Search Documents

By Frank Firmstone

When in charge of the Glen don Iron Works, the importance of good methods of filling was forcibly brought to my attention, and it occurred to me that the first step toward the discovery of the best plans was the accumulation of exact information as to the distribution actually effected by various chargers; also, that something could be done in this direction by careful measurements in the furnace, to be afterwards recorded for comparison on drawings. The figures shown herewith have been prepared from such measurements, and nearly all of them refer to Glendon, where the fuel used was anthracite and the ore-mixture about threequarters of New Jersey magnetic ores and one-quarter of brown-ores from the vicinity of the works. Every occasion furnished by the blowing-in of furnaces was utilized, but the data accumulated rather slowly in this way; and, opportunity oEering to make special trials at no great expense, the figures from 2 to 7 were thus obtained. The trials were made by dumping a hopperful (6 barrows) of material at once into the furnace, and, when all the fuel of a round (12 barrows) had been put in, the profile of the upper surface was obtained by stretching a steel tape across the top on a diameter and at a known height. By measuring down from this with a graduated rod, the profile was easily obtained with sufficient accuracy, especial pains being taken to get correctly the crests of the ridges and the bottoms of the hollows, as many intermediate points being included as seemed necessary. This was repeated on another diameter when there was occasion. The same course was followed for the limestone and ore.

Jan 1, 1899

By Charles S. Barrett

THE experiments reported in this paper have been fruitful in disclosing the mechanism of the deformation of iron in compression. They have established the nature of "deformation bands," "etch bands," or "X-bands," that have been a recognized but little understood feature in the structure of cold-worked metals since the early days of metallography, and have shown the role of the bands in the development of preferred orientations by cold-working. The work has also shown the relation of the orientation of individual grains to the preferred orientation of the aggregate. Some of the methods previously used in the determination of the indices of slip planes and slip directions are shown to be untrustworthy in the presence of deformation bands. The conclusion is reached that many slip planes and slip directions must operate during each stage in the compression of a single crystal, and that theories failing to take account of this require revision. In conducting the experiments a method of compression has been used by which extreme reductions can easily be reached, even to the limit set by the metal's capacity to deform without fracture. The work is a portion of a research program on the plastic properties of iron and steel. It is being used as a foundation for studies of orientations resulting from recrystallization and is being extended to other metals and other types of deformation. PREVIOUS WORK The previous experiments are few and have given confusing results. Ono1 compressed a polycrystalline alpha-iron specimen between two flat plates of a testing machine and found that severe deformation oriented the crystals into a duplex preferred orientation, one set of crystallites having a cube diagonal of the body-centered cubic lattice parallel to the compression axis, and another set having a cube axis parallel to the compression axis. We shall speak of this structure as a. double fiber texture of the type [111] + [100]. Wever2 also made an X-ray determination of the texture

Jan 1, 1938

By Joseph Daniels

The Fritz Engineering Laboratory was built under the direction of John Fritz, and presented by him to the University. A view of the building, looking east, is shown in Fig. 1. The building was started in 1909, and completed in 1910, although all of the equipment was not placed until later. Mr. Fritz gave his personal attention to the details of construction and equipment, and it was his custom to drive over every day to the University from his home in Bethlehem and spend some hours watching the work, offering suggestions, making changes, and planning new work. The result is a building and an equipment which embody his practical ideas. The laboratory structure is of the steel mill-building type, of light-colored brick, 91 by 114 ft., of which a section is shown in Fig. 2 and the floor-plan in Fig. 3. The steel frame carries the roof and traveling crane-way. Ample light has been provided by numerous windows in the side and end walls, in the clerestory, and by a skylight 84 ft. long and 9 ft. wide in the north roof. The main aisle of the building is 49 ft. 2 in. between centers of crane-columns, and has a clear height of 40 ft. The remainder of the width is taken up by two side aisles, 18 ft. high. The laboratory consists of four sections: (1) A general testing-section containing the testing-machinery, a small machine shop, and an office; (2) a cement-testing room; (3) a room for making and storing concrete test-specimens; (4) a hydraulic section.

