Search Documents

By J Ledgerwood

Namakwa Sands is a mineral processing company based on the West Coast of South Africa and is solely owned by Exxaro Resources Limited. Mineral ore is mined and processed, concentrated and both chemical and mechanically upgraded before being sent for electrostatic and magnetic separation units. The final high value mineral products report as Zircon, Rutile and Ilmenite.The recovery of non-magnetic material is largely dependent upon a number of factors, including but not limited to dew point, ambient temperature, feed rate, mineral size distribution, specific gravity and mineral content in head feed. One important limiting factor to recovery in typical dry mill operations is the particle size distribution of the feed. Variance in the particle size has catastrophic consequences for recovery. This is the reason for this study. Until recently large variances in non-magnetic production were viewed to be a function of machine operation. This view was later rejected with the feed size distribution determined as the major driver of low recoveries, for Namakwa Sands orebody 50 per cent variance in particle size distribution can be noticed within one day. This is because of the successive mining blending techniques employed.The predicament is that the two modes were so closely placed together that recovery of a single mode is almost impossible without the consequence of greatly reducing recovery. The second mode was found at 125 µm while the first was at 90 µm. Interestingly, for the mentioned feed type a cumulative size distribution of a unimodal feed type is almost exactly the same as for a bimodal size distribution. Thus a plot of cumulative size distribution will show no difference due to the modes being so close together. This is the reason why this phenomenon was not noticed before.The study also found that, using an high tension roll (HTR) or rare earth roll, a fine stream with a single mode at 90 µm versus a coarse stream with a single mode at 150 µm would yield completely different results interms of yields. Larger conductive particles are thrown from the roll while small particles loose charge faster (entrainment). Results in terms of the bimodal size distribution show that even though 25 per cent of the feed type is greater than 150 µm the yields followed a similar pattern to that of the coarse particles rather than that of the majority (75 per cent) fine particles. This confirms what was published by M Ziemski and P N Holtham in 2005 on charge decay rates; they mentioned that particle bed effects played a major role in recovery.

Oct 5, 2011

Elastomeric compression gaskets for segmental tunnel liners are capable of fulfilling all sealing requirements for one pass constructed tunnels.Once the segments are mounted and the gaskets are compressed the watertightness of the tunnel is guaranteed at once and for the whole technical life time.The only prerequisite for effective sealing is that tolerances in the tunnel segments be kept within reasonable limits.

Jan 1, 1993

By A Cheatle

GoldcorpÆs Musselwhite mine in north-western Ontario, Canada has in recent years become a world-class deposit. Initially discovered in the early 1960s by Alan and Harold Musselwhite, the then marginal mine eventually started production in 1997 and has to date produced 2.6 Moz of gold. Two million ounces of gold are currently classified as Mineral Reserve and a further 1.2 Moz of gold are classified in the Mineral Resource category for a total gold inventory approaching 6 Moz. Growth of the mineral inventory has been achieved through the successful implementation of strategic planning that sought to extend the mine life through discovery of additional economic zones and increased mined tonnages. Accelerated exploration activity commenced in 2001, at a time when gold price was at its lowest in decades. Focus was placed on building, developing and retaining a highly skilled geological team, maintaining purpose, conducting external reviews and developing a new geological model through research partnerships. Ongoing collaborative research between Lakehead University and Musselwhite mine has seen the development of new structural and geological models through post-graduate and academic studies. Research has included lithogeochemical, stable isotope and structural and metamorphic studies and has led to the evolution of a new mineralisation model (for the mine) and the recognition of brittle and ductile deformation regimes within the mineralised horizons. Exploration drilling continues to provide support for the new geologic model. Gold discoveries have extended known mineralisation 2.3 km along strike from mineral reserves and laterally into parallel zones. The exploration potential to further increase production rates, Mineral Reserves and Resources remains very positive and increases in overall gold inventory are likely. Musselwhite mine has significantly exceeded initial projections for a ten year life-of-mine and a marginal existence.

