Search Documents

By A. W. Schlechten, R. F. Doelling

Parkes' process crusts were vacuum distilled using a shortened Pidgeon retort. Zinc was effectively removed below 800°C and recovered as a zinc sheet easily stripped from the furnace liner. Lead dasdistillationazinc required about 950°C and the resulting lead condensate tillationtended to stick to the thin metal liner. Final purity of residue is limited only by nonvolatile metals such as copper. THE successful commercial application of vacuum distillation for the removal of zinc from lead, as described by W. T. Isbell,' raises the question of whether or not a similar method can be used for other metal separations. Preliminary laboratory experiments on the vacuum distillation of Parkes' crusts by one of the authors' gave such encouraging results that it was decided to make a series of tests with large scale equipment to determine the results that might be expected in plant operation. The pilot-plant test results are reported in this paper. The great advantages of vacuum dezincing are its simplicity, the relatively low temperature of operation, and the fact that the zinc is recovered in the metallic state ready for use again in the desilveriza-tion of lead bullion. These same advantages and others would be realized from the vacuum distillation of the zinc-lead-silver crusts made in the Parkes' process. Zinc readily will distill over at temperatures of 800" to 900 °C as contrasted with the 1200°C or more used in the Faber du Faur furnace. Furthermore, the recovery of zinc as metal is practically perfect since there is no loss by oxidation or fuming. If the vacuum distillation is continued and hastened by raising the temperature to around 1000°C, the lead will distill over at an appreciable rate and deposit in a warmer zone of the condenser. This lead will contain a small amount of silver, but it can be returned to the desilverizing kettles and there is not the chance of loss that there is in disposing of the rich litharge from cupelling. The lower temperatures required will mean a saving of fuel and less wear on the equipment. One further point is that the vacuum distillation could be run on a small scale practically continuously, so as to avoid the accumulation of large amounts of silver-rich material and the need of assembling a large crew for special cupellation runs. It should be pointed out here that the final purity of the silver residue will depend on the copper or iron content of the crusts, as these and other metals with low vapor pressure will not be eliminated. The idea of treating the silver-zinc-lead crusts from the desilverization of lead bullion by vacuum distillation is not a new one, but such experiments have not been reported, as far as can be determined. In 1912, T. Turner presented a paper3 before the Institute of Metals on the vacuum distillation of brass, and a member of the audience suggested that he try his method on Parkes' crusts. In 1935, W. J. Kroll, noted for his discovery of debismuthiz-ing lead by calcium additions, published a paper' on vacuum distillation of metals and pointed out possible applications in the lead industry. Principles of Separation The successful separation of two or more metals by distillation depends upon an appreciable difference in the effective vapor pressures of the metals in the alloy to be treated. The vapor pressures of the common metals have been determined with considerable accuracy; for example, at 800°C the vapor pressures of the individual metals which are of particular interest in this paper are about .as follows: Zn, 241 mm; Pb, 0.0553 mm; and Ag, 0.0000276 mm. Unfortunately,, data are not available on the activities of the components in the ternary system Zn-Pb-Ag, but it can be estimated that on the basis of the vapor pressures of the individual metals a good separation can be made by distillation. The preliminary laboratory tests previously mentioned' supported this assumption. The pilot-plant size vacuum distilling furnace is shown in Fig. 1. It consisted of an abbreviated Pidgeon retort, 5 ft long with an ID of 8 in., heated by six silicon carbide elements placed symmetrically

Jan 1, 1952

Jan 1, 1884

By Joseph E. Pogue

FOR a number of years the petroleum department of The Chase National Bank has been making a continuing study of the financial aspects of thirty oil companies. (See Pogue and Coqueron, "Financial Analysis of Thirty Oil Companies," pamphlet, The Chase National Bank, November 1945, for data covering eleven years, 1934-1944, and the list of the companies making up the group. See also "Capital Employed in the Petroleum Industry," by the same authors, M&M, November 1944.1 This group represents a large sample of theAmerican petroleum industry, covering about two thirds of the business. Certain aspects of this study concern the capital employed in crude oil production, the main features of which arc presented in this paper.

