Search Documents

The work described herein is the opening phase of an extensive system of underground excavation undertaken under contract with a Malayan authority.The specifications called for the lining of all tunnels in earth or broken rock with circular segmented cast iron lining, similar to that of the London tubes, and it is the installation of these linings which it is proposed to discuss.Owing to the long deferred delivery quoted and the obvious need for speed of access to the internal installation, it was decided to defer driving the completed circular section and substitute two small timbered headings.These could later be opened out in turn to full section and lined without prejudice to traffic, since both of them had access to the internal workings.NATURE OF ROCKThe rock series through which the circular sections were driven consisted of:(a) A wide zone of intrusive porphyritic granite, consisting generally of orthoclase phenocrysts in a ground mass of micro pegmatite. This area showed advanced weathering, varying from a stage showing slightly tinted kaolin containing approximately 20% of small boulders to one of ultimate decomposition to pure kaolin;(b) A narrow zone of weathered augite diorite, consisting of rock masses of a maximum weight of some 100-150 tons, isolated by clay seams up to 1 ft. 6 in. in width.The whole area was in a state of quasi-hydrostatic equilibrium, which resulted in heavy pressure immediately after excavation. Freshly broken faces would appear to be quite solid but, within a few minutes, would commence to sweat and "slab off" under pressure and, unless support was placed promptly, the whole face would burst out and run from above. Mucking was slow, owing to the plastic nature of the clay and the ease with which it puddled into slurry.In zone (b) a good deal of trouble was experienced because of the fact that the somewhat heavy blasting necessary tended to cause movement of the large rock masses. Subsequent scouring out of the supporting clay bands by the waterflow permitted settlement of the ground on to the timbers and many reinforcing sets were therefore required.The timbering of the pilot headings and its relation to the cross-section of the circular tunnels is shown in Fig. 1. Top and side spiling was driven in the ordinary way, but in bad ground intermediate sets and breast boards had to be placed. These sets were usually withdrawn after the...

Jan 1, 1941

By MacKenzie Dickson

"INTRODUCTIONGold is found in many natural states, native nuggets, loose grain in river sands, veins in rock, as well as associated with sulphides, oxides, etc., disseminated more or less minutely.Its high value in recent years has spawned new technologies to win values from sources once considered too lean for commercial recovery. Cyanide leaching from fine milled ore or tailings, from upstream recovery operations, coupled with adsorption onto relatively coarse granules of activated carbon, concentrate the gold enough to be converted to bullion by time-honoured methods.The carbon granules are fragile. Size degradation in handling must be minimized not only to prevent loss of gold on fine fragments of carbon that could pass with the barren tailings, but to maintain adsorption efficiency. Besides, the granulated carbon itself is costly. Circular Vibroscreens are winning acceptance for dewatering carbon granules thanks to their gentle yet effective performance in gold recovery systems around the world. The system at Equity Silver is illustrative.BackgroundEquity Silver Mines Ltd., Houston, British Columbia, first began production in September 1980. In 1984, a feasibility study showed that additional gold and silver could be economically recovered through cyanide leaching of the flotation tailing.Although the carbon-in-pulp (ClP) or carbon-in-leach (CIL) process is commonly used for extracting precious metals from slurries, the use of circular vibrating screens, and Vibroscreens in particular, for the carbon circuit is an innovation that cuts costs.Rectangular vibrating screens have been the conventional separation mechanism of choice across North America. In contrast, the use of Vibroscreens has been proven to be less costly for the initial purchase and installation. Also, these circular vibrating screens require less power and less space. A description of Equity Silver Mines' process shows how these screens have been successfully integrated into the system."

