hydroxamate collectors was significantly better than the phosphoric acid collectors on no slimes removed samples (Brian, et al., 2014; Liuyin, et al., 2014 and unpublished internal technical reports). Furthermore the tests revealed that for most of the hydroxamate reagents tested, their dosage requirements to achieve recoveries at the same levels was less than that for the phosphoric acid collectors. Recovery of both La and Ce was significantly better for the salicylic hydroxamate and that Nb, Y and Zr recovery were favoured by the octyl and benzoyl hydroxamates (Brian, et al., 2014; Liuyin, et al., 2014). Comparison among the hydroxamate collectors showed that the flotation and recovery performance of cyclohexyl (CHH) and 4-tert-butyl benzoyl (TBH) was not as good as the other hydroxamates for rare earth recovery."

Jan 1, 2015

By Claude Bazin, François Robichaud

"The control of the operation of semi autogeneous grinding (SAG) mills is mainly achieved through adjustments of feed rate, water addition and speed of rotation. With the introduction of image based sensors it is possible to have on-line measurements of the size distribution of the ore feeding a SAG mill. This information could be used for the development of a control strategy to regulate a SAG mill feed size distribution to a set-point. The control of the size distribution is carried out by adjustment of the speed of the ore extractors underneath the ore stockpile. The potential and difficulty associated with the implementation of such control are assessed using a multivariable statistical analysis of data collected from the operation of the grinding circuit of the Agnico-Eagle Goldex mine in Val d’Or, QC. A control strategy for the ore feed size distribution is assessed using a simulator of the ore stockpile operation.INTRODUCTIONThe popularity of autogeneous (FAG) and semi autogeneous (SAG) grinding mills has been increasing over the last 20 years (Napier Munn et al., 1996). These mills use the ore or a combination of ore and steel balls as the grinding media. Since the ore is used as a media for the size reduction the mill ore feed size distribution impacts the performance of the mill. Several papers were recently published on this subject (Dance et al.,2011; Wennen & Murr, 2011; Dance & Valery, 2011; Allaire et al., 2011) showing the advantages of preparing the feed size distribution to maximize the circuit throughput or mill efficiency (Wennen & Murr, 2011; Dance & Valery, 2011; Allaire et al., 2011). With the availability of particle size sensor based on image analysis of the ore on a conveyor (Partanen et al., 2001; Bobo et al. 2004; Edwards et al., 2002; Wei & Craig, 2009) it is possible to control the size distribution of the ore feeding autogeneous or semi autogeneous mills (Partanen et al., 2001).This paper describes a method to control a size distribution index to a set point via the manipulation of the speed of the extractors that withdraw the ore from the stockpile feeding the grinding circuit. The paper consists of 4 sections. The first section describes the considered grinding circuit. A statistical analysis of the collected data on the grinding circuit is presented in the second section. This analysis demonstrates the necessity of using real-time adaptation mechanisms to develop a control strategy for the size distribution of a grinding circuit. The third section describes the method used to simulate the ore stockpile operation and the last section describes the preliminary development and assessment of a control strategy of size distribution of the ore feeding a SAG mill."

Jan 1, 2013

By Elizabeth Wademan

Recessions Eventually End ??Companies aggressively cutting production and inventories ??these will come in-line with demand ??U.S. home inventories are declining ??Housing becoming more affordable ??Global trade recovering after collapsing ??Lower oil prices should act as a stimulus Protracted Deleveraging Process Beginning ??Era of leverage-driven consumption is over ??Greatest destruction of consumer wealth since WWII ??Consumers will no longer be able to substitute capital gains for savings ??Shift towards savings will be a headwind to economic growth ???Paradox of Thrift?

May 1, 2009

By Paul Harvey

Following initial discovery in 1991, BHP Billiton Diamonds Inc opened Canada?s first diamond mine, the Ekati Diamond Mine TM (Ekati) in the Northwest Territories on October 14th, 1998. Four short years later on November 29th, 2002, saw the opening of North America?s first underground diamond mine - the Koala North mine. Nestled between the original Panda open pit and the new Koala pit which is in the early stages of production, Koala North represents the only underground kimberlite mining venture in arctic conditions outside the new underground mines being developed by ALROSA in the Yakutsk region of eastern Russia. Extensive underground kimberlite mining has been practiced in the Republic of South Africa for much of the 20th century and continues today. Underground mining represents a key component of the long term business plan for the Ekati. As various open pits reach their economic limit, continued recovery of high value ore at depth is dependent upon the ability to productively mine the kimberlite pipes by underground methods. As a function of its location, size, and value, the Koala North pipe is ideally positioned to host the first underground mine at Ekati . In addition to being a production source for the operation, Koala North is designed as a learning mine, from which to gain valuable experience in preparation for the potential mining of other larger, higher value pipes by underground methods in the future. Fortuitously Koala North was available for development so the learnings could be integrated into the Panda mine design prior to completion of the Panda pit. Establishing our first underground diamond mine, and applying the open benching mining method in arctic conditions brings a unique combination of mining challenges together in a harsh climate and remote environment. This paper examines the design and establishment of the Koala North mine. Discussion includes experiences gained from the first year of development, production start-up, and provides a brief overview of our potential underground future at Ekati .