Jan 1, 1946

By F. Keller, A. H. Geisler

Some of the important changes that take place in the structure of aluminum alloys are largely submicroscopic in character. This is especially true of the changes that accompany age-hardening and recrystallization. Although improved metallographic practices have been helpful in indicating some of these changes indirectly, results are limited by the resolving power of optical microscope lenses. The electron microscope, however, provides a new and important means for investigating the fine structure of metals in a range not possible heretofore. It is anticipated that this microscope will yield new and useful information to metallurgists when suitable techniques are developed to utilize its very high resolving power. Several unique methods have been devised to permit the examination of the structure of opaque samples by the electron microscope. These are all based on the principle of producing a very thin film that represents the prepared surface of the opaque metal sample, which can be examined in the transmission microscope; however, the available methods fall into three categories, depending on the manner in which the film is obtained. With the oxide-film method developed by Mahl3-17 a very thin surface layer of the metallographic sample is converted into oxide by a thermal, chemical or anodic treatment. After removal from the metal sample by one of the special techniques described by Evans,19 this oxide film is examined in the electron microscope, and is found to portray the structure of the original metal surface. Films formed on aluminum,8,17 nickel,7 iron 3,8,9 and a nickel-beryllium alloy" by heating; films formed on iron 8.9 by chemical action; and films formed on aluminum3-16 by anodic oxidation, have been examined. The other two are more recent methods developed principally in this country; they consist in making the thin film in the form of a mold or replica of the surface contour of an etched sample. With the negative replica method the thin film is made directly on the sample; with the positive replica method it is made on a negative reproduction of the sample. With both methods, variations in the contour of the metal sample, caused mainly by etching, produce variations in the thickness of the surface replica. Because of the direct dependence of the amount of scattering of the illuminating electrons upon the thickness of the film penetrated, only the variations in thickness of the replica are responsible for tones in the electron image. Negative replicas are made by forming a thin film of some suitable material directly on the polished and etched metal sample, and derive their name from the fact that after removal from the sample they have the high and low points in the sample reversed, as shown in Fig. I. Nega-

Jan 1, 1944

By Robert G. Nisle

In conducting a pressure build-up test on an oil well, it is often necessary to shut-in the well for a short time prior to initiation of the test. The effect of such a short tern shut-in on the resulting pressure build-up curve is derived. The derivation is based on the Kelvin point-source solution and is a straight forward extension of the fundarnental theory. The magnitude of the effect is evaluatecl and illustrated by an example. It is shown that if the production subsequent to the short term shut-in is at least 10 times the duration of the shrct-in, the effect will he less than 10 per cent. INTRODUCTION It often happens that before a pressure build-up test can be made an additional valve must be mounted on the wellhead, or on arrival at the well, it might be learned that the well had been shut-in several hours the previous day because of a shortage of tankage. In such cases the question is How will such an interruption of production affect the results of a pressure buildup test This work explains how to take account of such a short term shut-in in order that the test can proceed without further delay. The solution presented here makes use of the Kelvin point-source solution used by Horne1 in his treatment of the pressure build-up in wells. Use is also made of the super-position theorem. MATHEMATICAL DERIVATION The well is assumed to have been in production at a constant rate for a relatively long time (several days or more). It is then shut-in for a short time, after which it is again placed in production at the previous constant rate. It continues to produce at this rate until shut-in for a pressure build-up test. The Kelvin point-source solution is expressed by Eq. 1. The sequence of production rates is listed in Table I. TABLE 1 — SEQUENCE OF PRODUCTION RATES Time interval Production Rate At time AT the pressure will be the resultant of the sequence of production rates shown in Table 1. An expression for the super-posed effects may be derived from this table. (Effect of + q for T + ? T) + (Effect of - q for T + ?T-t,) + (Effect of + q for T + ? T - t,) + (Effect of - q for ? T) = Resultant........(2) The desired result is obtained by substituting the effect defined by Eq. 1 for the terms in Eq. 2. The result is Eq. 3. When the logarithmic approximation is made for the exponential integrals and the terms collected the result is Eq. 4. Let T — t2 = T = flowing time following short term shut-in t2 — t1 = 6 = duration of short term shut-in Then T - t1 = r + 6 Substitution of these quantities in Eq. 4 gives p(rw ?T) = P,, -When d<<t - AT then d—&apos;-, T— approaches 1. r + AT In this case the effect of the short term shut-in may be ignored. In order to get some idea of the numerical magnitudes involved take the worst possible case, when AT = 0, that is at shut-in. If the error is made less than some maximum acceptable value at this time, it will be less than the maximum for all subsequent times. d + r Let the difference between the value of y-— and 1 be less than 0.1. Then —6+r — 1 < 0.1 S < O.l T Therefore, if the flowing time following a short term shut-in is at least 10 times the duration of the short term shut-in, the error introduced by ignoring the short term shut-in will not exceed 10 per cent of T+AT A T

