Search Documents

By O. Saeki

Dolomite-fluxed pellets have been produced at Kakogawa Works, Kobe Steel, Ltd., since August, 1975. The pellets contain 5.5 % dolomite and have a basicity (CaO/Si02) of 1.3. By charging 30-50 % of dolomite-fluxed pellets into the two large blast furnaces at Kakogawa, a low fuel rate of 450 kg per ton of pellets has been achieved with better furnace permeability and gas utilization. Laboratory studies show that dolomite-fluxed pellets have excellent high temperature properties, and that their softening and melting-down temperatures are about 50°C higher than those of lime-fluxed pellets, and that reducibility at 1250°C is increased from 25 to 70 %.

Jan 1, 1977

In today’s competitive steelmaking environment, the optimization and continuous supervision of the blast furnace process is of major importance. Modern probes and process measurement systems can assess the specific operation of the blast furnace. They provide a better and detailed process understanding and control. The benefits are even more important when they are combined with process models and expert systems. Everyday operation, productivity and even the lifetime of a blast furnace can be significantly improved by collecting, interpreting and acting upon such process data correctly. Only a comprehensive knowledge of the various process phenomena together with measurement of process variables inside the blast furnace enables the operators to optimize coke and fuel rates, to run the blast furnace smooth, reliable, and safe, and to make best use of the available raw materials. While the improvement of the blast furnace process with respect to productivity remains the main task, also, the timely identification of abnormalities and the assessment of process variations is an objective. This paper describes the blast furnace measurement systems that are available for everyday automatic use and provides an understanding for the possibilities of modern probes. The different applications are daily blast furnace supervision, charging process optimization, and observation of the internal state. Finally, the paper gives recommendations on probe configurations for different blast furnaces sizes, considering both a technical and an economical point of view.

Aug 2, 2018

Previous studies on the blast furnace raceway zone have been undertaken at three levels of scale, namely: laboratory models at low temperature, hot models which simulate coke combustion in the zone, and tests performed on operating and dismantled blast furnaces. This paper reviews the results of this published work on raceways in order to illustrate the factors which affect the raceway shape, size and combustion characteristics. As a result of the work it has been established that raceways are influenced by blast parameters such as velocity, temperature and chemistry, as well

Jan 1, 1981

During the last 20 years, manufacturers of Australian iron have given increasing attention to development of external markets for processed blast furnace slag. Slag has been in widespread use overseas and data on the performance of Australian slag in concrete lave shown it is suitable for that use. Chemical and physical properties of typical Australian slag products including air cooled, granulated and pelletised slag are discussed and compared with local natural aggregates. Special attention is given to pumping achieve- ments with slag concretes and the observed durability of concrete after many years service. More'recent applications for granulated slag as a sand replacement are discussed. It is concluded that'whilst more wide- spread use of slag is possible, the cost of marketing and transporting slag are likely to restrict opportunities unless for local usage.

Jan 1, 1979

By Z. Halifa, P. G. Geyer

Tapping a blast furnace is necessary not only to deliver the product, but is also essential for the safety of the furnace and workers in the cast-house. This paper will highlight the practices at ArcelorMittal’s blast furnaces in the Vanderbijlpark Works, with specific focus on tap-hole design and monitoring as well as casting practice. Extension of the tap-hole life and hearth campaign will be illustrated with reference to the methods of maintenance of the tap-holes, troughs, runners, and cast-house equipment. The importance of proper cooling, good thermocouple installation, and temperature monitoring will be explained.

