Search Documents

By R. Mensah-Biney

The aqueous biphase separation process (ABS) has been used to separate ultrafine industrial minerals. The partition behavior of TiO2, Al2O3, Fe2O3 and kaolin was not pH dependent. The partition behavior of SiO2 was, however, pH dependent. The partition coefficient of kaolin in PEG 3400/ Na2CO3 biphase system was = 150 and that of the silica in the same system was = 0.02, resulting in a separation factor of = 8500 between kaolin and silica. The aqueous biphase separation system was used to separate free silica from kaolin in a raw clay sample from Mexico. The partition behavior of mica, feldspar and clay from North Carolina was also evaluated.

Jan 1, 1999

By M. M. Bwalya, F. K. Mulenga

"SynopsisThe application of the attainable region (AR) technique to the analysis of ball milling is currently limited to batch data. This paper introduces the use of the technique to continuous milling.To this end, an industrial open milling circuit processing a platinum ore was surveyed. Samples were collected and later characterized by means of laboratory batch testing. On site, several milling parameters were varied systematically so as to collect data for modelling purposes. These paramters included ball filling, slurry concentration, and feed flow rate. After data analysis, a simulation model of the open milling circuit was developed under MODSIM®, a modular simulator for mineral processing operations. The mill was then simulated and the data generated was analysed within the AR framework.Initial findings reveal an opportunity to gain valuable insight by studying milling using the AR technique. From an exploratory perspective and inasmuch as this study is concerned, feed flow rate, ball size, and ball filling were identified as being pivotal for the optimization of open ballmilling circuits. Mill speed, on the other hand, had only a limited effect on the production of particles in the size range -75 +10 µm.IntroductionGlasser and Hildebrandt (1997) propounded the attainable region (AR) as a technique for the analysis of chemical engineering reactor systems. Results have since been produced and tested on both the laboratory and pilot scales. The method results in a graphical description of chemical reactions by considering the fundamental processes taking place in the system, rather than the equipment. From the plotted graphs, the process and the reactors can be synthesized optimally into a flow sheet.The use of the AR method still has a long way to go as far as mineral processing is concerned. For instance, several articles have reported the application of the AR technique to ball milling: Khumalo et al. (2006, 2007, 2008); Khumalo (2007); Metzger et al. (2009, 2012); Metzger (2011); Katubilwa et al. (2011); Hlabangana et al. (2012). Their main shortcoming has been the exclusive use of laboratory batch grinding data.To address this deficiency, Mulenga and Chimwani (2013) proposed a way by which the technique could be extended to continuous milling. In effect, the batch milling characteristics of a platinum-bearing ore (Chimwani et al., 2013) were used and scaled up to an open milling circuit. Then, with simplifying assumptions, an attempt was made to optimize the residence time of particles inside the mill. Later, Chimwani et al. (2014a) presented some optimization examples involving various milling parameters. The sequence of published articles then paved the way for the study of industrial milling systems with the AR methodology."

Jan 1, 2015

By W. S. Tremaine

When the Hedley Mascot mill was built in 1935, it was designed as a straight flotation plant. The ore to be treated at that time was a gold ore in which the gold was intimately associated with arsenopyrite and pyrrhotite in highly silicified and garnetized limestone gangue. This material was ground to 85 per cent minus 325 mesh in two-stage grinding and floated in standard flotation cells to produce about a 5-ounce concentrate, which was shipped to Tacoma smelter for refining. This arrangement gave us a recovery of about 89 per cent. Test work indicated that the best way to improve this recovery would be to build a cyanide plant to treat our flotation middling. Arrangements for the construction of this plant were finally approved and work on it was started in the spring of 1940. This plant was of the conventional type in which the flotation middlings were thickened, filtered, and then put through the usual cyanide process. Its capacity was 50 tons of middlings per day. This arrangement worked quite satisfactorily and gave us an increase in overall recovery of 4 per cent. Unfortunately, about the time the plant was completed, we developed, and started to ship to the mill, ore that differed entirely from that met with up to that time. Instead of being hard, it was very soft, the orebody from which- it came being much faulted and brecciated. In many sections, the sulphides were oxidized and the breccia was filled in with a very soft, hydrous iron silicate known as chloropal. When this new ore was mixed with the old ore and sent to the mill, the whole operation was disrupted. The chloropal slimed so badly that the classification, flotation circuits, and cyanide plant would not handle it. The difficulty in the cyanide plant was at the head end, where the 10 ft. by 20 ft. thickener and the 8 ft. by 8ft. drum filter would not handle the middlings containing a large percentage of primary slime and chloropal. This material would not thicken to more than 30 per cent solids in the thickener and, when pumped to the filter, would forma very thin, slimy cake. Overall recovery dropped to between 83 and 84 percent and it was quite apparent that some extensive changes would have to be made in our flow-sheet before this ore could be treated successfully.