Jan 1, 1957

THE following employment items are made available to AIME members on a nonprofit basis by the Engineering Societies Personnel Service, Inc., operating in cooperation with the Four Founder Societies. Local offices of the Personnel Service are at 8 W. 40th St., New York 18; 100 Farnsworth Ave., Detroit; 57 Post St., Son Francisco; 84 E. Randolph St., Chicago 1. Applicants should address all mail to the proper key numbers in care of the New York office and include 6c in stomps for forwarding and returning application. The applicant agrees, if placed in a position by means of the Service, to pay the placement fee listed by the Service. AIME members may secure a weekly bulletin of positions available for $3.50 a quarter, $12 a year. MEN AVAILABLE Sales Engineer, 37, seven years experience Europe and Latin America both in underground work and administrative and sales work; speaks fluent Spanish, Portuguese, French. Desires responsible position preferably export in U. S. M-692. Superintendent, 46, married. Experience covers mining and metallurgy as mining engineer and as general superintendent; metallurgy of leaching, flotation, cyanidation; development, construction, operation. Presently available. Prefer U.S.A. M-693-333-E-1-San Francisco. Mine Manager, Superintendent, Consultant, 61, married. Design and erection of mining and mill plants-examinations. Many years as superintendent, manager, consultant, designer and builder of mining plants, flotation mills, concentration mills. Available one month&apos;s notice. Prefer U. S. but foreign acceptable if good climate. M-695-4211-E-9-San Francisco.

Jan 1, 1952

By Bradley Stoughton, M. Miyake

The importance of magnesium alloys as engineering materials has increased rapidly in the past few years. The most important properties of magnesium alloys are their lightness and strength, which result in their extensive use in aircraft and automobile construction. Recent progress in the metallurgy of magneaium seems to offer hope of the production of the pure metal at a reasonable cost. The use of magnesium would doubtless increase greatly if it could be produced at a cost comparable with that of aluminum. A preliminary survey of the magnesium-base alloys shows that the most promising from a practical standpoint are magnesium-aluminum and magnesium-zinc as binary alloys, and magnesium-zinc-aluminum as ternary alloys. The research reported in this paper is a preliminary study of binary magnesium-aluminum and magnesium-zinc alloys, as an introduction to a series of further investigations. Magnesium-aluminum System The magnesium-aluminum system was first studied by Boudouard,1 who merely determined the liquidus. An accepted constitutional diagram was given by Grube,2 who found a compound A13Mg4 (melting point = 462.7" C.) and two eutectics at 35 per cent. magnesium (451.6° C.) and at 68 per cent. magnesium (440" C.) Between the first eutectic and the compound a solid solution exists. This diagram was checked or supplemented by Pécheux,3 Broniewski,4 Eger,5 Schirmeister,6 Voge17

Jan 1, 1926

By A. S. Appleton, M. B. Bever, G. E. Dieter

A gold-silver alloy was deformed by explosive loading at shock pressures up to 510 kbars. The stored energy and hardness increased over the whole range of pressures; the largest rates of increase were observed between 120 and 150 kbars. In this range, markings rkavacteristic of defornation twins first appeared; higher pressures produced markings in all grains. These effects are compared with those of conventional deformation processes and are discussed in relation to probable structural changes. In recent years, increasing efforts have been devoted to the investigation of the effects produced in metals by the passage of high-intensity shock waves of explosive origin. By properly utilizing the energy released by the detonation of a high explosive, it is possible to generate pressure pulses of the order of 500 kbars and higher. (One kbar equals l0 9 dynes per sq cm or approximately 1000 atm.) The passage of a shock wave through a metal occurs at pressures which are very much greater than the yield strength. As the shock front passes a point in the metal, the pressure rises almost instantaneously, and continues to act at the point for a few microseconds. Thus, metals subjected to explosive shock loading experience a nearly instantaneous increase in pressure, and a subsequent release of pressure, which is almost as rapid. Under these conditions mechanical twinning and shear transformations occur readily. smith1 has investigated the metallurgical changes in copper and iron resulting from exposure to explosive shock waves. He found an appreciable increase in hardness in both metals. In copper, a hardness greater than that resulting from 95 pct reduction in thickness by rolling was obtained, yet in the explosive deformation, the thickness of the specimen decreased only a few percent. After explosive loading, the micro-structure of copper showed markings characteristic of mechanical twins. The amount of stored energy resulting from explosive loading is of interest. Measurements of the stored energy of cold work as a function of strain, temperature, strain rate, and composition have been made with gold-silyer alloys deforyed by rolling, orthogonal cutting,3 drilling,4 filing, wire drawing, and torsion. The investigation reported here was also carried out with a gold-silver alloy and its results can be compared with those for the deformation of this alloy by more conventional methods. EXPERIMENTAL PROCEDURES An alloy containing 82.6 wt pct Au and 17.4 pct Ag was purchased in several batches from Handy and Harman Co., New York, as annealed rod 1/4 in. dim. The rod was cold-rolled to a sheet approximately

Jan 1, 1962

By D. W. Breck

Zeolites were first recognized as a new group of minerals by Cronstedt with the discovery of stilbite in 1756. The word zeolite was coined from the two Greek words meaning "to boil" and "a stone" because of the loss of water when heated in the mineralogist&apos;s blowpipe (Breck, 1974). In 1845 it was discovered that certain soils lave the power of retaining ammonium salts Way, 1850). These were the first ion exchange experiments. Later it was discovered that it was the hydrated silicates in the soil that produced this phenomenon. Several years later a paper was published dealing with the action of dilute salt solutions on silicates which showed that this base-exchange principle, which we now call cation exchange, is reversible. The quantitative cation exchange behavior of zeolite minerals, such as chabazite, was studied. As a result any aluminosilicate which exhibited the property of ion exchange was referred to as a "zeolite," even today the term has been applied to clay minerals as well as synthetic organic ion exchange resins.

