Search Documents

By CHARLES DORRANGE

INTRODUCTION. CULM is a general term used in the anthracite regions for many years to denote a mixture of coal, bony coal and impurities which is sent to the refuse-banks. Thus, 35 years ago culm contained the pea and buckwheat sizes of anthracite; but to-day, and as mentioned in this paper, culm is used specifically to denote the material which passes through the smallest screen in the anthracite-breaker. The smallest size of commercial anthracite is known as No. 3 buckwheat, barley, or bird's-eye coal, and is ordinarily made through a round-punched plate having openings 3/16 in. in diameter, and over a round-punched plate with opening 3/32 in. or 1/16 in. in diameter. Thus culm will consist of coal, bony coal, slate, gravel, iron pyrite, etc., ranging in size from ? 3/32 in. down to dust. Other local terms for culm are " slush," " silt," and " dirt." The first experiments towards the utilization of anthracite culm by briquetting, and the first briquetting-work done in this country, were in 1872 at Port Richmond Piers, Philadelphia, Pa., by E. F., Loiseau.1 Clay was used as a binder and the finished briquette was water-proofed with shellac, etc. Excessive cost was given as the reason for discontinuing work at this plant. The Delaware k Hudson Co., in 1876, built a plant at Rondout, N. Y., which operated until 1880. Gas-tar was used as a binder, and anthracite screenings were briquetted for engine fuel. Excessive cost, poor results in firing, and the tendency of the fuel to cut the boiler-flues were given as the reasons for discontinuing the manufacture. The next plant was built by E. F. Loiseau about 1878, at Nesquehoning, Pa., near the No. 1 or Nesquehoning colliery

Sep 1, 1911

By Pol Duwez, Spencer R. Baen

A LTHOUGH the practical importance of Fe-Cr--iV Mo alloys has long been recognized, constitution studies have been limited to a few alloys within rather narrow ranges of composition. The purpose of the present study was to establish the phase boundaries in the ternary diagram at a temperature of 1200°F (650°C).* The identification of phases and the determination of phase boundaries were based primarily on X-ray diffraction measurements and occasionally on microscopic observation. The methods used for locating the phase boundaries were essentially those described in detail by Andersen and Jette,' and by others.', The compositions of 180 alloys, prepared by powder metallurgy techniques, are shown in Fig. 1. The chemical analysis and mesh size of the powders which were used for the preparation of the alloys are given in Table I. The powders were mixed for 48 hr or longer, then compacted under 80,000 psi in a %-in. diam steel die. Each specimen weighed approximately 5 g. The compacts were sintered for 4 hr at 2500°F (1371°C) in an atmosphere of pure dry hydrogen (dew point near the temperature of liquid nitrogen). An open tray of chromium powder was placed upstream of the compacts to act as a "getter" for the last traces of oxygen or water vapor. In many cases this chromium powder was bright after sintering. Occasionally the upstream side of the powder was slightly greenish, but in all cases the downstream side was metallic. Some of the alloys contracted during sintering and some expanded as much as 20 pct. The latter alloys, which in all cases were brittle, were crushed in a tool steel mortar, repressed, and resintered for 4 hr at 2500°F. After sintering, the alloys were aged for ten days at 1200°F (650°C) in evacuated (105 mm Hg or better) fused silica tubes and were cooled rapidly to room temperature following the aging treatment. The use of the powder metallurgy technique in preparing alloys for structural investigation offers a simple method 'of avoiding contamination or non-homogeniety which could result from a melting operation. It is very often possible to dispense with chemical analysis of the alloys which have been prepared by the powder metallurgy method. In lieu of chemical analysis, it is necessary to determine the weight of the compact before and after sintering. The chemical composition of the alloy may be considered as that of the green compact, within the limits of accuracy determined by the loss of weight during sintering. In phase-diagram studies it is important to achieve homogeniety in structure, whether the alloys are prepared by powder metallurgy or by melting. Homogeniety means complete diffusion during the sintering of the alloys which are prepared by powder metallurgy. It has been found from experience that the best criterion for establishing the completeness of diffusion is the sharpness of the X-ray diffraction patterns. This criterion has been used throughout the present study. The X-ray diffraction data were obtained using powder cameras of either 214.86 or 71.62 mm diam. Copper, cobalt, or chromium Ka. radiation was used, the choice being based on the alloy composition. The powder samples were obtained by filing or crushing, depending on whether the alloy was ductile or brittle. In some cases, the powder was annealed for 4 to 6 hr at 1200°F in vacuum. The measurements were corrected for film shrinkage and absorption. The large camera, in which the film is mounted

