Search Documents

By W. W. de Graaf, M. J. Ntsekhe

Klipspruit Colliery is experiencing coal losses, which leads to a negative impact on coal production and subsequently loss in revenue. This study aimed to identify the possible causes of coal losses in the No. 4 upper and lower seams. The objectives were to identify potential sources of coal losses through a literature survey, to identify areas where the coal losses occurred, to determine factors affecting coal losses, and to identify the most cost-effective methods to reduce coal losses. Highwall losses, top-of-coal losses, and coal edge losses were identified as the major areas of coal loss at Klipspruit. These losses were mostly attributed to the drilling and blasting practises of the pre-split, interburden waste, and the coal seams. Recommendations include re-visiting the current pre-split design and the tolerances adopted for the interburden and coal seam drilling and blasting design. It is furthermore recommended that Klipspruit implement a continuous improvement plan for the drilling and blasting and refresher training for the blasting crew and operators.

Jun 10, 2024

By B. S. Agbenuvor, R. Morrison, V. Jokovic, C. Antonio

Body breakage usually involves breakage of particles by compression between two surfaces or impacted against a rigid surface, with the latter of interest in this current study. This mode of breakage has been identified to be the most elementary size reduction process and the most effective breakage process in comminution devices. It has been found in the literature that the progenies produced from this form of breakage possess a residual velocity at which they move, after the breakage event. In the pursuit of efficiently utilising applied comminution energy, a laboratory-scale breakage device has been developed to deliver precise specific impact breakage using the concept of a fast-moving hammer and a slow-moving particle to effect breakage. The residual velocities of the progenies from the breakage event may be used to generate secondary breakage without further addition of energy if the particle encounters a stiff obstacle such as a steel plate at right angles to its path. To measure the extent of secondary breakage, the steel wall of the device was lined with a rubber material to suppress the second set of breakage events. The performance of the new device is analysed, based on calculated t10 values and measured residual velocities of the moving daughter particles. Testing involving anvils showed a much finer PSD and higher t10 compared to the test involving rubber lining. This finding is corroborated by the measured residual velocities of the progenies. The resulting energies calculated from the measured residual velocities of the progeny were found to be approximately 42-88% of the primary specific impact energy. This retained energy was found to be sufficient for secondary breakage. Keywords: Impact breakage, residual velocity, secondary breakage, energy utilisation

Jan 1, 2020

By Dunbavan M, Mallett C. W

The sequence of development and back analysis of the failure of a spoil pile in the 1B pit of the Moura Mine are given. The mode of failure was a two-wedge mechanism with a basal slip plane passing through a clay band about 2 m below the pit floor. Remedial actions for improving spoil pile stability are discussed.

Jan 1, 1981

By Nawal Kishore, Nilesh Pratap Singh, Amit Kumar Verma, Vikram Seervi

In India, despite its natural abundance, demand for coal exceeds its countrywide supply due to failure to achieve high production targets, especially in opencast mines, which are responsible for 94.98 percent of total raw coal production in the country. Employment of technological solutions, such as surface miners, is key to achieving higher coal production and productivity in an environmentally friendly manner, especially in populated areas adjacent to the mining zone. This technology eliminates blast hole drilling, blasting and primary crushing units, thus reducing related environmental hazards like ground vibration and fly rocks.

May 1, 2023

By S Wotherspoon

At Kalgoorlie Consolidated Gold MineÆs (KCGMÆs) Fimiston Operations, located on the periphery of Kalgoorlie Boulder in Western Australia, roughly 7.5 million tonnes of rock are broken each month for the extraction of gold. With the close proximity of neighbours to the mining operations in the Chaffers Cut Back, special blasting techniques and tools were employed by KCGM to manage the blast induced vibrations and noise in this area. The i-konTM initiation system coupled with OricaÆs complementary modelling and analysis tools offered the complete blast management package. With these tools KCGM management and Orica Mining Services commenced an investigation into the benefits of electronic initiation. Prior to the commencement of electronic blasting, initial modelling was conducted to examine the vibration time waveforms and their frequency content, as these were expected to have an impact on vibration interaction with structures such as large buildings and urban dwellings. This work looked at results measured for a previous conventionally (pyrotechnic) initiated blast in the area and compared it to the results obtained when the blast was modelled with electronic initiation and faster timings. The predicted peak particle velocity (PPV) and structural vibration factor (SVF) were calculated. From the results it was concluded that the investigation into using i-konTM electronic initiation system and SHOTPlus«-i blast design software had some real potential to improve blast vibration management on the cut back. The use of the electronic initiation system and complementary software allows intricate timing designs to be accurately placed into blasts. The system has a number of working modes that allow either the precise design timings to be logged automatically into each detonator or to be manually logged where a variation from the design exists. Where such variations from the design occur, the electronic system permits the actual timings used to be uploaded back into the design file. This allows both design and real actual timings to be stored for future analysis or reference.