Jan 1, 1989

Circulating Air Classification of Manufactured Sand Due to environmental concerns, the supply and use of natural gravel has been limited by the Swedish government. The Swedish concrete industry is therefore examining manufactured sand as an alternative that has equal or better product quality, and which the Swedish quarry industry already has the ability to deliver. However, in order to comply with the specifications set by the concrete industry, a better means of classification is needed, as the proportion of fine particles (filler) smaller than 63 - 125 ¦m in size must be reduced. One classification technology that meets the requirements may be air classification. This paper examines the process of circulating air classification, which is not yet commonly used in the Swedish quarry industry; suggesting that a better understanding of the process is needed. The circulating air classifier in this study has two internal machine parameters that can affect the separation point; namely, the speeds of the circulating fan and the separator fan. We study their effect on the separation point as well as the interaction between these parameters. Full-scale parameter tests are also conducted, in which size distribution is measured before and after the circulating air classification. This study shows how the different parameters affect the separation point and that it is possible to produce manufactured sand according to specifications. Computational fluid dynamics (CFD, Fluent) is used to study the internal flow of the air circulating within the classifier. A single-phase study of the flow field is conducted to support and explain the findings from the full-scale tests.

Sep 13, 2010

By T. B. Jarboe, H. Wen

Introduction The 150 MW circulating fluidized bed (CFB) power plant described in this article is the product of recent Bechtel experience in the industrial power and steam market, where the economic feasibility of fluidized bed projects has been proven. The ability of CFB boilers to burn low grade fuels makes it possible to burn low ranking coals or coal wastes. These include anthracite culm, coal mine rejects, and coal wash-plant-waste slurries. This article also addresses the impact of fuel characteristics on plant design. This includes solids handling, steam generation, sulfur capture, and auxiliary load requirements. The uncertain economic environment in which utilities must now operate has shifted the industry's interest away from large, base-loaded generating units to small, more versatile installations. Utilities now consider purchasing new generating capacity in smaller increments and staging its deployment to correspond with demand increases. In this way, they lower their risk in the increasingly hazardous art of long-range load forecasting. This strategy has many advantages. Multiple, smaller units have inherently greater turndown capability and better availability than a single larger unit of the same size. In addition, the smaller units will each have better cycling capability. And, with CFB combustion, the smaller units will have greater fuel flexibility. General plant description The 150 MW powerplant described here is a grassroots CFB unit. Fluidized bed technology differs from conventional combustion techniques. With CFB, solid fuel, together with inert material such as sand, gypsum, limestone, or ash from the fuel, is kept suspended in the combustion chamber. This is done by using the action of the fluidizing air distributed below the bed. Fluidization promotes the turbulent mixing conditions required for good combustion. The turbulence causes the entire mass of solids to behave like a liquid. The result is improved mixing. This allows heat to be generated at a lower and more uniformly distributed temperature that is below the ash fusion temperature of most coals. The fluidizing mechanism offers several other advantages over conventional combustion. There is less volatilization of alkali compounds, which cause deposits on boiler tube surfaces. And there is less sensitivity to the quantity and nature of the ash in the fuel. The low combustion temperatures prevent vitrification of the ash particles and minimize problems associated with furnace slagging. The ability to select from many fuels is one of the major advantages of CFB combustor technology. Fuels that can be burned in CFB plants to produce steam and electricity include: low grade coals with high ash or sulfur, lignite, peat, wood and pulp products, biomass, refuse, anthracite culm, petroleum coke, and oil shales. The plant's turbine cycle uses superheated steam at 12.4 MPa (1800 psi) and 538°C (1000°F), with single reheat to 538°C (1000°F). Two high pressure and three low pressure, closed, feedwater heaters are furnished. So is a deaerator, which is an open, direct-contact heater. The CFB plant exceeds EPA's New Source Performance Standards (NSPS) for air emissions. The design limits sulfur dioxide (SO,) emissions to 0.25 kg/GJ (0.6 lb per million Btu). SO2 reduction occurs in the combustor by reac-

