Search Documents

By Bradley Stoughton

(Cleveland Meeting, October, 1912.) [SECRETARY'S NOTE.-To avoid repetition of foot-notes, references to authorities are made in this paper by means of figures, referring to a numbered list in the appendix.-J. S.] INTRODUCTION. THIS paper gives the results : first, of a research into the somewhat extensive literature of titanium; and second, of a series of original tests upon the effect of titanium on iron castings. New investigations have also been made upon the effect of titanium on steel, but I hope to treat this subject in an independent paper at some later date, and, therefore, will not discuss the experiments in detail here. The combined results of this study, which extended over a period of more than two years, can be briefly summarized as follows: 1. Steel or cast-iron, in which the titanium is properly proportioned, and which has been properly treated, is improved in strength, toughness, and durability against wear, such as, for example, the wear of railroad-rails, of steel and chilled-iron .rolls, car-wheels, etc. 2. These improvements seem to be caused, not so much by the direct effect of titanium on the metal, as by its cleansing influence in removing harmful impurities, such as oxygen and oxides, nitrogen, occluded slags, and perhaps also sulphur. It appears also to reduce segregation, which would contribute to the same end. 3. In order that its effects may be fully realized, the treatment of steel or iron with titanium must be correctly performed. There are a few simple, but essential, details to be observed; if they are neglected, the best results cannot be expected. To illustrate by an example : A series of tests on cast iron

Nov 1, 1912

This report presents information developed during Bureau of Mines contract H0242016, "Mine Shaft Fire and Smoke Protection Systems" from May, 1974 through June, 1975. Purpose of the metal and nonmetal health and safety project was to evaluate mine shaft fire and smoke hazard problems, and to develop and demonstrate a low-cost, reliable mine shaft fire protection system that would protect against such hazards and would be applicable to a majority of metal and nonmetal mine shafts, including raises and winzes, especially in deep mines. Program effort proceeded through five phases, culminating in the successful in-mine fire demonstration of a prototype system. In addition to this final report, a film is available which depicts components of the system and its successful shaft fire testing at an underground mine.

Jan 1, 1975

By Shemek Oginski, MARK C. JOHNSON

All Rights Reserved. Printed in the United States of America. Information contained in this work has been obtained by SME, Inc. from sources believed to be reliable. However, neither SME nor its authors guarantee the accuracy or completeness of any information published herein, and neither SME nor its authors shall be responsible for any errors, omissions, or damages arising out of use of this information. This work is published with the understanding that SME and its authors are supplying information but are not attempting to render engineering or other professional services. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of the publisher. Any statement or views presented here are those of individual authors and are not necessarily those of the SME. The mention of trade names for commercial products does not imply the approval or endorsement of SME.

Dec 1, 2015

This paper discusses the social and economic impact of mining, and in particular goldmining, on New Zealand. The range of topics covered and their complexity has confined us in this paper to highlighting the main points of concern û a detailed report is under preparation. A major problem in undertaking this study was the lack of hard data on important environmental, economic and social issues and if there is to be effective planning in the area of natural resource use this situation must be rectified. The following conclusions were drawn: Goldmining was very important in shaping New Zealand's early social and economic development, providing wealth, employment and impetus for social change.Foreign investment and technology has been an essential element in New ZealandÆs economic development.Mining is a small industry at present by this must not be allowed to obscure its potential to broaden New Zealand's economic base and provide foreign exchange.With modern methods, development of mineral resources and environmental protection are not incompatible but certain unique and irreplaceable areas must be preserved.There are problems in evaluating mining and other projects because different groups hold different values, and arguments often hinge on the valuation of costs and benefits rather than the technical aspects of the analysis.Mineral exploration is a high risk business and the potential returns must be sufficient to attract capital if New Zealand's mineral resources are to be developed.A resurgence of goldmining will clearly have obvious benefits for Waihi but the local community must plan carefully for their future. New Zealand will also gain valuable foreign exchange required for higher levels of economic activity.