Jan 1, 2009

By S Natsui, Y Goto, S Kawanishi, J Takahashi, H Nogami

The demand for copper increases yearly, and further improvements in copper smelting efficiency using flash furnaces are required. This study was conducted to understand and promote the interfacial reaction associated with the collision of silica flux and iron oxide particles, ie the formation reaction of fayalite slag, in the reaction shaft of the flash furnace. High-temperature microscopy was used to observe the reaction behaviour of a 2 mm granular SiO2 reagent in contact with micrometreorder- sized FeO reagents in situ. When the amount of FeO was lower than the stoichiometric amount with SiO2, the molten slag formed at the interface between FeO and SiO2 diffused into the SiO2 particle before dissolving the remaining FeO particles. It did not contribute to the subsequent reaction, and despite having the lowest amount of FeO among the samples in this study, many unreacted FeO particles remained on the surface of the samples after testing. On the other hand, under conditions with high FeO content and close to the eutectic composition of the FeO-SiO2 system, a liquid phase formed from low temperatures, gradually increasing in volume and eventually completely dissolving the 2 mm SiO2 grain. These results indicate that the early-stage slag is essential in increasing the interfacial area between FeO and SiO2 and facilitating the supply of FeO to SiO2. In other words, the FeO/SiO2 determines the amount of liquid phase and significantly influences the subsequent interfacial reaction rate between FeO and SiO2. Therefore, the local FeO/SiO2 of the particles falling down the reaction shaft should also be optimised to ensure early slag formation. Meanwhile, the time required for 2 mm SiO2 to complete the reaction for the temperature history employed in this study was significantly longer than the particle residence time in the reaction shaft. Further detailed investigation of the effects of silica flux particle size, composition, and reaction temperature on the reaction time will help find the conditions under which the reaction of silica flux can be completed in the reaction shaft. These kinetic approaches could contribute to future innovations in the copper smelting process using flash furnaces.

Jun 19, 2024

By Y Li, S Ramazan, E Topal

A mine waste dump progression plan can provide a clear outlook of the mining operation. To produce such an output requires detailed placement schedule of the mined material, including the volume (or tonnage) and the allocated dumping location. However, current practise mainly focuses on the ore production, over-simplifying the waste material scheduling. As a result, a rock dump is often treated as a single point in long-term planning, making it difficult to predict the waste dump progression pattern over the life-of-mine. Without such a guidance, it is almost impossible to carry out progressive rehabilitation on the waste rock dumps. The lack of dumping schedule could cause delay in development construction, ie tailing storage facility and run-of-mine pad. Other downstream effect due to the over-simplification is inaccurate estimation of required truck hours, which could have huge financial impact on the operation.In this paper, mixed integer programming (MIP) models of different objective functions, ie maximise truck productivity by minimising the overall haulage distance, minimise required truck deviation between adjacent years, and a hybrid between the two objectives, are utilised to generate the long-term optimum rock placement schedules under the criteria of satisfying site specific conditions. All three MIP models are implemented in a large scale open pit mine. The numerical solutions from the models forms three different rock placement schedules, based on which, the yearly truck requirements are easily calculated and compared. The graphical results show the three corresponding waste dump progression patterns over the life-of-mine, providing the optimised long-term forecast of the operation.CITATION:Li, Y, Topal, E and Ramazan, S, 2014. Optimising the long-term mine waste dump progression and truck hour schedule in a large-scale open pit mine using mixed integer programming, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 335–344 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

In open cut gold mining at Mt Magnet and Reedy, grade control sampling is done with inclined RC drilling using one metre samples. In the small open cuts at Rothsay blasthole sampling was successfully used. Underground sampling for gold and copper grades at Rothsay is done using chip sampling. At the Youanmi open pits both Ditchwitch Earthsawing and RC drilling are used.All assay data are interpreted on sections and plans using a customised SURPAC system. Reconciliations of the grade control predictions of tonnes and grade against initial ore reserves, mining production and milling results are carried out monthly.