Jan 1, 1912

By Edward B. Durham

The refinery at the San Francisco Mint takes the bullion purchased by the receiving department, and carrying Illore than 200 parts of precious metals in 1,000, or, in mint parlance, over 200 fine, and separates and refines the various metals contained therein, using electrolytic processes exclusively. Bullion containing silver is treated in cells charged with a nitric electrolyte. These cells produce fine silver and leave a residue rich in gold. The residue from the silver-cells, together with crude gold-bullion, is treated in cells having a chloride electrolyte. These produce fine gold and leave a residue containing silver chloride. The latter is reduced to the metallic state with zinc and is then treated in the silver-cells. The various waste solutions and the wash-waters, after being freed from the bulk of their precious metals, still contain copper and other metals. These are removed by scrap-iron, and are then treated in the copper-cells, having a sulphate electrolyte. These cells produce pure copper, and collect a residue containing lead, some gold and silver, and all the metals of the platinum gronp that were in the bullion. This residue is relatively small, and is melted into bars and stored until suEcient accumulates to warrant treating it for platinum, etc. The refinery occupies three large and three small rooms. The large ones are, a melting-room, 30 by 34 ft.; a cell-room, 39 by 46 ft.; and a wash-room, 30 by 33 ft. The small rooms are used as foreman's osce, laboratory, and , re- spectively. The methods here described are those in use in December, 1909, when notes for the present paper were taken.

Jan 1, 1912

By M. A. Whiting, H. Kenyon Burch

One of the advantages presented by electric drive in many classes of work is the ease with which the electric motor can be controlled automatically. In a large number of cases certain features of the control are automatic—for example, the rate of acceleration may be limited automatically or the equipment may be stopped automatically at the limit of travel—but the equipment is started and ordinarily is stopped by hand. In other cases the motion of the machinery is utilized to start, control the speed, and stop the motor automatically, independently of any operator. A considerable proportion of the large mine hoists now in use have certain automatic features, particularly protective devices against overwinding, and, in some classes of electric hoists, devices for preventing excessive acceleration or retardation. The large automatic hoists discussed in this paper, however, are completely automatic, i.e., capable of making their trips without the presence of an operator at the control levers. According to circumstances, various advantages may be obtained . by automatic control, chief of which are decreased power consumption, increased precision and safety of operation, and decreased cost of attendance. The first step in the analysis of a prospective automatic mine hoist is to determine whether automatic operation is feasible at all. If men are to be hoisted, or levels changed, the attention of an operator is required for these purposes; but under some conditions it may be entirely practicable and advantageous to build the equipment so that, while provision is made for hoisting men or changing levels, ore can be hoisted automatically from any one level. If, however, an operator's attention is required every few minutes for changing levels, handling men or drills, or other work requiring hand control, it is obvious that automatic operation between times will not be of any practical benefit.

Jan 1, 1917

THE sessions of the Institute were opened on Tuesday evening, October 26th, at Garrett's Hall, by Mr. Charles A. Otis, Chairman of the Local Committee of Arrangements, who welcomed the Institute to Cleveland, and introduced Col. Charles Whittlesey, who ad¬dressed the Institute briefly on the coal deposits of Ohio. Col. Whittlesey described the situation and character of the coal-beds of the State, and gave a short history of the use of raw coal in the manufacture of pig-iron, and spoke of the excellent quality of metal produced. The aid that a body of scientific miners and metal¬lurgists were capable of giving in the development of coal and other mineral resources was dwelt upon, and the hope expressed that the visit of the Institute to Cleveland might be profitable as, well to its members as to the citizens of the State. The President, Mr. A. L. Holley, responded to the welcome of Mr. Otis and of Col. Whittlesey, and read an introductory address on Some Pressing Needs in the Iron and Steel Manufacture. The following members and associates, duly proposed and indorsed by the Council, were then elected MEMBERS. Alfred S. Bertolet, - Youngstown, Ohio. Henry Binnse, - Chicago, Ill. John Birkinbine, - Philadelphia. Andrew A. Blair, - Watertown Arsenal, Mass. Ogden Bolton, - Canton, Ohio. Lloyd Booth, - Youngstown, Ohio. E. Borda, - Philadelphia. N. P. Bowler, - Cleveland, Ohio. Alexander E. Brown, - Cleveland, Ohio. C. F. Brush, - Cleveland, Ohio. S. M. Carpenter, - Cleveland, Ohio. James Cartwright, - Youngstown, Ohio. Henry Chisbolm, - Cleveland, Ohio. Wilson B. Chisbolm, - Newburgh, Ohio. W. H. Clarke, - Millertown, Pa. James E. Clayton, - Ore Knob, N. C.