Jan 1, 1981

In October, the Aluminum Company of America restarted the fourth of seven pot-lines at its Point Comfort, Tex. primary aluminum smelter. The price of primary aluminum ingot, as quoted by American Metal Market, was increased from a range of 60.5 to 63.0 cents per pound at the end of September to a range of 66.0 to 66.5 cents per pound at the end of October. BERYLLIUM On October 15, Brush Wellman, Inc., of Cleveland, one of two U.S. producers of primary beryllium products, announced a planned $6 million expansion of its extraction plant at Delta, Utah, increasing the plant?s capacity to extract beryllium from bertrandite ore by 25%. Another $5 million will be spent on two mine expansion programs in Jaub and Millard Counties, Utah. Other mineral claims and 1 eases he 1 d by The Anaconda Company will be taken over by Brush Wellman through lease or purchase. This expansion, when completed in 1981, will decrease U.S. dependence on imported beryl ore.

Jan 1, 1979

One of the critical challenges facing the mining industry ? and not just in the United States ? is the looming labor shortage. A significant percentage of the industry?s professional workforce is, well, getting old, and many will be retiring in the next 10 years or so. This is not a new issue to the industry. It has been discussed at various industry meetings and conferences for many years. How does mining, with its largely negative public image, attract young people to mining schools? And, equally important, who is going to teach them? Mining schools, what?s left of them in the United States, are beginning to lose qualified faculty to retirements, and no one is available to replace them. SME addressed this issue during the keynote session at its annual meeting in February in Denver, CO. This year?s theme was ?Mining: It?s About the People.? Despite a blizzard that blanketed the city on the day most attendees were to have arrived, the meeting still attracted a record 7,202 people. And the accompanying exhibit sold 822 booths, also a record. The U.S. Department of Energy?s National Energy Technology Laboratory contracted with the National Academies? National Research Council to complete a study concerning the availability of skilled workers to meet the energy and mineral security requirements for the United States. The National Research Council, in turn, asked SME to collect and analyze workforce trends in these industries. The result of SME?s analysis is the report ?Emerging Workforce Trends in the U.S. Energy and Minerals Industries.? It is available on the SME website, www.smenet.org. Click on Government Affairs. While the report did not paint a completely dismal picture, there were some disturbing results. It concluded that within 20 years there will not be a sufficient number of skilled professionals to satisfy the labor demand. That said, the report said that most of those positions would likely be filled. However, the U.S. mining will go through a period of time when the workforce will be made up of very young and senior workers.