Jan 1, 1975

By T. R. A. Davey

IN 1947 the author became interested in the fundamental aspects of the desilverizing of lead by zinc, conducted some experimental work, and searched the technical literature for all available fundamental data. Since then a revival of interest in the subject in Europe resulted in the appearance of quite a number of papers. It became evident that it would be more profitable to collect together and examine thoroughly the results of various workers, than to attempt to duplicate the experimental determinations. There are many inconsistencies in the various publications, and it is opportune to review at this time the present status of knowledge on the Ag-Pb-Zn system. There is also a need for a clear description, in fundamental terms, of the various desilverizing procedures. This paper is presented in four sections: 1—There is an historical review of the origins of the Parkes process, of the results of many attempts to find a satisfactory fundamental explanation for the phenomena, and of the modifications proposed to date. 2—A diagram of the Ag-Pb-Zn system is presented. This is believed to be free of obvious inconsistencies or theoretical impossibilities, although thermodynamic analysis subsequently may reveal errors. 3—The fundamental bases of the various desilverizing procedures, which have been used up to the present day, are described; and a new method is suggested for desilverizing a continuous flow of softened bullion in which the bullion is stirred at a low temperature in two stages producing desilverized lead at least as low in silver as that from the Williams continuous process and a crust which, on liquation, yields a very high-silver Ag-Zn alloy. 4—A suggestion is made for the revival of de-golding practice, following a recently published account which does not seem to have attracted the attention it deserves. The terms "eutectic trough" and "peritectic fold" as used in this paper are synonymous with "line of binary eutectic crystallization" and "line of binary peritectic crystallization" as used by Masing.&apos; The German literature on ternary and higher systems is rather extensive and a fairly general system of nomenclature has arisen, whereas in English usage the corresponding terms are not as well established. For this reason the meanings of terms used in this paper, together with the equivalent German terms, are given as follows: 1—Eutectic trough—eutektische rinne: line at which a liquid precipitates two solids S1 and S2 simultaneously. If the composition of a liquid which is cooling reaches this line, it then follows the course of this line until a eutectic point is reached, or until all the liquid is exhausted. The tangent to the eutec-tic trough cuts the line joining S1S2. 2—Peritectic fold—peritektische rinne: line at which a solid S1 and a liquid L transform into another solid S2. If the composition of a liquid which is precipitating S1 reaches the line, on further cooling only S2 is precipitated. The liquid composition moves from one phase region (L + S1) into the other (L + S2), and does not follow the course of the boundary. The tangent to the peritectic fold cuts the line S1S2 produced nearer S,. 3—Liquid miscibility gap, or conjugate solution region—mischungslucke: the region within which two liquid phases coexist in equilibrium over a certain range of temperature. A system whose composition is represented by a point in this region comprises one liquid at high temperature; then as the temperature is progressively reduced, two liquids, one liquid and one solid, one liquid and two solids, and finally three solids. 4—Liquid miscibility gap boundary—begrenzung der flussigen mischungsliicke: the line along which the surface of the miscibility gap dome, considered as a solid model, intersects the surrounding liquidus surfaces. 5—Tie lines—konoden: lines joining points representing the compositions of two liquids, a liquid and a solid, or two solids, in equilibrium. In binary systems the only tie lines customarily drawn are those through invariant points, e.g., through the eutectics of the Pb-Zn and Ag-Pb systems, or the various peritectics of the Ag-Zn system, as in Figs. 1 to 3. In ternary systems it is desirable to draw sufficient tie lines to indicate the slopes of all possible tie lines. 6—Ternary eutectic point—ternares eutektikum: point at which liquid transforms isothermally to three solids, S1, S2, and S Such a point can lie only within the triangle 7—Invariant peritectic (transformation) point— nonvariante peritektische umsetzungspunkt: (a) — On the miscibility gap boundary, the point at which two liquids and two solids react isothermally so that L, + S, + L, + S2. (b)—On the eutectic trough, the point at which a liquid and three solids react iso-thermally so that L + S, + S2 + S3. Such a point must lie on that side of the line joining S,S which is further from S,. (c)—A further possibility, not found in this ternary system, is that the point is at the intersection of two peritectic folds when the reaction concerned is L + S, + S, + S Historical Introduction Karsten discovered in 1842 that silver and gold may be separated from lead by the addition of zinc.2 Ten years later Parkes used this fact to develop the well known desilverizing process which bears his