Jan 1, 2004

By L. H. Morris, M. Mordecai

The emission of firedamp from the strata surrounding active workings of longwall coal faces normally follows a cyclic pattern associated with the mining operations being carried out on the face. Mining a coal seam disturbs the uniform distribution of overburden weight such that the working is enveloped by a region of high stress, both above and below the seam, advancing with the coal face. There is a decrease in stress as the strata is relaxed following the passage of the face (1). The paper describes experimental results obtained during the initial investigations of a study intended to examine the permeability of samples of coal measure strata under various triaxial stress conditions. Several investigators have studied the effect of stress on the permeability of rock, usually in the field of oil reservoir engineering. Two general lines of approach are evident. One used by among others Fatt and Davies (2), McLatchie et a1 (31, Brace et al (4) and Gunther (5) was to subject a rock sample to hydrostatic pressure. Gas or water would be passed through a sealed core mounted inside a high pressure hydraulic bomb. The second approach, favoured by Wilhelmi and Somerton (6) and also by Gray et a1 (7) was to employ a so-called 'triaxial' state of stress. Here radial confining pressure and axial stress are applied independently. The permeability is measured in the direction of the axial load. With the exception of Gunther who tested coals and Brace et a1 who tested a granite, the rocks used have been sandstones with permeabilities generally appreciably higher than British coal measure rocks.

Jan 1, 1971

By Greenwood J. N

This work was commenced at a time when information on the manufacture of cemented tungsten carbide was urgently needed in Australia. Much information of a general type has been published, but many of the details of the processes used are still undisclosed. The aim of this research was to determine a satisfactory way in which cemented tungsten carbide could, be made, and to investigate the problems which are associated with the process. As the work proceeded, its ramifications grew continually, and it was necessary to limit the possible lines of investigation. After much experimental work, a 9% cobalt-tungsten carbide alloy was developed which had satisfactory properties when used as a cutting tip. The effect of certain variables on the properties of this particular alloy was investigated.The tungsten carbide was prepared in stages from King Island scheelite concentrates under strict laboratory control, whilst the cobalt (1) used was made from cobalt oxide prepared from crude cobalt oxide obtained from Eisdon.In order to clarify the detailed experimental work, a brief summary of the method used for the preparation of cemented tungsten carbide follows.Tungsten carbide and cobalt are prepared in a very finely powdered state, and are then thor,oughly mixed by a ball milling operation. The resultant mixture is pressed in a suitably shaped die into small compacts which are subsequently '''presintered,'' i.e., heated' in hydrogen between 800°C. and 1000°C. The final sintering is carried out in hydrogen between 1,400°C.and 1,600°C. for about half an hour. These "alloys" may contain from 3 to 13% cobalt, depending on the particular properties required of them.PREPARATION OF MATERIALSThe tungsten oxide prepared as described by Smithells (2) was extremely finely divided, and after a few hours' grinding in a ball mill, the powder consisted of material below 10 microns iJ;l size. The oxide was reduced to tungsten metal with hydrogen in a tube furnace. The reduction was carried out at 800-900° C., a rapid flow of hydrogen being maintained in order to remove the water vapour' formed as a result of the reactions:

Jan 1, 1942

By Syed M. Tariq, Paul N. Worsey

Pre-splitting is now widely used to minimize overbreak and to protect final surface rock excavation profiles in large scale civil construction projects, open pit mining and quarrying. Jointing has been shown to affect the success of pre-splitting and the smoothness and integrity of the resulting rock face. Many facets of jointing have been investigated in detail, including the inclination of joints with respect to the desired pre-split plane, the effects of various filling materials, etc. However, the effects of joint frequency and spatial positioning has been paid little attention. The paper addresses this issue.