Jun 1, 2013

By Y. Mitani, M. Xie, G. Zhou, T. Esaki

The assessment of landslide instability and risk has become a topic of major interest for both geoscientists and engineering professionals as well as for local communities and administrations in many parts of the world. In this paper, based on a new developed Geographic Information Systems (GIS) grid-based 3D deterministic model and taken the slope unit as the study object, the landslide hazard is mapped by the index of the 3D safety factor. Assuming the initial slip as the lower part of an ellipsoid, the 3D critical slip surface in the 3D slope stability analysis is obtained by means of a minimization of the 3D safety factor using the Monte Carlo random simulation. The failure probability of the landslide is calculated by an approximate method in which the distributions of f,c and the 3D safety factor are assumed to be in normal distributions. The assessment of the earthquake triggered landslide hazard is done by the dynamic displacement analysis using the index of the Newmark displacement. All the calculations are implemented by a computational system call 3DSLOPEGIS in that a GIS component is used for fulfilling the GIS spatial analysis function. Besides the results of 3D safety factor and probability, the possible landslide body and boundary can be three-dimensionally quantitatively identified. L’ estimation des glissement de terrain et des risques impliqués est devenu un des principal sujet de préoccupation pour les géotechniciens, mais aussi pour les ingénieurs specialisés ainsi que pour les communautés et administrations locales dans de nombreuses région du monde. Dans cette étude, basé sur un modèle de maillage 3D et une approche déterniniste couplée au Système d'Information Géographique (SIG), étudiant la stabilité des versants , le lieu d'étude à risque est maillé suivant le facteur de sécurité calculé en 3D. En supposant que le glissement initial soit la partie inférieure d'un élipsoïde, l'analyse de stabilité pour le glissement critique 3D d'un versant 3D est obtenu grace à une minimisation du facteur de sécurité en 3D utilisant la méthode de simulation aléatoire de Monte Carlo. La probabilité d'un glissement de terrain est calculée par une méthode approximative, supposant la distribution de c, f et du facteur de sécurité 3D normale. L'estimation d'un risque de glissement de terrain causé par un tremblement de terre est faite grace à une analyse du déplacement dynamique suivant l'index de Newmark. Tous les calculs sont effectués par le biais d'un système de calcul appellé 3DSLOPEGIS dans lequel te GIS est utilisé pour gérer l'analyse spatiale. En plus de cela, les résultats du coefficient de sécurité en 3D, des probabilités, le terrain susceptible de glisser, et ses limites, peuvent être quantitativement évalués en trois dimensions. Die Bewertung von Erdrutsch-Instabilität und risiko sind zu einem Thema von großen Interesse für sowohl Geowissenschaftlern und Ingenieuren als auch von Gemeinden und Verwaltungen in vielen Teilen der Welt geworden. In dieser Arbeit, basierend auf einem neu entwickelten Geografische Informationssysteme (GIS) gitterbasierten 3D deterministischen Modell und mit der Böschung als Untersuchungsobjekt wird die Erdrutschgefahr durch den Index des 3D-Sicherheitsfaktors kartografiert. Unter der Annahme, dass der erste Rutsch der untere Teil eines Ellipsoiden ist, wird die 3D kritische Schlupfoberfläche in der 3D-Böschungsstabilitätsanalyse mit einer Minimierung des 3D-Sicherheitsfaktors mit der Monte Carlo Zufallssimulation erhalten. Die Fehlerwahrscheinlichkeit des Erdrutschs wird mit einer Annäherungsmethode berechnet, bei der die Verteilungen von f,c und dem 3D-Sicherheitsfaktor als innerhalb normaler Verteilungen angenommen werden. Die Beurteilung der Erdbeben-ausgelösten Erdrutschgefahr wird mit der dynamischen Verdrängungsanalyse mit dem Index der Newmark-Verdrängung gearbeitet. Alle Berechnungen werden mit einem Berechnungssystem mit der Bezeichnung 3DSLOPEGIS ausgeführt, bei dem eine GIS-Komponente zum Erfüllen der GIS räumlichen Analysefunktion verwendet wird. Neben der Ergebnissen des 3D-Sicherheitsfaktors und der Wahrscheinlichkeit kann der mögliche Erdrutschkörper und der Umfang dreidimensional quantitativ identifiziert werden.

Jan 1, 2003

By Steve Zaffron, Olga Loffredi, Eric Seedorff, Mary Poulton

"The New Face of Mining is a recognition of the central role of human beings in mining and the underappreciated power they can have in generating breakthroughs in business performance and shareholder value. The key is people creating, aligning on, and subsequently enacting the future of mining. A methodology that is effective creates a corporate environment for alignment to be possible and then transforms operations by embedding the necessary behaviors, processes and practices. The people within the organization then are empowered to find and to implement solutions quickly, as measured business results demonstrate in case histories of diverse mining challenges around the globe and over the decades.Urgent case for actionThe physics of mining does not change fundamentally over time, but the context in which it operates changes rapidly, periodically requiring a new face of mining. “The New Face of Mining,” which has been used as a metaphor for the campus-wide mineral resources research organization at the University of Arizona, has many facets, including societal, generational, technological, financial and environmental, but at the center, always, is humanity. The New Face of Mining is not necessarily about age, it is about people first imagining and then creating a new future for mining. The challenges facing the global industry evolve from year to year and differ in individual companies or mines at any one time.Quantified outcomes from case studies indicate that a methodology, now also offered annually in a four-day, open-enrollment leadership program tailored to the mining industry, is effective at generating breakthrough results in the mining business. Such challenges range from those with important technical components to others that are mostly social challenges. Our focus, however, is the centrality of people in aligning on and enacting the future of mining. We use the phrase New Face of Mining for leadership and ways to empower people in organizations that commonly are overlooked in the mining industry. Some of the material in this article is based on the ideas of Werner Erhard and on the book by Steve Zaffron and Dave Logan (2009), The Three Laws of Performance: Rewriting the Future of Your Organization and Your Life.At Davos, Switzerland in January 1992, nine visionary mining chief executive officers (CEO) gathered to create the Global Mining Initiative. Much has changed in the 26 years since that meeting:• The world GDP has increased from US$25.4 trillion to $75.8 trillion.• The annual number of U.S. patent applications increased from 186,000 to 629,000.• The number of websites has increased from 100 to 1 billion.• The number of academic references to artificial intelligence has climbed from more than 16,000 to more than 1 million.• The number of cell phone subscribers grew from 11 million in the United States to four billion globally."