Jan 11, 1988

By Antti Porvali, Vivek Agarwal, Mari Lundström

Hydrometallurgical recovery of rare earth elements (REE) from NiMH battery waste can be performed using sulfuric acid leaching followed by selective precipitation as double salt (REENa(SO4)2·H2O) by adding Na2SO4 as a precipitating agent. The formed double salts can then be further converted with NaOH solution to form REE hydroxides. However, present literature has paid little attention to how to minimize the consumption of reagents in this recovery process. In the current study, a process model was built using HSC Sim software, and metamodeling of the simulated flowsheet was conducted with the design of experiments (DOE), after which the basic functionality of the flowsheet was verified by experimental work, starting from sulfuric acid leaching of spent batteries. As the process is based on chemical circulation internally in the process, the objective was to investigate the accumulation of the elements in solution, specifically Na+ , K+ , SO4 2− ions and impurities liberated in the NaOH conversion step. It was found out that metamodeling could be utilized in obtaining first estimate of the process behavior, prior to any experiments. Flowsheet functionality with circulated solution was confirmed, obtaining at best 96.9% La recovery.

By Antti Porvali, Vivek Agarwal, Mari Lundström

Hydrometallurgical recovery of rare earth elements (REE) from NiMH battery waste can be performed using sulfuric acid leaching followed by selective precipitation as double salt (REENa(SO4)2·H2O) by adding Na2SO4 as a precipitating agent. The formed double salts can then be further converted with NaOH solution to form REE hydroxides. However, present literature has paid little attention to how to minimize the consumption of reagents in this recovery process. In the current study, a process model was built using HSC Sim software, and metamodeling of the simulated flowsheet was conducted with the design of experiments (DOE), after which the basic functionality of the flowsheet was verified by experimental work, starting from sulfuric acid leaching of spent batteries. As the process is based on chemical circulation internally in the process, the objective was to investigate the accumulation of the elements in solution, specifically Na+ , K+ , SO4 2− ions and impurities liberated in the NaOH conversion step. It was found out that metamodeling could be utilized in obtaining first estimate of the process behavior, prior to any experiments. Flowsheet functionality with circulated solution was confirmed, obtaining at best 96.9% La recovery.

By A. Porvali, V. Agarwal, M. Lundström

Hydrometallurgical recovery of rare earth elements (REE) from NiMH battery waste can be performed using sulfuric acid leaching followed by selective precipitation as double salt (REENa(SO4)2•H2O) by adding Na2SO4 as a precipitating agent. The formed double salts can be treated further with NaOH solution to form REE hydroxides. This study focuses on metamodeling of a simulated flowsheet with design of experiments (DOE). Based on literature survey, a process flowsheet was developed using HSC Sim software. The created flowsheet focuses on circulation of solution containing Na+, K+, SO42- ions and impurities liberated in the NaOH treatment of double salt precipitate. The effect of seven parameters (P1-P7) on seven responses (R1-R7) were modeled using central composite design (CCD). INTRODUCTION Nickel metal hydride (NiMH) battery waste can be considered as an urban mineral due to the presence of valuable metals like: Ni, Co and rare earth elements (REE) (Larsson et al., 2013). In NiMH battery waste leaching experiments, sulfuric acid has often been employed as a lixiviant (Pietrelli et al., 2002,Zhang et al., 1999,Rodrigues and Mansur, 2010,Porvali et al., 2018). The key advantages of sulfuric acid are its stability and cost-effectiveness compared to other mineral acids such as HCl and HNO3. However, the usage of sulfuric acid in NiMH battery waste leaching poses simultaneous challenges and advantages. Limited REE solubility can be taken as benefit when recovering REEs double sulfates after solid-liquid separation. However, sodium and potassium hydroxide, present in electrolyte residues in the battery waste, can cause in-situ precipitation already during leaching due to limited solubility, thus decreasing the total REE recovery (Porvali et al., 2018). However, this problem can be circumvented by washing the electrolyte residues off the raw materials. Subsequently, the REEs may be precipitated in bulk as a mixed double salt out from the solution at very low pH with minimal co-precipitation of Ni and other metals. This relatively easy separation method can be extremely advantageous in the case of such a complex solution matrix with relatively high REE concentrations (conc.). Once REEs have been precipitated as double sulfates as per eq. (1) (Porvali et al., 2018), the resulting double salt precipitate lacks applications without further treatment. Direct thermal treatment would generate sulfur dioxide emissions and likely require high temperatures in order to transform double sulfates into REE oxides. Furthermore, the precipitate contains Na ions, which would need to be removed by chemical treatment from the calcined REE product. In the context of circularity of raw materials, it can be taken of a remarkable benefit if the sodium and sulfur present in the double salt could be reused instead of wasting them into the side streams. To that end, in this simulation study, the double salts are converted by dissolution and precipitation to hydroxides which are readily treatable, e.g. with total dissolution and solvent extraction, for further purification (Abreu and Morais, 2010):

