Search Documents

By S. R. S. Sastri

By using the data of E.A. Hersam and F.C. Bond's equation for energy consumption in comminution, a method was developed to analyze the performance of industrial jaw crushers. The study showed that industrial jaw crushers are generally operated below capacity. The study also showed that industrial jaw crushers generally have sufficient installed power to operate at, full capacity. The method presented can be used to estimate the capacities and power requirements of jaw crushers.

Jan 1, 1995

By T. Kerr, C. Mattich, J. Wilson

"In refractory gold concentrates, gold is occluded in sulphide minerals preventing efficient cyanide leaching. Hence, roasting is used to oxidize sulphur and organic carbon, the latter being necessary to minimize recovery loss through the preg-robbing effect. In 2009, Outotec commissioned the circulating fluidized bed roaster at Syama gold mine in Mali. Since 2013 Resolute and Outotec have been implementing improvements to the roaster performance with the capacity increasing from 8000 t/month in 2013 to above 13,000 t/month in 2016, while achieving a residual sulphide sulphur and organic carbon contents of below 0.1 wt.% and 0.4 wt.%, respectively. Thus a gold recovery in the CIL of above 90% is attained. In 2016, Outotec audited the Syama roaster. The analysis resulted in the Low Carbon Roaster (LCR) upgrade concept which (i) allows re-processing of calcine dust from the spray cooler and ESP after pelletization and (ii) allows the roasting of a further fine-organic carbon rich feed, i.e. de-slime circuit tailings. The LCR upgrade aims to reduce organic carbon to <0.2 wt.% and increase roaster-leaching gold recovery by >3%. Project development included extensive testwork. The LCR process is expected to become operational during FY 2019.INTRODUCTION Double refractory sulphide ores exhibit the characteristics of gold locked within pyrite grains, in the presence of preg-robbing natural (organic) carbon. Hence, to achieve high recovery during subsequent processing steps, i.e. cyanide leaching, oxidation of sulphide sulphur is required, producing a porous calcine by way of a roasting step. This allows for the gold contained within the pyrite grains to be accessible during cyanide leaching. Furthermore, it is necessary to oxidize the organic carbon. Oxidizing the organic carbon is essential as gold recovery loss occurs as a result of gold-cyanide complexes being adsorbed on organic carbon, this phenomenon is termed as preg-robbing (Miller et al., 2016). The gold absorbed on the organic carbon is lost, reporting to the tailings stream. Hence, the aforementioned oxidation of sulphide sulphur and organic carbon is the process goal. Nonetheless, the latter must occur at a controlled temperature which is concentrate/ ore specific, since the pores of the produced calcine should not sinter, as this makes the gold contained in the calcine less accessible during leaching, leading to gold recovery loss. The tight temperature control requirement is a decisive factor in the choice of a Circulating Fluidized Bed (CFB) as the roasting reactor, due to the excellent mixing characteristics of the CFB which results in temperature homogeneity of (+/-10°C). Roasting of double refractory ores, as described above, can be included in the flowsheet after comminution and grinding, a process termed as whole ore roasting, or by including a flotation circuit termed as concentrate roasting. Roasting the flotation concentrate results in less solid flow, increased sulphide sulphur grade and organic carbon content resulting in a higher heating value and higher gold content. A typical composition of the Syama ore and concentrate is given in Table 1. Ore average values presented correspond to the period 2015, while concentrate values are typical for the flotation performance throughout the period 2012–2015."

Jan 1, 2017

By T. Krumins, F. C. Ruff, M. Eichhorn, L. Zunti

Hatch Ltd. has recently completed a project to increase refractory gold ore processing capacity at Newmont Mining Corporation’s Twin Creeks facility. The objective of the project was to increase throughput by approximately 10% by adding a third autoclave feed pump to each of the two autoclave circuits. To minimize project capital cost, autoclave feed pumps from Newmont’s decommissioned Lone Tree facility were evaluated and found to be suitable for this new service. The existing pressure oxidation circuit was reviewed in a debottlenecking study to determine other upgrades required to facilitate the increased throughput. Interruption to operations was minimized with a detailed construction plan, supplemented with detailed 3D layout model sequencing studies. The focus of this paper is project development, multi-discipline design considerations, and implementation results.