Jan 1, 1952

By David Sinclair, Philip B. Bucky

The dimensions and shapes of mine structures may at present be determined by (1) field experience, (2) structural calculations, and (3) barodynamic tests. § None of these, however, provide information as to the stresses, their direction and distribution in a mine structure. For the design of pillars, the placing of openings relative to working places such as gangways, haulage levels, etc., this information is desirable. Photoelastic methods provide this and, while relatively new, their application in all engineering fields is assuming increasing importance. This paper, therefore, will present the method with a few applications to mining, and with sufficient reference for further study by the reader. PART I The Photoelastic Method The photoelastic method of stress measurement determines the stress distribution in a two-dimensional model by optical means. It makes use of the fact that when a piece of isotropic transparent material, such as glass, celluloid, or Bakelite, is stressed and viewed in polarized** light a picture is seen which indicates by its color bands of light, or fringes, the magnitude of the stresses, their direction and their distribution. General Explanation The stress at any point 0 in a structure (Fig. I), may be resolved into two components, P and Q, each a pure tension or compression, at right angles to each other, called principal stresses.' To fully identify the stress, the values of P and Q and their directions or angle F must be known.

Jan 1, 1940

By David Sinclair, Philip B. Bucky

The dimensions and shapes of mine structures may at present be determined by (1) field experience, (2) structural calculations, and (3) barodynamic tests. § None of these, however, provide information as to the stresses, their direction and distribution in a mine structure. For the design of pillars, the placing of openings relative to working places such as gangways, haulage levels, etc., this information is desirable. Photoelastic methods provide this and, while relatively new, their application in all engineering fields is assuming increasing importance. This paper, therefore, will present the method with a few applications to mining, and with sufficient reference for further study by the reader. PART I The Photoelastic Method The photoelastic method of stress measurement determines the stress distribution in a two-dimensional model by optical means. It makes use of the fact that when a piece of isotropic transparent material, such as glass, celluloid, or Bakelite, is stressed and viewed in polarized** light a picture is seen which indicates by its color bands of light, or fringes, the magnitude of the stresses, their direction and their distribution. General Explanation The stress at any point 0 in a structure (Fig. I), may be resolved into two components, P and Q, each a pure tension or compression, at right angles to each other, called principal stresses.' To fully identify the stress, the values of P and Q and their directions or angle F must be known.

Jan 1, 1940

By G. T. Jackson

The Alaska Gastineau Mining Co.'s mine is located at Perseverance, about 4 mi. east of Juheau, Alaska. Its property consists of a group of claims, the lode system traversing these claims for a distance of 11,000 ft. (3352 m.). It is shown in Fig. 1. The ore deposits occur in what is known as the Juneau gold belt. This gold belt can be traced for about 50 mi. northwest of Juneau and 40 mi. southeast. It consists of a single band, several hundred feet wide, in which stringers and veins of quartz, carrying gold, occur in a slate formation near its contact with some altered volcanic rock known as greenstone. The Perseverance orebody consists of stringer lodes, having a strike northwest and southeast, dipping about 60° to the northeast. These

Jan 1, 1920

By Max W. Ball

THE geologist or mining engineer, whose work takes him into the western United States, whether for the Government or private enterprises, is likely to be called upon to classify public lands as to their mineral character, or to review such classification already made, usually by a Government geologist or mineral inspector. The public-land law covering the matter is clear and logical, and a knowledge of its simpler principles is necessary to intelligent classification work. There are two classes of cases in which a classification of lands as mineral or non-mineral may be required: .first, cases in which lands classified as mineral will be retained by the Government and lands classified as non-mineral alienated; second, cases in which lands classified as mineral will be alienated and lands classified as non-mineral retained.