Jan 1, 2019

By P Hollings, J Holliday

Porphyry copper, gold and molybdenum deposits form in subduction-related settings in association with calc-alkalic or alkalic magmatism. Hydrothermal alteration assemblages are zoned, with potassic cores and propylitic haloes overlain by extensive domains of clay alteration and silicification (lithocaps). Copper sulfides, gold and molybdenite typically occur in veins or hydrothermal breccias, and less significantly as wall rock replacements. Epithermal deposits may form above or to the side of porphyry systems, and may be juxtaposed into the core of a porphyry deposit if rapid uplift and exhumation occur through the life of the magmatic-hydrothermal system. Volcanichydrothermal breccia pipes (ædiatremesÆ) commonly form late in the life of a porphyry system. They may contain clasts of porphyry-style mineralisation, and can host significant epithermal gold resources. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

A number of terrane reconstructions conflict with global plate histories or with data from adjacent regional studies. Paleogeographic maps have ignored terranes thus are over-simplified. This paper represents an attempt to "marry" Mesozoic global plate reconstructions and terrane analysis to produce examples of a "third generation" of global plate tectonic maps. The best approach to global terrane analysis involves intercomparison of all regional data and the evolving global model. Data conflicts within and between terranes and regions must be resolved by a system of relative data reliability "weighting." The most reliable and useful data are those which constrain "departure" (rift) and "arrival" (collision) times. Certain ad hoc decisions aid in the analysis (e.g. only one net vector allowed per plate). The maps that follow summarize Early Mesozoic global tectonic history at three critical junctures: 240 MA (Triassic); 180 MA (Jurassic); and 120 MA (Cretaceous). Due to space limitations, maps drawn at 20 m.y. intervals appear elsewhere. A preliminary Middle Triassic reconstruction is presented in Figure 1. Major plates and continental blocks are labeled; smaller blocks are marked with abbreviations. Examination of Figure 1 indicates the necessity of modeling Triassic tectonics with at least 68 blocks. Spalling- off of microcontinental slivers from Gondwanaland is active some 70 m.y. before the actual breakup of the supercontinent. In the SW sector of the Pacific, the Australian margins were embroidered with several terranes (e.g. Sumba) which eventually rifted away and crossed Tethys. The NW sector at this time included 10 microcontinental chips forming a huge archipelago along the Asian margin. All blocks inboard of Indochina collided by latest Triassic. Terranes of the NE sector include several (e.g. Arctic Alaska) along the North American margin, and at least six large blocks (e.g. Stikinia) drifting SE with the Farallon Plate. The SE sector

Jan 1, 1987

The need to describe shape properties of solid particles arises in many applications in the mining and minerals industry. This paper presents a technique for describing the shape of 2D particle profiles from digital images, based on traversals of the circumference of the profile boundary at a succession of different scales. The traversals are undertaken in such a way as to establish a more stable set of results than usually arises from conventional fractal multi-scale shape characterisation techniques. The resulting values can be used to provide compact information on various generic shape features of the particle profile.

Jan 1, 1998

By M. R. Nelson

Continuing experience in the Black Hills, South Dakota, indicates the persistence of several natural contaminants in mine waste effluents under circumneutral pH conditions. Selenium and arsenic are the most problematic environmental contaminants observed in these effluents. The contaminants are present in ore and waste rock as naturally occurring trace elements, and under the physico chemical conditions of the mine waste repositories are mobilized by oxidation and desorption reactions into infiltrating water. Characteristics of the mine wastes, waste repository construction, and Black Hills climatic conditions, indicate these natural contaminants may persist well into the future causing long-term mine closure liabilities, a difficult challenge to both mine operators and regulators.