Oct 1, 2019

By J. Postle, Deborah McCombe

"This is the third in a series of articles about the Committee for Mineral Reserves International Reporting Standards (CRIRSCO). The first article was an interview with Niall Weatherstone, Chairman of CRIRSCO (CIM Magazine, February 2008) the second described the background and goals of CRIRSCO (CIM Magazine, March/April 2008). In 2007, CRIRSCO was adopted as the Reserves and Resources Task Force of the International Council on Mining and Metals. This decision by ICMM has resulted in an increased level of funding for CRIRSCO and the ability to advance its objectives. In mid-October 2007, CRIRSCO members met in London England to discuss the status of each of the member countries’ reporting codes and the progress of various CRIRSCO projects. Update on national reporting codes Australia: The last update of the Australian JORC Code was in 2004. While there are ongoing discussions about issues that arise from the application of the latest version of the Code, there are no plans to update JORC in the near future. Canada: The Canadian Securities Administrators revised National Instrument 43-101 in December 2005. At the same time, the Canadian Institute of Mining, Metallurgy and Petroleum published updated Resource and Reserve Definitions that are incorporated by reference in NI 43-101. CIM is continuing work on developing Best Practice Guidelines to assist practitioners in the estimation of Mineral Resources and Reserves. South Africa: The South African Mineral Reserve Committee is currently awaiting an update of the Johannesburg Stock Exchange Limited Listing Rules, which will incorporate both SAMREC and SAMVAL (South African valuation guidelines). The official launch of both codes is expected in 2008. Europe: The Pan-European Reserves Reporting Committee expects to release a consultation draft in 2008. Emphasis is being placed on industrial minerals and aggregates, which constitute a very large industry in Europe. Chile: The Chilean Certification Code was approved in early 2008. As part of the Code, a National Commission is being established to screen and review reports on a random or specific basis. United States: The Society of Mining Engineers updated the SME Reporting Guidelines in 2007. The Securities and Exchange Commission has not accepted these more up-to-date definitions and guidelines. The SME committee will continue to discuss the incorporation of these Reporting Guidelines with SEC. SME has also established a class of membership, a Registered Member, which includes disciplinary measures for non-compliance with the SME guidelines."