Jan 1, 1921

By H. E. Kramm

(New York Meeting, February, 1919.) DURING the summer of 1911, I had the opportunity to study in detail the geological conditions of what is known in northern California as " Harrison gulch," in Shasta county. Though the district, as a whole, that is, the western part of Shasta and the eastern part of Trinity county, has contributed during the last 15 years a considerable share of the gold-production credited to Shasta county, very little is known of its geology, perhaps because the country is covered with a dense growth of brush which makes exploration and prospecting extremely difficult. Topographically the district presents a succession of ridges trending approximately N-S.; and alternating with deep narrow canyons. The drainage is partly into . the Sacramento, partly into the Trinity river. Climatic conditions in summer time are almost ideal. It is true, the thermometer may climb to 115°, but the air is dry and the heat is bearable, especially as the nights are always cool. It seldom rains during the summer months, and creeks and springs dry out towards the end of the summer. The winter is severe, lasting from November to April, and usually a thick layer of snow covers the mountains. By reason of the character of its gold-deposits, the region is known to miners as "the pocket country." It contains a series ?of eruptive rocks intruded into slates, cherts, limestones, and conglomerates. Dikes, laccoliths, and batholiths are frequent. In a day's ride it is possible to find all the common igneous rocks from the very acid to the very basic. Serpentines are especially abundant.. The sedimentary rocks are, as rule, broken and shattered as well as folded, and show the effects of intense metamorphism. ? Pocket-hunters " speak of the contact of diabase and slate as the ? pocket-contact." Some rich gold-pockets, however, have also been found in the diabase.

Jul 1, 1912

By Robert K. Linn

The New ldria Mining District is in the southern part of the Diablo mountains of the California Coast Range, 140 miles southeast of San Francisco. The district, noted primarily for quicksilver, also has become important recently as a producer of short-fiber chrysotile asbestos. Between 1853 and 1966, the New Idria district produced 568,092 flasks of quicksilver valued at about $55,600,000, 99 per cent of which was recovered from one deposit, the New Idria mine. In 1944, the district was ranked third in all-time production of North American quicksilver districts, and, since that time, the New Idria mine produced an additional 129,045 flasks, placing the district and the New Idria mine second in all-time production. The major structure of the region is the northwest-trending Coalinga anticline consisting of an asymmetric dome of sedimentary beds ranging in age from Jurassic to Quaternary and marked at its northwest end by an oval body of sheared serpentine 14 miles long by 4 miles wide. The serpentine core, rimmed by Franciscan sandstone of probable Jurassic age, was uplifted in stages between Jurassic and Quaternary time and was intruded along a ring of faults into beds of the Panoche Formation of upper Cretaceous age. The core of serpentine and Franciscan rocks is the locus of about 20 quicksilver mines that rim the faultbounded core and lie within the serpentine mass. The host rock of the most productive deposits is altered Panoche shale and sandstone that lies intermittently along the perimeter of the core. Deposits of the New Idria group of mines and those of a few other small mines lie along the northeast contact in the footwall of the New ldria thrust fault, and a few others occur on steep normal faults around the south and southwest. The chief ore mineral in all quicksilver mines is cinnabar, but minor amounts of metacinnabar and native mercury are found in some of the mines. Ore shoots were deposited in fracture zones and stockworks in altered Panoche shale and sandstone and in definite fissure veins in Franciscan sandstone. Rocks made highly amenable to fracturing by hydrothermal alteration were fractured extensively by late faults. The resulting fracture zones, located along the late faults and at changes in strike or dip of the hanging wall or footwall, are the principal controls of most ore shoots. The largest and richest ore shoots are those of the New Idria mine. The major ore bodies occur in fractured shale and sandstone beneath the New ldria thrust fault at its junction with major tear faults.

Jan 1, 1968

By J. C. Uy, T. E. Davidson, A. P. Lee

The effects of hydrostatic pressures to 26 kbars on the micro structure of poly crystalline Cd, Zn, Bi, Sn, Zr, Mg, Cu, and Fe were examined. Pressure-induced microscopic plastic flow in the form of boundary migration, slip, multiple slip, or twinning has been observed either singly or in combination in cadmium, zinc, bismuth, and tin. No deformation was observed in zirconium, magnesium, copper, and iron. The occurrence of such deformation, in terms of its intensity and initiation pressure, relates directly to the degree of anisotropy in the linear compressibility. Pressure cycling does not significantly affect the residual tensile properties of a zinc alloy which exhibits pressure-induced deformation similar to that of Pure zinc. CLASSICAL elastic theory predicts that a superim-posed hydrostatic pressure will not induce shear stresses in an ideal material. Thus, in the case of homogeneous and isotropic materials plastic flow will not occur as a result of pressure exposure, regardless of the magnitude of the pressure, unless some form of phase transformation or permanent density change takes place. However, real materials, such as metals, often vary considerably from the condition of homogeneity and isotropy. For this reason, Vu and johannin' examined and observed hydrostatic pressure-induced microscopic deformation in polycrystalline cadmium and, zinc, but not in aluminum, to pressures of 9 kbars and indicated that its occurrence is related to anisotropy in the linear compressibility. In addition, Davidson and omaan' have reported pressure-induced deformation in polycrystalline bismuth below the 1-11 transformation pressure. It becomes apparent then that under certain conditions hydrostatic pressure can induce localized internal shear stresses in some metals of sufficient magnitude to cause plastic flow. In this work, eight pure single-phase metals of different lattice structures and degrees of elastic anisotropy were examined after pressure exposures of up to 26 kbars in order to establish the conditions under which such deformation occurs and the type of deformation as a function of pressure. The effects of pressure cycling on the mechanical proper-

