Search Documents

By Henry Sturgis Drinker, Rossiter W. Raymond

Jan 1, 1914

By W. H. Andrews

The constantly increasing consumption of Portland cement in the State makes the above subject of particular interest at this time. The increasing demand is due to the rapid settling of the country and the fact that new uses are being found frequently for the above named commercial article. The industry is one that is bound to grow as the population increases, and this being the case it may be well at this time to consider briefly the matter of the chemical and physical composition of proper raw materials. A cement mixture is one that contains approximately 75 per cent, carbonate of lime, 15 per cent. silica, and 5 to 7 per cent. alumina and iron oxides; the other elements being magnesium carbonate and mall quantities of the rarer elements generally associated with limestone deposits. It can be readily seen from the above composition that it is possible to build up this mixture from a number of different materials. First.—A rock high in carbonate of lime can be mixed with clay or shale in such proportions as to bring about the desired composition ; the chief difficulty in the building up of such a mixture is that it is hard to find a clay or shale in which the silica-alumina ratio lies between 4 to 1 and 3 to 1 and at the same time shows physical characteristics which will make certain its adaptability to the practical manufacture of Portland cement. Very often clays or shales are found which are right chemically but contain large quantities of grit or free silica. Such clays or shale must be ground to extreme fineness in the mixture in order to make the silica and alumina combine with the lime when the mixture is burned. On the other hand, clays or hales are often found that have the proper physical characteristics but in which the amount of alumina is too great. Second.—A mixture can be built up of different limestones some of which run above the 75 per cent. requirement and others below;

Jan 1, 1914

By Ralph Hayden

PAGE I. IntRoduction........239 II. Definition of Anaconda SLime....240 III. The Source of Slime......240 Remodeled Flow Sheet......240 Old Plow Sheet,.......242 IV. ConStitution of Slimes......243 Chemical........243 Physical.........243 V. The Slime Problem.......247 VI. THe Experimental Slime Plant....248 VII. Slime Thickeners. ETc .......249 Slime Ponds........249 Tanks.........249 Comparative Efficiency of Open and Baffle Tanks .260 Callow Tanks........252 Kuchs-Laist Centrifugal Separator....253 Garred Filter........256 Dorr Continuous Thickener.....256 VIII. Concentrators........257 Round Table........558 Peck Centrifugal Concentrator....259 Competitive Tests.......260 Twenty-Deck Round Table..... 260 Slime Feed Distributor......261 IX. ConcluSion.........262 I. Introduction. In the wet concentration of ores there is always a certain amount of very fine material with which to contend. and which invariably carries such quantities of value that the treatment of it is worth while. commercially. This fine material usually contains that portion of the ore which hinders the separation of the mineral values: namely. the colloidal material resulting from the decomposition of certain constituents of the ore. The object of this paper is to show what efforts have been made to solve the slime problem as it occurs in the concentrator of the Washoe

Jan 1, 1914

By Edgar M. Dunn

Part I. Determination oF Gases in Smelter Flues. General considerations. Regular methods for carbon monoxide, oxygen, nitrogen, moisture. Sulphur oxides-—Methods of Lunge and Hempel tried, and either modified or discarded, with reasons therefor. Gravimetric method developed at Anaconda. Description of apparatus used. Brief notes on Richter and Hawley methods for the direct cietermination of sulphur trioxide. Carbon dioxide, with complete notes on same. Arsenic trioxide. Table of percentages of flue gas constituents found at a Western smelter. Some final notations as to the value of flue gas analysis, in connection with an intelligent log of furnace operations. Part II. Notes on the Determination oF Dust Losses at the Washoe Reduction Works, Anaconda, Mont. Discussion of problem, with description of flue system. Various places and methods for determinations of velocity. Instruments used. Procedure in making determinations for velocity. Soundings of cross-section for depths of dust. Calculation of velocities and areas. Daily volume of gas, and plant operations during tests. Place for dust determinations. Apparatus and methods of 'sampling. Results obtained, with table of daily amount of dust losses. Analysis of dusts for values, from various sampling stations. Complete analysis of composite sample of stack emanation. Last analysis totaled to show form in which present. Discussion of recovery as a commercial proposition. References on Pitot tube and calculations.

