Search Documents

By Biao Zhou, Qian Li, Kuo-Chih Chou, Yi-Long Liang, Jie-Yu Zhang, Qun Luo

"In this work, the phase transformational behaviors and microstructural characteristics of 60Si2CrVAT spring steel were systematically investigated as a function of applied cooling rates in the range of 0.l-10°C/s. A quenching deformation dilatometer was used to austenize and quench. The dilatometric curves between length changes and temperature of samples suggest three characteristic stages could be identified as different ranges of cooling rates, which meets well with metallographic examination and the measured hardness results. As the cooling rate increases, the structure transformed from pearlite, granular bainite to finally martensite. The F + P and B zones are completely overlapping in continuous cooling transformation (CCI) curve, which indicates that this steel is difficult to become single bainite and shows good hardenability.IntroductionThe 60Si2CrVAT, a high-carbon low ally super-high strength steel developed from the ?OCT 60C2XFA and 60Si2MnA, is often used for coil spring of heavy vehicles and high-speed railway by hot deformation or cold deformation [1-3]. The addition of Si improves relaxation resistance significantly, through the refinement of tempered carbides as the result of the retardation of E -carbide conversion to cementite during tempering. Due to its deleterious effects on decarburization and toughness, the maxinJum content of Si has limited to 1.5 or 2.0% [4-5]. Additionally, V and Cr can improve sag resistance due to the precipitation of fine carbonitrides during hot rolling [6-7]. To best of our knowledge, the strengthening by precipitation of alloy carbides of Cr and V often referred to secondary hardening [8]."

Jan 1, 2013

By P Ridgeway, D Xie, M A. Somerville, S Jahanshahi, H Rogers, J G. Mathieson, Y Pan, N Haque, P Zulli, T E. Norgate, L Lu, A Deev

In 2006 the Australian steel industry and CSIRO initiated an R&D program to reduce the industry’s net greenhouse emission by at least 50%. Given that most of the CO2 emissions in steel production occur during the reduction of iron ore to hot metal through use of coal and coke, a key focus of this program has been to substitute these with renewable carbon (charcoal) sourced from sustainable sources such as plantations of biomass species. Another key component of the program has been to recover the waste heat from molten slags and produce a by-product that could be substituted for Portland cement. This paper provides an overview of the low-emission Integrated Steelmaking Process, progress made over the past seven years and the program’s future direction which includes proposed demonstrations of the technologies developed including large scale piloting and full scale plant trials.

Jan 1, 2014

By Jesús Contreras

Since the commencement of its activities in Huelva in 1970, Atlantic Copper has maintained a course of action that has been more demanding than the successive environmental legislations current at different times. As its primary objective it has sought compatibility between the protection of the environment and both its industrial activity and the social and economic development of the area in which its Metallurgical Complex is located. For this reason, since the seventies it has maintained a continuous programme of investments which have allowed it to attain its present environmental situation. As a consequence of the Environmental Policy of Atlantic Copper, in April 1998 it obtained certification for its Integrated System of Environmental Management (SIGMA) according to international standard IS0-14001, and under European Community Regulation 1836/93 (replaced by the 76112001) for the Eco-Management and Eco-Audit System (EMAS). The SIGMA formalises the environmental management practices of Atlantic Copper and engages it to have available a system that can be fully audited. Atlantic Copper was the first European Company in the non-ferrous metallurgical sector to obtain both the UNE-EN-ISO 14001 certification and the EMAS registration. The present paper reviews the actions by Atlantic Copper in environmental matters that have allowed it to achieve its present position. It also describes the coming stages of improvement planned and the modifications to be carried out in the near future, in particular the criteria for the selection of technologies on the basis of the concept of BAT (Best Available Techniques) introduced by the European Union, and always guided by the final objective of converting Atlantic Copper into a reference within the sector, comparable to the best designed and operated installations in the world.

Jan 1, 2003

By Pertti Koukkari

The novel Jarogain process combines treatment of the jarosite residue of zinc manufacturing and processing of arc furnace dust from steelmaking to a holistic recovery technology. The new hydrometallurgical approach is targeted to recover the major constituents (Fe, Zn, Pb) as well as valuable components such as Ag, Au, In and Ga from the jarosite-dust mixture as reusable concentrates. The fractionation process proposed by VTT and Aalto University takes advantage of jarosite being readily fine powder and directly available for wet chemical processing. Jarogain process provides an energy efficient opportunity for jarosite utilization as value added products. The experimental proof-of-concept of key stages of the process will be outlined with a comparison of available pyrometallurgical treatments of jarosite waste. The techno-economical assessment is based on estimated investment and variable production cost using the discounted cash flow (DCF) analysis.