Jan 1, 2014

By M. Adnan Goksel

A blast furnace test of approximately 5,000 tons of PelleTech Corporation (PTC) cold bond pellets was successfully run at Kaiser Steel Corporation (Kaiser) Steel Manufacturing Division at Fontana, California. The pellets were produced from mill scale, BOF dust and blast furnace flue dust. A 15 day base period, during which time the metallic burden was 2/3 heat indurated pellets and 1/3 sinter, preceeded the test. During the test period the metallic bur- den was 10% cold bond pellets, 56.7% heat indurated pellets and 33.3% sinter. A 15 day post test base period followed during which the PTC pellets were replaced by conventional pellets. The pellets were produced in the 3.C Semi-works Facility located on Kaiser property. The facility incorporates the Michigan Technological University Hydro-Thermal Agglomerating Process.

Jan 1, 1979

By Peter K. Strangway

During 1973, a 20,000 net ton (18 100 metric ton) formcoke test was carried out at Inland's 26.5-foot (8.08-meter) hearth diameter on NO. 5 Blast Furnace. The formcoke briquettes were produced from Elko1 coal by FMC at their pilot plant in Kemmerer, Wyoming. The briquettes were shipped to Inland in open railroad cars and most of them were placed in an outside storage field until a sufficient amount was available for the actual blast furnace test. The test consisted of three phases: an initial four-week base period; the actual 33-day formcoke test period; and a final three-week post-test base period. During the formcoke test period, the regular coke skip loads were gradually replaced with skips of formcoke until, after a three-week period, the replacement ratio reached 80%. The furnace operated smoothly and quality hot metal was produced. The burden remained permeable and it was possible to maintain wind rates 9 of over 100,000 scfm (47 Nm3/s) without significant blast pressure increases. Dusting from the formcoke was not a problem either in the stockhouse or in the top gas. The formcoke briquettes maintained their original shape and density as they descended through the furnace. When the 80 percent replacement level had been reached, the inwall temperatures became higher than normal (about 2000 ºF (1090 ºC)) and followed an unusual steady pattern. In addition, the top gas temperature became higher than normal, and the hot metal analyses and temperatures began to fluctuate unacceptably. In general, it is felt that the high inwall temperatures were a result of channeling of the hot furnace gases along the stack walls. This channeling appears to have been promoted by a change in distribution of the burden in the top of the furnace which, undoubtedly, was caused by the increased increments of formcoke. Since it was felt to be unsafe to operate the furnace for an extended period of time with the inwall temperatures at the high level, a decision was made to remove the formcoke from the furnace. When this was done, the inwall temperatures returned to normal. Once the inwall temperatures had returned to normal, the remaining 3,800 net tons (3450 metric tons) of formcoke were used in the furnace at a nominal 40% replacement level for five continuous days. The furnace operated smoothly during this period, and the results were representative of satisfactory furnace operation with partial replacement of regular coke with formcoke. The test was successful in proving that formcoke can replace up to about 50% of the regular coke in a large furnace operating at high wind rates. However, additional work will be required to develop acceptable charging practices for using higher levels of formcoke replacement.

Jan 1, 1977

By J. S. Young

During 1975, the Reclasource Corporation constructed and commissioned a plant for the recovery of mill scale, coke breeze, blast furnace dust, blast furnace sludge and basic oxygen furnace dust at the site of Crucible Alloy Division, Midland, Pennsylvania. The Reclaform Process was employed as the criteria for plant design. This Process takes the solid in-plant fines as listed above, commonly found in integrated steel mills, sizes and forms them through the use of a carbonaceous binder briquetting system and cures the binder through a final heat-treating step. 15,000 tons of Reclaform briquets have been tested in the Crucible blast furnace in several campaigns structured to assess material handling properties, burden feasibility and finally culminating in an iron and carbon assessment campaign. Data are presented from the records of the blast furnace operation and conclusions are drawn that both iron and carbon utilization have been demonstrated.