Jan 1, 1876

The sessions of the Institute were opened on Tuesday evening, October 26th, at Garrett's Hall, by Mr. Charles A. Otis, Chairman of the Local Committee of Arrangements, who welcomed the Institute to Cleveland, and introduced Col. Charles Whittlesey, who addressed the Institute briefly on the coal deposits of Ohio. Col. Whittlesey described the situation and character of the coalbeds of the State, and gave a short history of the use of raw coal in the manufacture of pig-iron, and spoke of the excellent quality of metal produced. The aid that a body of scientific miners and metallurgists were capable of giving in the development of coal and other mineral resources was dwelt upon, and the hope expressed that the visit of the Institute to Cleveland might be profitable as well to its members as to the citizens of the State. The President, Mr. A. L. Holley, responded to the welcome of Mr. Otis and of Col. Whittlesey, and read an introductory address on Some Pressing Needs in the Iron and Steel Manufacture. The following members and associates, duly proposed and indorsed by the Council, were then elected MEMBERS. Alfred S. Bertolet,.. .. . Youngstown, Ohio. Henry Binnse,. Chicago, Ill. John Birkinbine,.. .. . Philadelphia. Andrew A. Blair,. .. .. Watertown Arsenal, Mass. Ogden Bolton,. .. .. Canton, Ohio. Lloyd Booth,..Youngstown, Ohio. E. Borda,..Philadelphia. N. P. Bowler,.. .. . Cleveland, Ohio. Alexander E. Brown,.... Cleveland, Ohio. C. F. Brush,.. .. .Cleveland, Ohio. S. M. Carpenter,.. .. . Cleveland, Ohio. James Cartwright,.. .. . Youngstown, Ohio. Henry Chisholm,.. .. . Cleveland, Ohio. Wilson B. Chisholm,.. .. . Newburgh, Ohio. W. H. Clarke,.. .. . Millertown, Pa. James E. Clayton,. .. .. Ore Knob, N..C.

By T. Egleston

The necessity of using a refractory material capable of much greater resistance to chemical action and having a far higher melting-point than those which contain silica, which melt and sweat off in the furnace even when not exposed to bases forming with silica more or less fusible compounds, has led to a careful practical study of all those materials which contain very refractory bases. The results of these researches, extending over several years, and made on a very large scale in many of the largest works in Europe, are of the highest interest, not only considered as a step in the progress of the study of the materials themselves, but in the application of refractory materials to metallurgical uses in general. The result of the experience of the last seven years with these basic materials, as in general with all such substanccs, is that natural products cannot be used as such. They are either too uncertain in their quality, contain substances which may in certain cases be very injurious, or, when in a condition in which they might be used, are so rare as to become practically unavailable for employment on a large scale. The materials that may he used are therefore not only limited in number. but they must be prepared artificially. When the use of basic artificial material is further extended, no doubt the number of these substances will not only be greatly increased, but the methods of preparation will be both perfected and cheapened to such an extent as to permit their application in processes for which they have hitherto proved too expensive. The quantity of refractory materials required for making ingots will he from 130 to 150 Ibs. per ton, or between 6 and 8 per cent. of the metal produced. In an establishment producing 2000 to 3000 tons of steel per week, considerable space is required to handle the basic materials properly. It is proposed in this paper to briefly discuss these basic materials and their application in the only two metallurgical processes where they have as yet been applied. These are the basic Bessemer and the basic open-hearth process, known as the Thomas-Gilchrist processes.

Jan 1, 1886

By Robert E. Palmer

The Hawkesworth detachable drill steel shank and bit were invented by A. L. Hawkesworth, while he was a mechanical foreman for the Anaconda Copper Mining Co., at Butte, Mont. Mr. Hawkesworth died on June 16, 1925, at the time that his invention was practically a proved success. The first application for patents was made by him in November, 1918, and the bit is now being manufactured under patents issued in 1922 and 1923. The credit for its development in the early stages belongs to A. L. Hawkesworth, Roy S. Alley, Harry A. Gallwey, E. J. Bowman and various officials of the Anaconda Copper Mining Co. Later improvements, manufacturing problems and the direct usage in the mines were originated and perfected by the mechanical department under C. D. Woodward, E. R. Borcherdt, head of the Rock Drill Equipment Department, Robert E. Kelly of the Mechanical Department, and various operating department heads of the Anaconda Copper Mining Co. The author wishes to acknowledge the assistance of these officials in the preparation of this paper. Comparison of Costs Using Regular Drill Steel and Detachable Drill Steel In 1922 production was satisfactory and sufficient enough to warrant a complete installation in an operating mine. The study and tests were made at the Badger State mine, the production of which averaged 1200 tons of ore per day. E. R. Borcherdt, head of the rock drill equipment department, was in direct charge of the trials, installation, operating problems and records during the entire .period, arid still continues in that position. This mine is a typical Butte mine, operated through a standard four-compartment shaft, served by a double drum hoist and an auxiliary hoist. The texture of the ground and ore has all the variations from soft to very hard granite and sulfide ore with production from levels between the