By Ahmet Haxhiaj, Jaroslaw Drelich

"Both composition and porosity of pellets are the main parameters influencing the reductive melting process in water-jacket furnace during the roasting of sulfide lead concentrate. Roasting in a smelter located in Trepçë is done at about 9000C, for pellets which are composed of PbS, CaCO3, Fe2O3, and SiO2. In order to faciltiate the formation of slag in the reductive melting, the pellets must have the proper content of CaO, SiO2, and FeO, and porosity. The plant’s practice indicates that pellets with porosity of 18% do not melt adequately in the water-jacket furnace. The optimum porosity for the proper melting of pellets needs to be 32-40% and can be achieved when pellets are loaded with more than 10 wt.% CaO. Pellets with less than 10% CaO have a limited network of pores, such that reactive gases cannot reach the entire ore structure. Also, the composition of the pellets must satisfy the ratio of CaO : SiO2 : FeO = 1 : 1.2 : 1.8 to facilitate the formation of slag in the reductive melting process.IntroductionAgglomeration roasting of sulfide lead concentrate is an important phase in the production of lead by reductive melting [1-6]. The reductive melting process is a complex process with contradictory effects of several technological indexes which many times are hard to measure and determine. In this process, loading the water-jacket furnace with pellets of optimized composition and structure can reduce the consumption of coke, and achieve high level of lead recovery. Pellets (agglomerates) should be porous, but at the same time they should have necessary mechanical strength. ‘Self-melting’ ability of pellets is controlled by the types and quantities of fluxes blended into the pellet composition. Three major additives and their role are:"

Jan 1, 2011

By Aiyuan Ma, Tu Hu, Chenyu Sun, Yonggang Zuo, Hongying Xia, Jinhui Peng, Libo Zhang, Yongguang Luo

"In this study, the adsorption characteristics of tannin acid in aqueous solution were investigated using regenerated activated carbon (AC), with the aim to remove the tannin acid organic matter from the solution after zinc hydrometallurgy and Ge precipitation. Results showed the temperature has little effect on the adsorption ability (q.) of the regenerated activated carbon. The experimental equilibrium data were tested for the Langmuir and Freundlich isotherms. The adsorption equilibrium was better described by the Langmuir isotherm (R2 > 0.99). Pseudo first- and second-order kinetic models were used for describing kinetic data. It was determined that the kinetics of tannin acid removal was well fitted by second-order reaction.IntroductionGermanium recovery is a complex processes [1]. Hydrometallurgical processes are favoured and these are based on the precipitation of germanium as hydroxide or sulphide or alternately with tannic acid [2]. However, in the germanium recovery process, too much tannin is consumed by the germanium-tannins complexation process, and results in a high content of tannic acid remaining in solution, which is harmful to the valuable metal recovery [3]."

Jan 1, 2014

By Taegong Ryu

The thermal plasma process has been applied to the preparation of nanosized tungsten carbide (WC1-x). The reduction and carburization of the vaporized chloride by methane-hydrogen mixtures produced nanosized WC1-x powder, with a small amount of WC or W2C phase. The products were characterized using XRD, carbon analyzer, and TEM. The effects of plasma torch power, the flow rate of primary plasma gas (Ar) to generate plasma flame, and the addition of secondary plasma gas (H2) on the product composition were investigated. The tungsten carbide (WC1-x) powder had a particle size less than 30 nm. The powder was treated under hydrogen atmosphere to fully carburize the WC1-x, and W2C phases to WC as well as remove excess carbon in the product. Finally, WC powder with a grain size less than 40 nm was obtained.

Jan 1, 2008

By Thomas J. Keefe, O&apos

The effects of cobalt, B-naphthol, glue and antimony on the polarization behavior of zinc sulfate electrolyte were investigated. It was found that B-naphthol was beneficial in reducing the detrimental effects of cobalt while antimony and excess glue were each harmful. Since the nu cl eat ion over potential was insensiti1ve to coba1t, other regions of the polarization curve were used to indicate electrolyte balance. The low? current density area occurring in the reverse or anodic sweep direction was? often an indicator when an ?unstable condition existed. The two parameters evaluated were the degree of inflection in the polarization curve in the low current density region during scanning and the rate of current rise observed when the sample was potentiostated at -0.781 Volts (SHE). Using this technique, a two-additive system was shown to be desirable to control cobalt and antimony containing electrolytes. The structure of the deposits was examined using scanning electron microscope techniques.