May 1, 2003

By Francis Chachula, Niel Erasmus

"In 2002, Titanium Corporation Inc. focused its attention on the development of a process for the recovery of valuable heavy minerals, including zircon and titanium bearing minerals from oil sands froth treatment tailings. The development of a process flowsheet to recover the titanium and zircon minerals from the Athabasca oil sand tailings has evolved through many laboratory, bench and pilot scale iterations.Initial development work focused on so-called ‘beach sand’ material, which is tailings material deposited over a period of time close to the tailings pipe discharge. The derived process flowsheet primarily consisted of gravity concentration stages, which is typical of all mineral sands operations. Titanium Corporation’s business plan calls for the utilization of tailings directly from the tailings pipeline – the process developed around the beach material is therefore risky as it differs from the live tailings in a number of aspects, with the effects on the process unknown. Titanium Corporation successfully obtained an intermediate product through a ‘bulk sampling plant’ coupled directly to an Oil Sands operator’s froth treatment tailings pipeline, during the summer of 2005. Subsequent further processing of this material resulted in poor separation or concentration of the heavy minerals due to a number of reasons. A more effective process flowsheet had to be developed.The newly derived process is basically a marriage between mineral sands technology and oil sands technology that can economically concentrate and recover the heavy minerals and entails the incorporation of a flotation process that takes advantage of the entrained bitumen in the feed to separate the heavy mineral fraction from the quartz gangue This paper will describe the newly derived process as well as the successful results of a subsequent on-site concentrator pilot campaign completed during the 3rd Quarter of 2006."

Jan 1, 2008

By Paul Gauthier

Aujourd?hui, avec un faible prix de l?or sur le marché, les opérateurs miniers doivent revoir leur façon de faire. La méthode de minage «Eureka» permet de réduire les coûts de production et d?accélérer la mise en production des chantiers. Les principales étapes du cycle de minage et les problématiques associées à l?utilisation de cette méthode à la Mine Bousquet y sont décrites.

Oct 1, 2001

By Ronald Molnar

"High demand for metals is driving the exploitation of lower grade and more complex orebodies. These projects are often the initiatives of junior mining companies with limited financial resources. In addition, existing operations seek to enhance revenue from their existing metal recovery operations, through the production of value-added by-product metals and chemicals. Typically, hydrometallurgical circuits, often with novel chemistry, are required to exploit these new ores, to produce the multiplicity of products that will make a marginal project economical, or to increase the product range of an existing operation. Often, the mineral processing engineer is given the task of coordinating the development of a back-end hydrometallurgical flowsheet for their mineral processing project. This paper discusses the objectives that companies have when they commission the operation of a hydrometallurgical pilot plant. The paper goes on to enumerate some of the principal differences between mineral processing and hydrometallurgical pilot plants and the effect these have on the design, operability and potential pilot plant outcomes. Important factors include working with chemically reactive solutions and pulps, elevated temperatures operation, changing rheological properties of slurries, the complexity of integrated circuit flowsheets with long hold-up times and multiple recycle streams, and the need in some cases for extreme attention to purity and cleanliness. Examples will be drawn from the extensive experience base of SGS Minerals Services at the Lakefield site, in piloting both mineral processing and hydrometallurgical process flowsheets.INTRODUCTIONWe are currently experiencing a period of strong growth in the demand for metals. This in turn is turning the spotlight on a great many smaller mining companies and mining promotion ventures trying to tap into the rising metal demand. Some of these companies want to develop their properties and recover metals while others want to develop to the point that a major company will take an interest, or in some cases buy them out completely.With the heightened interest in metals, many orebodies that have been known about for years are being reconsidered for exploitation. Often, the reason they have not been developed to date is because of difficult metallurgy and marginal grades leading to marginal economic viability. In both cases the key that unlocks the resources is often the application of a novel metallurgical flowsheet, often a hydrometallurgical flowsheet."