Jan 1, 1914

By E. P. Mathewson

In a discussion of a paper on The Basic Process as Applied to Copper Smelting, by Percy C. Gilchrist, read before the Society of Chemical Industry, London, Jan. 5, 1891,' Prof. W. C. Roberts-Austen asked Mr. Gilchrist whether he thought that the substitution of a basic lining for acid lining in the Manhks process would afford anything like the service which it had been shown to render in the metallurgy of iron. Claude Vautin stated that he had experimented for over two years. with basic linings for Bessemer converters for copper mattes at Cobar, but had given up the attempt on the score of cost. Mr. Gilchrist in his reply stated that he did not believe in applying any system of Bessemerizing to copper. About the time of the presentation of the paper mentioned,Hermann Keller, Superintendent of the Parrot smelter, in Butte, was experimenting on a large scale with converters lined with magnesite brick. He gave up the idea on account of the cost of linings and because no particular advantage was observed. My belief is that his tuyeres and converters were too small. A short time afterward similar experiments were tried at the Great Falls plant of the Boston & Montana Co., and at the Old Works of the Anaconda Copper Mining Co. in Anaconda. These were abandoned on the score of cost and the lack of advantages. The same cause of failure, in my opinion, holds here. The Anaconda Copper Mining Co., however, adopted the magnesite brick lining for its tilting casting machines. Fig. 1 is a view of the first tilting furnace casting copper. It was made from an old Brueckner roasting cylinder. Fig. 2 shows an elevation and vertical and horizontal longitudinal sections of the second tilting furnace, built in 1897.

Jan 1, 1914

By Archer E. Wheeler, Milo W. Krejci

The Boston & Montana Reduction Works at Great Falls, Mont., was formerly the reduction works of the Boston & Montana Consolidated Copper & Silver Mining Co., and continued as the reduction plant for the independent company until June 1, 1910, when the consolidation of a large number of the operating companies of Butte was effected. It then became merged in the Anaconda Copper Mining Co. as the Boston & Montana Reduction Department of the Anaconda Copper Mining Co. The history of copper converting at this plant, while not covering the entire period of the commercial use of the process in this country, does cover by far the larger part of it, and as the operation of and appliances for the process have undergone many changes during the time, it may, perhaps, be of some interest to put the record of these changes into permanent form. The plan followed in the preparation of this paper has been to give first a brief chronological record of the principal events and changes and then, even at the risk of some repetitions, to give more detaild accounts of some of these changes under separate headings. The headings for the complete paper are as follows: 1. General. Chronological Review. 10. Development of Different Classes 2. Mechanical Manipulation. of Converters After Class I. 3. Casting of Finished Copper. 11. Basic Lining. 4. Tamping of Linings. 12. Number and Size of Tuyeres. 5. Early Acid Linings. 13. Cast Copper Tuyeres. 6. Acid Linings With the Use of Ore. 14. Efficiency of Air. 7. Introduction of Flux Through the 15. Size of Converter Mouth. Tuyeres. 16. Height of Converter. 8. Bottom Blast. 17. Summary. 9. Disposal of Converter Slag, General Chronological Review. Ground was broken for the general concentrating and smelting plant in the spring of 1,891. The first departments to start operations were the concentrator in March, 1892, and the Brückner roasting and reverbera-tory smelting departments in April, 1892. The converter department

Jan 1, 1914

By Robert Franke

In view of the prominence which the conical mill has attained in the fine-crushing field within the few years since its introduction, the following comparison with its more mature forerunner, the Chilean mill, based on extensive tests, is submitted in the interest of the milling profession. Soon after designing the concentrating plant of the Miami Copper Co. in 1909, the Hardinge conical mill made its appearance in the milling forum. Its possibility as a suitable crushing device for the plant was well recognized, but in view of the lack of commercial demonstration, at the time, as to capacity, efficiency for desired product, and the still more uncertain factors of cost of maintenance and power consumption, it was deemed that the immediate adoption of this machine throughout the plant would be a hazardous undertaking. For these reasons it was decided to equip the majority of the immediately required units of the plant with Chilean mills, the fine-crushing proficiencies of which were better known, and one section with Hardinge mills, to serve as a test unit for the guidance of future installations and replacements. Thereby, after 1.5 years' operation with both types of mills, a thorough test as to metallurgical efficiency and cost economy has been obtained. The conical mill used in these tests is the 8-ft. Hardinge pebble mill, having a cylinder 22 in. in length. The cylindrical portion of this mill is lined with cast-iron liner plates, and the conical extensions with silex bricks bound together by cement. Each liner plate carries a projecting lifter, the function of which is to increase the height of drop of the lifted material. Danish No. 5 pebbles, obtained from the coast deposits of Denmark, are used for the grinding charge. The Chilean mill used is a fast-running, 3-roller, 6-ft. Saturn mill, with screens of 0.037-in. opening. The feed to these mills is the oversize of Callow screens having 0.029-in. openings, which follow rolls crushing to 0.5 in. For the ore of this mine, a moderately hard but very fissile schist,