Jan 1, 1990

By D P. Blair

Various analysis techniques are used to determine the nature of a large seismic event that was triggered by a mass blast in an underground mine. This event was recorded by surface accelerometer arrays whose output was doubly integrated using a stable filter to determine the dynamic displacements. The peak dynamic displacements during the blast were 0.09 mm, and during its latter stages, this blast induced a seismic event having a peak dynamic displacement more than ten times larger at 1.26 mm. Polarisation analysis, based on the complex covariance matrix, showed that the seismic event was caused by movement of a known underground fault, close to the blast, which radiated most of its release motion as a shear-horizontal (SH) wave. The change in frequency content with time for the blast and seismic event was initially determined using the Fourier-based reassigned S-method. This analysis showed that the large amplitude seismic event had frequency content significantly lower than that of the blast. Nevertheless, this Fourier technique still retains the problems associated with short time windows as well as the fact that most realistic signals are non-stationary. In order to eliminate such influences, the more recently developed empirical mode decomposition (EMD) was used to obtain the intrinsic mode functions (IMF) of the seismic wave propagation. The EMD vibration analysis showed that each IMF generally exhibited distinct frequency changes throughout the blast and a significant reduction in frequency throughout the subsequent event. It is shown that most of the energy of the seismic event is contained in IMF modes 2, 3 and 4 of the SH wave; the high-frequency first mode (IMF1) contains little energy. Such modal analysis is not possible using standard Fourier methods.CITATION:Blair, D P, 2015. Dynamic displacements from a blast-triggered seismic event, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 203–210 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Doyle P, Mulroney D

The Cassidy Shaft was sunk to access the Mount Charlotte and Reward Orebodies below the Flanagan Fault. The 1,184m deep shaft is concrete lined to 6.5m diameter for its full depth. The initial 590m was excavated by stripping into a 1.8m diameter borehole and hoisting the broken material through the existing mine. The remaining 594m was excavated by conventional shaft sinking methods. The shaft was sunk through 3 existing plats and an additional 8 plats cut. 1,800 tonnes of steel and 8 cables were installed during the furnishing of the 4 compartments.

Jan 1, 1985

By R P. Varden

This paper looks at the design of the Bentayga raisebore with subsequent back analysis using a LiDAR survey. A search for LiDAR raisebore assessment publications shows little work has been done on this subject. The paper examines the empirical design and RS2 modelling assessment with the bored condition. The high resolution of the LiDAR enabled mapping of weak structures that were located on the geotechnical investigation hole the orientations of which could not be determined. In addition, the scan showed were water ingress was occurring, potential stress overbreak and structural controls on stability. The LiDAR results were able to confirm no additional support work such as a shotcrete liner is necessary. The LiDAR results have been analysed in one metre increments as volume of overbreak against the empirical stability criteria (McCracken & Stacey 1989). The future use of LiDAR mapping over a range of rock mass conditions will provide quantification of the established empirical assessment improving its reliability. It is also a useful and accurate tool to monitor long term stability of a raisebore due to stress change or ore pass due to wear.

Mar 15, 2021

By T Niitti, J Turunen, P B, A Rinne

In todayÆs marketplace, with high metals prices, many operations are faced with the challenge of improving recovery in the particle size ranges which are normally difficult to recover. This presentation focuses on the various methods used to alter the flow dynamics in a mechanical flotation cell, thereby improving metallurgical results. Modern computational fluid dynamics (CFD) tools have been used in the design phase, with subsequent validation at the plant. Some of the validated variables include mixing profile, power draw and local air hold-up. This presentation underlines how modern CFD analysis can be used to screen and select different approaches before commencing costly trial-and-error experiments at plant scale. Two methods of affecting flow dynamics are discussed û firstly, by altering the geometry of the rotor-stator area and, secondly, by fitting additional features in the tank. The rotor-stator area can be modified to provide more concentrated turbulent kinetic energy or, respectively, to provide more pumping efficiency with less attrition. The tank can be fitted with various additional features, aimed to create different particle suspension profiles. The benefit of both methods is that they can be applied not only to newly installed flotation technology, but also to existing plant cells, thus enabling potential improvement in the mixing profiles, solids suspension, tank sanding and metallurgical performance. Results of several sitesÆ tests are discussed in terms of flow variables measurement as well as metallurgy. This paper demonstrates the effects of different flow dynamics on the mixing profiles and metallurgical results of existing mechanical flotation cells.