Jan 1, 1955

By B. V. P. Rao, H. L. Lovell, G. Simkovich

In the study described here, flotation tests were conducted on pure CaF2, on CaF2 doped at several concentration levels with either NaF or YF3, and on natural fluorite samples containing various amounts of impurities in an effort to extend previous knowledge of the influence of crystalline point imperfections on the flotation properties of solids. The results of these tests showed that although recoveries generally decreased as impurities increased, the differences in recovery were not nearly as striking as those detected in earlier experiments. A number of experimentalists have shown an interest in the way in which crystalline point imperfections affect the flotation properties of solids. As long ago as 1953, Welch hypothesized that it might be possible to control surface imperfections and thereby also control the flotation of solids.&apos; A few years later, in some rather extensive work, Plaksin and his coworkers varied the surface imperfections of a number of compounds by oxidation or reduction processes and found that significant variations in flotation properties resulted.2-4 More recently, Simkovich showed that the recovery of both AgCl and PbS could be markedly varied by adding solid-solution impurities, which acted as doping agents, to these compounds.5 Then Mular studied the flotation of ZnO as a function of the doping agents Al2O3 and Li2O.6 Once again, it was found that these impurities, even in very low concentrations, had profound effects upon flotation recoveries. From an imperfection point of view, the defect structures of the compounds tested previously are as follows:7 PbS — amphoteric semiconductor with a Frenkel-type defect structure in the cation sub-lattice.8 AgCl - ionic conductor-Frenkel type defect structure? ZnO — n-type semiconductor, zinc ion interstitials and quasi-free electrons.10 All of these works undoubtedly bear some relation to the findings that the flotation properties of seemingly identical minerals from different ore deposits often exhibit extreme variation in flotation behavior, i.e., that small amounts of analytically undetectable impurities often have a great influence upon flotation

Jan 1, 1969

By Robert G. Woolery, S. Ramachandran, James A. Weber, Donald J. Hansen

Union Carbide began looking seriously at heap leaching in 1971. At that time some 1.6 million tons of mineral averaging 0.40 kg U3O8 /t) (0.80 lb U3O8) were stockpiled at various sites around the Gas Hills, Wyoming, uranium facility. Several alternatives for economically exploiting these reserves were considered and heap leaching seemed the most attractive. At the time, Western Nuclear Inc. was operating a heap leaching project nearby in which the low-grade ore was leached with sulfuric acid, the product liquor treated in an on site solvent extraction circuit, and the stripped product liquor re-acidified and recycled. The operators were most generous in allowing us to visit their site and in answering our questions. They were also helpful in discussing the problems associated with heap leaching. Their experience confirmed our belief that it was possible to operate a heap leach profitably on material too low grade for conventional milling. Based largely on what we had learned from Western Nuclear&apos;s experience, we undertook a program involving a laboratory study to determine the characteristics of the mineral stockpiles, as related to heap leaching, and to conduct a pilot heap leach adjoining our Gas Hill mill. Basically the pilot heap construction and leach procedure were similar to those described in the literature l, 2 with certain modifications to permit detailed monitoring of the operation. In May 1972, the decision was made to construct a test heap. The UCC plant at Gas Hills, Wyoming was selected as the most appropriate site for the following reasons: (1) The necessary equipment for heap construction was readily available. (2) Stockpiles of mineral from the various mining sites were on hand: (3) Construction of the heap could be made on an abandoned tailings pile minimizing problems associated with environmental approval. (4) Proximity of the mill would allow product streams to be absorbed into existing circuits. (5) Necessary utilities were available. (6) Tailings water from the existing circuit could be used for leaching. A program for the pilot heap leach was developed with the following primary objectives. (1) To confirm the data obtained in bench-scale tests particularly on uranium recovery, acid usage, and ore permeability. (2) To evaluate plastic liners used for base preparation. (3) To investigate heap configuration variables. (4) To determine heap leach amenability of the different mineral sources. (5) To establish the economics of heap leaching low-grade ores.