Jan 1, 1947

By Türker Hüdaverdi, Özge Akyildiz

"In this research, image analysis technique, Kuz-Ram and KCO Models were used to examineefficiency of the quarry blasts. Investigations were performed in Cendere region, Istanbul. As a firststep, image analysis software was used to determine particle size distribution of muckpiles.Additionally, the results of KuzRam and KCO fragmentation models were compared to the results ofthe image analysis technique. The efficiency of KuzRam and KCO models was investigated and theimportant points to be considered were explained. Additionally, the effect of the rock factor valueson the size distribution curves was investigated. The blasthole diameter is 89 mm. (3.5 in) in thestudied quarry. Each measured blast has a different burden, spacing and stemming length. Blastholes was drilled in a staggered pattern. It is concluded that, KuzRam and KCO models can be successfully used to determine fragment size distribution in Cendere Region Quarries, Istanbul. Site engineers can predict blast fragmentation using the theoretical fragmentation models and they may change blast design parameters before blasting operation if necessary. It is possible to calibrate the Kuz-Ram and KCO fragmentation models using the measurements obtained by image analysis technique."

Jan 1, 2016

By S. A. Abetel Sabour

In this work, the block theory was applied to determine the safe limit of the angle of face slope at Limestone quarry of Assiut cement company in order to decrease the occurrence of dangerous potential key blocks. Four joint sets were observed and measured at the face. Computer program based on the vector analysis technique was developed to determine the removable block codes. Stereographic projection was also used in this work to determine the removable block codes and to calculate the maximum limit for the angle of dip of the free face, which was found to be 77°.

Jan 1, 1998

By Williams D. J

The boundary element method is one of a number of tools that have found wide application in geomechanics for mine design and stress analysis. Two examples are presented in this paper, illustrating the use of the boundary element method to find potential problem regions in large-scale excavations. These examples are from a Papua New Guinea open cut mine and an Australian sub-level caving operation. Because of the scale of the mines and the complexity of the excavations, the boundary element method is the only practical numerical modelling technique to account for the major influences. Although the boundary element method uses only linear elastic models of the rock mass, the paper illustrates techniques for dealing with non-homogenous and anisotropic rock masses, as well as clasto-plastic effects associated with an excavation.

Jan 1, 1995

By Takeo Asanuma, Sachihiko Tokunaga, Hirofumi Taguchi, Yasuhiro Ootsuka, Yosuke Tanaka

The Cement Deep Mixing Method (CDM Method) is a ground improving method that has been used for mainly offshore sites to strengthen the soft ground below the sea bottom by injecting and adequately mixing cement slurry with soft soil into the ground to form a ground-improving column. In recent years, the CDM Method has increasingly been adopted for ground- improving work as part of liquefaction countermeasures and earthquake-resistant reinforcement in the shallow waters of river mouths and inland waters. In consequence of that, a pontoon-mounted CDM Method (CDM- FLOAT Method) has been developed for shallow waters, which is equipped with a land-type mixing machine combined with system management equipment and a tide level-based control function. This CDM-FLOAT Method can be deployed at work sites where the conventional offshore-use CDM barge cannot be employed. This report describes the CDM-FLOAT Method and the scope of applications together with construction work procedures, and a representative case of use of the CDM-FLOAT Method is introduced as an example of earthquake-resistant reinforcement of the existing embankment of a canal.