Jan 1, 1977

In blasting large tonnages of ore or material, the economy of the operation 'depends mainly on the mine manager's judgment in placing the holes to the best possible advantage and in determining the most effective size of hole to suit the conditions and requirements.The placing of holes is often looked upon as a problem involving so many uncertain factors that the application of simple mathematics is impossible. The uncertain factors arise when dealing with strata of different character, in hardness toughness and resistance to shearing.A study of the practice at many mines where all types of strata from hard ore to relatively soft overburden, and even coal, is being mined, suggests that the problem is not as complex as generally believed. There is, without doubt, some uniformity in the amount of burden given to holes of equivalent dimensions, regardless of the material being mined. The reason is simple. With too great a burden hard rock will not break out and soft rock will "bull". The nature of the strata is taken care of by the strength, quantity and distribution of the explosive charge and, to some extent, the spacing of the holes.It is because burdens are uniform in all classes of strata met with in mining, that a formula can be used to design blast hole layouts.The formula introduced in this paper is empirical as it is based on prevailing practice. It has been tested and proved remarkably accurate against every example available to the writer. Many thousands of blast holes, at many different mines, are represented by the examples given in the attached tables; to give further examples would only mean, unnecessary repetition. At the Mount Morgan Mine...

Jan 1, 1952

By Creelman C. A

With the technique and data obtained in using the blast hole diamond drill for "Removal of Horizontal Level Pillar by means of Blast Hole diamond drilling at New Occidental Gold Mines N.L.," as described in Proceedings No. 133 of 1944, and a series of experiments using the blast hole diamond drill for stoping at New Occidental and New Cobar Mines over the past two years, a benching method of stoping has been developed using 2 inch coring diamond drill bits, resulting in efficient and economical ore extraction in these large ore bodies.During the experimental stages the standard H-inch blast hole was used, but the deflection of the holes, when using this solid bit, either decreased or increased the burden of the hole when it became necessary to drill holes deeper than 45 feet.It was found that after blasting vertical holes deeper than 45 feet, the ore did not break satisfactorily over the full length of the hole; on one occasion as much as 30 feet of bench was left at the bottom of the face, which had to be subsequently re-bored andblasted.As this defect was also noticeable to some extent even when the holes did not deflect, it was then obvious that the explosive had become less sensitive in the lower section of the hole. This was probably brought about by pressure being built up ahead of the detonation wave in H-inch hole, resulting in desensitization of the explosive.Another series of experiments were carried out, using 2-inch solid bits, which enabled a much greater burden on the holes, and the use of primacord for the full length of the hole.This gave satisfactory results regarding breaking and fragmentation, but was uneconomic owing to the excessive consumption of diamonds, and the slow rate of drilling.Further experiments were then carried out using 2-inch coring bits, (Fig. 1) which allowed holes of 90-feet to be bored with little deflection, and proved to be entirely satisfactory as to cost and speed of drilling.

Jan 1, 1945

By T. E. Scartaccini

A drill recorder is a permanent data collecting instrument. In open pit blast hole drilling the application of a drill recorder is that of data collection, drilling control, and drilling education. The various drilling parameters (weight, RPM, penetration, torque, and air) have a drilling correlation which can be demonstrated and documented by a recorder graph. When the correlation is physically put to use during the process of drilling, then the recorder has become a drilling tool and is no longer just a data collecting instrument, per se. By being able to maintain accurate records and drilling control, comprehensive studies of changes both operational and technological can be made. These are based on in-progress facts and not after-the-fact logs. To determine total drilling efficiency, drilling conditions must be documented and controlled. Field operations at American Smelting and Refining Company's Mission Mine have proved that by increasing drilling control, demonstration of parameter relationships, and drill monitoring, more economic efficiency can be obtained. In comparing results obtained with recorder control and conventional control a decrease of 14 percent to 36 percent of drill footage costs were obtained. The percentage of variance is dependent upon whether drilling is milled-tooth or carbide-insert bit drilling.

