Search Documents

Discussion of the paper of R. H: Sweetser,. presented at the Cleveland meeting, October, 1912, and printed in Bulletin No. 71, November, 1912 pp. 1327 to 1334. See also Bulletin 11 No. 72, December, 1912, pp. 1561, 1562. J. J. HOWARD, Dover, N. J. (communication to the Secretary*) :-No doubt there are as many different methods of starting a blast-furnace as there are men who assume that responsibility. Having blown-in a furnace a few years ago in a manner similar to that outlined by Mr. Sweetser, things went along so well at the start that I had time for a little reflection on what was going on inside the furnace. I saw the wood turned to charcoal practically, and it occurred to me, why should I use wood when I could put in the charcoal in the. first place, and thus save a lot of time, and also eliminate the dangerous gas from the wood, which is the cause of most of the accidents in starting up a furnace. I had a furnace out for repairs and decided to use no cord-wood in blowing in. I put in about a carload of charcoal and used no wood except some shavings and oily waste at each of the tuyeres. The furnace had 16 tuyeres and was 100 by 22 by 14.5 ft. Hot rods were put in each tuyere' and the blast started immediately at 11 a.m. Within 5 mill. the air was all driven out of the stack and the gas lighted of its own. accord at the top of the furnace. It was allowed to burn for 5 min. longer and then the bell was closed and the gas taken to the last stove and the last boiler on the gas-main. It was all clone so quietly that it was hard to realize that the gas was down. The tuyeres were as bright as if the furnace had been in blast for a long time. I have learned since that others have used the same method, but they had not passed the good advice along.

Jan 5, 1913

By R. R. Givler

Since the 1860's the good ole days, oil has been nozzle fed to burners under pressure atomizing the oil into droplets -- 1960's has produced vaporized oil that burns oil with the flame color and consistancy of gas -- If you can tell the difference by looking at the flame, gas or oil I?ll buy the lunch. First, we must ask, "Why all the excitement about Blue Flame?" This question is best answered by you after you have studied the principle of operation and see the result. I will attempt to explain both of these so that you can draw your own conclusions.

Jan 1, 1975

By Angela Binder, Oliver Langefeld

"The future of mining will be characterized not only by the application of modern technology, but also by the harmonization of economic, environmental and social issues. These areas set major future challenges which are complex and demand extensive knowledge. As an example, mining of highly complex orebodies for the supply of often critical raw materials, needs to consider technically demanding and cost-intensive extraction issues. The amount of tailings, which need to be stored, increases with the amount of ore mined. Therefore, the negative impact on environment and society increases. Hence mining becomes expensive with regard to all three aspects: economy, environment and society. In view of a sustainable mining practice this challenge should be used as an opportunity. The positive impact should be maximized for present and future generations. The objective is to create and use the mining openings in an optimum way related to sustainability. The approach of Blue Mining, which focuses on energy and ergonomics in the field of Sustainable Development, enhances the closure planning by recommending subsequent usage of such openings for energy storage. The approach fosters among others the implementation of the 7th Goal for Sustainable Development defined by the United Nations with the assurance of access to affordable, reliable, sustainable and modern energy for all. The usage of underground storage increases the stability of solar and water power usage, which are otherwise unreliable. Blue Mining embeds these issues in the main planning effort long before groundbreaking. This approach involves experience from past and current projects. This paper introduces the concept of Blue Mining with respect to post-mining utilization of a mine for energy storage. Methods and perspectives are presented with examples covering best-practices and lessons-learned."