Jan 1, 1930

By Charles S. Barrett

Metallurgists are making use of the stereographic projection to a steadily increasing extent. In the last five years no less than 20 papers in American metallurgical journals alone have employed the stereographic projection; recent books on physical metallurgy, plastic deformation, X-rays and their applications, and crystal structure use it. Mineralogists have used the stereographic projection for many years in the description of symmetry classes and crystal planes, for it presents an accurate, easily understood plot of any angular relations in crystals with all unessential features eliminated (such as the accidentally determined size and shape of crystal faces). In metallography and physical metallurgy the projection is much used for the analysis of markings appearing on polished grains: slip lines, twins, cracks, structures formed by precipitation, magnetic-powder patterns, etch pits, etc. Data from certain types of X-ray photograms are most conveniently analyzed by its use, particularly those for determining the orientation of single crystals or the preferred orientation of grains in an aggregate. Calculations of how to tilt or cut a crystal parallel to a certain crystallographic plane or to reflect X-rays from a certain plane are rapidly carried out. It has been adopted almost universally to the exclusion of other methods by those studying the deformation of metallic crystals, save where the accuracy required is greater than a few tenths of a degree. Any directional property in a crystal or polycrystalline material can be shown on a stereographic projection; for example, the modulus of elasticity, yield point, etc. It has been repeatedly called to our attention that there is need of an elementary explanation of the principles and methods of stereographic projection, covering all the common applications in the field of metallography and physical metallurgy. The following contribution is an attempt to fill this need. The description of each method is supplemented with references to publications in which the method has been used. For convenience to the reader, these illustrative references are chiefly in American journals, particularly the publications of the American Institute of Mining and

Jan 1, 1937

By T. E. Davidson, C. G. Homan

This report deals with a study of the effects of extreme hydrostatic pressure on a polycrystalline material which exhibits a high degree of elastic anisotropy. Metallographically prepared polycrystalline bismuth samples were subjected to pressure levels up to 20,000 atm in a piston type gas-liquid system. The observed structural changes consisted of deformation localized along the grain boundaries, which appears to be a boundary migration phenomena, and widespread slip and cross slip. Subsequent deformation is progressive with increased pressure, and is substantially different in type from the deformation characteristic of uniaxial compression. A large amount of interest has been shown in recent years in the effects of extreme pressure on metals. In this connection, many investigations into the effects of pressure on physical and mechanical properties and reactions have been undertaken. Due primarily to the experimental difficulties involved, there has not been a great deal of study of the structural changes resulting from exposure of metals to extreme pressure. It has been difficult, for instance, to produce a true hydrostatic stress state in many of the extreme pressure devices used, and also to directly examine specimens metallographically before and after pressurization. The results of a preliminary investigation into one of the effects of extreme pressure, and its associated true hydrostatic stress state, on the structure of metals are discussed herein. Metals exhibit varied degrees of anisotropy in their physical and mechanical properties. Significant among the anisotropic properties is the modulus of elasticity, which varies by a factor of as much as three in some of the fcc metals, and by much larger factors in some of the less symmetrical elements. As a result of the variation of the modulus of elasticity with crystallographic direction, shear stresses will be induced in polycrystalline samples under true hydrostatic compression. Depending on several factors, these shear stresses could become of suffi- cient magnitude to cause localized plastic deformation. Presented herein are some of the structural changes observed in polycrystalline bismuth as a result of exposure to hydrostatic pressures of up to 20,000 atm. Although several other materials in both bicrystal and polycrystalline form are also currently under investigation, bismuth was chosen initially, due to its low symmetry and moderately high degree of anisotropy in the elastic properties. The fact that extreme hydrostatic pressure can induce structural changes in some elements in the polycrystalline state is of importance in itself. However, it may also be a factor in many of the other extreme pressure effects. For instance, this localized plastic deformation could substantially lower the recrystallization temperature, thus altering the effects of extreme pressure on this phenomenon. Also, as commented on by ridgman,' the hysteresis in the polymorphic transition of polycrystalline bismuth under extreme pressures could possibly be attributed to structural changes brought about by unequal compressibility. Therefore, to accurately determine the true effects of extreme pressure on metallic substances, one first must determine if any structural changes due to hydrostatic compression are also simultaneously occurring. The purpose of this work has been to determine whether the shear stresses induced by hydrostatic pressure in an anisotropic polycrystalline material, such as bismuth, could reach a magnitude great enough to cause plastic deformation and to study the resultant structural changes and effects. THEORY In a metallic crystal, the elastic properties are dependent upon the crystallographic direction and plane. Depending upon the degree of anisotropy of the elastic properties and other factors, internal shear stresses of sufficient magnitude to cause localized plastic deformation may be induced in polycrystalline material by true hydrostatic compression. The following highly simplified two-dimensional model of two adjacent grains in a polycrystalline aggregate under hydrostatic pressure serves to schematically demonstrate how these shear stresses arise in an anisotropic material.