Jan 1, 2014

By N Steenkamp, L Furstenberg, W Cele, M Richter

Managing productivity and improving efficiency for a healthy return on capital employed have become key mining industry strategies under prevailing tough global market conditions. However, achieving this in a multisystem environment such as a mining operation can be daunting. The field of discrete event simulation offers some relief, giving engineering teams insight into multivariable systems and stochastic processes. It allows for integrated system thinking and domain expertise to be woven into project thinking fibre. Directed system optimisation and therefore improved efficiency becomes possible. Furthermore, capital discipline accrues from optimal upgrade investments. This paper illustrates the practical application of this approach by reviewing a typical case study for a direct shipping iron ore operation. Dynamic simulation was used to establish maximum processing plant capacity under varying material characteristics and identify capital-efficient upgrades for increasing production.The study started with descriptive statistical analysis of existing data. Discrete equipment and system capacities were defined, followed by static plant mass balance calculations to establish bottlenecks and overall static capacity. Equipment ‘uptime’ and ‘downtime’ analyses established system and overall plant availability and utilisation. From this information, a dynamic simulation model could then be developed and initially calibrated against actual plant performance to verify its robustness. Once confirmed to accurately represent existing plant dynamics, system capacity response to variable changes could be tested to ultimately determine maximum plant capacity. Additionally, plant optimisation was incorporated to arrive at optimal upgrade points. Maximum capacity and necessary upgrades were established as a function primarily of feed size distribution. Additionally, the interfacing effects of rehandling feed material to the final product grade and potentially to life-of-mine were established as important outcomes. The results of the study illustrate the value of using dynamic simulation models to realistically and cost-effectively increase throughput.CITATION:Cele, W, Furstenberg, L, Richter, M and Steenkamp, N, 2015. Capacity evaluation of iron ore processing facilities utilising dynamic simulations, in Proceedings Iron Ore 2015, pp 597–604 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Marian Radetzki

The economic developments and industrial behavior patterns that led to a lasting excess capacity in the world non-ferrous metals industries from the aid-1970s are explored. Detailed attention is devoted to analyzing and defining crucial concepts like "capacity", "excess capacity", "capacity maintenance" and "investments". Empirical evidence of capacity utilization and capacity growth in the industries under study is provided. The coincidence of excess capacity and low prices on the one hand, and investments in capacity maintenance and capacity expansion, on the other, is seen as a consequence of substantial declines in the metal industries&apos; investment and production costs during the period studied.

Jan 1, 1989

By Stig Premfors

Lamco Joint Venture is operating a Dravo Pelletizing machine to produce pellets from the natural slimes of an earthy hematite ore. The grate area of the machine 3.3 x 106 m equal to 350 m2 (3800 sq. ft.) and the installed fan capacity is 8200 HP. The limiting factor for production is normally fan capacity. This means that the processing fans can not pull the additional air (i.e the additional calories or BTUs) through the bed which would be required for increased production. A way to increase production without major modifications is to supply the additional calories needed for increase production by adding coal to the pellet feed. After successful laboratory tests following method of coal addition has been chosen and the following results have been obtained. 1. The ground coal is added to the slurry prior to the filters and the rotary dryer. 2. By adding 0.6% coal, an increase of about 15% in production rate has been obtained. 3. No significant changes of metallurgical properties have been observed (i.e. tumbler index, compressive strength, ferrous iron content, reducibility, Linder degradation and swelling). 4. No unexpected operation problems have been experienced. The pellet discharge temperature increases and is the limit for how much production can be increased by coal addition without making plant modifications.

Jan 1, 1971

Mining of copper ore is still the most important business in Chile. In order to mine ore with a copper content of less than one percent at Minera Los Pelambres in an economical way, opencast mining is mandatory. Due to the prevalence of avalanches at the mine, the concentrator was located in a stable area, some distance from the mine. As a consequence, the material has to be transported between mine and concentrator by conveyor. A downhill conveyor system has been implemented for more than ten years as the most suitable and most economical ore transport alternative. Due to the length (12.6 km) and inclination (1300 m drop) of the conveyor system, the stresses in the steel cord belt are the dominant design criterion, resulting in a belt quality of ST 7800. Additional dynamic belt stresses during transient operating conditions are avoided by the installation of high capacity adjustable frequency drives. The rating of a single drive unit is 2500 kW. During ten years of operation, several capacity increases have been implemented, from an initial 5800 t/h up to the current capacity of 9900 t/h. This presentation describes the engineering challenges of the implementation of the world&apos;s strongest belt conveyor system. Capacity increase measures like the development of new control and breaking strategy, proved by dynamic simulation of belt forces and belt speed scenarios are explained. During this long-term partnership of RWE Power International, the former Rheinbraun Engineering, with Minera Los Pelambres, RWE has been engaged continuously for development work, safety checks, expert opinions and maintenance audits, and giving new impulse to conveyor technology.