Jan 1, 1965

By OWEN H. PERRY

One of man's primary tools is the ordinary screen. Whether of mesh or punched plate, it is fundamental in principle, primitive in its origin, and common in its application through all the world; and yet the screen goes only a part of the way toward the completion of its job of separating materials according to size. It will give a practical and continuous separation according to "size," as generally understood (accurate according to the breadth), but the accurate and continuous separation as to thickness is not a practical function of the screen. Still, all through history, the thickness of particles of material must have been important to many people; therefore, one would expect that some standard method of sizing for thickness would long since have been evolved and that equipment applying that method would be readily available to any in¬dustry. This, however, seems not to be so.

Jan 1, 1949

By Cuppam Dasarathy

The incidence of liquid inzmiscibility in binar)) indium alloys has been theoretically analyzed on the basis of the Hildebrand-Alott equation. Bedictions of miscibility or otherwise Imve in general been found to agree with those phase diagrams that are already publislzed in the literature. Out of a total of 27 systems, where either the complete phase diagrams are published or liquid immiscible behavior is reported, the Predictions agree with the experimental data in 25 systems, the exceptions being the Te-In and Ni-In systems. According to the equation, liquid immiscibility is also indicated in the binary alloys of indium with K, Rb, Cs, Na, Sr, Ba, Ti, Zr, V. Nb(Cb), Ta, W, U, Re, Ru, Rh, Os, and Ir. RECENT investigations by the author have shown that indium when alloyed with iron, chromium, and cobalt shows liquid immiscible behavior.1"3 The Fe-In phase diagram shows a wide range of compositions where the liquids are immiscible.4,5 No intermediate phases are present in this system. No precise information is available about the extent of liquid immiscibility in the Co-In system. However, it is certain that there is a range of compositions where the liquids are immiscible and that there are two or three intermediate phases,376 in the system. Liquid immiscibility is also strongly indicated in the Cr-In system and no evidence was obtained in the brief investigation to indicate the presence of intermediate Cr-In phases.2 The present paper deals with a theoretical analysis of binary alloys of indium with certain elements of the periodic table and indicates the systems where liquid immiscibility may be expected. The incidence of liquid immiscibility in binary systems has been theoretically examined by many workers and many excellent papers are available on the subject. In this paper, the alloy systems are examined on the basis of the more recent ideas proposed by Mott.7,8 It has been claimed8 that the Mott parameter predicts the incidence of miscibility or otherwise with reasonable accuracy and consistency. BACKGROUND TO MOTT&apos;S APPROACH Hildebrand applied his immiscibility rule for non-polar liquids to various alloy systems.9 The basis of this rule is that the equation for the excess free energy of formation of a liquid solution is rather similar to the theoretical expression for the energy of mixing of a regular solution. He postulated that when the heat of mixing is sufficiently high, separation into liquid phases will occur and the condition for complete CUPPAM DASARATHY is at the Research Centre, British Steel Corporation, (South Wales Group), Port Talbot, Glamorgan, Great Britain. Manuscript submitted March 12, 1969. IMD miscibility was shown as where VA and VB were the atomic volumes of the components A and B, and ?EV the energy of vaporization of the component. The term (?EVA/VA)1/2 was regarded as a measure of the binding energy of the component A and was called the L&apos;solubility parameter" 8A. On this basis immiscibility occurs when 1/2(VA+VB)(bA-bBf > 2RT [2] Apparently, however, there were several inconsistencies in that according to Eq. [2] several systems known to be miscible in the liquid state were predicted as immiscible. MOTT&apos;S ANALYSIS ~ott&apos;" regards that the reason for the inconsistencies arising out of Hildebrand&apos;s equation was largely due to the electrochemical attraction between the two elements, not being considered. Hence, Eqs. [I] and [2] were modified by taking into account the electro-negativities of the two elements XA and XB, and Mott arrived at an equation for immiscibility, i(VA + VB)(6A - aB)2 - 23,Q60n(XA - XBf > 2RT [3j which can be written as i **&£*&* >&apos;*°™- &apos;• HI T being the melting point of the more refractory component of the system. In Eq. [4], the numerator was called the Hildebrand term, the denominator, the electronegativity term, and their ratio, the Mott number. Mott observed that if the Mott number of a given binary system was greater than the maximum number of Pauling bonds which the two metals could form, then liquid immiscibility could be expected. The maximum number of bonds formed by a given metal was considered to be directly related to the number of bonding electrons available, i.e., to its maximum valency. Since the valencies of the elements considered vary from 1 to 6, Mott assumed that if the ratio of the Hildebrand term to the electronegativity term was >6, then immiscibility could be expected. On the contrary, if the ratio is <1, the metals should be miscible. Further, the alloying behavior is not only influenced by the valencies of the two elements but also by the relative atomic sizes that influence the types of packing and hence the coordination number. Mott considers that on average the maximum number of near neighbors of unlike atoms is 6. Thus, on both valency and size factor considerations, Mott concludes that the maximum number of bonds&apos; possible in any system was 6, this being the upper limit of the Mott number for miscibility. In considering the alloying behavior of systems with Mott numbers between 1 and 6, Mott plotted the num-