Jan 1, 2015

Since it was first introduced, the Coal Mine Roof Rating (CMRR) has been widely accepted as a tool for geologic characterization and mine planning. This paper discusses the application of the CMRR to another practical ground control problem. Extended cuts (cuts greater than 6 m (20 ft) in length) are commonly used with remote control continuous miners. Extended cuts can greatly increase productivity, but they have been associated with a number of fatal roof fall accidents. When extended cuts are attempted in weak roof, the roof may collapse before it can be bolted, causing hazardous conditions. Until now, it has not been possible to predict where conditions may not be suitable for extended cuts. In this study, data on the CMRR and extended cut experience were collected at 36 mines in 7 states. It was found that when the CMRR was greater than 55, deep cuts were routine in nearly every case. When the CMRR was less than 37, extended cuts were almost never taken. Between 38 and 55, extended cuts were feasible sometimes but not others. The data also shows that extended cuts are less likely to be stable if either the entry span or the depth of cover increases.

Jan 1, 1998

By John Rusnak

The Coal Mine Roof Rating (CMRR) is a practical rock mass classification system for use in design of mine openings. Data can be obtained for this purpose from exploration drill cores if simple geotechnical logging and rock mechanics testing is conducted. The CMRR is an excellent method to quantify rock characteristics for engineering purposes. It bridges the gap between geologic description and engineering design. The CMRR was utilized in the design of a 10,000 fl. long coal belt conveyor tunnel connecting an Eastern Associated Coal Corp. mine and preparation plant in Boone County, West Virginia. Data gathering and analysis techniques are discussed involving the calculation of the CMRR and its application in the design of the tunnel, which was driven through a thin coal bed zone. The preliminary findings have correlated well with actual roof and mining conditions encountered during driving the tunnel and it is concluded the CMRR is an effective method to utilize geologic data from exploration core holes for engineering analysis and design.

Jan 1, 1998

This paper describes the experiences with the application of the Coal Mining Roof Rating (CMRR) System to South African strata conditions. Roof classification studies using the CMRR system were undertaken as part of a SIMRAC investigation into falls of ground in South Mean collieries. Colliery roof rating exercises were undertaking in a range of geotechnical conditions from shallow level coal seams under flat topography to workings with cover depths of greater than 300m A comparison is made between the CMRR and other Rock Mass Rating systems used to classify different roof geotechnical conditions. The need for geological discontinuity orientation, blasting and rockmass stress adjustments to the CMRR is discussed. The effects of acid mine water on strata weatherability and the need to incorporate immersion tests using acid mine water are also detailed. In addition limited correlation is given between CMRR values and other geotechnical factors such as joint trace length, joint shear strength, joint orientation, weatherability and roof damage due to horizontal stress. Taking cognizance of these observations, a concept of stress induced roof damage triggering is discussed.

Jan 1, 2001

By Simon N. Lekakh, D. G. C. Robertson

A new integrated CFD-combined reactors approach is proposed for the description of processes in metallurgical vessels. CFD simulations were used to obtain the melt flow pattern in the vessels (ladle, tundish, and continuous caster mold). From these simulations, the characteristic curves were derived: (i) the residence time distribution curves (RTD) for flow-through systems (at tundish exit or at dendrite coherency surface in the mold) and (ii) the mixing curves for closed systems (ladle). In the next step, the melt flow was represented in a “combined reactors” system consisting of a combination of unit reactors (Plug Flow, Mixer, and Recirculated Volume). An inverse simulation was used to define the volumes of the reactor units and the melt flow rates between them by fitting to the characteristic curves from both methods (CFD and combined reactors). The suggested approach is demonstrated for multiple designs of Ar-stirred ladles, tundish, and SEN. This methodology can be used to enhance traditional post-processing CFD analysis and also as a tool for on-line process control.