Jan 1, 1914

By Max Hebgen

I. Natural Features of State Affecting Power Development .. 792 II. Early Developments. 1. Big Hole Plant................. 792 2. Canyon Feny Plant............... 793 3. Madison Plant No. 1............... 593 4. Black Eagle Plant................ 795 III. Later Developments. 1. Madison River System .............. 795 2. Missouri River System.............. 797 3. Great Falls System............... 797 4. Missoula River Development............ 797 5. Big Fork Development.............. 802 $ IV. Present Capacity of Power Developments....... 802 V. Transmission System...............: . 802 VI. Character of Load. 1. Lighting and Small Power Uses........... 804 2. Street Railways ................ 804 3. Mining................... 804 4. Railroads.................... 808 5. Irrigation................... 810 VII. Operation of System................. 812 VIII. Increase in Use of Power............... 811 IX. New Power Developments............... 814 X. Undeveloped Powers................. 815 It is estimated that the total stationary power now used in the United States. steam. water and gas. is probably over 30.000.000 h. p. The total developed water power is about 6.000.000 h. p. The water power in the United States now economically capable of development probably exceeds 25.000.000 h. p. The total developed and undeveloped power is

Jan 1, 1914

By Frank R. Corwin, Selden S. Rodgers

PAGE I. Introduction,........... 383 11. Brief History of Present MacDoUgall Plant,.... 384 III. First Experimental Work on Increasing Capacity of Furnaces, 385 IV. Effect On MacDouRall Plant of IncreaBed Draft from New Smelter Stack,,.......... V. Increasing the Capacity of the MacDouGall FurnaceS,.. 391 (A). Test of Arthur Crowfoot on Increasing Capacity,.... (a). Description of Test,........ (6). Discussion of Results Obtained from Test,... 393 (B). Investigation Carried Out by John A. Church, Jr.,... 395 (a). Advantages of High Speed,......398 (C). Effect on Regular Operation of Department by Applying Results Obtained from Experimental Work ..... 399 (D). Fundamental Principles Involved in Increasing the Tonnage, . 400 VI. Treatment of an INcreased Amount of Ore Screenings,.. 401 VII. Maximum Percentage oF Ore Screenings in a MacDoUGall Feed, 403 VIII. Tests to Further Increase Capacity of Furnaces,... 406 IX. Tests to Decrease PercentaGe of Flue Dust made by MacDouGall Furnaces,............. (A). Repath-Marcy Furnace......... 408 (B). Modified Hepath-Marcy Furnace,....... (C). Crouse Furnace Designed for Dust Prevention,.... 413 (a). Tests on Crouse Furnace,....... X. Concrete Hearths,.......... 419 XI. Conclusion,............ I. Introduction. Since the first installation of MacDougall roasters at the Great Falls smelter of the Anaconda Copper Mining Co., the capacity of the furnaces.has been more than doubled. During the first nine or ten years of the operation of the MacDougall department the tonnage treated by the furnaces remained practically unchanged. Experimental work carried out in 1906, however, showed that increasing the draft of the furnaces would bring about an increase in capacity. In 1909 the MacDougall department was connected to the new smelter stack and

Jan 1, 1914

By Ralph Nichols

The mines are near the town of Gilmore, in the Texas mining district. This district was organized in 1880. The present producing mines are near the terminus of the Gilmore & Pittsburg railroad. This railroad connects with the main line of the Oregon Short Line at Armstead, Mont. The distance from Gilmore to Armstead is 70 miles. The town of Gilmore is near the head of the Lemhi river at an elevation of 7,000 ft., while the mines are from 400 to 1,300 ft. higher. The range of mountains upon which the mines are situated forms the water shed for the Little Lost river on the west and the Lemhi river on the east. The winters are severe and the snow fall is heavy, but the mines ship right through the year. There is an abundance of timber suitable for all mining purposes in the immediate vicinity. Water is piped into the camp from a lake about 2.5 miles distant. This lake is about 1,400 ft. above the town of Gilmore. The water is exceptionally good for boiler and domestic purposes. The mining companies now producing are the Pittsburg Idaho Co., Ltd.; the Latest Out Mining & Smelting Co., Ltd.; and the Oilmore Mining Co., Ltd. Besides the above propertiea, there are a number of prospects in different stages of development. The producing mines of the district are fissures in limestone, with a general northeast-southwest course and a dip to the west of from 40' to 70°. These fissures are at about right angles to the bedding of the limestones. The veins are regular and the ore shoots strong, both laterally and in depth, so far as developed. The ore shoots have a rake or pitch to the south. The character of the formation is shown in Fig. 1, a section of the Latest Out mine. Character of Ore. The ores of the district are oxidized, carrying an excess of iron over the silica (insoluble matter). The vein filling is a mixture of limonite and hematite, which is replaced by shoots of lead-silver ores. The lead minerals consist of carbonate of lead principally, but with small quantities of sulphide, sulphate, and other lead minerals.