Jan 1, 2003

By F. A. Rutledge, J. J. Mulligan, W. H. Kems, R. L. Thome

"As a part of the United States Department of the Interior program for the development and use of Alaska raw materials, the Bureau of Mines is conducting an investigation of deposits f nonmetallic minerals accessible to the Alaska Railroad for use in building materials in the Alaska Railroad-belt area. The results of the investigations, to date, indicate that raw materials for the production of brick products are in plentiful supply as clay in the Anchorage area, as fire clay at Sheep Mountain, and as shale in the Healy Creek coal formations near Healy, Alaska.Shale for the production of lightweight aggregate or Haydite occurs near mile 67 on the Glenn Highway, and preliminary tests give excellent results. Physical tests are new in progress on commercial-size concrete building units made with this aggregate. Another shale deposit in the same formation was located at mile 16 on the Matanuska Branch of the Alaska Railroad, and preliminary tests give comparable results.Natural lightweight aggregate in tree form of pumice and pumicite occurs in Katmai National Monument and has been used with excellent results in lightweight-building units in Anchorage and Fairbanks. These deposits will be investigated in more detail by the Bureau of Mines during 1952.One small perlite deposit near Healy, Alaska, showed excellent expanding properties, and the product compares favorably with commercial perlites being used in the States for plaster and concrete aggregates. Additional investigation by the Bureau of Mines to delimit the known occurrence and, if possible, discover others were planned for the 1951 field season.The pumice from Katmai National Monument also was considered for use as a pozzolan in pozzolan-portland concrete. Tests by the Bureau of Reclamation indicate that the pumice sample submitted by the Bureau of Mines would be satisfactory in strength development but is not outstanding. Natural activity is good and is greatly improved by calcination at 1,4000 F. Water requirements and shrinkage also are satisfactory. However, the material is ineffective in reducing expansion owing to alkali-aggregate reaction; and, if reactive aggregate is used to make concrete, it would not insure against excessive expansion. An attempt will, be made during the 1952 field season to delimit pumicite deposits along the Alaska Peninsula more amenable for use in pozzolan-portIand concrete.Because the Railroad belt has such a rigorous climate, insulation for new construction is of prime importance. Luring the Bureau of Mines, investigation of building materials all samples were submitted for chemical analyses as possible sources of raw materials for the production of rock wool, one of the best insulation mediums. Four areas having deposits of the required constitu¬ents were located as follows: Anchorage area, with Potter limestone and argillite; Cantwell-Windy area, with limestone and shale; West Fork of the Chulitna River area, with limestone and agrillite; and Homer-Seldoyla area, with Seldovia limestone and Homer clay. It was planned to take bulk samples of these formations and submit them for testing during the 1951 field season."

Mar 1, 1953

By Edward P. Barrett

SPONGE IRON has been defined as the metallic product formed by the reduction (removal of combined oxygen) of iron ore or other iron oxides at temperatures below the fusion point of iron. This product probably derived the name "sponge iron" from its porous nature. When the reduction proceeds at slightly higher temperatures and the particles of metal weld together or finally even melt to yield pellets or balls that lack the porosity and low-density characteristic of sponge iron, the product might more correctly be called "direct iron."

Jan 1, 1954

By Thomas Lane Carter

THE history of mining in South Africa differs somewhat from that of other countries in the part taken by the aborigines in the development ?of the mineral deposits. The Spaniards in America, and the fortune-seekers of Australia and New Zealand, found large numbers of natives in these new countries, but the inhabitants did not become willing or efficient workers ill the mines which the white men started. The Kaffirs of South. Africa have not shown the same antipathy to labor, nor do they show any signs of dying out in the presence of the white man's civilization. They are a virile race, and so far the vices of civilization have not killed. them. While it is true that the brain and skill necessary for the exploitation of the mineral resources of this sub-continent-have been supplied by the white race, it is also a fact that most of the rough labor in the development of the mining industry of South Africa has been done by the Kaffirs. The Kaffir tribes differ greatly in their mental and physical capabilities. Compare, for instance, a Zulu of Natal with a Bechuana, or a Xosa of Cape Colony with some of the degenerate tribes of Central or East Africa, and you will find that they have little in common, save that their skin is black and that they do not believe in clothes. As a general rule, the tribe's in the milder, healthier climates are far superior, both in mind and body, to the Kaffirs brought up in the hot malarial sections of Central Africa; and it naturally follows that the black men from the temperate zones of the country, are much finer workmen than the degenerates from less favorable sections: It is universal in South Africa to speak. of the .Kaffirs as " boys." No matter if he is 90 years old, the Kaffir is always a " boy," and in this paper the word " boy " is synonymous with Kaffir.

Nov 1, 1908

By Hardwick F. W., O'Shea L. T.