Jan 1, 1985

By Zhucheng Huang, Ronghai ZHONG, Liangming Wen, Tao Jiang

The reduction roasting-magnetic separation and its strengthening of high silicon coal-containing mini-pellets by sodium additives were researched. The results show that the carbon gasification reaction and reduction of fine hematite in high silicon coal-containing mini-pellets with 3% sodium additives were enhanced. Comparing with no sodium additives, the gasification rate of carbon with 3% sodium additives reacting with CO2 for 40 minutes at 950 and the metallization rate of reduced pellets with 3% sodium additives after roasting for 35 minutes at 960 increased from 35.15% and 58.72% to 86.98% and 86.15%, respectively. The analysis of SEM equipped with EDS demonstrates that the inner pore of reduced pellets with 3% sodium additives was more developed and the iron grains size significantly enlarged, meanwhile, the iron grade of concentrate increased from 60.45% to 80.23% and the iron recovery rate decreased from 84.67% to 80.78% after grinding-magnetic separation.

Jan 1, 2016

By Tamas Kekesi

Anion exchange in HCl media is considered an efficient alternative to the combination of the conventional purification methods. Anion-exchange distribution functions have been determined for cobalt and the main impurity elements by the technique of batch equilibration. Results were confirmed by spectrophotometric investigations and elution tests. Based on the new and the available distribution functions, combined with the assessment of thermodynamic stability, a procedure of anion exchange separation has been devised to eliminate virtually all the impurities from the cobalt-chloride solution. Separation of copper has been enhanced by the introduction of a preliminary step under reduced conditions. The rest of the impurities are eliminated in a second anion-exchange step applying rinsing and elution stages under oxidized conditions. The optimum parameters of the procedure have been determined according to performance characteristics (purification ratios, yields and volume efficiencies) derived from the analysis of elution curves obtained with laboratory scale ion-exchange columns. Special computer programs have been developed to facilitate thermodynamic simulation, analytical correction and data processing.

Jan 1, 2003

By Hongli Wen, Guangkun Shen, Qiong Deng, Shoujian Huang, Min Gan, Xiaohui Fan

"Due to the low iron grade and high sulfur content, pyrite cinder is difficult to be directly used for iron-making. In this paper, technology of magnetic roasting -grinding and magnetic separation -acid leaching was put forward for reclamation of pyrite cinder. For pyrite cinder of TFe53.51%, S2.20 %, studies showed that good magnetic effect can be achieved at roasting temperature 650~7000, reducing atmosphere CO/(CO + C02) 10~20% and roasting time 10~30 minutes. In separation conditions of grinding size -0.045mm accounting for 96.09% and magnetic field intensity of 1240 GS, iron concentrate of TFe64.81 %, S0.18% and iron recovery rate 91.44% was achieved. Acid leaching was studied to strengthen desulfurization. Results showed that high-quality iron ore concentrate of TFe66.3 l %, S0.10% was obtained under the conditions of hydrochloric acid mass fraction of 5%, pulp density of30%, leaching temperature of70? and leaching time of2 hours.IntroductionPyrite cinder is produced as a by-product of sulfuric acid industry [1] Domestic production is more than 12 million tons every year and occupied area is over 10 million square meters [2,3]. The pyrite cinder outdoor not only pollutes air but also damages surrounding surface [4] It after treatment used for iron-making is an ideal reclamation approach for its rich iron which is commonly 40-60% [5]. But pyrite cinder gets low utilization for its low iron grade and high sulfur content in China [6]. Therefore, comprehensive utilization of pyrite cinder has profound significance to environmental protection and the development of domestic iron and steel industry."

Jan 1, 2013

By Tao Zhang, Wen-tao YU, Hai-bin ZUO, Jian-Liang Zhang

Sintering-pot tests and metallurgical performances of sinter with 4 kind of different Al2O3 contents are experimented in this paper. Results show: when the Al2O3 contents increase from 2.0% to 3.5%, acicular calcium ferrites in mine phase will be gradually replaced by plate-like iron calcium. The increase of Al2O3 contents will lead to the addition of liquid viscosity and the reduction of permeability of sinter bed. Sintering time will be prolonged. The rate of yield is stable basically but production is low; besides, the increase of liquid viscosity will decrease of drum strength. The change of permeability of the material layer will make RDI +3.15 decrease first and then increase when Al2O3 contents changed from 2.0% to 3.5%. RI of sinter shows a contrary trend because many open voids are formed by deterioration of liquidity first and then pores closed.