Jan 1, 1970

By Bunting S. Crocker

PEBBLE grinding at Lake Shore is not a temporary wartime substitute. The tube milling plant, with a 1000 ton per day capacity, grinds a hard siliceous ore to 90 pct - 325 mesh. The plant, prior to using pebbles, was consuming 4.3 lb of 1 1/4-in. grinding balls per ton of ore, which amounted to 785 tons of balls per year. At September 1951 prices, $132.60 per ton, this steel cost amounted to, $104,400 per year, or $0.285 per ton milled. By the Lake Shore method of substituting screened rock for this steel, all of this cost is saved. This is one of the major economies in Lake Shore mill practice. Regardless of the ultimate price of grinding balls, a change, back to steel balls is not considered. The present pebble plant is more flexible than a steel ball plant and equally efficient. For example, if it is desired to change the size of grinding media, the pebble charge in any mill can be changed completely in 4 to 5 days, as against 76 days to change completely a 1 1/4-in. steel ball charge. To change pebble size it is necessary only to change two sets-of screens and clean out the rock feed storage bin. This will take 8 to 10 days as against 3 to 4 months to clean. out the customary supply of grinding balls kept on hand. Also it has not always been &apos; possible to purchase all desired sizes of balls at any price. In an analysis of savings effected by the use of the pebble mills, the flexibility of the Lake Shore grinding plant should be discussed, as it has a direct bearing on these savings. The plant has always used several units to handle tonnage rather than sending all the tonnage through a single unit. This principle may result in using small diameter mills, but no objection to that is seen. At no time has any advantage been found in cost per ton ground in large diameter mills. Both the capacity and the power of any mill varies as the diameter raised to the 2.6th power. Consequently large or small mills are equally efficient, and a plant should be designed to use as many units-or combination of units as is consistent with reasonable operating practice. Mills under 5 ft diam are harder to reline, etc. To define the case at Lake Shore, .2600 tons per day formerly were milled in seven 7x6-ft ball mills and twelve 5x16-ft (and two 6x16-ft) tube mills.* This gave an excellent test plant. and an extremely efficient-one. In this plant the ratio of ball mills to tube mills was 1: 2. When the much cheaper pebble mills were substituted for the tube mills, this. ratio -was changed to one ball mill to four pebble mills to take the greatest possible advantage of the cheaper operating mill, i.e., the pebble mill. This flexibility without loss in efficiency has been an important item in the cost savings. It is interesting to note that the use of pebbles for fine grinding was. proved first in the laboratory in a 12-in. ball mill. In fact, since 1934 all testing on -.8 mesh material has been done in this 12-in. mill. Scope of the Tests A paper on fine grinding at Lake Shore Mines was published in July 1940.1 This paper covered 7 years of intensive research on fine grinding as well as sizing methods and equipment, plant scale grinding tests on 5x16-ft tube mills with and without .grate discharges-both with 1 1/4-in. and 3/4-in. balls, the use of laboratory mills to evaluate plant changes, and several reports on classifiers and classification. In the following July the addendum report&apos; was added in which the idea of series-circuit grinding was introduced, and the results of running five stages of tube mills and bowl classifiers were shown. Since 1940, the ball milling end of the plant has been altered extensively as a result of tests on the use of 3 1/2-in. rods in 7x6-ft mills and the use of the Tyler repulping screen with from 7 to 14 mesh screens. These tests are, lengthy and may be covered in a separate &apos;report later. The scope of this report is confined to ore ground by rod milling and ball milling until it passed through an 8 mesh Tyler Ty-rod screen. The -8 mesh screen undersize then was pumped to a primary bowl classifier in open circuit and the sands .from the bowl sent to the primary pebble mills, see Fig: 1. In the pebble mill circuit the ore is ground to 90 pct -325 mesh (24 pct + 28 microns) In studying the flowsheet, attention should be paid to the efficiency of the classification equipment used. The Tyler repulping screen is an efficient machine on the 8 to 10 mesh separation, and the bowl classifier is equally efficient at the 325 mesh separation. Efficient classification is a necessity for series-circuit stage grinding. The ore is hard siliceous porphyry, 60 pct SiO2, 80 pct insoluble. Its grindability at different. meshes has been shown near the top of &apos;the list in F. C. Bond&apos;s grindability tests&apos; Lake Shore is not shown, but an adjacent-mine with identical ore, Wright-Hargreaves, is. Reasons for the-Changeover Since 1936 grinding balls have been rising steadily in price with no sign of stopping. For a mill that used 4.5 to 5.2 lb of grinding balls for every ton of ore ground this rise represented an alarming increase in grinding costs. In many cases the quality of the grinding balls fell off as the scrap steel became more difficult to obtain. The ratio of tube mills to ball mills increased with the use of the Tyler repulping screen in the ball mill circuit. Originally only 3.0 lb of balls per ton were used in the tube mills, and this