Jan 1, 1914

By C. A. Mitke

During September, 1911, the fire area in the Lowell mine continually increased and gases resulting from the fire came through the upcast shaft. These gases contained such a large percentage of sulphur dioxide that the men were unable to go up and down on cages, and, within a comparatively short time, repairs in the shaft mere found to be necessary. Since the fire was in sulphide ores and extended into certain timbered sections, the gases contained varying amounts of SO2, CO2, and perhaps, at times, CO. The temperature in the shaft was generally about 97", and the relative humidity from 97 to 99.5 per cent. The corrosive action of the fumes became apparent when the cables had to be changed more often than usual, the heads of lag screws in the guides of the shaft disappeared, and the cages needed frequent repairs. It also became necessary to repair two compartments of the shaft by putting in 150 ft. of new guides between the 600 and 800 levels and lag screws in nearly all the old guides from the surface to the 800 level. 2. Ordinary Methods of Testing Helmets which were Unsatisfactory. These conditions required all work to be done by men wearing oxygen helmets. The Draeger type was tried, and was used until all repairs were completed. At first the helmets were tested for air circulation and air tightness and the injector mas tested by water gauge according to the methods recommended by the Draeger Oxygen Apparatus Co. Six arrangements, covering these different tests, are illustrated in the catalogue and circulars of the company. After the above tests had been made on the oxygen apparatus, the men still complained about leaky helmets. Small quantities of gas entered the helmets and could not be detected by these methods. The

Jan 1, 1914

By M. H. Gidel, D. C. Bard

These notes are based on the megascopic study of a suite of 2,400 specimens of minerals and ores from the Butte mines, combined with field observations at intervals over a period of several years. The estimate of average vein composition is based on field acquaintance with the veins. It is probably correct in its broader proportions, and should be of use for comparison. Chemical and Mineral Composition of Unoxidized Vein Matter. Per Cent. Oxygen,......48.00—Quartz, rhodonite, rhodochrosite, sericite, kaolinite, barite, calcite, and hübnerite. Silicon,...... 36.O0—Quartz, rhodonite, sericite, kaolinite, and willemite (very rare). Sulphur,.....5.0—Sulphides of iron, zinc, copper, lead, and sulphates of barium and rarely calcium. Iron,.......5.00—Ferric sulphides (pyrite, bornite, chalcopyrite), also in sphalerite, tetrahedrite, and rarely hematite and siderite. Manganese,.... 2.00—Rhodonite, rhodochrosite, and hübnerite. Zinc,.......1.00—Sphalerite, very rare wurtzite and willemite, and tetrahedrite and tennantite. Carbon,......0.50—Rhodochrosite and calcite. Capper,......0.75—Cuprous ( + ) and cupric (—) sulphides. Aluminum,.... 0.50—Sericite and kaolinite. Hydrogen,.... 0.50—Water, sericite, and kaolinite. Potassium,.....0.20—hicite. Lead,....... 0.20—Galena. Arsenic,......0.10—Tennantite and enargite. Barium,......0.10—Barite. Calcium,.....0.10—Fluorite, calcite, and rare gypsum. Antimony,.... 0.02—Tetrahedrite, famatinite, and silver sulphantimonites. Fluorine,.....0.05—Fluorite. Silver,.....1 —Argentite, and sulphantimonites. Tungsten,.... —Hübnerite. Phosphorus, • —Wavellite. Bismuth,' .... 0.05—Sulphide (?) Tellurium,... 1 —Telluride (?) Selenium,.... —Selenide (?) Cadmium,.... —Sulphide (?) Gold,..... —Native and telluride (?)