Jan 1, 2006

By C K. Boafo, J Visser

Obuasi Mine in Ghana, with more than 100 years of mining history, developed from a surface operation into a deep >2000 m underground gold mine. The challenge is to extract value from narrow veins left after extensive mining in the wider ore zones of the mine. Since the merger of AngloGold and Ashanti Goldfields in 2004 the mine strives to achieve optimum extraction through an integrated Mineral Resource management process from geological modelling, resource evaluation to mine design and scheduling. The shear hosted gold deposit displays complex secondary shears of variable thickness and continuity. There is an ongoing process of changes taking place in the way that geological modelling and resource estimation is done. Recent developments include the use of computerised systems that support the whole resource management chain from resource modelling to reserve optimisation. The change in thought and technology now allows for targeting narrow veins previously ignored in optimisation and mine design since moving into mechanised mining. The increased knowledge and confidence in the resource models now allows for flexibility in mine design, selection of mining method and scheduling and extraction of the reserves. The focus area for change is the way the orebody is evaluated and extraction designed. Since 2005 major changes were made to the process. This paper considers the historical approach of resource management. It looks at the individual process changes and qualifying the way ahead.

Jan 1, 2008

By Richards RG, Cross MS

The development of alluvial mining, processing systems and associated gravity separation technology over the last 30 years is largely linked to the mineral sands industry. Attention has been focussed on Australia in these areas of mineral resource development and technological Advancement.

Jan 1, 1986

By J E. Wheeler, S B. Valine, L G. Albuquerque

It has long been known that closed circuit grinding with a classifier improves grinding efficiency, reduces unit specific power consumption, and reduces over grinding. The classification device removes material from the circuit that has reached the desired size and returns coarse material back to the mill for further grinding. The efficiency of the classifier is an important factor in the overall performance of a grinding circuit. The classifier affects the capacity of the grinding circuit and the metallurgical performance of downstream operations. A review of historical research and modern case studies is used to demonstrate the benefits of high frequency screens for classification in grinding circuits.CITATION:Valine, S B, Wheeler, J E and Albuquerque, L G, 2012. Applications of fine screens in grinding circuits, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 389-394 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By M Berry, F MacCorquodale

The ownership, management and employment structures operating in the Australian minerals industry have dynamically evolved during the last 30 years. One of the most dramatic changes, from an exploration and mining geology perspective, is the reduction of in-house geological expertise and an ever increasing reliance on contract and consulting services.For all companies - big and small - two key issues resulting from these changes are the management of core geological intellectual property (IP) and competitive advantage. This is because there are less experienced geologists at exploration and mine sites, there are fewer head-office technical service teams to support mine sites, exploration teams are smaller with less specialists employed, and there is an ever-greater dependence on contract and consulting services.This paper reviews and explores these issues with an industry-wide geological context, then provides a case study of how Newcrest Mining Limited (Newcrest) has dealt with these issues in exploration. Newcrest has grown from a one-mine company with an Australian exploration focus, to a large global company with multiple operations and an extensive international exploration portfolio. NewcrestÆs management of its geological IP and competitive advantage has evolved as the company has grown and responded to market conditions, including its internal restructuring in mid-2013.CITATION:Berry, M and MacCorquodale, F, 2013. Managing geological intellectual property and competitive advantage - Newcrest Mining LimitedÆs experience, in Proceedings World Gold 2013 , pp 37-44 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

The program, WASTRT 70, was set up specifically to handle the design of tunnel liners and underground structures where inter- action between rock and structure significantly affects the design. It may however be used for any mass/R.C. structure capable of being simulated by straight line elements between modes and with loading restricted to nodes. The analysis system adopts typical elastic/stiffness matrix methods. Two main mass/R.C. design segments are utilized (1) Design of section depth based on maximum required stresses and optimum steel/concrete ratios. (2) Design of reinforcement for a given section depth with concrete stresses given for mass and water code structures. Each design segment covers shear, minimum principal stress on ~ , heavy compression as per code (columns), heavy compression one-face steel (tunnel liners), tension and water code requirements for all moment/thrust/section depth ratios on rectangular sections.