Jan 1, 1979

By A. J. Langhammer

A. J. Langhammer.—That is rather asking a question of the wrong man. However, I will reply to the question from our point of view. There is a considerable amount of iron powder available but the properties vary over a wide range. Powder metallurgy has progressed to the stage where we recognize certain requirements in powdered iron, and what may be a good powdered iron for one application will not necessarily fit the picture for the next one. Further, I believe that there is room for great improvement in the properties of powdered iron. Also, that there is only a limited quantity of powdered iron available having certain specific properties in which we are at the moment interested. F. P. Peters.—May I have a word? With all possible respect to the contributions of the Chrysler Corporation (and they have been tremendous) to the war effort, I think it is easy to get from part of Mr. Langhammer&apos;s discussion a false impression of vaster possibilities than really exist. It would be well if in addition to Mr. Langhammer some other manufacturers of machine parts&apos; might tell us in the next few minutes some of the limitations they have found. For example, what is the maximum tensile strength that is being produced in a commercial part in production today? And what is the actual size limitation on bearings that are in operation and are standing up well? We should always bear in mind the fact—and I think Mr. Langhammer will agree with me— that quoting on a particular part does not necessarily mean placing it in production. In many cases it may be several months before the quotation is resolved and we know whether the part can be made. Let us open up this thing for a little free-for-all discussion of some of the ceilings that do exist in the design of machine parts made by powder metallurgy. The ceiling is not unlimited, and Mr. Langhsmmer will agree with that, 3 am sure. H. Hendriks.*—I do not think that there is so much limitation in the making of powder metallurgic manufactured parts as mentioned. Last year we had the problem of making dies for a special machine used in the manufacturing of slide fasteners. This part was wearing out very fast. It was very hard to make, it had to be hobbed out of a special steel and it was a difficult thing to manufacture in general. The tolerances were one half of one thousandth of one inch on all dimensions. We submitted this die to a manufacturer of powder-metal parts. He thought that it was impossible, but we were not as skeptical as he was and decided to try it anyway. The Canadian General Electric Carboloy Division, in Toronto, gave us then the design for the dies, which we made to their specifications. When the first part was delivered, we submitted it to our Inspection Department and its check showed that all the tolerances were right on the dot. They delivered I9 parts of exact specification, then they went off the beam; they could not keep to the tolerances. It took them a long time to get back again. We do not know what happened, but the main point I want to&apos; make is that if a problem is attacked in the right may, the dies are made right and corrected as to dimensions found out by experiment, I do not think that there is so much diffculty in making powder-metal parts to close tolerances.

Jan 1, 1945

By B. W. Howlett, M. B. Bever, Somnath Misra

The heats oj- formation at 0°C of the compounds AuSn,, AuSn2, AuSn, and the £ phase were measured in a metal -solution calorimeter with liquid tin or a liquid Sn-Bi alloy as solvent. The melting point, heat of fusion, and heat capacities near the melting point of- the compound AuSn in the solid and liquid state were measured in a constant temperature gradient calorimeter. The free energy and entropy of formation of the compound AuSn at its melting point and at 298 °K were calculated from the experimental results and published data. The heats of formation are discussed in relation to the nature of the compounds. The heat capacity below the melting point, heat of fusion, and entropy of fusion of AuSn are interpreted in terms of processes oc-curring before melting. The atomic arrangement in liquid Au-Sn alloys and the bonding in the intermediate phases of. the Au-Sn system are discussed in the light of the measured thermodynamic properties. THE available thermodynamic information on the intermediate phases in the Au-Sn system consists of the heats of formation of the compounds AuSn4, AuSn2, and AuSnly2 and of one composition of the < phase2 besides values of the heat content of the compound AuSn from 0" to 635".&apos; However, the heats of formation refer to different temperatures ringing from 90" to 450°C. Also, the reported error limits of some of the values are large and several inconsistencies are apparent. In the investigation reported here the heats of formation of the compounds AuS-, AuSnz, and AuSn and of three compositions of the < phase were determined for a single reference temperature of 0°C by liquid metal-solution calorimetry. The compound AuSn, which is the only congruently melting intermediate phase in this system, was further investigated in a constant temperature gradient calorimeter by measuring its heat of fusion, melting point, and heat capacity in the solid and liquid states near the melting point. From these data and published free energies of the liquid of composition Au~n,&apos; the free energies of formation of the compound AuSn at the melting point and at 298°K were calculated. The results shed light on the solid-liquid transition of AuSn and on the atomic bonding and state of association of gold and tin in the solid and liquid phases. 1) EXPERIMENTAL PROCEDURES 1.1) Preparation of Samples. Stoichiometric amounts of gold and tin, each 99.99+ pct pure, were melted in evacuated Vycor capsules (12 mm ID). The melts were maintained approximately 150°C above the liquidus for about 12 hr and shaken repeatedly. Samples of the compound AuSn were cooled slowly to room temperature. Melts of the other phases, all of which solidify by peritectic reactions, were transferred to the narrow end (5 mm ID) of the capsule, which was then quenched into iced brine. The solidified samples were annealed in the unopened capsules for 10 days at 30" to 50° C below the respective solidus temperatures. The absence of microsegregation and second phases was confirmed by metallographic examination. At least two batches of each composition were prepared. 1.2) Solution Calorimetry. The heats of formation were determined by liquid metal-solution calorimetry. In this technique, the difference between the heat effects on dissolution in a liquid metal, or alloy bath, of the compound and a mechanical mixture of its annealed components, adjusted for changes in composition of the bath, is the heat of formation of the compound at the temperature from which the samples are added. Details of the equipment and technique have been described."&apos; A tin bath at 300" or 350°C was used with the compounds AuSn,, AuSnz, and AuSn. The high gold content of the £ phase would have caused it to dissolve with an appreciable exothermic heat effect. In order to achieve thermal compensation, the samples were added from 0°C to a bath at 350°C consisting of 66.2 wt pct Bi (99.999+ pct pure), balance Sn (99.99+ pct pure). This solvent gives thermal compensation because gold dissolves exothermically in tin and endothermically in bismuth. The calorimeter was calibrated by adding from 0°C approximately 0.015 g-atom of the solvent.