Jan 1, 1963

By K. K. Clark, W. H. Somerton

The feasibility of reducing pressures needed to fracture formations by heating the borehole intensively has been investigated on a laboratory scale. Reductions in fracture pressures of heated Bandera, Berea and Boise sandstone cores were observed at various confining pressures, simulating reservoir stress conditions to a depth of 5,000 ft. Both permeable and impermeable borehole boundary conditions were tested. Three heating conditions were used in the tests. One group of samples was heated in a furnace to a temperature of 600C, cooled to room temperature., and then tested for fracture pressures. Two other groups of samples were heated with a borehole heater to maximum borehole wall temperatures of 625 and 792C, then cooled and tested. In all cases, heated samples showed substantial reductions in fracture pressures compared to unheated samples. The higher temperature borehole heated samples showed the greatest reduction, amounting to 70 per cent in the extreme case. In actual application to wells, it was concluded that fracture pressures may be reduced by 20 to 50 per cent by intensive borehole heating before fracturing. INTRODUCTION Hydraulic fracturing of oil and gas wells is an accepted and effective technique for increasing well productivity in many areas, but is notoriously unsuccessful in other areas. The technique becomes less interesting for production stimulation purposes when excessive fracture pressures are necessary. Formations which do fracture but require high pressures, probably form horizontal fractures. There is good evidence to indicate that some formations do not fracture at all, but yield plastically under high pressure. Thus, any technique which will make formations easier to fracture or will reduce fracture pressures is potentially interesting to petroleum producers. Horizontal fractures generally occur in planes of weakness, such as bedding planes, and at pressures equaling or exceeding the effective overburden stress. In the unusual case where planes of weakness do not exist, a slightly higher pressure must be applied to overcome the tensile strength of the rock. In general, high fluid-loss fracturing fluids are conducive to the formation of horizontal fractures.1 Vertical fractures, when they do occur, are initiated at pressures generally lower than overburden pressure and are favored by low fluid-loss fracturing fluids or impermeable boreholes. The pressure necessary to create a vertical fracture in an impermeable, elastic medium can be predicted from the so-called "thick-walled cylinder" equation: Pf = 2 or+ st.............(1) where pf = fracture pressure or = radial stress st = tensile strength of medium. This equation indicates that to fracture it is necessary to overcome a tangential compressive stress, induced by and equal to two times the radial confining stress, plus the tensile strength of the medium. If the above equation held strictly true for rocks, very little could be done to reduce fracture pressure. The tensile strength of the rock might be reduced somewhat, but any change in st would be small compared to the magnitude of the tangential stress at reasonable subsurface depths. Laboratory tests have shown that actual fracture pressures exceed values predicted from Eq. 1 by factors of 1.4 to 28.6.1,2 Eq. 1 thus does not properly describe the

Jan 1, 1966

By G. D. Monk, W. C. Krumbein

The relation between permeability and the size parameters of unconsolidated sand is approached by considering sands as logarithmic frequency distributions having the basic parameters mean size and standard deviation. Sieve separates were mixed in accordance with the normal logarithmic probability law, so that the mean and standard deviation could be varied at will. Experiments were conducted in which one parameter was kept fixed and the other varied; in this manner the dependence of permeability on the individual parameters was evaluated. It was found that permeability can he expressed as the product of a power function of the mean size and an exponential function of the standard deviation. Earlier studies of the effect of size of particles on the permeability of uncon-solidated sand have shown that the permeability varies with the square of some average diameter. This was first pointed out by Hazenl in 1892 and verified by Slichter2 in 1898. Hazen's mean size was defined as the 10 percentile of the cumulative curve (i.e., size that is smaller than 90 pel cent of the distribution and larger than 10 per cent). Slichter's effective size, on the other hand, was found by Wilsey3,4 to agree with the 31 percentile. Fair and Hatch6 found that the geometric mean size of sieve separates yielded the same power function; Hulbert and Feben6 found that the permeability of sieve separates varied as the 1.89 power of the median diameter (i.e., the size associated with the 50 percentile of the cumulative curve). Relatively few studies included the effect of the "sorting" of the sediment on the permeability. It was recognized that the nature of the size distribution, in terms of the spread of the particles about the mean, affects the permeability, but no systematic investigations of this effect are known to the writers. Cloud7 demonstrated that the effect of the grain-size distribution on permeability is definitely measurable. In the present paper the authors investigate this relation analytically, and show that the effects of the size parameters on permeability may be predicted for at least a restricted set of conditions. Properties OF Sediments Recent investigations have shown that essentially all the geologically important characteristics of sediments may be expressed in terms of six measurable quanti-tities possessed by each clastic sedimentary particle. These attributes are: (I) size, (2) shape (sphericity), (3) roundness (angularity) , (4) mineralogical composition (density), (5) surface texture, (6) orientation. Each of these characteristics may be defined in several manners. Size may be expressed in terms of sieve mesh, settling velocity, volume, etc. Sphericity is a shape concept introduced by Wadell;8 it is essentially a measure of the ratio of the surface area of an equivalent sphere to the surface area of the particle. The same