Jan 1, 1976

By Morrell S

As more and more autogenous and semi-autogenous mills are run in closed circuit with cyclones the limitations that can be imposed by poor grate and pulp lifter design are becoming increasingly apparent. Relevant literature on the subject is al

Jan 1, 1997

By Selby DW, Hamill J, Cauley ID, Thomas I, Thornton AJ

The main objective of sulphide flotation in a cassiterite concentrator is to remove sulphide minerals (pyrite, pyrrhotite and sometimes chalcopyrite) from the ore prior to gravity concentration. Tin losses in the sulphide flotation stage account for a significant proportion of the total tin loss. separate studies of the sulphide flotation circuits of Renison Ltd and Cleveland Tin Ltd were conducted to investigate reasons for the tin losses. Sampling surveys were conducted in the rougher-scavenger and also the regrind-cleaner sections of both plants. In both plants, the rougher circuits recover excessive quantities of liberated cassiterite, while recovery of the desired composite cassiterite-sulphide fraction is low. The regrind mills are successful in liberating the composite cassiterite in the rougher concentrate, but at the expense of increasing the proportion of very fine tin mineral. The cleaner circuits recover between 40 and 60% of the cassiterite received, and this is all lost.

Jan 1, 1978

By J Knoblauch, D, P J. J Strobos, C Foggo

The Sally Malay Project is located 120 km north of Halls Creek in the eastern Kimberley region. Since commissioning, ongoing improvements on the plant have resulted in recoveries now greatly exceeding the initial design targets. The continual optimisation endeavours of the Sally Malay metallurgy department included an automation project that was done in close collaboration with Mintek. In this team effort, several problem areas were addressed and the FloatStar advance control system was successfully commissioned to stabilise and optimise the flotation circuit. The remote location of the Kimberley Nickel Mines operation, fly-in, fly-out roster and the current mining boom makes the acquisition of experienced flotation staff difficult. The implementation of an automated flotation control system reduces this burden and contributes to the training of inexperienced staff. This paper illustrates not only the process control improvements achieved as a result of the installation of the FloatStarÖ advanced control system, but also how it has assisted operational personnel with their understanding of the process.

Jan 1, 2006

By J F. C L Costa, J C. Koppe, C Diedrich

Currently mineral resources evaluation is firstly expressed in terms of volume. Next the resources are transformed into tonnes by using an average bulk density applied to the whole deposit or, in some other circumstances, various different densities to distinct geological domains. Previous work in uranium, copper and nickel deposits used linear correlation between grades and bulk density to derive the density. Geophysics methods are also another good way to obtain density indirectly.These approaches do not take into account that two samples with the same grade but with different bulk densities can characterise different sample supports, leading to severe bias in grade and tonne estimates. It is important that the systematic measurements of bulk density are included into the estimation process, particularly when density is not correlated with the grades. Additionally, the extra time and costs involved in obtaining the bulk density data have made the mining industry disregard it.This study reports the impact in resource estimates by using a methodology that includes the bulk density variability. It involves the determination of a variability model for the bulk density and another model for the composite that was weighted by density as well as by its length. Next, these variables are estimated by kriging and the final grade estimates are obtained. The tonnages are obtained with the bulk density estimates. The conventional methodology was also applied and both estimates are compared to the reconciliation data from a major copper deposit. The results show a significant difference between the tonnage and grade estimates obtained from these two methodologies.The results show that considering density variability when compositing leads to a more accurate methodology resulting in better grade and tonnage estimates locally and globally.

Sep 26, 2011

Teleseismic travel time residuals measured on 600-1000 km seismic arrays across the Rio Grande and East African rifts provide evidence for upper mantle low velocity zones beneath each rift of velocity contrast 6%-8%. Refraction studies show thinning of the crust below the rift axes. Regional uplift which extends hundreds of km either side of the axes, is isostatically compensated by negative density contrast at depth. Since the refraction argues against compensation by thickened crust, compensation in the upper mantle low velocity zones is suggested. Temperature effects alone can not explain the reduced velocities. Generation of a few percent of partial melt is the most probable source of the reduction. A passive extensional mechanism is investigated for the Rio Grande rift in which hot asthenosphere intrudes the lithosphere raising its temperature and generating moderate melting. It requires less than 1% extension to explain the melting but a prodigious 26% to raise the temperature from a pre-rifting continental geotherm to the solidus. Geological estimates find that extension is less than 10% over the uplift zone. Such a mechanism is possible only if the prerifting lower lithosphere geotherm lies closer to the solidus than that of stable continent. This is supported by the observed high heat flow in the Rio Grande rift uplift region which, given the long time constant for thermal diffusion, reflects elevated temperatures at depth well in advance of the onset of rifting.

Jan 1, 1987