Jan 1, 2003

By K. Ford, R. Urquhart, D. Hobbs

CIS countries are home to some of the world's largest producers of chrome, manganese and silicon ferro alloys and leading suppliers to world export markets. The region's ferro alloys production is rising faster than demand from its domestic steel industry - unit alloy consumption in domestic steelmaking is in fact falling as process efficiencies improve - and there is significant spare capacity available to increase production. CIS producers enjoy certain strategic advantages in the production of ferro alloys - for example, captive ore sup-plies, low power and labour costs - but must also meet certain challenges - such as lower labour productivity and greater distance to market than some of their competitors. CIS producers are ambitious but new investment is needed to upgrade some aging plants and overhaul outdated process technologies if they are to be more competitive with the world's leading producers and address the environmental issues that are now moving up the agenda. This paper describes the structure of the region's ferro alloys industry and discusses its advantages and disadvantages by alloy and by country. It considers how the ongoing process of restructuring and new investment in the industry might move forwards, based on its strengths and weaknesses, technical and environmental factors and the strategies of the main players. It asks how the industry might maximise its substantial potential - in particular, for the production of chrome and manganese ferro alloys - and examines the implications this holds for all global ferro alloys players.

Jan 1, 2007

By P. G. Semple

For the last four years, the Kilborn Group of Companies has been involved in several major projects in the Confederation of Independent States (CIS). These include the Kumtor project, the Kubaka gold project, the Kazgold project, the Aginskoe project and the Jerooy project. These projects are all in various stages of detailed engineering and construction. Western mining companies are pursuing mining opportunities throughout the world in search of ore bodies for development. The quest for profitable mining ventures has led mining companies to South America and Asia and, more recently, to the former Soviet Union. When considering the CIS, several factors should be considered. The most notable are geography, mining culture and previous mining production.

Jan 1, 1996

By P. G. Semple

For the last four years, the Kilborn Group of Companies (Kilborn) has been involved in several major projects in the CIS. These projects include the Kumtor Project, the Kubaka Gold Project, the Kazgold Project, the Aginskoe Project and the Jerooy Project. These projects are all in various stages of detailed engineering and construction. In this paper, Kilborn will discuss our experience in the CIS and share some insight into project development in this geographic region.

Jan 1, 1996

By Huang Qiming

The CISDI-GreenEAF innovatively applies the top-side-chute for charging for improving the cold zone of electric-arc furnace (EAF) requiring preheating scrap. It can greatly reduce the operating power consumption during EAF melting by combined use of fume for preheating scrap. The enclosed charging mode and specially-designed structure contribute to less emission of dust and fume during charging while enhancing the metal yield. Thanks to the extraordinary fume temperature control at scrap preheating procedure and fume quenching technology as developed by CISDI, for restraining the regeneration of dioxin.

Oct 30, 2017

By Y. Luo

A PC based computer model has been developed by the authors for predicting the surface subsidence due to underground coal mining. Its reliability, comprehensiveness and user friendliness demonstrate that it is a good tool for the mine operators, government agencies and scientific researchers alike.

Jan 1, 1989

By Yi Luo

Multiple-seam mining operations induce surface subsidence basins different from those caused by mining in a single coal seam, and also disturb the mining operations in the other coal seams. A computer program, CISPM-MS (Comprehensive and Integrated Subsidence Prediction Model for Multiple Seam Mining), has been developed to predict the final surface movements and deformations as well as the interactions associated with multi-seam coal mining operations. The program applies a newly developed subsurface subsidence prediction model that is able to consider the geological stratification variations. In predicting surface subsidence, the surface movements and deformations caused by the individual mining operations as well as the interactive effects are all considered. A case study is conducted in this paper for validating the program.