Jan 1, 1943

By G. D. Monk, W. C. Krumbein

The relation between permeability and the size parameters of unconsolidated sand is approached by considering sands as logarithmic frequency distributions having the basic parameters mean size and standard deviation. Sieve separates were mixed in accordance with the normal logarithmic probability law, so that the mean and standard deviation could be varied at will. Experiments were conducted in which one parameter was kept fixed and the other varied; in this manner the dependence of permeability on the individual parameters was evaluated. It was found that permeability can he expressed as the product of a power function of the mean size and an exponential function of the standard deviation. Earlier studies of the effect of size of particles on the permeability of uncon-solidated sand have shown that the permeability varies with the square of some average diameter. This was first pointed out by Hazenl in 1892 and verified by Slichter2 in 1898. Hazen's mean size was defined as the 10 percentile of the cumulative curve (i.e., size that is smaller than 90 pel cent of the distribution and larger than 10 per cent). Slichter's effective size, on the other hand, was found by Wilsey3,4 to agree with the 31 percentile. Fair and Hatch6 found that the geometric mean size of sieve separates yielded the same power function; Hulbert and Feben6 found that the permeability of sieve separates varied as the 1.89 power of the median diameter (i.e., the size associated with the 50 percentile of the cumulative curve). Relatively few studies included the effect of the "sorting" of the sediment on the permeability. It was recognized that the nature of the size distribution, in terms of the spread of the particles about the mean, affects the permeability, but no systematic investigations of this effect are known to the writers. Cloud7 demonstrated that the effect of the grain-size distribution on permeability is definitely measurable. In the present paper the authors investigate this relation analytically, and show that the effects of the size parameters on permeability may be predicted for at least a restricted set of conditions. Properties OF Sediments Recent investigations have shown that essentially all the geologically important characteristics of sediments may be expressed in terms of six measurable quanti-tities possessed by each clastic sedimentary particle. These attributes are: (I) size, (2) shape (sphericity), (3) roundness (angularity) , (4) mineralogical composition (density), (5) surface texture, (6) orientation. Each of these characteristics may be defined in several manners. Size may be expressed in terms of sieve mesh, settling velocity, volume, etc. Sphericity is a shape concept introduced by Wadell;8 it is essentially a measure of the ratio of the surface area of an equivalent sphere to the surface area of the particle. The same

Jan 1, 1943

By David R. Mitchell, E. A. Reilly, G. R. Gardner, F. P. Lasseter

THE methods that may be applied to the treatment of slurries and water, as these are related to practical coal-preparation problems, are concerned essentially with the movements of solids suspended in water. It is assumed that there are no fundamental differences between the principles involved in the treatment of coal slurries and the phenomena encountered in general mineral-dressing practice, and the latter are-presented in some detail. Basic principles are correlated with present practice for both the anthracite and the bituminous coal fields, and methods are discussed which are designed to utilize best all the material subjected to treatment and suggest a sound approach to the solution of problems relating to the return of clear water to process or to streams. In order to approach the practical phases of the subject with sufficient understanding of the basic principles, it is necessary to discuss two types of phenomena that are applicable. The first is flocculation and the second is sedimentation. Descriptive matter is given covering the various methods and types of equipment employed to conduct these operations, with emphasis on their application to water and coal-slurry treatment. DEFINITION OF TERMS Definitions of terms are consistent with modern developments, and conform, in general, with their usage in mineral-dressing practice. Because of variations in coal-preparation methods, it is impossible to define a rigid upper limit of particle size for a coal slurry or sludge which will apply generally. Limits vary somewhat with the particular treatment method employed at a given plant. For purposes of definition, this limit is chosen as the particle size for which preparation methods such as Chance comes and jigs are usually dispensed with, and other methods, such as the Hydro-tator, tables, and froth flotation, are employed. Generally the limit will be 10 to 6 mesh.