May 1, 2010

By S. Sarioglan

The bleaching of edible oils, industrial oils, and some chemicals may be achieved using natural and acid-activated clays. These materials remove impurities and pigments from the oils. In this work, a bentonite clay from Turkey (Somas bentonite) was activated with different concentration of H2SO4 and HCl at 70~90°C and 5~8 hours. Under these conditions several cations were removed from natural bentonite (Al, Mg, and Fe) and DTA-TGA, FT-IR curves of the solids obtained after acid treatment were examined. Treatment time and acid concentration increased the degree of destruction of the bentonite structure which was determined by ICP. Activated samples were tested in order to verify their capacity to bleach soybean oil and compared to standard commercial bleaching clays. The experimental results indicate that treated samples with H2SO4 have the same efficient in bleaching crude soybean oil with the standards and treated sample with HCl is more efficient in bleaching than the commercial products.

Jan 1, 2014

By Mohab Sabry

Pile foundations are used extensively around the world to support both inland and offshore structures, including important structures such as nuclear plants and oil drilling platforms. The limit of the pile depth is currently predicted during the pile deriving process, given no chance for the designer to predict accurately the capacity of these piles prior installation. Furthermore, after pile installation, designer may not be able to modify the pile group design by increasing the number of piles and or changing the geometry of the pile group. This paper presents a numerical model for the case of single piles driven in homogenous sand using finite element technique and the theory of cavity expansion. The model is capable of simulating all the construction stages of concrete piles up to the maximum depth, which can be driven in sand and accordingly the capacity, which can be attained by these piles. The program "PLAXIS" is used to perform the proposed analysis. This model simulates the process of pile driving in terms of the changes in the earth pressure and the overconsolidation ratio acting along the pile&apos;s shaft. Based on the results of the present investigation, these depths can be predicted based on the pile geometry and the sand properties. Charts are given to provide these depths for given pile/soil conditions.

Jan 1, 2006

By H. M. von Seebach, M. P. Trubeljal, L. G. Austin

Six US coals and a crystalline quartz were tested in an instrumented laboratory high-pressure grinding rolls machine equipped with 100-mm-diam. rolls. The machine was choke-fed to maximize the capacity. As expected, the specific capacity decreased with increased grinding pressure for each material tested. Among the six coals, there were significant differences in the critical angle of nip, the effective feed porosity and the variation of strain at the gap relative to the grinding pressure. Although a precise correlation was not obtained, the overall effect of these factors was that, at a given grinding pressure, the specific capacity increased as the Hardgrove grindability index of the coal increased. The relationship between the specific capacity and the grinding pressure for a given coal was independent of feed size down to 150 µm. However, smaller feed sizes produced anomalous results, and the flow within the feed hopper was restricted.