Jan 1, 1952

By A. S. Bower

Any process which has for its object the preservation of iron and steel from rust, and which will make these metals more applicable than they now are to the requirements of mankind, will be sure to meet with attention from members of this association, and from all those who are either engaged in the extraction of the ore, its reduction to metal, or the subsequent application of the metal itself. It is, perhaps, not too much to say that when iron and steel are rendered secure against corrosion and decay, they will be used to an indefinitely greater extent than they now are. The whole realm of science has, therefore, been explored in the attempt to discover some method by which the formed article may be preserved, leaving its strength undiminished by the destructive action of rust. Paints, oils, varnishes, glazes, enamels, galvanizing, electro-depositing and what is called "inoxidizing" are among the many systems now in vogue to effect the preservation of iron and steel from the corrosive action of air and water. The object of this paper is to show what may he done in protecting iron and steel from rust by forming upon their surfaces a film of magnetic oxide by an inexpensive process. It is no new thing to be told that magnetic oxide of iron is unaffected by exposure to the atmosphere or to salt water for any length of time. The black sand of Taranaki, in New Zealand, is a sufficiently good example of this. Dr. Percy has pointed out that the reason why Russian sheet iron is less affected by exposure than ordinary sheet iron is because of a coating of magnetic oxide; but this was not known

Jan 1, 1883

By H. De Cizancourt

The Pechelbronn (Alsace) field is the only important French producing field. During 1934, development was carried on as in previous years. The total output of this field reached 553,575 bbl. in 1934, showing a slight decrease from the 1933 figures. Of the total, 315,000 bbl. (56 per cent) was extracted by drilling, while 238,875 bbl. (46 per cent) was obtained by means of shafts and galleries. Exploration of deep Jurassic and Triassic horizons was still in progress at the end of 1934. A deep well reached the Upper Triassic at a depth of 34 m. (2736 ft.). (Information kindly supplied by M. S. Mena, Directeur Technique.) As mentioned before, the small Gabian field (Herault) is gradually being exhausted. No drilling operations were undertaken in 1934, the small production being restricted to the pumping of old wells. Two exploration wells, noted as "drilling" at the end of 1933, were completed in 1934; viz., Lavelanet (Ariége) at 3785 ft. and Santenay (Niévre) at 2578 feet. French Possessions Algeria.—No drilling at Tliouanet. Out of a total of 100 wells drilled in the area, only 8 are still producing. No exploration work is reported during 1934 in Algeria. Tunisia.—Two wells completed; one well drilling at the end of 1934. A total of 11 wells is reported to have been drilled before the beginning of 1935; out of these, 8 were completed before the present program was begun. Morocco.—Exploration work progressed actively last year. The outstanding event was the coming in of Ts. 26 well at 1243 ft. This well took fire, therefore great difficulties were encountered in the accurate measurement of initial production; the figure of 1500 bbl. of oil given here is a near estimate. Oil flowed accompanied by a great amount of water. The apparent decrease of drilling operations in 1934 is explained by the increase in field activities after the results of Ts. 26 were known;