Jan 1, 1914

By H. T. Van Ells

The following is a brief description of the cost accounts in effect at the mines of the Anaconda Copper Mining Co. The accompanying chart, Table I., shows the distribution of labor, materials, and redistributable accounts to the various operating and repair accounts. OperatiNG. Development. Owing to the fact that every mine has its peculiarities in formation and methods, the question of arriving at what charges should be included under the head of " Development" is one that has occasioned considerable thought and comment, and in the cost sheet of the Anaconda Copper Mining Co. this account has been sub-divided to show the expenses of breaking ground, tramming, timbering, shaft sinking, up-raising, and cutting stations and skip chutes. It has always been the policy of the company to charge the entire cost of this work to operations monthly, whether the mines are producing or not, also the cost of the opening up of new mines; and only surface construction and additions are charged to capital, excepting original machinery installed for operating pumping plants. Explanations of the charges to the various sub-accounts follow : Breaking Ground.—Work performed in driving cross-cuts from the station, or cross-cuts from the drifts, and diamond-drill work, for the purpose of discovering or developing ore bodies. Tramming.—Cost of tramming waste produced by cross-cuts mentioned above. When waste is hoisted to another level to be used for filling, the charge to this account stops at the station, and when hoisted to surface the charge includes tramming from the collar of the shaft to the dump. Timbering.—Cost of timbering the cross-cuts mentioned above includes the cost of handling and framing such timbers, but does not include the wages of station tenders and top carmen.

Jan 1, 1914

By Archer E. Wheeler, Milo W. Krejci

There are two general methods in use for the production of metallic copper from matte which are worthy of consideration : (1) the Welsh blister process, and (2) the converter process.' As practically all of the copper produced to-day is made in converters, we will give a brief outline of that process before proceeding with the special subject of this paper. Matte may be roughly defined as a mixture of the sulphides of copper, iron, nickel, silver, etc. In the converter process this is blown up to metallic copper in a modified type of Bessemer converter. The conversion of matte consists mainly in, (1) the removal of sulphur in the form of SO2, and (2) the slagging of the iron. With this brief statement we come to the two subdivisions of the process of converting mattes: Converting with acid linings. Converting with basic linings. Converting with Acid Lininys, This is carried out by lining the converter with siliceous rock or ore, which performs two functions: It protects the iron shell of the converter from the molten charge, and it furnishes the silica for combining with the iron as it is oxidized from the matte, to form a ferrous silicate. It follows from the second of these functions that this siliceous lining must be replaced from time to time, and in practice it has been necessary to reline converters every 8 to 40 hr., this time varying in different plants and even with different linings in the same plant, the life of a lining depending upon the grade of the matte treated, and upon the composition, the thickness, the tamping, and the drying of the lining.

Jan 1, 1914

By W. T. Burns

Attempts were made in 1908, at the Great Falls Works, to produce ingots direct from the Butte precipitate by smelting the material in a reverberatory refining furnace. The ingots produced in this manner averaged 99.4 per cent. of copper and 0.40 per cent. of arsenic and antimony. The copper content being considered too low, it was decided to cast the copper into anodes and to treat the anodes in the electrolytic plant. No. 1 Furnace, in which the precipitate was treated, was a regular cathode refining furnace previously employed in making wire bar, cake, and ingot from electrolytic cathodes. The hearth of the furnace was 24 by 12 ft., having a capacity of 100,000 lb. of cathodes. The furnace was coal fired, and the copper was dipped by means of trolley ladles. The average composition of the furnace charges was as follows: Per Cent. Peer Cent. Copper. Precipitate,..........7.5.3 40 to 80 Purification cathodes,.....1.9 92 Refinery slag (oxide slag),.. 10.1 50 to 60 Electrolytic cathodes,... 2.1 99.9 Precipitate anode scrap,.... 3.1 99.0 Scrap copper,.........7.5 99.2 100.0 The slag from this furnace amounted to 46 per cent. of the total amount charged and was of the following average composition: Per Cent. Cu..............16.86 SiO2.............34.7 FeO.............18.8 A12O3.............13.0 CaO.............9.4 MgO.............2.7 S............... 0.47 As..............0.11 Sb...............0.006 Ag, oz per ton.....0.18