Jan 1, 1995

By F. Hassani, E. Aflaki, M. Nokken, M. Kermani

"This paper presents and compares the physical properties of Gelfill and cemented hydraulic fill (CHF) obtained by lab experiments. Gelfill consists of tailings, different binders such as Portland cement, fly ash and blast furnace slag and an alkali activator such as sodium silicate. The CHF and Gelfill samples with various mixture designs were cast and cured for 28 days. The influence of sodium silicate concentration, pulp density and mixing time on the mechanical properties of samples were evaluated using the uniaxial strength test. Mercury intrusion porosimetery (MIP) was used to analyse the microstructure of CHF and Gelfill samples.This study concludes that: (i) The mechanical properties of CHF can be improved by the addition of appropriate amount of sodium silicate. (ii) The rate of strength acquisition in Gelfill samples is faster than CHF samples over 28 days of curing period. (iii) Mixing time strongly influences the mechanical properties of Gelfill samples but did not have any effect on CHF samples. (iv) The MIP analyses indicate that the pore size distribution and total porosity of Gelfill and CHF were different, and this did contribute to higher strength development of the Gelfill samples. INTRODUCTIONThe increased depths of mines in the Canadian Shield and the high stress associated with these depths favour a new method of mine backfill that can both meet strength requirements and help mine productivity. The mine backfill mainly consists of tailings, water and binder materials, the latter being most expensive. Gelfill is a new mine backfill material whose binder usually consists of alkali activators such as sodium silicate and other cementitious materials such as blast furnace slag and normal Portland cement. Although sodium silicate has been used in concrete manufacture, the use of this material in mine backfill is relatively new (Doucet, 2007, Razavi, 2007). Until very recently there have been only a few isolated publications, mostly out of McGill University, regarding mine Gelfill (Razavi, 2007 and Kermani et al., 2009 and 2010). These papers have investigated some of the basic mechanical properties and mechanical behaviour of Gelfill. However, the physical performance of Gelfill in various conditions has yet to be understood. Therefore, the main objective of this study was to investigate the influence of mixing time and sodium silicate concentration on the mechanical performance of Gelfill and CHF through a series of experiments. Moreover, the microstructure of the Gelfill and CHF samples was studied."

Jan 1, 2015

By Syed M. Tariq, Paul N. Worsey

Presplitting is a now a universally accepted perimeter control technique in rock excavation. The success of presplitting and the smoothness and integrity of the resulting perimeter is largely dependent on the nature of joints in any given formation. Many facets of jointing have been previously investigated. The results of the effects of joints frequency and spatial positioning were presented by the authors at the ISEE annual meeting last year. This paper includes the results of further research into the mechanism of presplit blasting being carried out at the Rock Mechanics and Explosives Research Center of the University of Missouri- Rolla.

Jan 1, 1996

By D. Reddish

The combination of free standing steel supports, such as arches, and rock bolts (mixed support) has Frequently been in used in UK coal mine roadways when it is considered that the strata and/or environmental conditions would not be suitable for rock bolts solely. However, how such mixed support systems operate is not fully understood. Due to the differences in the support method provided by rock bolts and free standing steel, the total support generated is not simply a case of adding the contribution to the support of the roadway given by the two systems. This paper describes a numerical investigation into mixed support systems when used in coal mine roadways. A series of 2D and 3D geomechanical models are described and the method of modelling the rock bolts and steel supports in coal mine tunnels is discussed. The numerical models described include rock boltd only roadways, steel supported roadways and mixed supported roadways in a variety of geological and in-situ stress conditions. Conclusions are formed that allow an insight into mechanisms of strata reinforcement provided by the support systems modelled. Further to this, a review of the numerical modelling of pre-tensioned rock bolted systems is described identifying the contribution to support efficiency given by the adoption of tensioning in full column resin anchors. The results obtained highlight that the effectiveness of the pre-tensioned load is dependant on the rock mass quality and in- situ stress level at the site where it is to be used.

Jan 1, 2004

By S Ravn

Under platform exhaust (UPE) systems are often designed into metro stations as a means of removing heat generated by trains as they come to a halt in the platform. These systems are designed to extract heat from the brakes and brake resistors directly at the source in order to capture as much heat as possible before it can enter the public areas of the station, or contribute to the temperature build-up in the tunnels. Due to space requirements for the associated duct and air handling units, the UPE plays a significant role in the geometric design of the platform and station as a whole.In recent years questions have arisen as to the effectiveness of UPE systems. However, very little data is available for designers to use when making important decisions on the station designs for new metro systems. This is important as significant savings could be achieved by omitting or re-designing these systems for new build stations; not only due to the capital costs of space provision for the duct itself but also due to the associated operation and maintenance cost of the UPE system.This paper will present recent measurements of the UPE system of the Copenhagen metro together with one-dimensional (1D) simulations, looking at typical dispersion of heat into the station plenum box and air exchange through draught relief shafts as the train enters the station in order to evaluate the effectiveness of the UPE system. The aim of this paper is to disseminate the results of measurements and analysis to increase awareness of the issue and to provide discussion relevant to designers in their evaluation of heat removal systems in new build station designs.