Jan 1, 1935

By G. B. Gould, F. M. Gibson

IN DECEMBER, 1934, the joint Committee on Fuel Values, of the American Institute of Minim and Metallurgical Engineers and the American Society of Mechanical Engineers, submitted a preliminary report, which briefly stated its conclusion that it was not possible to devise any formula for the valuation of coal, based upon the various physical and chemical properties, that would be generally applicable. That report also listed those chemical and physical properties of coal that are generally recognized to have some effect on its use in steam plants, and those physical characteristics of steam plants which affect, in one way or another the relative importance of the properties of coal used in them. Since then, the Committee has considered and discussed in greater detail the interrelationship of the properties of coal and plant characteristics. The conclusions of the Committee are summarized below, with certain recommendations regarding engineering procedure, which will promote the collection of more easily correlated observations with respect to this subject, and thus advance more rapidly the accumulation of data capable of general application.

Jan 1, 1936

By H. J. Struth

The benefits of proration of oil production were perhaps more concretely realized in 1932 than at any time since the oil industry adopted nation-wide production control. Reduced output of crude petroleum, which brought the daily average of the United States down to approximately 2,000,000 bbl. from a peak in 1931 of more than 2,600,000, had a telling effect on the trend of oil prices. Mid-Continent crude was advanced in price from 776, for 36-gravity oil, to $1.04 a barrel. California crude, of 26-gravity at Signal Hill, moved forward from 736 to 976 a barrel. Pennsylvania crude, the only exception to the upward trend, rose in price from $1.82 per barrel to $2.02, only to react to $1.72. This was due to local conditions which necessitated an adjustment to overcome competition from other areas of the United States. East Texas continued to exert a far-reaching influence on the crude and gasoline market during 1932. Despite the fact that oil prices were advanced in most fields, large quantities of oil were produced in East Texas in violation of state proration orders, and sold in the market at prices considerably below official postings. This created competitive conditions in the gasoline market that were felt by all refining centers of the United States. The quantity of gasoline produced from cheap East Texas crude was not large, but the volume was sufficient to influence prices in practically all sections of the country. Thus, while the industry&apos;s&apos; economic situation showed visible improvement statistically, the unreported and unseen statistics originating in East Texas proved to be an insurmountable obstacle to the economic betterment that was otherwise apparently justified. Somewhat surprising to many was the fact that gasoline consumption was maintained within 10 per cent of the preceding year. Domestic consumption showed only a net decline under 1931 of about 8.5 per cent; exports dropped in volume to the extent of about 23 per cent. As a matter of fact, domestic gasoline consumption was only about 1.4 per cent less than it was in the predepression year of 1929. Exports, however,

Jan 1, 1933

By Richard W. Smith

Why are we losing our liberties? (1) . . . because our local chambers of commerce come to the National Chamber&apos;s annual meeting, vote for a policy on federal economy, and then go to Capitol Hill and ask for a federal project for their area. (2) ... because our mining men ask for a subsidy to mine submarginal deposits that can&apos;t be economically mined in a free economy. (3) . . . because 18,000 men and organizations all over the country recently wired or wrote a Congressional committee asking that the Army Engineers be exempt from the President&apos;s power to reorganize the Executive Branch of the government under the recommendations of the Hoover Commission.