Jan 1, 1965

Thomas T. Read, New york, N. Y. (communication to the Secretary *):—At the meetings of English technical societies it not infrequently happens that, during the discussion of a paper, someone will arise to say that although he highly appreciated the material presented, nevertheless he believed it would have been better if some other phase of the question had been more highly emphasized. Assuming that this form of discussion is permissible in the Institute, I should like to reiterate the point made by Prof. A. J. Moses that conclusive proof of the identity of the minerals in question is an essential feature of the study of ores in this way. This is also expressed by Paul Krusch in his recent valuable paper on the sulphide ores (in which he arrives at conclusions diametrically opposed to those of Mr. Graton), as follows: "The diagnostic properties of the various ore minerals are known to but a limited circle of investigators." Many earlier investigators began the study of ores beneath the microscope by reflected light, but discontinued their work, in most cases, because they were unwilling to undertake the great amount of preliminary work necessary to securely establish a basis for their inferences. It is evident that Messrs. Graton and Murdoch realize that the promised later paper on diagnostic characters will be the more important of the two, but the point should be emphasized to forestall a flood of literature from other investigators who may gain the impression that the brief survey of polished specimens is a vade mecum to incontrovertible conclusions as to any given ore deposit.

Jan 1, 1914

By Gordon E. Agar

Several correlations have been proposed to relate energy consumption and size reduction in comminution, and although these are arrived at from different starting points, it is postulated that they are all statements of the same basic concept. To test this postulate, the dry ball mill grindability of langbeinite was determined, and the results were analyzed according to the various methods. An examination &apos; of the energy-particle size relationships proposed in the recent past revealed that they had much in common. In fact, the conclusion was tentatively drawn that these expressions were essentially the same, even though they were arrived at from quite different basic premises. The equations attributed to Charles2 and Holmes3 were shown to re- duce to the same single equation, W - A K-3, and the simulated continuous test used by Maxson et al.4 was shown to give the best experimental value of the required empirical parameter, ß. Furthermore, the size distribution parameter a in the Schuhmann equation, y - (x/K)2, was shown to be equal to ß in many cases. The kinetic approach used by Arbiter and Bhrany5 should give the same results as the Maxson test procedure; however, the batch operation used by Arbiter and Bhrany could not produce data that would be as precise as the simulated continuous technique. To test the validity of these conclusions, the simulated continuous method was used to obtain data on the dry grinding of langbeinite. The results are discussed in terms of the various equations and approaches. APPARATUS AND MATERIAL A ball mill with internal dimensions of 17.5 cm (6 7/8 in.) in length by 19.4 cm (7 5/8 in.) in diam was loaded to 50% of its volume with balls 3.2 cm in

Jan 1, 1969

By Douglas Bunting

(Wilkes-Barre Meeting, June, 1911.) WITH the gradual exhaustion of the upper veins in the anthracite coal-fields, the problem of mining at greater depths acquires increasing importance and demands the consideration of a number of important factors, one of which is the greater earth-pressure and the consequent necessity of stronger support o for the roof. Under the pillar-and-chamber system, almost exclusively followed in the Northern anthracite-field, the highest economy in mining is generally secured by leaving, on first mining, pillars only sufficient to support safely the overlying strata. As to the necessary size of such pillars, the opinions of mining experts are widely divergent. In establishing the width of chambers and pillars, the thickness of vein and its depth below the surface have received little consideration. For. instance, it has been quite usual to work both overlying and underlying veins with the same width of chambers and pillars, when the lower vein was two and one-half times as thick, and twice as fits below the surface, as the upper. In view of the generally-accepted theory that the crushing-strength of coal-pillars of the same base-area becomes less with increased height, it is probable, in this instance at least, that the most economical mining has not been secured. This question of adequate pillar-support is economically less important down to about 800 ft. than at greater depths; and it is with reference to mining at these greater depths that the study of the subject here presented has been prompted. The necessity of leaving larger pillars, involving greater mining-costs per ton and also smaller yields per acre, is one of the troubles of deep working. To mine without leaving adequate pillar-supports will result, sooner or later, in a squeeze. Limited areas, it is true, have been mined at certain widths of