Jan 1, 1996

By Howard A. Perko, Melinda J. Hummel

"Hydraulically jacked piles, herein referred to as jacked piles, are commonly used for underpinning existing structures to arrest settlement or augment an existing foundation for higher loads. They consist of steel pipe segments coupled together and jacked into the ground using a hydraulic ram. Pipe sections can vary in size from 3"" diameter to 18"" diameter or larger. Jacking resistance is typically provided by dead loads of existing structures. This type of piling system has been utilized for foundation underpinning, repair, and augmentation for more than 120 years, yet little has been published on the capacity, installation standards, and reliability of these systems. Pile load tests from a number of projects are presented and analysed. The data show that previous methods of jacked pile capacity and depth prediction are crude at best. Empirical relationships between capacity, depth, soil type, and standard penetration resistance blow count contain a high degree of scatter. Scatter in the data indicate capacity prediction for jacked piles needs further research and refinement.INTRODUCTIONPush pier, resistance pile, steel pier, and jacked pile are some of the names often applied to hydraulically jacked piles used for underpinning. The term ‘jacked pile’ is more common in building codes and will be used herein. Although jacked piles can be installed for new construction, this paper is focused on piles used for support of existing structures.Jacked piles consist of short segments of pipe or structural steel tube that are coupled together and forced into the ground using a hydraulic ram fastened to or beneath a footing, stem wall, or grade beam of an existing structure. In this way, the weight of the structure provides the resistance necessary to force the pile into the ground. A factor of safety can be achieved in design by redundancy, which is consecutively installing more than one jacked pile to support the same portion of foundation. Installing jacked piles consecutively using the same dead load and then releasing the load after each pile installation allows one to continue adding piles to the same general area until a total aggregate capacity is achieved to account for anticipated dead plus live loads and a desired factor of safety for that area.An engineering schematic of an example jacked pile connected to a footing foundation is shown in Figure 1. Modern jacked piles typically incorporate a steel bracket. There are many sizes and styles of brackets available. Some categories include plate brackets that bolt to the outside of an existing foundation wall, wide and narrow angle brackets that extend under existing footings, pin brackets for attachment to structural steel, and reverse angle brackets for attachment to footing and wall. Table 1 lists example brackets and their benefits."

Jan 1, 2017

By S. X. Liang

In China, the bearing capacity predictions of the pile with Stress-Wave Theory have been developed rapidly in recent years. This paper recommended a DZH-3 Pile Driving Analyzer and its relevant computer programs. Taking Qinghai Hotel Project for example, it gave their applications in the dynamic tests of large diameter cast-in-place piles.

Jan 1, 2010

By M. Mets

Pile foundations have been used in Estonia since the beginning of 1960&apos;s. To evaluate the capacity of piles nearly 2,500 pile tests and 1,800 pile loading tests Have been carried out. The pile foundations of nearly 150 houses are under settlement observations.

Jan 1, 2000

By J. Wennerstrand

Slender steel piles have found an increased use in Sweden in resent years. These piles are often driven throw soft normally consolidated clay to refusal in till or at the rock surface. In contrast to most other piles the bearing capacity with regard to failure of the shaft is in many cases smaller than the bearing capacity with regard to failure of the soil or rock at the lower end of the pile. Imperfections such as deviations from a straight line of the pile centerline and residual stresses in rolled and welded profiles are important for the capacity of the pile shaft. Even thow the second order moment caused by initial deviations in piles is only half of that in a column with the same slenderness, imperfections can and should be accounted for in much the same way as for columns.

Jan 1, 1989

By Fábio Heiji Yamada, Marcelo Koiti Fugihara, Ruano Fonseca Araujo

Conception the simulation and optimization technologies for industrial processes applied in the mining environment: tools and methodologies. Clarifications provided about the differences of these techniques when compared with static analysis (intuition, use of static spreadsheets, etc.). Presentation of practical cases at several big mining companies in Brazil. These projects will be presented and illustrated through dynamic simulation models developed at those companies, each one with its set of objectives, scope and results (for example: sizing the number of equipment, silo, piles related to the mining processing, logistics, ROM transportation, mine operations plan, etc.).

Oct 3, 2019

By Emad Farouz

This paper compares the predicted axial capacity of driven Pre-cast Pre-stressed Concrete (PPC) piles for the Lake Gaston Water Treatment Plant (LGWTP) using several design methodologies versus the axial capacity measured from dynamic and static load testing. The LGWTP site is located in Chesapeake, Virginia and is part of the Great Dismal Swamp. The subsurface investigation included soil borings, in-situ dilatometer (DMT) tests, and in-situ piezocone (CPTu) tests. The axial capacity predictions of the PPC piles were performed using the computer programs DRIVEN and FB-DEEP which are based on SPT N-values. Additionally, an empirical method proposed by Martin, et al. (1987) based on local experience with PPC pile design in the Yorktown formation in the Tidewater area of Virginia was also evaluated. Finally, the ?Laboratoire Central des Ponts et Chausées (LCPC)? method developed by Bustamante and Gianeselli (1982) based on CPT measurements was also used to develop the axial pile capacity of the piles. This paper shows that the FB-DEEP computer program and the LCPC method provided a reasonably good prediction of the pile axial capacity measured from PDA, CAPWAP, and Static Load Tests in comparison with the other design methods used. The soils in this area develop significant setup over time and it was found that FB-DEEP and the LCPC method are capable of incorporating this setup in the prediction of the long-term axial capacity of driven piles in this area.