Jan 1, 2017

By S Nowosad, A Binder, O Langefeld, M Bothe-Fiekert, F Apollo

The mining industry faces complex and urgent challenges driven by an increasing demand for raw materials, and a socially demanding globalised world. The extraction of primary raw materials is today more important than ever as one of the cornerstones towards a sustainable future since the increasing demand for the raw materials required for the energy transition. In the last three years, leading countries as USA, China, Canada, Australia, and the European Union (EU) have developed and adopted strategies to enhance domestic extraction capabilities, diversifying sources, fostering innovation in recycling, and promoting international collaboration related to critical raw materials. On 2022, the Inflation Reduction Act was signed into law in the USA, in June 2023, the Australian Critical Minerals Strategy 2023–2030 was published and in March 2024, the Council of the EU adopted the European Critical Raw Materials Act. On the other hand, raw materials extraction is facing higher environmental and safety standards and regulations, as well as scrutiny from the broader public. Regrettable environmental accidents as tailing dam failures or acid mine drainage occurrences have led to a general distrust of mining activities leaving mining companies with the dual imperative of increasing output while implementing sustainability, decarbonisation, and circularity as a core value in their production processes. This challenging environment offers the opportunity to enhance ‘blue mining’ (BM) as a sustainable holistic approach that integrates the principles needed to plan sustainable, reliable, and responsible mines for today’s and future generations by implementing the principles of circular economy (CE). This requires a fundamental shift from the traditional linear economy approach to a sustainable, circular economy strategy. At its essence, BM encapsulates four crucial aspects – energy, ergonomics, water, and circularity and integrates these four aspects into integrative mine planning, defining clear goals and objectives from the ‘blueprint’ of a mine towards a beneficial post-mining activity. Its implementation can lead to maximisation of resources beyond the life of the extractive mine and sustainable use of materials by integrating the principles of circular economy and multiuse mine, see Figure 1. These concepts complement and recognise the need to minimise environmental and social impacts while advancing economic development. Finally, this contribution explains the requirements and challenges of moving from linear to dynamic planning approaches under the BM concept. This way, BM stands as an approach that can contribute to the mining industry receiving necessary approvals and support from society leading to a long-term transformation of the industry’s image.

Sep 1, 2024

By Angela Binder, Mareike Schubert, Yichen Jiang, Sandra Nowosad, Oliver Langefeld

GermanyINTRODUCTIONThe mining industry is currently characterized by various factors such as environmental impact, resource scarcity, social responsibility and geopolitical uncertainty. The production of minerals required to meet the demand for renewable energy is expected to increase by 500 % by 2050, particularly for critical minerals such as graphite, lithium and cobalt 1. Easily accessible deposits are often depleted, meaning that deeper and more complex deposits need to be developed. Furthermore, investors’ value systems have shifted towards more sustainable practices. Alternative approaches to solving this problem are therefore currently being developed, such as the Modular Mining Systems concept for scalable and adaptable mining projects 2. Many mining companies have also taken important steps to become more sustainable, implementing measures such as proactive closure strategies, restoration programs and the development of renewable energy projects. In the European Union, laws such as the Critical Raw Materials Act and the Net Zero Industry Act support the mining industry 3,4. They see it as important for the energy transition and promote more sustainable ways of working in the industry Particularly negative environmental impacts such as land degradation, scarcity of local water resources, water pollution and greenhouse gas emissions are ingrained in society’s memory. Despite these efforts, the public image has not yet changed. To change this perception, the industry must strive to better communicate its sustainable practices and the steps it is taking towards a more responsible and sustainable future, promote transparency and build trust.Digitalization, automation and electrification are driving the digital transformation in mining. However, their implementation can lead to higher capital expenditure, limiting their adoption across the industry. Furthermore, implementing new technologies can be a daunting task for any organization. Change management comes into play when introducing such disruptive technologies. It involves preparing an organization for change, potential resistance and establishing effective communication. This helps to ensure that the implementation is successful and the benefits of the new technology are maximized. Digital transformation requires well-trained, young mining, electrical, mechatronic and software engineers with a deep understanding of information systems. Unfortunately, the industry faces the enormous challenge of attracting this younger generation, who have little interest in the extraction of raw materials. The need for action is compounded by an aging active workforce heading into retirement and the forecast of increasing demand for critical minerals.In this challenging environment, the concept of Blue Mining with its constant further developments represents a promising approach. This implies a shift from a linear to a sustainably oriented circular economy. For the mining industry, this specifically means the introduction of innovative technologies, the increased recovery of materials from waste and the consistent questioning and application of circular principles along the entire life cycle of a mine. Such a change can not only reduce the environmental impact, but also contribute to economic resilience and increased social acceptance of mining.

Feb 1, 2025

By DALE MacGREGOR, VERA TUREK

The Blue Mountain nepheline syenite deposit has been the subject of several detailed studies. It has been variously referred to as an intrusive stock, a metasomatic deposit, an intrusive sill and a metamorphic-metasomatic body. The body is divided into six mineralogical zones, the first five being based on the characterizing accessory mineral; muscovite, muscovitemagnetite, biotite-muscovite, biotite, hornblende and pink syenite. Mining currently takes place only in the biotite zone. Foliation is particularly prominent in the central (hornblende) zone and near the margins of the nepheline syenite. Majic bodies within the nepheline syenite may represent basic rocks that have been less altered by metasomatism, metamorphosed basic dykes or sloped blocks of metasediments. The most prominent structural features are the northeast-trending folds that have been modified by later north west-trending folds.