Jan 1, 2012

By L Y. Yang, Z Wang

This work presents the fundamental properties of CITIC magnetite concentrate and its performance in pelletising and sintering. CITIC concentrate has been widely used in pelletising to produce pellets for blast furnaces. It is also used in sintering to benefit from its sintering performance. CITIC concentrate has excellent balling properties owing to its size distribution, particle surface properties, large specific surface area and balling index, leading to strong green pellets and product pellets. When used in sintering at appropriate levels, sinter bed permeability improves, productivity is increased while coke consumption reduces, and sinter strength improves.

Nov 8, 2021

By M Warnken

Major cities are not only the focal point for AustralianÆs work, leisure and homes, they also are the focal point for the flow of resources into the built environment, motor cars and transportation and urban consumables. The steady increases in æstockÆ and waste generation, in line with GDP growth, means that cities will become the mine sites of the future if the inherent value is recovered from these materials at end of life. The urban waste stream can be characterised as containing approximately nine per cent hydrocarbon-based materials; 57 per cent biomass-based material; 28 per cent fully mineralised materials that are inert, five per cent metals and less than one per cent of problematic materials that are potentially hazardous and toxic. In order to convert these wastes into value added inputs into the economy, a number of technological interventions are required. These æurban waste mining techniquesÆ revolve around source separation and material streaming. One issue that needs to be overcome when determining which mining technique to implement, is identifying the option that will deliver optimal value, both from a financial and a sustainability perspective. The difference between embodied energy and calorific value is a case in point. Highest net resource value (HNRV) is a concept that can assist in choosing between different resource recovery options. The assessment can be done at a strategic level, or can be used to work out material specific issues. For example, used tyres can be recovered for their energy content at an approximate cost of $120 per tonne, whereas mechanical processing of used tyres can deliver a net benefit of $192.

Jan 1, 2006

The Pinto Valley, Arizona, plant of Cities Service Company is one of the newest copper producers in the United States, having started production in 1975. It is located a few miles west of Miami, Arizona, on the site of the Castle Dome Mine, a World War II operation which was shut down and its mill later moved and renamed the Copper Cities plant. The Pinto Valley concentrator uses six 18 ft (5. 5 m) diameter by 21 ft (6.4 m) long, 4000 hp, single-stage ball mills, taking crushed ore from four 7 ft (2. 13 m) standard and eight 7 ft shorthead crushers. It has a design capacity of 40,000 stpd but has higher tonnage capability for an expanded concentrator. The copper porphyry-ore is mined by two 15 yd and one 20 yd shovels (11.5 and 15.3 cu m) and is transported to the primary crusher by 150-ton trucks. The dump pocket is relatively shallow (14 ft or 4. 27 m deep); and because of the width necessary for the 150-ton trucks, it was designed to use the ore itself instead of manganese steel as an abrasion- resistant lining, although a heavy steel cap protects the dump pocket top edge. The pocket has a capacity of 300 tons of ore. Water sprays under the dumping positions direct a fog toward the truck being dumped for excellent dust control. Breaking of oversize is done by a hydraulic impact breaker mounted on a hydraulically operated articulated arm situated at the side of the dump pocket. Again because of the shallow pocket, no splitter is used to protect the spider of the 60 in. by 89 in. Traylor gyratory crusher, which is equipped with a hydroset mechanism. Crushed ore at 8 in. (203 mm) drops into the 360 st surge chamber lined with AR plate and then is fed directly to the 60 in. (1.52 m) stock- pile conveyor by an 84 in. by 20 ft (2. 13 m by 6.1 m) four-speed apron feeder at a rate of up to 4000 stph. Early in 1977, Cities Service will replace the four -speed electric drive with a hydraulic pump and motor with infinitely variable speed. They are also studying the replacement of the apron feeder with an 8 ft wide (2.44 m) belt feeder similar to those at Similkameen and Palabora. Peak crushing capacity would then be increased to 5000 stph. The AR plate in the crushed ore pocket was installed in large, rectangular sheets which required much less embedded metal to hold it in place than would the more conventional, smaller arid square pieces of cast manganese steel. For duty in the crushed ore pocket, where wear is not severe, the AR plate is a satisfactory material. The new Palabora Figure-8 crusher also uses this design.

Jan 1, 1978