Mar 8, 2011

By Metehan Erdogan, Ishak Karakaya, Fuat Erden, Emre Ergül

"The FFC Cambridge process was suggested as a promising Si production technique for the expanding solar energy industry. Direct electrochemical reduction of bulk SiO2 plates and porous SiO2 pellets in molten CaCl2-NaCl salt mixture were investigated at 750°C by applying 2.8 V potential difference. The produced Si powder was brown and found to be contaminated by the Ni and stainless steel plates used as the cathode contacting materials. The reduction rates of the bulk SiO2 plates and porous SiO2 pellets were compared from variations of current and accumulative electrical charge that passed through the cell during the electrochemical reduction. The amorphous bulk SiO2 plates were reduced slightly faster than porous pellets of crystalline SiO2. The overall reduction potential of SiO2 pellets against the graphite anode at 750°C in molten CaCl2-NaCl salt mixture was determined as 2.3 V by cyclic voltammetry. This potential was supported by calculations.IntroductionMetallurgical grade Si cannot be directly used in electronic industry and some intermediate steps are required to produce industrial solar grade silicon (SOG-Si). A promising alternative solar grade silicon production technique is the FFC Cambridge Process [1]. Production of Si by electrochemical reduction of SiO2 at 850oC in molten CaCl2 electrolyte was first studied by Nohira et.al. [2]. In their study; Si formation was observed on bulk SiO2 cathodes after 1 hour of electrolysis. Complete electrochemical reduction of porous SiO2 pellets was first reported by Jin and his coworkers [3]. The mechanism of electrochemical reduction of SiO2 to Si in molten CaCl2 was explained in another study [4]. Reduction rates of bulk SiO2 and porous SiO2 pellets were also compared previously and it was found that reduction rates for bulk plates were higher [5]. Furthermore, it was reported that mixing Si into porous SiO2 pellet increased the reduction rate [5]. Mo [2, 4-7], Ni [3, 8, 9] or Si [6] were used as cathode contacting materials in various studies. Yasuda et. al. [6] produced Si with 99.80 % purity using Si plates as cathode contacting material to reduce metal contamination."

Jan 1, 2012

By Isa Nozari, Asghar Azizi

The extraction of copper from sulfate leaching liquor was investigated using Acorga M5640 commercial extractant in kerosene diluent. The effects of important factors such as the extractant concentration, contact time, liquor pH, and temperature were examined on the separation factor Cu/Fe and the extraction efficiency of copper. The results indicated that nearly 92.32% copper was extracted from the leach liquor at 10% (v/v) Acorga M5640 concentration, 1:1 aqueous/organic phase ratio, 20 min contact time, pH 2.5, and 25 °C temperature. Also, the further increase in the values determined had no positive impact on the extraction of copper. Under these conditions, the separation factor Cu/Fe was obtained about 29.64. The extraction mechanism was studied applying the plot of log(D) – 2 pH against log [extractant] and it proved the association of two moles of Acorga M5640 for the extraction of one mole of copper. McCabe–Thiele diagram was constructed and a single-step extraction process was found to obtain themaximumextraction. Additionally, thermodynamic datawere investigated and the extraction process was endothermic and non-spontaneous at 298 K (ΔH = 27.05 and ΔG = 15.52 kJ mol−1). Moreover, the loaded organic phase was stripped and 80.94% copper was recovered after 20 min using 10% sulfuric acid concentration.

Jul 31, 2020

An Investigation into the Flotation Behaviour of Pyrrhotite Present in the Merensky Orebody

Sep 13, 2010

By G. A. Guess

THIS investigation was started with the idea of determining whether copper-nickel mattes might not have a lower flowing temperature than copper mattes, and thus perhaps aid in accounting for the difficulty so far experienced in attempts at pyritically smelting copper-nickel ores. We have used the term flowing temperature to avoid confusion with the usual melting temperature. The idea at first was that there might be a greater viscosity range in the one matte than in the other. In the early experiments it was in our minds to determine the relative fluidity of the mattes at a given temperature. Looking to this end we tried pouring equal quantities of matte at the same temperature down an inclined graphite slab, and comparing the distances traveled. Results from such experiments were not satisfactory. We next tried pouring equal quantities at the same temperature through a drilled hole in an Acheson graphite crucible, timing the flow with a stop watch, the whole operation being carried out in the muffle. The flowing temperatures of the mattes tried in this way appeared to be about the same, and there was no marked difference in their fluidity when well fused. Oxidation gave some trouble. These experiments finally led to the adoption of the following apparatus which we thought at the time was wholly original with us, but which we have since found was described by W. McA. Johnson.' The tray used was a slab of graphite 8 in. long, 2 in. wide and ¼ in. thick. It had six holes, into each of which sat a cup of Acheson graphite. Centrally in the bottom of each cup was a vertically drilled hole 3/16 in. in diameter and ½ in. long. The mattes to be tested were put into the cups, in a solid piece. The cups were covered with inverted Battersea "A" cups. The tray was put into the muffle of a gas-fired furnace. Supports on .each end held the tray about 2 in. from the floor of the muffle. Udder