Jan 1, 1984

By McQueen LB

The Water Board has been involved in the development and ipgrading of sewerage facilities in the Blue Mountains since 1980. In 1984 the Board prepared a report that dealt with the Blue Mountains Sewage Effluent Management study. Successive 3ovemments have been concerned about development in the 3lue Mountains and the effect this development is having on the luality of the streams flowing into the Blue Mountains National ?ark (presently up for World Heritage Listing).

Jan 1, 1993

By W. R. Ingalls

SOME months ago, I had occasion to make an investigation that introduced the subject of blue powder that is produced as a byproduct in zinc dis-tillation. Although every zinc smelter is aware that more or less blue powder production is inevitable and there is a common practice as regards the treatment of it, the specific and quantitative data respecting the subject were more imperfect than would have been expected. I had reports from eight important works. Some of the data were especially determined for my investigation. Speaking generally, there is a good deal of uniformity in the figures, all of which show that the blue powder product, bears a large proportion to the ore originally charged into the retorts; that a large proportion of the retort capacity is devoted to the redistillation of blue powder; and that of the spelter product of a furnace about 30 per cent. is derived from blue powder, i.e., it is zinc that has been distilled twice. The figures from the works are given in the following table:

Jan 4, 1922

By Jeff Hopple

"Bluestone Dam in Hinton, W.Va., along the New River, is owned and operated by the U.S. Army Corps of Engineers (USACE). Completed in 1949, the dam is 165 ft (50 m) tall, 2,048 ft (624 m) wide, and encompasses a water shed that is 4,600 sq mi (11,914 sq km). The Bluestone Dam Safety Assurance (DSA) Program began in 2001, and is a multiple-phase construction project to upgrade the capacity and stability of the structure to meet the probable maximum flood event. Installing 216 high capacity rock anchors was a major feature of the work.The USACE selected Brayman Construction Corporation to perform Phase 2B of the construction modifications to the Bluestone Dam. Brayman was responsible for installing the high capacity rock anchors, which range in size from 3 to 61 strands and have a design load up to 2,145 kips (9,541 kN). Drill holes range in size from 6.5 to 15 in (16.5 to 38 cm), and required full length corrosion protection. Of the 216 anchors, 57 were installed on top of the dam to resist overturning and the remaining 159 were installed on the face of the dam at a 45-degree angle to resist sliding.To gain access to the face of the dam anchor locations, the project required dirt benches, excavations with temporary shoring, and steel platforms. To access anchors on the east and west abutment faces, the team excavated over 10,000 cu yds (7,645 cu m) of material. Support of these excavations included the design and installation of three soil nail walls with over 145 nails and 3,500 sq ft (325 sq m) of shotcrete. The project also called for a 780 ft (237 m) long steel platform to gain access to the spillway anchors. The Stratus Group designed the platform to support two 85 ton (80 tonne) crawler cranes and as many as five drill rigs that were the equivalent to a design load of 3.5 ton per sq ft (335 kN per sq m). Once the final platform design was approved, fabrication of roughly 3 million lbs (1,360 tonnes) of structural steel began. Brayman’s in-house fabrication shop, in conjunction with Dura-Bond Industries and Advantage Steel, collaborated to fabricate and install the platform in less than five months. Flexibility in the platform design allowed for sections of the platform to be lowered as much as 16 ft (4.9 m) to provide access to anchors at lower elevations along the spillway face. In addition to the main spillway platform, Stratus Group, Brayman, Dura-Bond and Advantage designed, fabricated and installed six other unique platforms to facilitate anchor construction on various areas of the dam."

Jan 1, 2014

By W. J. Maloney, H. E. Tuneblom, A. J. Smith

The development of a large regional water supply in Southern West Virginia faced several hurdles. This paper deals with the design and construction of the intake shaft where a combination of cutting edge mechanical excavation technologies were utilized to produce a world class project.

Jan 1, 1999

By Donald C. Trueblood

Since the Surface Mining Control and Reclamation Act (SMCRA) was passed in 1977, coal mine reclamation has been restricted from utilizing bluff-1ike features in permanent reclamation. This restriction is based on those provisions of SMCRA which require the elimination of all highwalls. In 1987, the Wyoming Mi ni ng Association began an effort to acquire the ability for coal mines to utilize bluffs in permanent reclamation for the purpose of enhancing the post-mining land use. The regulatory reform approach being uti1ized includes formation of a work group with members from industry, government, agriculture, and environmental organizations to prepare a proposal. Advantages of this approach are discussed.