Jan 1, 1949

By Arnold S. Epstein

Tlze green electroluminescence occurring at liquid-nitvogen temperature in epitaxial gallium phosphide diodes is exarnined using the donor dopants silicon and sulfur. Zinc is used as the p-type diffusant. Two tt~ain peaks are found, namely til 0.56 and 0.535 p. The intensity of the gYeen peak occurring at 0.56 is found to oary as -4"&apos; wlzere Jf is the forward current density and to first order appears to be dependent on the concet~tvation of ionized donovs. Tile vadintive lifetinze fov this process is -10-&apos;sec. The intensity of the 0.56-p lu~ninescence is nt least several ovdevs of magnitude greate,, at liquid-nitvogen temperature than that noted jor the 0.538 radiation for current densities up to about 35 amp per sq cm. The variation oj- the intensity of. the 0.538-p peak with current density caries according to the donor dopant. With sulfur as the donor one has a J12 dependence, whereas when silicon is the donov a J1.5 dependence is noted. Tl~e above can be fitted to a In molecular process (in first order) such as a band to band recombination. The constant B fir band to band vecombination) is found from our experitt~etlt to be of the order of 2 CZI cm per sec, zcl~ereas for tlze impurity vecombination peak (0.56 p]) tile A cotzstor~t is of the order of. 7 x 10-&apos; cu cm per sec. The structuve o/. the diodes at liquid-nitvog-en tett~peruture is oj tlze double injection type, and by carefi~lly selecting. the thickness of the structure one can regulate the onset of the 0.538-p radiation. The diode clzavaclevistics follow an I-Vx laiv where x is >1. Llregatiue resistance in these structures con be correlated with saturation of tlze 0.56- peak. ThE development of high-purity, large single crystals of epitaxially grown gallium phosphide is the ultimate aim of the studies to be reported. While a number of papers and reviews&apos; have been presented on properties of gallium phosphide grown from gallium solution and from the melt, less attention has been paid to the properties of epitaxial gallium phosphide grown from the vapor. In the studies to be reported we have examined the effects of shallow donor impurities, primarily silicon and sulfur, at liquid-nitrogen temperature, on both the electrical and green electroluminescent properties of carefully characterized single-crystal epitaxial Gap. I) EXPERIMENTAL PROCEDURES A) Material Preparation and Properties. The samules used in this investigation were single-crystal n-type epitaxial gallium phosphide. he single crystals were synthesized from the elements by vapor transport and epitaxial deposition on single-crystal gallium arsenide substrates. Typical transport agents used were chlorides. The growth procedures are described in more detail in Ref. 2. The samples were grown in the (111) orientation and had thicknesses up to 480 . Following the growth, the GaAs substrate was removed from the epitaxial Gap by etching in nitric acid. The Hall effect and resistivity of these n-type samples were measured as a function of temperature and analyzed for impurity content and compared with spectroscopic emission analysis. The results are given in greater detail in Ref. 3 but a summary is noted in Table I. In Table I, AED denotes the donor ionization energy, Nd is the donor impurity concentration, lvA is the acceptor impurity concentration, NI is the total impurity concentration, Rip vs temperature is the measured Hall mobility-temperature relationship from liquid nitrogen to about 400"K, n(77"K) is the measured carrier concentration at liquid nitrogen, and R/p(77&apos;~) is the measured Hall mobility at liquid nitrogen. Good agreement is noted between electrical and emission analysis for the major donor impurity, silicon, in the two materials where it is a major constituent. In the case of the two samples SC90-6 and AP138-3(111) B which were sulfur-doped the ionization energy found from the electrical data is in good agreement with that reported for sulfur.4 The acceptor impurities are not known, although from the presence of magnesium in the samples as indicated by emission analysis and its known role as an acceptor in GaP,4 magnesium could be present as an acceptor. Similarly, since silicon is known to be an amphoteric impurity4 it may also be present as an acceptor in the Gap.* The *A small band has been noted at 0.625 11 in samples SC90-6, SC76-4, and SC77-4, suggesting according to Ref. 5 that sillcon could be present as an acceptor In these samples since these authors have found this peak to represent a donor-silicon emission. presence of calcium deduced from emission analysis is not correlatable with the electrical analysis and its presence as an electrically active impurity should be questioned. B) Sample Preparation and Diode Fabrication. The original slices were of the order of 2 sq cm in area witi the (111)B face up. The material was cleaved and sectioned and the best pieces selected (i.e., those which visually appeared to have the least strain and defects). The samples were polished, lightly etched, and cleaned in trichloroethylene. Zinc was diffused in a closed tube at 800°C to form a p-n junction. Diodes were made from these samples. The depth of junction varied, but did not exceed 10 p depth. The back side of the slice was lapped back and a low-resistance n-type contact was formed (at 600°C in forming gas) to an Au-Mo tab with a hole in the middle for

Jan 1, 1968

By Henry Newton

It may seem somewhat a work of supererogation to present to the American Institute of Mining Engineers, composed largely of gentlemen with whom the subject is so familiar, a paper on iron ores and their distribution. To many of them, however, it possibly will not be without interest, as there may be some, like myself, who hare nowhere found a connected account of the character of the deposits and the circumstances upon which are founded the great iron-producing centres of the world. This blank I have endeavored to fill,

By Henry Newton

IT may seem somewhat a work of supererogation to present to the American Institute of Mining Engineers, composed largely of gentle- men with whom the subject is so familiar, a paper on iron ores and their distribution. To many of them, however, it possibly will not be without interest, as there may be some, like myself, who hare nowhere found a connected account of the character of the deposits and the circumstances upon which are founded the great iron-producing centres of the world. This blank I have endeavored to fill,

Jan 1, 1875