The survey covers: coal-mine lighting prior to the invention of the safety-lamp, including candles, the flint-and-steel Spedding mill, and mirrors; the growth in knowledge of firedamp; the Society in Sunderland for Preventing Accidents in Coal Mines; Dr. Clanny's blast lamps and steam lamps; George Stephenson's tube-and-slider lamp, triple-tube lamp, punched-plate lamp and gauze Stephenson lamp; Sir Humphrey Davy's lamps; the controversy over invention priority, and other early forms of safety-lamp; 1816-1835 developments including the lamps of Upton and Roberts, M.Mueseler, John Martin, Dr. Clanny (new 4th lamp), M. Agre, John Newman, Gossart and Roberts, Francis Ellis, John Dillon and Mr. Wood (refrigerating lamp); 1836-1843 developments, notably of Mueseler lamps; 1844-1866, including lamps of the Davy, Clanny, Boty, Eloin and other types; 1867-1879, including the Gray lamp; 1880-1887, including the Marsaut lamp; and 1888-1913. Detailed reference is made to the findings of various relevant Royal Commissions and appendices include a list of the safety-lamps described in an appendix to the 1886 report and a publications list. The paper was prepared for the International congress of mining, metallurgy, applied mechanics and economic geology to have been held in London in July 1915. Discussion (p.718-724) includes a brief comment by Blackett W.C. and a longer contribution by Ashworth J., with the authors' response

Dec 1, 1916

By Jack Bedder

"Editor’s note: We would like to thank those who make this annual issue possible. A special thank you goes out to the industrial minerals annual review editor, to the Industrial Minerals & Aggregates Division Technical Committee chair and vice chairs, and to the authors of the individual commodity profiles.Jim Norman, member SME, of Tetra Tech, is the industrial minerals annual review editor.Ebrahim K. Tarshizi, member SME, of Michigan Tech, is chair of the Industrial Minerals &Aggregates Division’s Technical Committee.The technical committee vice chairs include: • Hyunjung Kim, member SME, of Chonbuk National University, agricultural materials.• Xihui Yin, member SME, of Kemira, ceramics and refractory materials.• Nikhil Gupta, member SME, of Virginia Tech, chemical raw materials.• Jasson Giddens and Swadhin Saurabh, members SME, of Oil Dri Corp of America and Mill Creek Engineering, respectively, chemical raw materials.• Snehamoy Chatterjee, member SME, of the Michigan Tech.• LeDeana Roberts and Shubham Verma, members SME, of Imerys and U.S. Oil Sands, respectively, fillers and pigments.• Thomas Hilderbrand and Kaiwu Huang, members SME, of Thiele Kaolin Co. and Virginia Tech, respectively, sorbents, filters and process aids.• Rhaghav Dubey and Edgar Blanco, members SME, of Outotec and FL Smidth, respectively, specialty mineralsAntimony generally occurs along with gold, lead, copper and silver. There are more than 100 antimony minerals, although the sulfide mineral stibnite is the main one.Antimony enters the supply chain either as a result of mining (primary production) or recycling (secondary production). China has by far the largest antimony resources and is, as a result, the world’s center for antimony mine production. In 2016, it accounted for more than three quarters of the global mine supply out of a world production figure of 130 kt (143,000 st), according to the U.S. Geological Survey. The biggest, and most high-grade deposits are found in southern China, with the largest mines located in Hunan, Guangxi and Yunnan provinces. Tajikistan, Russia, Australia and Bolivia are the largest mine producers outside China. A new antimony project in Oman made progress in 2016, producing first metal in April 2016 in test facilities, and then ordered three furnaces for a 26 kt/a (28,600 stpy) antimony metal and oxide smelter that is due on stream in late 2017.Antimony ingot production is not as widespread as is antimony mine production, owing to the high levels of pollution that are associated with antimony smelting. It is for this reason that smelting has been largely confined to China and other Asian countries, where environmental legislation is less stringent.Antimony oxide production is undertaken on four continents with China being the biggest producer. There is also a considerable amount of oxide production in Europe — which relies on imported feedstock, mostly from China. Antimony also enters the supply chain through recycling. Lead containing antimony is produced in a number of countries, mainly in secondary lead smelters. Typically, a blast furnace charge containing used or discarded battery plates, type metal or bearing metal is reduced to lead bullion, which is refined in reverberatory furnaces and melting pots. In the main, the antimony recovered is consumed in metallurgical applications. China was the biggest secondary antimony producer in 2016, and accounted for 25 retardants and lead-acid batteries. Flame retardants accounted for roughly 50 percent of consumption in 2016 with batteries representing about 25 percent. Other end uses include plastics and heat stabilizers, ceramics and glass and a variety of metallurgical applications. Demand has been sluggish since the global financial crisis, mostly because key markets failed to recover strongly from the downturn, particularly in Europe."