Jan 1, 2006

By J. E. Terry

This paper outlines the steps that are being taken to close the gap between training and industry and indicates areas in which more work needs to be done. Although based on experience in the Maritime Provinces, it is applicable to industrial and educational studies across the length and breadth of Canada.

Jan 1, 1970

By M. P. Amsden

"Ecstall Mining Limited, a subsidiary of Texas Gulf Incorporated operates the Kidd Creek Mine, a 10,000 tons per day base metal producer, near Timmins, Ontario. Two different ore types are mined and milled: copper-zinc and silver-lead-zinc. At the highly automated Ecstall Concentrator the ores are processed by selective flotation in threes individual circuits. One of the most important metallurgical tools for process control is a sample system incorporating continuous on-stream x-ray analysis. Recently this system was further automated by adding computer control of reagents for two copper-zinc flotation circuits. The computer programs, utilizing optimum seeking methods and smelter contract terms, have increased copper recovery 0.8%, zinc recovery 1.6%, and reduced reagent costs by 12%. Although not anticipated, copper and zinc concentrate grades were improved modestly as well.INTRODUCTIONSEcstall Mining Limited, a wholly owned subsidiary of the Texas Gulf Incorporated operates the Kidd Creek Mine, one of the world's major base metal producers, near the old gold mining centre of Timmins, Ontario. Discovered in 1964, the property was brought into production in November, 1966. Originally designed for 9,000 tons per day, the operation now treats 10,000 tons per day of two different ore types mined from a single open pit. In the near future, open pit ore will be supplemented by ore from an underground operation now being readied for productionAt the Ecstall Concentrator the ores are processed by selective flotation in three individual circuits. The whole plant is highly automated and control is coordinated from a central control room. The treatment process follows conventional practices although fine grinding is required for optimum flotation recoveries. Normally, two circuits treat copper-zinc ore at a combined rate of 6,500 tons per day while the third circuit treats 3,500 tons per day of silver-lead-zinc ore. Special production averages 2,400 tons per day."

Jan 1, 1973

By James Ransford Dankwah

This work investigates the effect of waste plastics addition on the reduction of iron oxide by sawdust. Composite pellets of iron oxide containing sawdust (SD), high density polyethylene (HDPE) and blends of SD/HDPE were fired under argon in a horizontal tube furnace at temperatures between 1300 and 1500 °C. Reduced samples were weighed after 10 minutes of reduction and the extent of reduction was calculated from the measured oxygen contents of the compact. The results showed improved extent of reduction when SD was blended with HDPE. The highest extent of reduction was achieved at SD:HDPE ratio of 2:3.

Jan 1, 2014

By Gordon E. Agar, Brian Lyons, Gregory H. Styles, William B. Kipkie

"Rock rejection during the flotation of a copper-nickel ore was improved by adding carboxymethyl cellulose to both a rougher and cleaner flotation stage. The selection of the rock depressant was based on laboratory rates studies. Plant operating results are presented which confirm the laboratory selection of two particular brands of carboxymethyl cellulose.The rock assay of the concentrate was reduced from more than 40% to less than 15%.IntroductionThe traditional method of selecting flotation reagents relied upon batch bench scale tests, conducted under arbitrary conditions, to identify the effect of the reagent under examination. Too often these were ""one-off"" tests with little or no regard paid to the reproducibility of the results. Sophisticated researchers used statistical methods to design and evaluate the experiments but they were still obliged to rely on the arbitrary and often unreliable batch tests to generate the numbers that were analyzed statistically. An interesting side-effect of the enhanced sophistication of the statistical analysis was often that no significant effects would be uncovered in a series of experiments that would have generated many positive conclusions and much further experimentation if the same results had been evaluated by the traditional method.In the recent past, at least two groups of researchers a have directed their attention to the reliability of the batch experiments with a view toward improving the reproducibility of the test data. In this work the best of the improvements advocated by both of these groups have been adopted in order to generate kinetic data from batch tests that are as reproducible as possible.The objective of the work was to reduce the rock content of a bulk sulphide concentrate produced at Inco's Shebandowan mill. During 1982 the Shebandowan concentrate analyzed 3.5% Cu, 7.4010 Ni, 25% pyrrhotite and more than 40% rock, which resulted in an MgO content of 10.4%. Besides the expense of shipping all of this rock to Sudbury, the rock also contributed to the poor filterability of the concentrate. On favourable occasions the moisture content of the filter cake was slightly over 20% by weight. The magnesia content of the concentrate was deleterious to the reverberatory furnaces used by Inco for smelting nickel concentrate because the slag viscosity increased as the magnesia content increased, and the nickel lost in the slag went up."

Jan 1, 1987