Jan 6, 1916

By G. L. Gomes-Sebastiao, W. W. de Graaf

"Gomes Sand is a quarry operation that produces sand and aggregate for the construction industry. The quarry is experiencing inconsistencies in the fragmentation and poor pit conditions as a result of poor drilling and blasting practices. This results in excessive downtime in the load and haul and crushing processes.A benchmarking exercise of the blasting practices was conducted to evaluate the effect of the inconsistency on the mining cycle. After changes in the blasting practices the downtime was reduced, which improved the crushing plant utilization by 4.9%. The improved blasting practices and more consistent fragmentation decreased the average number of loads lost each month due to jaw crusher blockages from 9.2% to 3.9% of plant throughput. The change in blasting practices also improved pit conditions. IntroductionGomes Sand is a quarry operation that has been in operation since 2009, producing sand and stone for the construction industry. The quarry was experiencing unacceptable blasting results. The repercussions included uneven pit floors, large amounts of oversize rock (>500 mm), and inconsistent fragmentation.The blast results affected the load and haul operations as well as the efficiency of the crusher. This resulted in downtime in the daily operations, and consequent production and revenue losses.The crusher product should have a top size of 50 mm. A blast fragmentation of <50 mm would improve the downstream operations and the crusher throughput.An investigation into the blasting practices was carried out to assess whether the downstream delays can be eliminated by improving the blast results. The exercise included:* Assessing if the designed blast layout is adhered to on the bench* Observing the quality and control of drilling* Observing the charging procedure of the blast-holes* Benchmarking the fragmentation consistency of the blasted rock using current blast design and practices* Analysing the throughput of the crushing plant* Investigating the power consumption of the crushing plant and determine if a change in blasting practices will affect this* Evaluating the hours spent by the hydraulic hammer on secondary breaking."

Jan 1, 2017

By Bruno Bussière, Guosheng Zhan, Michel Aubertin, Vincent Martin, Robert P. Chapuis

The study evaluates the hydrological behaviour of exposed and covered waste rock dumps. The objectives were to determine the major factors influencing unsaturated flow in waste rock dumps and covers, and to improve the in-situ, laboratory and numerical modeling characterization methods. Using material properties obtained from in-situ and laboratory tests, waste rock dumps of different configurations, with and without covers, were modeled. It was found that a properly designed “Store, divert and release” (SDR) cover allows most of the water to be diverted downslope and discharged outside of the waste rock dumps. The SDR cover seems to work efficiently even in extreme storm events. The numerical modeling results show that the unsaturated hydraulic properties (e.g. air entry value and water entry value) of the materials largely control the infiltration of water into waste rock dumps.

Jan 1, 2005

By M. J. Nicol, R. P. Colborn

An investigation into the kinetics and mechanism of the oxidation of iron (11) by oxygen in aqueous chloride solutions By R. P. COLBORN Pr. Eng., Ph.D. (Natal) and M. J. NICOLt B.Sc. Hons., Ph.D. (Rand) A reaction mechanism for the oxidation of ferrous chloride by molecular oxygen is developed. and the appropriate constants are evaluated. The effect of a number of cations and anions on the rate of oxidation has been tested.

The aim of this research was to study the absorption characteristics of thermally dried fine coal from South African collieries. After milling to ?150 µm and pressure filtration, the samples were subjected to either air drying or thermal drying at 150°C. The samples were then put into a climate box at 28°C and at three different relative humidity levels, namely 30, 60 and 94 per cent. It was found that the equilibrium moisture content of thermally dried coal at a specific relative humidity was lower than that of air dried coal. The relationship between the equilibrium moisture content and relative humidity is described by 1 ? RH = exp (-KTMen). There was no relationship between the volatile matter content and equilibrium moisture content, but there was an increase in the equilibrium moisture content of the coal with an increase in mineral content. The moisture uptake rate increased with an increase in temperature and a decrease in particle size. A model is discussed that fitted the experimental data and gave a good prediction for changes in the conditions. There was no evidence of greater moisture absorption by thermally dried coal. Keywords: Fine coal, thermal drying, drainage, South Africa, drying

Jan 1, 2002