Jan 1, 2014

By N Khalili, J Zhao, G F. Zhao

Toppling failure of a jointed rock slope was studied by using the distinct lattice spring model (DLSM). Compared with the classical discrete element model, the DLSM has the advantages of free calibration of micro-mechanical parameters and easy to represent discontinuities, and is more computationally efficient. In this work, the DLSM was used to investigate the toppling failure of jointed rock slopes. The numerical simulation was verified against experimental data from a centrifuge model test on a jointed rock slope. Both the horizontal deformations and failure pattern observed in the centrifuge test were reasonably reproduced using the DLSM. Then, the mechanism of the flexural toppling failure was studied numerically by using a parameter analysis. Finally, some insights were derived that may be useful for practical engineering.CITATION:Zhao, G F, Khalili, N and Zhao, J, 2014. Application of the distinct lattice spring model on toppling failure of a jointed rock slope, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 207–214 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By Jean Balech

This paper presents some results of dynamic loading tests performed on concrete piles driven in soft clay formation. The load transfer mechanism, measured in the dynamic increasing energy test (DIET), under blows of growing energy, is described in terms of mobilized normal forces diagrams and unitary local friction and displacements. It was observed that the lateral skin friction grows up to a maximum, in the soft clay layer and, gradually diminishes to a residual value when the system presents the maximum mobilized resistance. It may be concluded that the rupture load is not equal to the maximum mobilized point resistance plus the maximum mobilized local friction as suggested by most of static bearing capacity formulae.

Jan 1, 2002

By J. H. C. Pretorius, P. Nelwamondo

"Although South Africa possesses more than 80% of the world’s platinum reserves, its reputation for reliability in supplying platinum to global markets is under threat. This is due to the 49% decrease in output per worker (1999–2014), while the domestic costs have risen by more than 10% annually for the past 5 years. In addition, the continued decline in the commodity price by 38.3% (2012–2016) has resulted in a significant portion of the sector producing at a loss in 2015. The Chamber of Mines (now the Minerals Councilof South Africa) has suggested that solutions to improve productivity and reduce cost pressures are required. This research aims to provide operational excellence through the application of event chain project management (ECPM) to improve productivity and reduce operational costs. A case study was used to carry out research in platinum mines, with data collected using a motion-time study to measure the current efficiency of operations in each mining stope through actual activity durations. The results indicate that through the application of the event chain project management methodology, risks affecting the mining stope schedule can be managed, the efficiency of operations was improved by reducing the time spent on each activity, productivity was increased by shortening the project duration, and operational costs were reduced in the process. IntroductionSouth Africa’s total mining industry production was 4.9% lower in 2016 than in 2015; it decreased by 1.9% year-on-year in December 2016, with the main contributor to this negative trend being the platinum group metals (PGMs) with a drop of 15.1% and contributing -3.8% percentage points (Statistics South Africa, 2016). Although South Africa possesses more than 80% of the world’s platinum reserves, the 8% drop in production output since 2008 has put the platinum mining industry under the threat of being seen as an unreliable supplier to global markets. This decline in production is caused by the 49% decrease in output per worker between 1999 and 2014. In addition, the continued decline in the commodity price by 38.3% from 2012 to 2016 and an increase in operational costs during the same period resulted in a significant portion of the sector producing at a loss in 2015. A turnaround strategy is required to overcome these challenges. The Chamber of Mines has suggested, among others, the need for solutions to improve productivity and reduce cost pressures. The implementation of these solutions will ensure that the PGM industry thrives and reaches its potential of growing production to more than 322 t by 2020 (Baxter, 2016)."