Jan 1, 2007

By Nahiri Hirsh

El programa de fortalecimiento de capacidades Capas y Capaces impulsa el trabajo articulado de las instituciones educativas Nuestra Señora de La Merced, Rafael Loayza Guevara y Dos de Mayo, organizaciones de base, Yanacocha y la Dirección Regional de Educación, para el desarrollo sostenible de las comunidades. Se trabaja en el desarrollo y mejora de capacidades técnicas en estudiantes de 3°, 4° y 5° año de secundaria, así como de padres y madres de Cajamarca, con el objetivo de prepararlos para la vida y desterrar la dependencia económica. La capacitación se realiza con métodos innovadores (haciendo uso de laboratorios, equipos y maquinaria moderna) que han logrado convertir al programa en referente del Ministerio de Educación para la educación técnica en instituciones públicas a nivel nacional.

Sep 20, 2019

By J. G. Martin, J. C. Campbell

THE VICTORIA JUNCTION 31,4-million-ton coal preparation complex went into operation in October 1976."' It is designed to produce a metallurgical coking coal by lowering the sulphur and ash content of the raw coal using a heavy-media cycloning process to treat deslimed crushed coal, with scavenging of fine coal by flotation from the primary minus-28-mesh screen product. A secondary H-M cyclone scavenges a thermal-grade coal from the primary H-M cyclone tailing.

Jan 1, 1985

By Dan Currie, Tom Lamb, J. Coady Marsh, Gary Landry

"This paper describes the Cape Breton Development Corporation&apos;s experience with the Lovat M-300 tunnel-boring machine at the Donkin-Morien Mine. Between January 3 and December 21, 1984, the 7.6 m (25 It) diameter TBM advanced 3350 m (10 990 ft) . The authors will describe experiences with the machine and highlight the implications of tunnelling machines to underground coal mine development in Canada. IntroductionThe Cape Breton Development Corporation (CBDC) has recently completed the drivage of a 7.6 m (25 ft) diameter tunnel, 3.5 km (2.2 miles) in length , to access the Harbour Coal Seam at the Donkin-Morien Project. The tunnel was successfully driven with the first Canadian rock tunnel-boring machine (RTBM or TBM), designed and built by Lovat Tunnel Equipment, Inc. The initial mine development consists of the drivage of two tunnels to the first major coal seam. Future plans are proposed for the development of a 4 million tonne-per-year mine (Marsh et al., 1983, Gillman, 1982), which will require the drivage of a further two tunnels and could access up to four coal seams. The tunnel cross-sectional areas were designed to provide sufficient ventilation area and access for a production of 4 million tonnes per year."

Jan 1, 1986

By J. Kochhar, Robert G. Cooper

"The Cape Breton Development Corporation is a federal Crown corporation which was formed in 1968. Initially, the Corporation had two divisions - the Industrial Development Division, whose purpose was to stimulate Cape Breton Island&apos;s economy, and the Coal Division with a mandate to phase out the operating coal mines. However, that strategy changed in the early 1970s with the Middle East oil crisis. As a result of that crisis, Nova Scotia Power Corporation adopted an ""off oil"" policy. Today, approximately 700/0 of Nova Scotia power needs are met by generation of electricity from coal. Therefore, since the early 1970s, emphasis has been on the rehabilitation of the Cape Breton coal mining business with the opening of three new mines.Today, Devco is solely a coal mining company which employs 3300 people.Physical DescriptionThe mines operate in the Sydney coal field which is located on the eastern tip of Cape Breton. The Corporation leases the deposit from the province of Nova Scotia and its leases cover all coal from the outcrop to the 4000 ft depth. The seams outcrop along the shoreline and dip beneath the ocean floor at dips varying between 5% and 100%.There are eleven seams, of which three - the Harbour, Phalen, and Hub - have been extensively mined."

Jan 1, 1990