Sep 1, 1911

"Mining as an industry of Utah had its inception in the activities of United States soldiers who came to the Salt Lake valley under the command of Gen. P. E. Connor, founder of Fort Douglas, in October, 1862. Many of these soldiers were from California and naturally employed their spare time in the search for minerals. Although their military status did not permit them to make locations in their own names, they assiduously prospected the region in accordance with their own knowledge and with information conveyed to them by Indians and others. Their efforts were encouraged by their commander, who thereby fairly earned the title of father of the industry here, and by their other officers, and many discoveries that subsequently proved of great value were made by the soldiers.No systematic prospecting or mining had been done in the Territory previously, although early Mormon settlers in the southern portion had mined a little ore from time to time in order to provide supplies of lead for bullets. The Mormon leaders at that time did not encourage mining. They held that agriculture was more important and profitable for their followers.Coal was discovered and produced in 1850. Iron was discovered in 1850 and the first iron plant was in operation in 1852 in Iron County. The first non-ferrous metal production was in 1854, in Beaver County, when Isaac Grundy treated ore from the Rollins mine in what is said to have been the first lead furnace west of the Rocky Mountains. The first mineral location was the West Jordan claim in Bingham canyon, located September 17, 1863, now owned by the United States Smelting, Refining & Mining Co., and still productive. The first district organized in the state was the West Mountain (Bingham), December I 7, 1863. Other important districts of early organization are: Little Cottonwood, December 20, 1869; Big Cottonwood, July 11, 1870; American Fork, July 21, 1870; Uintah (Park City), July 8, 1871; Tintic, December 13, 1896; Ophir, August 6, 1870. The first silver-lead smelting was by J. W. Gibson at Stockton in 1866. Lieut. James Finnerty had previously erected two small trial furnaces there, but made no quantity production."

Jan 1, 1925

By Anthony Lucas

THE discovery of oil in 1901 on the Spindletop dome, Texas, inaugurated a new industry on the Gulf Coast, an industry which has grown with the discovery of successive fields, until today it engages the services of thousands of workers and employs enormous capital. New fields are being discovered from time to time and doubtless some still remain to be found, though of late years discoveries have become more infrequent. Nowadays several hundred dry holes are drilled each year in a fruitless and blind effort to discover new fields, for as yet geologic science has developed no effectual method of locating the coastal oil deposits in advance of drilling. Moreover, despite the occasional discovery of new fields, the total production of the Gulf Coast is today no greater than it was in 1906, for the added production of the new fields has been offset by the rapid decline and more or less complete exhaustion of some of the older ones. Careful geologic work within the fields has in some cases increased the production temporarily, but has developed no really new supplies. The Gulf Coast oil industry seems to have passed its period of greatest expansion and to be declining at a fairly steady rate, and this condition is naturally viewed with alarm by the more farsighted operators. In my opinion, the time has come for the adoption of radical and aggressive methods of prospecting, and a fraction of the money wasted yearly in drilling shallow wells in hopeless locations might well be devoted to this purpose. Many facts lead me to believe that all the salt-dome oil has had a common origin; that it has migrated up from considerable

Jan 7, 1918

By G. R. Gohn, S. M. Arnold

The results of stress-corrosion tests upon several non-ferrous sheet metals are presented in this paper. The metals include tough pitch copper, five binary brasses, two leaded brasses, one copper-silicon alloy, two tin bronzes, and two nickel-silver alloys. The tests indicate that for most of these sheet metals, externally applied bending stresses below the yield point (0.01 per cent offset) do not result in stress-corrosion cracking as determined by the A.S.T.M. Tentative Method of Mercurous Nitrate Test for Copper and Copper Alloys (B 154-41T).~ Only in the cases of low brass, high brass and medium leaded brass, all cold-worked 4 B & S numbers hard, was any corrosion cracking observed below the yield strength, and in all cases such failures occurred at stresses above the proportional limit for these materials. However, when some of the same materials which showed no evidence of stress-corrosion cracking at stresses below the yield strength, are stressed beyond the yield point, stress- corrosion cracking is quite apt to occur. Since experience has shown that some of these materials, particularly the brasses, are susceptible to stress-corrosion cracking under service conditions, these tests would indicate that, besides externally applied stress and corrosion, plastic deformation in addition to that resulting from the original cold working of the material is also required to produce conditions conducive to stress- corrosion cracking.

Jan 1, 1945