Jan 1, 1950

By John H. Holloman

In recent papers, O'Neill,' Vivian, and Zener and Hollomon3 have reviewed some of the information concerning the relations between stress and strain during plastic deformation. Since further information has been obtained since these reviews were published, this paper attempts to further coordinate and amplify the knowledge concerning the plastic deformation of metals in simple tension. Ordinarily the results of tensile tests of metals are presented as graphs in which the load divided by the original area is plotted as a function of the percentage of elongation measured over some specified gauge length. The interpretation of graphs of this sort is limited, since the stress required to deform the metal at any stage of the deformation is actually the load divided by the instantaneous rather than the original area. Furthermore, each increment of the deformation is performed on metal that has been previously deformed, and, as pointed out by Ludwik,4 the strain could be more effectively defined: where e is the strain and AO and A are, respectively, the original and instantaneous areas. The results of the tensile tests can be more effectively presented and interpreted if the stress* (load divided by actual area) is .lotted as a function of the strain as defined above. A schematic curve of this type is presented as Fig. I. In a previous paper,6 the concept of Ludwik7 concerning the flow and fracture of metals was successfully employed to explain some of the puzzling results of notched-bar impact tests of steel. It appears that the use of this concept ii; very fruitful and should be kept in mind in any study of the deformation charactcristics of metals. Ludwik considered that a flow stress-strain curve of a metal was essentially a locus of points that described the stress required for plastic flow of an infinite numbcr of specimens, each with a different strain history determined by the preceding part of the flow curve Each of these specimens can also be considered to have a fracture strength. Uniortunately (or fortunately depending upon the point of view), all the specimens, except the one deformed to the fracture strain, flow and do not fracture. Even though the metals do not fracture, the concept of a fracture-strength curve seems

Jan 1, 1945

By H. G. Moulton

THE INCREASING scale of mining operations over the past decade, particularly in connection with the exploitation of large bodies of comparatively low-grade copper ores, has made necessary the study of the behavior of rock under failure. When extractions of as high as 40,000 tons a day are reached in steam-shovel operations and as high as 20,000 tons per day in underground mining operations, it is evident that excavations soon become of such size that the behavior of the rock will often be dependent on fundamental principles applicable to more or less homogeneous materials under stress, rather than on weathering or local planes of weakness. In the ordinary rock excavations encountered in civil-engineering practice, such as excavations for subways, highways, railroads, etc., rock faces are not carried to depths sufficient to develop any pressures, or consequently any failures, except those due to loose masses resulting from local planes of weakness. When, however, orebodies whose tonnage is measured by hundreds of thousands are to be extracted by steam-shovel operations in open pits, it is necessary to determine if possible in advance the slopes that the sides of the pits will assume, for these slopes influence the shape of the excavations and thereby the amount of ore that may be extracted by the open-pit method. When large orebodies are mined underground at depths of 300 to 500 ft. (91 to 152 m.) by caving methods, the surface subsiding as the ore is withdrawn, it is necessary to determine in advance the outermost limits of fracture in the subsiding surface, for on the delineation of these limits depends the location of surface improvements, mills, smelters, etc. and also the location of development work, such as hoisting shafts, main haulage levels, and all other underground openings that must remain undisturbed during the period of ore extraction. Heretofore, in civil-engineering practice, it has been assumed that earth and rock behave differently in failure. For the calculation of earth

Jan 2, 1920

By Sadao Maruyama

INTRODUCTION Since the big discovery of Kuroko deposits in Kosaka mine, Akita Pref., northeastern Japan in 1959, major Japanese mining companies have been engaged in extensive exploration for the deposits expending large amounts of money. Above all their exploration activities have been particularly fruitful in discovering new deposits in northern Akita Pref. It is estimated that the total ore reserves newly found in the area are at least 50 million tons. Kuroko deposits are the most important ore source of copper, lead and zinc in Japan and have been mined since last century in the said area. Kuroko (black ore) is fine, compact aggregates with sphalerite , glena and barite as principal constituents and chalco- pyrite, pyrite and tetrahedrite as subsequent constituents. The name Kuroko comes from its appearance. It is not rare that total grade of copper, lead and zinc reaches 20 - 30% and the gold and silver content is also fairly good. Accordingly the unit value of the ore is much higher than the ore from other types of deposits. Besides the Kuroko ore, the Kuroko deposits consists of Ohko (yellow ore, massive cupriferous pyritic ore), Keikoh (silicious ore, cupriferous network ore) and gypsum ore. This type of deposit is considered to be not only an important source of base metal but also a source of gypsum and barite. Although the importance of this type of deposit had been commonly recognized, sub-surface nature of the occurrence hampered exploration work. In recent years the improved exploration techniques and increased knowledge of the Kuroko deposits have met with remarkable success in the location of new deposits. This outburst of exploration and dis-