Jan 7, 2017

On June 4, Kennecott Utah Copper (KUC)marked the centennial of the founding of the original company. Bill Champion is president and chief executive officer of KUC. He said, “What has happened during the past 100 years far surpassed even the most optimistic visions of men like Daniel C. Jackling and Robert Gemmell when they promoted the concept of mass production techniques for a low-grade deposit of copper ore. At that time, it was a totally new way of doing things and the mining leaders of that day scoffed at the idea. They said it would never work,” Champion said. The company will celebrate this once-in-a-lifetime occasion with a few special projects, mainly for the benefit of our employees, said Louie Cononelos, director of government and public affairs for KUC. The company has designed and minted a commemorative copper coin that reflects early steam shovel and locomotive operations on one side, and today’s modern electric shovels and huge haulage trucks on the other side. “The history of the company stems from the ores of the Bingham Canyon Mine. That coin has been encased as part of a10-panel brochure that captures the company’s 100 year history,” he said. KUC also developed special centennial banners and comparable framed posters that were displayed throughout its operations and at selected community locations that have enjoyed a long-time partnership and special relationship with the company. Some of the plants also designed their own centennial hardhat decals.

Jan 1, 2003

By O. P. Hood, R. H. Kudlich

When a gasoline locomotive is used in a mine there is danger of the noxious gases of the exhaust vitiating the air, but if enough air is circulating in those parts of the mine in which the locomotive is used, these gases are so diluted that they are rendered harmless, and the health of the workmen is not affected. In some mines the use of gasoline locomotives is impracticable, though in the majority of mines where they have been tried they have proved to be safe and economical. To determine the limitations that should surround the use of these machines in mines so that they shall not be detrimental to health and so that their economic advantage may be retained, it is necessary to ascertain the volume and the character of the exhaust gases and the amount of these gases that may be safely allowed in the mine air, and also to determine safe conditions of operation. The problem is primarily one of ventilation and like all ventilation problems must be intelligently computed to meet the conditions of each mine. The investigation described in this bulletin was undertaken 'by the Bureau of Mines in an endeavor to obtain exact information on some of the basal questions involved in the use of gasoline locomotives in mines, this investigation being one of many that the bureau has been conducting in its efforts to increase safety and efficiency in mining.

Jan 1, 1915

[This Report represents the culmination of work perfomed under Contract No. .,JG1551A8 for the U.S. Bureau of Mine.The &apos;.:o-< embeded a site evaluation, engineering E:-y- ,, esign, and preparation of specifications for construction of a Transport Research 7 :4 (HTRF)The HTRF is designed as a research facility J evaluate the hydraulic transport of large lump coal at a prototype ;e scale. The HTRF is to be constructed and operated by the Pittsburgh and Safety Research Center of ;. re U.-AN a*, their Bruceton, Pennsylvania test center. In terms of technical capability, the HTRF will have transport pipeline:: of -, twelve-, and eighteen-inch diameter _&apos; with supporting coal handling n , water forage a.^ &apos;d conveyance, mixing, pumping, and dewatering equipment, plus instrumentation and controls. Maximum design velocity 13 20 ft/sec.; solids concentration, by, volume, will; 1 be a maximum-- of sixty, percent. Each test loop is designed to accommodate solids of up to one-third the diameter e - of the pine. The Final Report Pr.-&apos;I-rents information of t HTHF,. including the site evaluation, design criteria, a description of the a description of the procedure to be used for operation of the facility, an estimate of the cost to construct the f^Cilit:r, 1 p el_~lli.&apos;iU construe`, icn Schedule, and a construction suicJ_iicaT.l_ccn&apos;. T e c011SLr?Jc&apos;.ion soecl_ i.on _ccnta_i:s technic.&apos;..i re7,uir: (-n`,s for !&apos;urr1S~ &apos;~latcr..al. and ec-uipr,ent for :":C1 C_`:_C ti on of ti,_ H ice&apos; u:&apos;.:i ._II u s(-.6 for ~.Iir: .3!7 soliciting bids. `.l_o included n cc&apos;;,art_- c?r~.air sV:et..: :s ^nd rr^.?]