Jan 1, 2018

By Xinyang Xu, Jirun Xu, Changlie Deng, Kang Yan, Luo Qian

Cake filtration is a complex process and the cake constructure is very difficult to describe in theory. Cake constructure parameters, such as the cake prosity, pore size shape and even its distribution, are main factors influencing the filtration results but have not been thoroughly understood yet. In this paper the fractal theory, an effective mathematical method in describing the self-similar phenomenon is used to investigate the filter cake constructure, and the scanning electron microscope and automatic image analyzer are used to measure the cake constructure. Cakes which formed in different condition are examined and the fractal dimension of the cake are calculated. The study shows that the constructure of the filter cake can be approximated by Sierpinski fractal geometry and that the fractal dimension of filter cake, related to the particle characteristics, slurry concentration and filtration pressure is a good parameter to describe the pore size distribution and the cake penetrability.

Jan 1, 1995

By Ihsan Berk Tulu, Ted Klemetti, Deniz Tuncay, Cicek Sena, Zhao Haochen

"Analysis of Longwall Pillar Stability (ALPS) and Analysis of Retreat Mine Pillar Stability (ARMPS) treat the pillar as a passive structure that is designed to carry overburden dead-weight. This dead-weight is calculated by simple rules based on the geometry of the mining, such as “tributary area theory,” “pressure arch theory,” and “abutment angle theory.” Although the pressure arch loading approach indirectly accounts for the generally stiffer overburden response of narrow and deep panels, it does not include the effect of specific geology of the overburden in load calculations. The relationship between successful pillar layouts and overburden geology can be incorporated into the load calculation by using the Ground Response Curve (GRC) approach.This paper introduces the GRC modeling methodology to investigate the effect of overburden geology and excavation geometry on load transfer mechanisms using seven field measurement case studies from four U.S. mines. It was also shown that the modeling methodology used to derive GRC in this study approximates mining-induced stresses and deformations within 5% of the values measured in the field.INTRODUCTIONFrith and Reed (2017) stated that current state-of-the-art pillar design methods ignore the overburden mechanics and use estimated dead-weight of overburden to compute pillar sizes. In the United States and around the world, overburden loading is typically estimated by simple geometric rules, generally with the tributary area theory (TAT). The specific overburden mechanics, structural competence of the overburden strata, geology, in situ stresses, and overburden/pillar interactions are typically ignored. However, these important mechanical responses affect the stability of the mine pillars and openings; therefore, they also affect the safety of the mine workers.Research conducted by the National Institute for Occupational Safety and Health (NIOSH) after the Crandall Canyon mine disaster (Esterhuizen, Mark, and Murphy, 2010) showed that small panel width-to-depth ratios and stiff-strong overburden result in a reduction of the observed pillar loads, much smaller than the TAT estimate. In fact, as a response to the Crandall Canyon disaster, Mark (2010) implemented a pressure arch loading approach into the latest ARMPS program to recognize the inherently greater stability of narrow panels at depth. The pressure arch approach is a first logical step to introducing non-tributary area loading into the practical ARMPS program. Although the pressure arch loading indirectly accounts for the generally stiffer overburden response of narrow and deep panels, it does not include the effect of specific geology and mechanical response of overburden in the load calculations."

Jan 1, 2019

By S. O. Moshier, L. S. Barron, J. C. Hower

The Hardgrove grindability test, commonly used in coal characterization, was conducted on 13 Mississippian carbonates from Kentucky, Tennessee and Illinois. The results demonstrated that the grindability increases with a decrease in the Si02/(MgCO3+CaCO3) ratio, with fine-grained and petrographically-complex stones having lower grindabilities. Also, the relationship between the Bond work index and Hardgrove grindability is significant.