Jan 1, 1970

By Dwayne D. Tannant

The Fox Pit at EKATI Diamond Mine reached a depth of approximately 150 m as of September 2005. The pit is designed with 11 m wide benches excavated using a double benching technique leaving 30 m high bench faces. A series of blasting tests were conducted to improve catch bench reliability and increase the percentage of benches that meet an 11 m catch width. The design changes focussed on reducing damage to the bench crest because maintaining the bench crests is the most important factor in achieving good bench reliability. The most significant improvement was obtained by raising the bottoms of the lower trim blastholes by 0.5 m. This change decreases the depth of broken rock below the final bench elevation, and consequently reduces damage to rock that forms the bench crest below. Another improvement was the use of smaller diameter (165 mm vs. 270 mm) blastholes in the A and B rows for the upper trim blast. This change reduces the charge per delay during detonation, reduces the powder factor slightly, and reduces the energy affecting the final pit wall and crest. As mining and the blast testing progressed, the portion of the bench with crest achievements (>11 m) increased from 57% to 75%.

May 1, 2006

By G Billing a, D Gribble, E Hall, D Varga

The theoretical benefits of electronic detonators have been reasonably well documented. To support this, a practical comparison was made between the performance of the standard shock tube system, NONEL, and a high precision electronic system, HotShotÖ, at the Sunrise Dam Gold Mine. The expected benefits from electronic detonators to Sunrise Dam were identified prior to the trial. Based on these, a number of objectives were set to demonstrate the value of the HotShot system. These are an improvement in fragmentation leading to an increase in productivity, less oversize rehandling, increased throughput and more uniformity in muck pile movement. To maintain the integrity of the trial, the nominal timing of the shots was kept exactly the same, thereby restricting any performance improvements to the precision of the electronics. Accordingly, adjacent shots were chosen with consistent geology. Video footage was taken of the blasts and vibration monitoring was carried out by fixed geophones throughout the mine. Spot heights of the muck pile swell were taken immediately after the blast and heave profile graphs were generated for comparison. Video footage was taken for a period of three hours for both shots to analyse cycle times of the excavator and trucks. PITRAM data was also collected for analysis. As far as practicable, the ore was taken to the same finger on the run-of-mine (ROM) pad to assist in single sourcing for the crusher and to allow oversize to be separated out. From specific metrics taken during the trials, it was shown that the expected improvements due to the high precision timing of electronics were realised in all areas.

Jan 1, 2007

By Anders Nordqvist

LKAB operates an underground iron ore mine in Malmberget in the northern part of Sweden. Twelve different orebodies are mined today using both longitudinal and transversal sublevel caving as mining method. The town of Malmberget is located close to the mining area. The need for urban transformation, moving people and houses, is evident for many reasons. The mining methods used have inherent subsidence issues and there are also vibrations from blasting and mine induced seismic events.

Jan 1, 2018

By A. K. Debnath

Coal is the mainstay of Indian energy supplies. The many-fold increase in demand for coal puts a huge pressure on augmenting production, primarily from opencast mines. The increase in production necessitates heavy blasting in overburden and coal benches of opencast mines, which poses numerous challenges in carrying out blasting operations techno-economically. Presently, the consumption of industrial explosives and accessories in Coal India Limited (CIL) has touched a whopping figure of $350 million USD per annum and CIL will be spending approximately $1 billion USD between 2012?2013 to 2014?2015 for procuring explosives and accessories. This paper discusses some of key challenges faced in various mines of CIL during blasting, where blast instrumentation at the mine level will prove to a harbinger for practicing blasting engineers. Presently, the problem of scattering in surface detonators and down-the-hole detonators affects the blast performance significantly by increased blast induced ground vibration and reduced fragmentation. The paper discusses a case study carried out at Umrer opencast project of CIL to investigate the effect of scattering by using blast simulation techniques (i.e., JKSimblast) and observing the actual blast results with the help of a high-speed camera and multi-channel high frequency data acquisition systems. The fragmentation assessment was carried out by adopting Digital Image Analysis techniques and using the granularity software viz. Wipfrag. The blast instrumentation in the case study mine resulted in improvement in fragmentation of 12.76% and a direct savings in explosives cost of 28%. Geophysical techniques such as the seismic survey method have been used at Umrer Project, CIL to characterize the rock mass using the Multi Channel Analysis of Surface Waves system for selecting the explosives technoeconomically. The minimum deck thickness for mines of CIL using drill cuttings as decking materials should be 10 D, where D is the drill diameter. The estimation of blast performance on the basis of prescribed Powder Factor (i.e., kg of explosives per m3 of rock) is technically unscientific as the criterion of a good blast depends on many factors (i.e., good heave, loose muck, muck profile angle, ease of digging, uniform fragmentation). The present paper proposes a new methodology for techno-economic evaluation of blast performance. The new methodology involves four significant factors viz. specific energy consumed by the loading equipment, charge factor, productive yield and diggability index for assessing blast performance. The use of user-friendly, accurate, reliable, rugged and handy instruments in blasting will significantly improve mine productivity, equipment efficiency and economics. The improvement in blast performance, even by 1%, will provide a significant savings of $3.5 million USD per annum to CIL. It may be concluded with high degree of confidence that blast instrumentation at the mine level will influence the mine productivity and economics.