Jan 1, 2015

By S. Y. Tan

As CMOS devices are scaled down into nano-region, SiO2 dielectric is approaching its physical and electrical limits. High-k material has been investigated widely in recent years, and gate oxide take place growth oxide with Hf-based below 45nm gate length technology node has been shown. The phenomenon of interfacial property between bulk silicon and gate dielectric materials (HfO2 and HfSiO) was focused. A comparison of capacitance-voltage (C-V) characteristic of gate insulator was presented. Furthermore, the electrical property and thermal stability of high-k dielectric materials at various post deposit anneal (PDA) temperatures were established. The X-Ray diffraction technique was (XRD) utilized to analyze crystallization of the thin films, and the X-ray photoelectron spectroscopy (XPS) was applied for surface chemical bounding energy to identify the silicon and dielectric layers. Results show that HfSiO films have exhibited a superior performance on both thermal stability and electrical performance.

Jan 1, 2009

By L. L. Sutter

Fly ash is a by-product produced from the combustion of most hels including municipal solid waste. Currently, most combustion residuals are disposed of in landfills at a continually increasing cost and with questionable impact on the environment. Due to the presence of heavy metal compounds, municipal waste combustor (MWC) fly ash has the potential to leach these metals (e.g., lead and cadmium) above regulatory limits. The heterogeneous nature of MWC fly ash makes detailed characterization difficult. This research focuses on the identification of lead compounds in MWC fly ash. Samples obtained from the Olmsted Waste-to-Energy Facility in Rochester, Minnesota were examined in this study. The fly ash was fractionated into six size ranges and prepared as geological thin sections for analysis. The worked discussed in this paper involves using an electron microprobe analyzer to determine phase composition in MWC fly ash. In addition, backscattered electron imaging, digital image processing, and mineral liberation analysis software were used to determine phase distributions and phase associations as a function of particle size. Several lead containing compounds in several forms are identified. The results of this study show that lead can be identified in small sectioned particles which would not be apparent using normal backscattered electron imaging.

Jan 1, 1994

By Yanhui Liu, Xuewei Lv, Chenguang Bai

A thermodynamic model for determining the surface tension of molten slag by considering the surface tension and molar volume of the pure oxide component, and their ionic radii was extended to the slag bearing high TiO2 (varying from 80 to 67%) at 1973 K. The iso-surface tension curves for the FeO-TiO2-Ti2O3 ternary system at 1973 K are almost parallel to the FeOTi2O3 line. TiO2 plays a role of surface-active solute, and its surface-active effect is attenuating with increasing the TiO2 content. The iso-surface tension curve shifts away from the TiO2 corner, indicating that the surface tension of the ternary slag decreases along with the addition of SiO2. The reasons include the addition of SiO2 with lower surface tension and the decrease of the total ion moment at the surface. Both CaO and MgO can bring about that the iso-surface tension curve shifts towards the TiO2 corner, indicating that the surface tension of the ternary slag increases along with the addition of CaO or MgO. CaO has a more pronounced effect on increasing the surface tension of the ternary slag than MgO at an equimolar amount addition. The increase of the surface tension results from both the compositional change and the variation of the slag structure.

Jan 1, 2015

By Gunther Schimmel

Ag exudation in four different alloys (Ag-Cd, Ag-Sn, Ag-Sn-In and Ag-Zn) is characterized. The amount of exuded material is correlated with the volume increase due to oxide formation in dependence of the alloy concentration and different densities of the oxide and matrix phases. It is shown that all four alloys show similar amounts of volume increases, but different amounts of exuded material. It is concluded that internal stresses due to the volume increase cannot be the dominant driving force for Ag exudation. A gradient in the chemical potential of Ag that originates from the O concentration gradient inherent to internal oxidation is suggested as driving force. The exudation behavior is thus governed by the variation of the activity of Ag in the Ag fcc phase in the Ag-Me-O system that differs between the alloying systems.