Jan 1, 1993

By J Jasper, L Koroznikova, J Begelhole

This paper outlines a comparison of heavy liquid and heavy suspension separation methods for iron ore characterisation.As part of Arrium MiningÆs program to improve its knowledge of ore types being processed in its two hematite ore beneficiation plants (OBP), metallurgical evaluation of hematite feed for the upgrading process has become a major focus.Iron ore deposits almost always contain more than one valuable (and relatively dense) iron mineral. Iron ores are found with a range of iron contents, giving rise to density variations.At present the industry relies on heavy liquid separation techniques for the evaluation of iron ore samples arising from exploration, mining or metallurgical processes. There are only a few high-density liquids available, which are both high-cost and highly toxic.Low-toxicity solutions that can be utilised at relative densities up to 3.0 have been developed. However, highly-toxic organic liquids are required presently to achieve relative densities beyond 3.0.Bromoform which has a specific gravity (SG) of 2.89, and diiodomethane (SG 3.31) are commonly used; both present significant health and safety hazards.æClericiÆs solutionÆ (mixtures of thallium formate and thallium malonate) provide liquids having specific gravities between 4.0 and 5.0. ClericiÆs solution is highly toxic and testing is currently conducted by a limited number of laboratories worldwide.An alternative to ClericiÆs solution and organic liquids is a low-toxicity, high-SG, suspension technique, which has been demonstrated successfully for heavy mineral sands. This heavy suspension method employs mixtures of fine tungsten carbide particles in lithium heteropolytungstate (LST) solutions.Heavy liquid separation is not commonly used as part of routine iron ore feed characterisation due to the expensive, toxic and time consuming nature of the technique. Our results show that the heavy suspensions method can achieve low-cost, low-toxic separation and are outlined and results compared with results using ClericiÆs solution presented.Heavy suspension technique provides a theoretical/absolute separation of a particular sample. By placing an iron ore sample in a suspension of a particular density, it produces two products: a sink fraction and a float fraction. As iron oxides-hydroxyoxides are denser than the gangue minerals associated with the ore, particles that have high iron content will sink and the particles with gangue association will float. This process is repeated over several densities, thus also enabling separation of the constituent iron ore phases. A theoretical grade and a theoretical mass recovery can be calculated. With these calculations, a grade-mass recovery curve can be constructed for any element that is of interest.This type of characterisation can be used to either prepare OBP feed-piles of known processing characteristics, or to benchmark the performance of the process against what can be theoretically achieved on a continuous basis.CITATION:Begelhole, J, Jasper, J and Koroznikova, L, 2013. Application of the heavy suspension technique for ore beneficiation plant feed characterisation from the Southern Middleback Ranges, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 269-278 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By Larry Urbanoski

"This paper describes the application of a radioisotopic energy dispersive X-ray aY1alyser to complete on-stream analysis in a base metal concentrator.The major components of the system are outlined and some description of the application, operating experiences and benefits are provided.IntroductionThe ma1n intent of this paper is to describe the on-stream analysis system in operation at the Geco concentrator. X-ray analysis systems installed in Canadian concentrators to-date may be broadly classified as wavelength dispersive analysers whereas the installation described herein is an energy dispersive x-ray analysis system. Energy dispersive x-ray analysis techniques may utilize radioactive sources to provide primary x-rays for excitation of elements and separate the secondary x-rays on the basis of energy levels. In contrast wavelength dispersive analysers apply high voltage x-ray tubes to provide primary x-rays and utilize crystals to disperse and thereby separate x-rays generated by bombardment of the sample."

Jan 1, 1978

By Roland Heersink, Charles H. Wells

This paper discusses how a mill uses off-site data hosting approach to effectively utilize an entire suite of advanced applications to optimize daily operations, without incurring the overhead of on-site systems, staff and support. Details of the solution are provided, together with a live view of actual plant operations. Security and authentication mechanisms are also outlined so that users may gain an appreciation of the actual security of the remotely hosted data. A number of Web-hosted software applications provide direct connectivity to the database offering rapid and deterministic response times to clients. A 24x7 help-desk is available to authorized users from any Internet connected device. The paper shows how mill management advantageously use wireless PDA's to view what is going on at anytime and from anywhere. It concludes with a summary of how the approach is being used to speed decision-making and capture spot market opportunities.

Jan 1, 2002