Jan 1, 1970

By William Campbell

The structure of iron and steel, though the object of so much study and research for the past 25 years, is by no means thoroughly understood. In the first place, we have three or more distinct iron-carbon thermal diagrams, each with its own supporters, and each representing a theory of the structure and constitution of cast-iron. In the second place, by reason of the fact that austenite, the solid solution of carbon in iron, decomposes in the solid state into ferrite, or pure iron, and cementite (Fe3C), and that quenching from above this transition-range, no matter how rapid, cannot entirely prevent the change and thus preserve the austenite by itself at ordinary temperatures, it happens that under the microscope we find, in addition to the ferrite, Fe3C, and austenite, which the thermal diagram of steel requires, a series of transition-products with distinctive structures, to which have been given the names martensite, troostite, sorbite, etc. Now these transition-products, in addition to the solid solution, austenite, have been the source of much controversy, at times very bitter. One side would insist that, say, troostite was an entity, which the other side would deny, pointing out that it must be a transition-mixture, with a particular structure. That austenite was a solid solution of carbon in iron has been denied by one school; we have been told that Fe24C dissolved both Fe3C and Fe, and thus gave rise to a whole series of quenching-pro-ducts—all this in spite of the fact that no matter how the thermal diagrams differ in regard to cast-iron, they all agree in regard to the solid solution, austenite, for Fe24C finds no place on the diagram. Thus it happens that while the authorities fight both in regard to the iron carbon diagram and the structures met with in hard-

Jan 1, 1913

By E. T. Turkdogan, P. Grieveson

It is shown experimentally that, by making use of the coupled S-O reaction in ionic melts, it is possible to transfer slclJur or oxygen from a lozv to a high chemical potential through an ionic nzenzbrane. This uphill transfer of sulfur is accompanied by a counter downhill transfer of oxygen and vice versa. The Materials balance shows that the amoulits of sul -fur and oxygen lost or gained by one system are the same as those gained or lost by the other systenz — the two systejns being separated by an iofzic membmne. The systems used in these experi?nents were solid Mn-MnS-Mno and liquid Fe-S-0. Sufficient results were obtained Lo study the kinetics of the transfer and the indications are that the counter diffusion of sulfide and oxide iojzs in the membrane is the rate controlling process. WHEN an ionic oxide-melt reacts with an atmosphere containing sulfur and oxygen-bear ing gases the following reaction occurs: 1/2 S2 (gas) +O2- (melt) = S2- (melt) + 1/2 0, (gas) [1] Under the restrictions that i) electric conductance in the melt is purely ionic and ii) each constituent element in the melt does not change valence, the solution of an atom of sulfur in the melt will result in the evolution of an atom of oxygen, so that the electric neutrality is maintained. For a given temperature and melt composition, the equilibrium concentration of sulfur in the melt is determined by the ratio, po2 /ps2 , in the gas phase and not by the individual partial pressures of oxygen and sulfur. This has been demonstrated by a number of investigators, for example by Richardson and withers', Fincham and Richardson,la by St Pierre and Chipman,' and by Turkdogan and Darken.3 In his Howe Memorial Lecture for 1961, Darken discussed the possibility of uphill pumping of sulfur through an ionic membrane at the expense of oxygen. TO test the validity of this concept associated with coupled reactions, experiments were carried out in the following manner. A presintered mixture of Mn-MnS-MnO and prefused mixture of Fe-S-0, contained in platinum and iridium crucibles, respectively, and separated by a thin layer of soda-glass (to act as an ionic membrane), were placed side by side in an evacuated silica capsule and sealed. This was then kept at 1400°K for a required time to allow Reaction [11 to occur via the ionic membrane. When partial equilibrium is reached, the ratios Po2 /pS2, for systems on either side of the membrane, are equal and the flux of sulfur and oxygen through the membrane becomes zero, although the individual partial pressures po2 andp,, in these two systems may differ considerably.

Jan 1, 1962