Jan 1, 1976

By Robert Lee, Jeff Corace, Rob Cyr

Blasting in the heart of the historic Byward Market District of Canada’s capital, Ottawa, presents a unique set of challenges. The obvious difficulties arising on projects requiring blasting within 3 m (10 ft) of 125 year old buildings in various states of disrepair have been encountered and successfully dealt with countless times before. The complexities increase exponentially when tenuous property boundaries, unknown structural details, litigious histories and the need for encroachment agreements lead to individuals with competing interests all able to impact the same operation. Blasting on three projects in the Market was started in early 2005 after months of negotiation. Ultimately, the potential for the projects to proceed hinged on the ability to successfully disseminate blast data to the various stakeholders. As part of the agreements drawn up, property owners demanded immediate notification of the measured vibration levels with contract provisions including clauses such that any exceedance of the USBM criteria immediately triggered project shut down and complete blasting program redesign, and approval by all parties. With stakeholders located in various cities and, in some instances, on various continents, a conventional attended monitoring strategy would not satisfy the requirements. In response to the critical reporting need, Explotech Engineering Ltd. installed unattended monitoring stations around the sites, all incorporating wireless telemetry. After each blast, data was automatically transferred from the monitoring stations to a web-linked server via the wireless network, where it was immediately available to project stakeholders through a password protected website. The solution required a unique blend of data acquisition, telemetry, database, and security technologies, all married to produce a reliable system that was easy to maintain and use. While these types of systems were originally developed for use as permanent monitoring networks in operating mines and quarries, monitoring professionals are increasingly benefiting from the technology on temporary building projects that have typically been the realm of attended monitoring strategies. Globally, this has emerged as a solution to provide more timely access to data for stakeholders, and to minimize the legal exposure from multiple violations of vibration limits. As this trend is likely to continue, the regulated vibration control industry is likely to see a continued shift in technology development to leverage wireless networks and the Internet to continue to improve data transfer, archiving and distribution.

Jan 1, 2006

By Sara J. Davenport

With the increased demand for mercury incident to preparations for national defense and the reduction in imports from some of the usual sources owing to war conditions, many small mines in the United States Pure now being worked that ordinarily would be unprofitable. This is indicated by the following table on mercury produced in the Unite States in 1939-40 (1)4/

Jan 1, 1941

By E. D. Gardner

Placer mining is the mining and treatment of alluvial deposits for the recovery, of their valuable minerals. The method has been used principally for mining gold, but a large proportion of the world&apos;s production of tin, platinum, and diamonds and other gem stones and minor quantities of other heavy minerals have been won in this manner. In the United States, as in the world at large, gold has been the principal mineral obtained by placer mining. Minor quantities of metals of the platinum group are recovered with the gold in some localities. Important quantities of sapphires have been produced at placer mines in Montana, and tungsten minerals have been obtained on a commercial scale from placer deposits in California and Colorado. Other heavy minerals or gem stones, however, have not been mined to any important extent by this method in the United States. The search for placer gold and the working of the deposits when found have had much to do with the early development of the West. Placer mining has been gradually overtaken and surpassed in importance by lode-gold mining, until in 1932 less than a quarter of the country&apos;s total gold production was from placers or about an eighth, excluding Alaska. In 1932 about 76 percent of the placer gold produced in the United States was recovered by dredging. Although other forms of placer mining still are important, they have been declining for many years, as the richest and most readily mined deposits of gravel along the stream courses have been exhausted. During 1931 and 1932 there was a revival of small-scale mining, but few new deposits were discovered.

Jan 1, 1934