Jan 1, 1989

By A. Fischersworring-Bunk

The new inline six spark-ignition engine is the realization of BMW's concept of efficient dynamics at high technological level to achieve the attributes of low weight and high efficiency, The paper presents different aspects of the development and manufacturing of BMW's inline six-cylinder engine magnesium-aluminium composite crankcase, Reference will be made on the AJ magnesium alloy optimization approach to balance between mechanical properties and the high pressure die cast ability requirements, Next to this aspect some mechanical design issues will be covered, with CAE methods playing an instrumental role in the early project stage for the assessment of the compound concept, Due to the compound design chosen, the interface posed challenges to both design and productions, A set of novel techniques has been used to cope with these tasks.

Jan 1, 2006

By Debbie Nakamura, Daniel Tempelis, John E. Shamma

The Metropolitan Water District of Southern California established a Board of Consultants to assist them in administering the design and construction of the Inland Feeder Program tunnels. The Board acts as an expert review body for the owner, looking at key issues that can potentially impact the success of the program. The use of the Board evolved over the life of the project, and its composition was modified to better address the needs of the owner, and the Program requirements. The experience, function, and value of such a board is analyzed and discussed in this paper.

Jan 1, 2003

Meeting, Mar. 28, 1913.-The following Committees were appointed : Library ; Membership; Precious and Base Metals ; Papers and Publications ; Economic Geology ; Iron and Steel ; Increase of Membership; Stocking Pamphlets and Publications; and the following representatives: Joint Conference Committee of the four National Engineering Societies; General Committee in Charge of the International Engineering Congress, 1915. Delegates were appointed to attend the International Geological Congress and the Fifth Conservation Congress. These appointments are listed on pp. xxxvii. to xxxix.

Jan 4, 1913

Meeting of May 22, 1914.-President Thayer. announced the appointment of the following Committee on Arrangements for the San Francisco meeting of 1915: Charles W. Merrill, Chairman; F. W. Bradley, Abbot A. Hanks, S. B. Christy, and H. C. Hoover. President Thayer announced the appointment of the following Committee on Organization for the Utah-Nevada Local Section: R. C. Gemmell, Chairman; C. D. Blood, Lafayette Hanchett, Ernest Gayford; Duncan MacVichie, and George W. Riter. The President of the Institute offered $100, to be known as the "President's Prize," to be used as prizes for the best papers submitted by members of the Affiliated Student Societies, to be divided as follows: First Prize, $50; Second Prize, $30; Third Prize, $20. A committee, consisting of J. F. Kemp, Chairman; W. L. Saunders, and T. T. Read, was appointed to report on the conditions to govern the award. The President announced the appointment of the Committee on Mining and Milling Methods, the personnel of which is shown on a subsequent page of this Bulletin. The following were appointed on the Advisory Committee to the U. S. Bureau of Standards, to represent the manufacture of the various non-ferrous metals as indicated: Copper, F. L. Antisell; Nickel, David H. Browne; Lead, H. O. Hofman; Aluminum, J. W. Richards; Zinc, G. C. Stone. It was voted to hold a meeting of the Institute under the auspices of, the Iron and Steel Committee, the Committee on Petroleum and Gas, and the Committee on Coal and Coke, in Pittsburg, Pa., Oct. 8, 9, and. 10, 1914.

Jan 7, 1914

Meeting of Feb. 16, 1915.-The Committee on Membership was appointed with the following personnel: John H. Janeway, Chairman; Karl Filers, Lewis W. Francis, Louis D. Huntoon, and Thomas H. Leggett. President Saunders announced the appointment of the Committee on Increase of Membership, as shown on p. xxviii of this Bulletin. The reproduction by the anastatic process of 100 copies of Volume IX of the Institute Transactions was authorized. The sum of $50 and the exchange of the Bulletin. was awarded to the commission publishing the Annual Table of Constants. The sum of $49.07 was contributed to the expense of the John Fritz Medal Board of Award for the year 1914, and the Institute agreed in the future to share the annual expense for the John Fritz Medal Board of Award not to exceed one-quarter of $500 in the year. Upon the recommendation of the Committee on Membership, 36 Members, 1 Associate, and 13 Juniors were elected. The resignations of 26 members were accepted. L. D. Ricketts was elected a Vice-President of the Institute to serve the unexpired term of W. L. Saunders. George D. Barron was elected a Director to serve the unexpired term of L. D. Ricketts.