Jan 1, 1914

By Willis T. Burns

I. Introduction.......................................... 703 II. History................................................ 703 III. General Description of Plant......................... 704 IV. AnoDes................................................. 711 V. Cathodes............................................... 714 VI. Electrolyte............................................ 718 VII. Electrolytic Slime..................................... 727 VIII. Power................................................. 728 IX. Operating Details..................................... 732 X. Furnace Refining...................................... 736 XI. Physical Testing oF Products.......................... 739 I. Introduction. These notes are submitted, not as a discussion of the modern practice of electrolytic-copper refining, but as the record of a refinery that was among the pioneers in the field and that is to-day, and has been for 17 years, operating under conditions not to be found in any similar plant in the country. I refer to the current density, which is at least 60 per cent. higher than that regularly employed elsewhere, and to the fact that the anodes treated are the direct product of the converter rather than of the reverberatory furnace. The writer has no knowledge of any other refinery treating anodes of this character. II. History. This refinery, now one of the oldest plants of its kind operating in this country, was built in 1892 by the Boston & Montana Consolidated Copper & Silver Mining CO. to refine the product of its Great Falls reduction works. The estimated capacity of the plant as designed was 65,000 lb. of cathodes per day at a current density of 16 amperes per square foot.

Jan 1, 1914

By Earl S. Bardwell

The structural relations existing between cuprous oxide and copper were first systematically studied by Heynl; who suggested that a study of the microstructure of refined copper might be substituted for the analytical methods in vogue for determining the oxygen content of copper coming from the refining furnace. Hofman, Green and Yerxa,2 in their paper A Laboratory Study of the Stages in the Refining of Copper, working along the lines suggested by Heyn, showed that a study of the microstructure could be made to yield a correct estimate of the oxygen content of refined copper. In order to determine the oxygen content of the specimen of refined copper under examination a photomicrograph was first made. From the relative areas of copper and eutectic, the percentage of cuprous oxide and the corresponding percentage of oxygen were then readily calculated. It was found that the values for oxygen thus obtained corresponded closely with the analytical results. With the idea of utilizing this method of determining the oxygen content of each charge dipped from the refining furnaces at the Boston & Montana Reduction Plant, the physical testing laboratory was equipped with suitable apparatus for carrying out the work. It may be of interest to describe certain of the methods which have been worked out in this connection and give such data as have been obtained bearing on the effect of the oxygen content of refined copper upon its conductivity. Apparatus.—For the benefit of those who may be unfamiliar with metallographical apparatus and methods and may be interested to know what equipment is required, a few words with regard to the apparatus are in place at this point.

Jan 1, 1914

By A. Eilers

A number of the copper refineries in this country have lately separated some of the rarer metals from the slimes in the refinery tanks. One of these has furnished me the following table of recoveries from given amounts of blister. I publish this to show the proportions, to gold and silver and to each other, in which these rarer metals may be expected to occur in copper from certain localities. GarFIeld, Utah :—The blister copper comes principally from the Bingham porphyry copper mines. Steptoe, Nev. :—All the blister copper is produced from the Nevada Consolidated mines. (Also porphyry deposits.) Omaha, Neb. :—Blister copper comes principally from concentrated copper-lead mattes shipped from the different lead-silver plants of the Rocky Mountain region to the converters at the Omaha lead refinery. Mountain, Cal. :—Ores occur in connection with diorite (?).

Jan 1, 1914

By Reno H. Sales

Jan 1, 1914

By Robert H. Richards

Walter Renton Ingalls recently gave a very interesting talk before the student mining society of the Massachusetts Institute of Technology. In it he showed the present status of mining as he sees it. In the talk he explained that, while discoveries of great mining districts are still pssible, they are being made less and less often; that the great mining companies, although there are large numbers of mines offered for sale, are finding it less and less possible to find new mines that are up to the standard of richness that they wish for purchase. The natural conclusion is that better, cheaper, and more efficient methods of mining, concentrating, and smelting are needed if the lower-grade mines are to be worked at a profit. This is true also if the high-grade mines are to yield their greatest profit. This paper deals only with the concentrating or ore-dressing problem, and gives some thoughts which point towards greater profit. In a paper on The Development of Hindered-Settling Apparatus the writer showed that there were two main lines of work that would lead to greater saving, lower tailing assay, and, therefore, greater profit. The first is the recrushing of middling or tailing products for the saving of the contained values. This is well understood and largely carried out in existing mills. The second is the saving of fine free mineral at the first opportunity. This is a matter less well understood in the mills, and to dwell upon this the present paper is written. The writer is himself convinced and hopes to convince the reader that, for obtaining the above result, not only is better classification needed, but also more classification; that is, there should be more spigots or pockets to the classifier. His attention was recently called to a small mill which had a three-pocket cone classifier fed with from 2 to 0 mm. stuff, supplying feed to four Wilfley tables. The first spigot had about all the

Jan 1, 1914