Jan 1, 2010

By Jesse White, Tyler Salisbury

Research projects contain many stages of development from the conception of an idea to a fullscale commercial operation. The transition from laboratory-scale research to bench-scale roasting can represent a significant increase in complexity and cost, depending on how many variables are being evaluated. Thermogravimetric analysis (TGA) can simulate roasting conditions and produce a small sample for chemical analysis or materials characterization. A simultaneous thermogravimetric and differential scanning calorimetry (TG–DSC) can identify endothermic and exothermic reaction temperatures. Using thermal analysis, some of the process variables can be tested and eliminated such as ore and reagent blends, retention times, operating temperatures, and some atmospheres.

Jan 1, 2015

By Dale Zacherl, Andreas Buhr, Rainer Kockegey-Lorenz

"The microporous calcium hexaluminate insulating material SLA-92 has been introduced as an alternative to refractory ceramic fiber and other insulating refractory materials. Key properties associated with this product include: high chemical purity, long term high temperature stability up to 1500 °C, low thermal conductivity up to 1500 °C, and high thermal shock resistance. The properties of the new material and various applications in the steel and ceramic industries have been reported in previous papers. The current paper summarizes the industrial application experiences with innovative refractories based on SLA- 92 and discusses potential new applications in various manufacturing as well as energyrelated industries.IntroductionSLA-92 was introduced to the refractories industry in 1998 by van Garsel, et al. [1] as a new insulating raw material for high temperature applications, followed by investigations [2] of long term temperature stability for this new lightweight aggregate up to 1500°C.SLA-92 was developed as an innovative alternative to commonly used refractory ceramic fibers. It has unique properties regarding chemical purity and mineral composition and is a microporous, silica-free calcium hexaluminate (CA6 – mineral name: hibonite)."

Jan 1, 2010

By C. Liliane Carvalho

In the current study, bio-oxidation tests were carried out in shaking flasks with a flotation concentrate containing the sulphides pyrite, arsenopyrite and gudmidite. The tests were performed with mesophilic microorganisms (At. ferrooxidans) at 30 °C and also with the moderate thermophile S. thermosulfidooxidans, at 50 °C. The effects of (i) previous adaptation of the microorganisms to the concentrate, (ii) ferrous iron concentration and (iii) pulp density (2%, 4% and 6% (w/v)) on the dissolution of the sulphide were studied through arsenic extractions. S. thermosulfidooxidans was more sensitive to the pulp density in comparison to At. ferrooxidans as a reduction in sulphide oxidation was observed with the increase in the solid content to 6%. Therefore, the mesophilic strain was selected for further work, which comprised a rolling bottle experiment at 10% solids. After 40 days of bio-oxidation, the solid material was subjected to cyanidation, which revealed 85% gold extraction as compared to 21% from the original concentrate. The antimony sulphide grains in the bio-oxidized product showed similarity to what was observed in the original sample, suggesting such particles were not susceptible to the bio-oxidation process.

By Bhagyadhar Bhoi, Chitta Ranjan Mishra, Hara Prasanna Mishra

"In the Sukinda Valley of Orissa, India, the total quantity of nickel ore reserves comprising of both lateritic and chromite over burden(COB) have been estimated at around 231 million tonnes containing 0.3 to 0.9% Ni. While mining of one tonne of Chromite ore, around 6-7 tonnes of chromite over burden are removed. These overburden materials are disposed as waste materials, which causes lot of environmental hazards and ecological imbalance. India imports a large amount of nickel and ferro-nickel to meet its growing demands in various sectors. For import substitutions, efforts have been made to produced ferro-nickel from the lean deposits of nickel bearing lateritic ores/ chromite over burden materials by reduction roasting followed by magnetic separation and then the nickel rich magnetic fraction is smelted to produce ferro-nickel. It has been possible to produce ferro-nickel of grade varying from 4-25% nickel.IntroductionDuring mining of chromite ore, large quantities of overburden materials are being generated. The materials amount to approximately 10 million tones per year contain around 0.3-0.9% Ni, 0.02-0.06% Co, 20-50% Fe and 4-9% Cr2O3 depending upon the location and the depth of the mine. These materials presently do not find any application for the extraction of nickel due to lack of a suitable technology. The materials are also unsuitable for ferro-nickel making because of their very high iron to nickel ratio. The country is seriously looking for a suitable technology to utilize these resources as its entire domestic requirements of nickel is met though imports. In this connection, a systematic approach has been made at the Institute of Minerals and Materials Technology, Bhubaneswar to develop a process for ferro-nickel making from this indigenous resource."

Jan 1, 2011