Aug 1, 2013

By Siddall B

A brief review of the capabilities and practical limitations of blast simulation packages has been carried out. It is concluded that the simulators accurately reflect size distributions in the mid-ranges of 0.1 to 1.0 in, but are less reliable

Jan 1, 1998

By Grigor Mishev, Georgi Petrov, Benjamin Cebrian

Before designing a single blast or all the blasts on a pit level, it is critical to assess the main goal on each. To do this, a series of constraints must be taken into account: wall protection, vibration control, flyrock hazards, fragmentation required, desired displacement as well as economy, equipment efficiency. The tool to do this is the Blast Master Plan. Many mines fail to integrate on its elaboration key stakeholders such as planning, operations, geology/geotechnical and milling departments. Designs not only have to provide consistent behavior of the blasts, but have to make sense all in one with the geological and geotechnical conditions as a starting point. Once blasts are designed under an organized set of priorities, and complemented with quality controls, optimization is possible on a large scale.

Jan 1, 2016

By Shonn K. McNeill, Joshua Micah Hoffman

Security engineering is similar to other forms of engineering – the design is guided by the loads, materials, and desired function. For facility design, the load is the threat. Facilities that are designed with considerations for explosive hazards are designed with a shot, or series of shots, of a given size and distance from key locations. These facilities range from office buildings and industrial sites in developed nations to military and police stations in contingency areas. The challenge is the design shots are not often communicated to facility owners and managers. If the hazards change, whether it’s due to an increased capacity to cause damage by a threat or a decrease in capacity by a structure, not knowing the design shot means not knowing if security design needs to change. Blast modeling is an engineering tool that can be used to reverse engineer what a facility is suitable for, as well as be a tool for modifying security design for new conditions. This paper will examine military and civilian examples, including a case study of a military facility that did not know their as-built conditions and had to be rapidly closed; due to the determination their security engineering shortcomings could not be mitigated.

Jan 1, 2019

By Gordon K. Jorgeonson

Much of the modelling of blasting operations has been devoted to simulating blasts in open pit mines and quarries . This has been the most obvious application and has been reported in many papers and discussions in the past.

Jan 1, 1990

By Stephen H. Chung

The blasting performances identified above are considered to be the most practical ones for judging the effectiveness of a design combining explosives / rock / drill pattern. In a total blast design process, productivity relates closely to both fragmentation and heave / displacement of muck. In cast blasting, the more overburden displaced by explosives, the less blasted material there is left to be removed with mechanical equipment such as draglines or trucks. For wall protection and dilution control, estimates of the maximum extent of cracks / damage generated in situ due to blasting will help determine the location for drilling and loading perimeter blastholes.

Jan 1, 1994