Jan 4, 1915

Meeting of June 4, 1915.-The President announced the appointment of the following Committee on National Reserve Corps of Engineers: Dr. Henry S. Drinker, Chairman; Arthur S. Dwight, and Warren A. Wilbur; also, the appointment of Arthur F. L. Bell as Chairman of the Committee on Petroleum and Gas, and of James F. hemp as Chairman of the Committee on Mining Geology. All of these appointments were approved. It was voted that the following minute be, placed on record and a copy sent, by order of the Board of Directors, to the family of John Birkinbine: "The Board of Directors of the American Institute of Mining Engineers hereby records its sense of sorrow and loss in the death of John Birkinbine, a former President, and for many years an active member of the Institute, and contributor to its Transactions. "Mr. Birkinbine's eminence as an engineer, author and editor, intimately connected with the industrial progress of the United States, brought him into contact With the leaders of science and the captains of industry, among whom his genial and estimable personal character won for him many friends; and his departure in the prime of Strength and usefulness is mourned by a wide circle."

Jan 7, 1915

Meeting of Sept. 25, 1914.-The Committees to have charge of the arrangements for the Annual Meeting in New York, Feb. 15 to 18, 1914, were appointed. It was voted that the Secretary of the Institute take up with the Chairmen of the Local Sections the question of arranging for the transportation to the meetings of the Institute of the members of the respective sections. The Board of Directors unanimously voted to extend to each and all of the members of the Local Committees of the Salt Lake Meeting its hearty thanks for their efforts which resulted in the very successful meeting. The President was authorized to sign the letter to the President of the United States in regard to the appointment of some representative of the mineral industry upon the Federal Trade Commission. An appropriation of $250 was granted to the Southern California Local Section. The By-Laws of the Utah Local Section were approved. Upon recommendation of the Committee on Membership, 133 members, 7 associates and 13 juniors were elected to membership. BRADLEY STOUGHTON, Secretary.

Jan 11, 1914

Meeting of Dec. 19, 1913.-The President reported the appointment of the Committee on Junior Members and Affiliated Student Societies, and the Committee on Coal and Coke, which .appointments were approved. The President was authorized to appoint the members of a Committee on Safety and Sanitation. The President appointed the Finance Committee of the Institute as a Committee to audit the accounts of the Treasurer (By-Law V). On the recommendation of the Executive Committee, Charles F. Rand was appointed a representative of this Institute on the Board of Trustees of the United Engineering Society for a term of three years (By-Law XIV of the Institute, By-Law XI of the U.E.S.). The Executive Committee reported that it had passed the following resolutions: That the next summer meeting of the Institute be held at Salt. Lake City during Aug. 10 to 14, 1914, inclusive; That an exchange of .the Bulletin and Transactions be made with the Canadian Bureau of Mines; That a sum of $50 be contributed for the year 1914 to the Commission publishing the Annual Tables of Physical and Chemical Constants; That the Secretary be given power to reduce at his discretion the number of exchanges between the Bulletin and other publications which are not retained as a permanent part of the Library; That the contract for binding Volume XLV of the Transactions be awarded to the Butler, Ward Co., in accordance with their bid of Nov. 21, 1913;

Jan 1, 1914

Meeting of Oct. 23, 1914.-It was voted to take no action concerning the proposed amendments to Article VIII, Sections 2 and 3, but that they be sent to the membership, as provided by the Constitution, together with a statement of the arguments for and against the proposed changes. It was voted that the following proposed amendment, which had been unanimously approved at the annual meeting of the Institute on Feb. 18, 1914, be sent to the membership as provided by the Constitution, together with the approval of the Board of Directors of this change: Article III, Section 1, paragraph 3, sentences 2 and 3: substitute the following: "Any Member, Junior Member or Associate in arrears for two years shall be dropped from the rolls unless the time for payment is extended by the Directors. A Member so dropped may be reinstated by the Directors on paying the arrears of clues and other indebtedness with which he was charged on the books of the Institute it the time he was dropped. A Member or Associate thus reinstated shall receive the Transactions for the back year for which he pays." It was unanimously voted to extend the sincere thanks of the institute to Samuel A. Taylor, Chairman, and to each member of the several Committees of the Pittsburgh meeting, for the enjoyable and successful meeting which they brought about.

Jan 12, 1914